Search Documents

1. In 2003, a total of 4,357 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). The major industrial classifications in stone mining are dimension stone (used for construction purposes), crushed and broken stone (aggregates), cement, and lime. • Stone mines comprised 30.3% of all mining operations. • Mines producing crushed and broken stone (n = 3,412) comprised 78.3% of all stone mining operations.

Feb 1, 2005

Illinois has the largest reported bituminous coal resources of any state and is one of largest coal-producing states in the nation. Coal-bearing rocks underlie about 65 percent of Illinois, including all or part of 86 of its 102 counties. An estimated 18 1 billion tons of coal resources are still in the ground. Using present mining methods, more than 30 billion tons of coal are classified as recoverable. This represents almost one-eighth of the total recoverable reserves of all types of coal in the United States. The state's surface mining regulatory program was conditionally approved June 1,1982. It received full approval October 25,1988. The Abandoned Mine Land Program was approved June 1, 1982, and the AML emergency authority June 11, 1984.

Jan 1, 1992

By Michael R. Yenchek

Contacts with energized conductors are a major cause of electrocutions in underground coal mines. Sensitive ground fault interrupters (GFI's) installed on in-mine three-phase ac utilization circuits would probably prevent the majority of these deaths. A sensitive GFI is a protective device that detects and interrupts small deadly ground currents in the milliampere range before those currents can cause ventricular fibrillation in humans. Commercially available three-phase sensitive GFI's have not been specifically designed for application in coal mines. The Bureau of Mines therefore tested three commercial GFI models to determine their worthiness for mine power systems. GFI design and construction, transient immunity, reliability, and time-current characteristics were evaluated in laboratory tests. No commercial device was found suitable for mine use without design modifications. The tests results will serve as a basis for the development of a mineworthy sensitive GFI in ongoing Bureau research.

Jan 1, 1985

By D. R. Corson

The Bureau of Mines instrumented two similarly backfilled stopes--one filled in the normal manner and the other with the fill densified using vibratory compactors--to evaluate the effect of fill compaction on subsequent vein-wall closure proposed as a adjunct process for strengthening cemented fill. Hydraulic pressure cells to monitor pressures within the fill and mechanical closure devices to measure vein-wall movement and the procedure for their installation are described. The field compaction work was generally performed manually by utilizing small commercial concrete vibrators. A prototype immersible vibrator using slusher cables to propel the vibrator in the stope was used on several lifts of fill. Although compaction efforts were less effective than anticipated in increasing the final density of fill, analysis of the field data does indicate somewhat improved strain characteristics and an increased pressure buildup for the densified fill. The effects of a prolonged period of inactivity and of rock burst occurrences in the immediate area are also reflected in plots of strain and pressure within the two instrumented stopes.

Jan 1, 1971

By W. L. Cooley, K. Y. Lee, M. M. Hassan

Because power system topographies for surface coal mines are significantly different from those for underground coal mines, the requirements for ground wire monitors for surface systems are somewhat different. This paper analyzes the problems faced by high-voltage ground wire monitors. Based on this analysis, some design requirements for monitors are suggested. Finally, results from laboratory evaluation of some of the commercially available monitors are presented.

Jan 1, 1979

By Joseph M. Pugliese

The U.S. Bureau of Mines has produced a generic in situ copper mine design manual, which contains a computerized cost model for in situ copper oxide mining. The model specifies (1) site-specific parameters, which must be quantified for mine design, (2) a method for minesite design based on those parameters, and (3) a procedure for assessing economic viability for the mine design. The menu-driven computer program performs calculations for developing commercial mine design specifications, as well as capital and operating costs. The default values are based on 1986 dollars, and indices for updating costs are included. The program also provides discounted-cash-flow rate of return (DCFROR) and allows for sensitivity analyses for an in situ mining operation at any specific undisturbed copper oxide deposit. This report is to be used with the 1990 version of the computer program, which has been made user friendly. It describes the flies, tutorial, input phase, help function, and monitor display of all calculated values and of the DCFROR table. The monitor-displayed discounted initial value of investment and annual operating costs are defined. The dual rate-of-return situation and sensitivity analyses are also briefly discussed. Information is provided on obtaining the computer program on diskette.

Jan 1, 1991

By Frank L. Hess

In 1876 cassiterite was identified in the placer gold from the northern Black Hills, and such a mixture could have come only from Nigger Hill or one of the streams draining the hill, because in no other part of the northern hills have cassiterite and gold been found together. Nigger Hill is in western Lawrence County, South Dakota, and on it is the little camp of Tinton. The Wyoming line runs along the west side of the hill and crosses the ridge which is the hill's continuation about miles north-northwest of Tinton.

Jan 1, 1938

By A. W. Ambrose

A few years ago, (March 3, 1915) Congress passed a law providing for the establishments of ten mining experiment stations under the supervision of the Bureau of Mines. In 1917 the Secretary of the Interior decided that one of these stations should be devoted to Petroleum, and in the early part of 1918, approved the establishment of the Petroleum Experiment Station at Bartlesville, Oklahoma, upon the condition that the city furnish the site for the buildings and guarantee $50,000. for the erection of the buildings. A building site of 5 acres and the necessary building fund was furnished by the Bartlesville Chamber of Commerce.The buildings consist of an administration and laboratory building, both of brick construction. The former is a two-story structure of eight rooms. A large room occupying over half of the main floor is devoted to the library, reception room, and clerical force. The remaining rooms comprise a drafting room and six offices occupied by the staff assigned to this station. The laboratory is a one-story brick building and contains a well-equipped chemical and physical laboratory, also a machine shop and mechanical laboratory. In addition to the main buildings there now are on the property an experimental refinery, a blue-print house, and a store house. These latter buildings are all of sheet-iron construction.

Oct 1, 1920

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost System The cost system reported here is a suite of computer programs which incorporates the logic and information flow structure as outlined in earlier chapters. Specifically, computer programs have been devel¬oped to: 1. compute labor, operating, and capital costs, 2. summarize cost and production data, and 3. compute the minimum acceptable selling price for coal. While the cost system can be executed independently, it is de¬signed primarily for use with the Master Design Simulator and there¬fore must conform to the overall system hardware. The computer model is written in Fortran IV for use with the IBM System 360/370 computers as well as with compatible units such as the Univac 1110 and CDC-6600. For ease in error detection and program modification, the model was constructed with a main routine and eight subroutines. The main routine reads and stores the data necessary for the cost computations and calls the subroutines in logical sequence. The subroutines perform the cost computations and data adjustments for reporting purposes. Each subroutine performs the cost computations for its particular com¬ponent of the cost cycle. The program operations are described in the following narrative outline. Control Subsystem As previously described, the main routine is a passive element, reading and storing input data and directing execution to the active subroutines for cost calculations. Figure 10 is a macro-flow diagram

Jan 1, 1975

By Nicholas G. Theofilos

Ecuador's real gross domestic product (GDP) increased 6% in 1976 despite persistent shortages of electrical power and essential fuels, which caused factory slow-downs and shutdowns. Petroleum export earnings, which made up more than 50% of total export value in 19716, totaled $565 million, a 9% increase over those of 1975. A new 60,000-barrel-per-day oil refinery at Esmeraldas was scheduled to go on- stream in mid- 1 97 7, operating entirely on Ecuadorean crude. Corpración Estatal Petró1era Ecualtoriana (CEPE) started construction of a 600-kilometer network of product pipelines which was scheduled to be completed in 1977 to coincide with the completion of the refinery.

Jan 1, 1980

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

By Louis C. Brichta

The Rush Creek district of Marion County, Ark., has had a more or less continuous record of zinc production over the past 40 years. The ore has come from many small mines working on oxidized and semi-oxidized deposits found in the Everton formation where that formation forms the present surface rock. Prospecting has been restricted to the hillsides above the creek levels, the actual ore outcrops being the guides. Little attention has been paid the possible sulfide zones. In August 1942, the United States Geological Survey and the Bureau of Mines recommended exploration of the Powell and Cotter formations, which underlie the Everton, for which purpose the Survey had previously located 18 proposed drill-hole sites in geological structures that seemed favorable to are deposition.

Jan 1, 1949

By Bowles Oliver

"Modification of Quarry Process.Limestone beds are formed by processes of nature, processes that have been in operation for thousands and perhaps millions of years. Therefore, their com- position and physical properties are long-established and unalterable features over which man has no control. He must take them as he fields them.It is undoubtedly true that the character of lime depends largely on the nature of the parent limestone. A high-calcium lime cannot be manufactured from a dolomite, nor can a pure lime result from the calcination of an impure raw material. However, in the process of turning limestone into lime man is not entirely helpless in his control of quality. Even though a deposit is variable in character a single lime product of uniform quality may be produced by judicious quarrying. A single grade of product may not always be desired, the producer may wish to supply the needs of a variety of users each demanding U different grade or quality of lime such a series of graded products may be produced in part at least by modifying the quarry method. Thus, by changes in quarry practice a single product or a variety of products may be made. The latter problem will be considered at a later time, and the present paper devoted to the first named question' that of producing a single grade of lime from a deposit of variable rock,It is realized of course that uniformity in the product is influenced greatly by manufacturing processes such as calcining' hydrating' grinding or storage, but the present discussion is confined to the influence of raw materials only. In considering the various devices that may be employed it is realized that much remains to be learned, and it is hoped that many operators will contribute to the discussion as they have already done in connection with previous papers of this series."

May 1, 1923

By Kenneth L. Rubow, Virgil A. Marple, Bruce K. Cantrell

"In a cooperative study by the University of Minnesota and the U.S. Bureau of Mines, diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and in five underground coal mines. Three mines utilized diesel-powered haulage equipment and two used all-electric equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations measured. The first technique, using a micro-orifice, uniform deposit impactor (MOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of the aerosol is predominantly submicron and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 µm. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling.Based on the results from the size selective sampling, a personal diesel aerosol sampler has been developed for measuring diesel aerosol mass concentrations. Th.is sampler uses an inertial impactor to size separate the respirable aerosol at 0.8 µm. All material less than 0.8 µm is collected on an after filter for subsequent gravimetric analysis."

Jan 1, 1990

By C. J. Walker

The Bureau of Mines undertook a theoretical and laboratory study to determine the feasibility of using ethylene as a tracer for natural gas in underground gas-storage reservoirs. The study indicated that ethylene was a useful gas tracer in underground gas storages. Tracer losses were not excessive. Laboratory tests were conducted at pressures as high as 500 psia in both wet and dry consolidated-sandstone cores, evaluating tracer loss with gas blends containing natural gas with different concentrations of ethylene tracer. Under certain conditions losses were less than 17 percent.

Jan 1, 1966

By John Nagy, Austin R. Cooper

Information is presented on the pressure and rate of pressure development during a dust explosion . The data were obtained in laboratory studies in a 75- cubic inch vessel with mineral , agricultural and chemical dusts . The factors investigated include dust concentration , oxygen concentration of the atmosphere , admixed inert powder , and admixed moisture . Information is given also on the effects of these factors on the composition of the atmosphere after the explosion .

Jan 1, 1964

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By John E. Hamak

The U.S. Bureau of Mines estimates the identified helium resources of the United States at 630 Bcf as of December 31, 1990. This includes 295 Bcf of demonstrated reserves, 87 Bcf of demonstrated marginal reserves, and 42 Bcf of demonstrated subeconomic resources. The identified resources include 161 Bcf of helium in inferred and marginal reserves and 45 Bcf in inferred subeconomic resources. The identified helium resources contained on Federal lands are approximately 170 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. In addition to the identified helium resources, undiscovered helium resources in the United States are estimated at a most likely volume of 103 Bcf, with a maximum volume of 259 Bcf and a minimum volume of 41 Bcf. Also reported are 43 Bcf of helium in nonconventional and low-helium-content natural gases. Current extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1990 was 2.5 Bef. If current trends continue, some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1993

By Frank L. Hess

In 1876 cassiterite was identified in the placer gold from the northern Black Hills, and such a mixture could have come only from Nigger Hill or one of the streams draining the hill, because in no other hart of the northern hills have cassiterite anti gold been found together. Nigger Hill is in western Lawrence County, South Dakota, and on it is the little camp of Tinton. The Wyoming line runs along the west side of the hill and crosses the ridge which is the hill's continuation about miles north-northwest of Tinton.

Jan 1, 1938