Search Documents

By T. G. Carnahan

The Bureau of Mines investigated a flotation-nitric acid leach procedure as part of the goal to maximize minerals and metals recovered from primary and secondary domestic resources. Studies were conducted on an ore that contained carbon-bearing and sulfide mineralization that rendered a portion of the ore refractory (resistant) to conventional leaching technology. The procedure investigated for treating the ore consisted of the following: (1) separation by flotation of the carbonaceous and sulfidic components from the ore, (2) leaching the flotation concentrate with nitric acid at 100° to 110° C, (3) leaching the flotation tailings with sulfuric acid, and (4) processing the combined leached slurries in a conventional manner to recover yellow cake. In step 2, HN03 is converted to gaseous products from which it is regenerated by reacting these products with air and water for further leaching. An overall uranium extraction of 96 pct was achieved by this procedure.

Jan 1, 1979

By Margaret M. Ragin

In a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research, with input from the phosphate industry, the conversion of phosphogypsum to sulfur has been investigated. The first step in the conversion scheme involves reduction of phosphogypsum to calcium sulfide. Effects of temperature, catalyst, reaction time, and type of reductant (carbon monoxide and coal) are discussed. It was determined that phosphogypsum could be reduced to calcium sulfide at 850° to 1,000° C using either coal or carbon monoxide as the reductant. The required temperature was lowered to 750° C using ferric oxide or magnetite as a catalyst for the reduction reaction. Results indicate that as the volatiles content of the coal is increased, reaction temperature may be decreased to obtain a given conversion, or if the reaction temperature is maintained constant, the conversion can be increased. Best results were 95- to 100-pct conversion using a high-volatile coal at 800° to 850° C. Addition of a catalyst increased calcium sulfide yield when low- or medium-volatile coals were used as reductants, but had little effect when high-volatile coals were used.

Jan 1, 1990

By J. J. Forbes

The Coal Mine Inspection Branch of the Health and Safety Division, Bureau of Mines, was established to carry out the provisions in Public Law 49, 77th Congress, H. R. 2082, approved May 7, 1941. The series of major disasters that beset the coal-mining industry in 1940 aroused public interest in mine-safety measures, and the act 18 the direct result of this rekindled interest. Under the provisions of the act, the Secretary of the Interior, acting through the Federal Bureau of Mines, is authorized and empowered to make, or cause to be made, annual or necessary inspections and investigations in coal mines, the products of which regularly enter commerce or the operations of which substantially affect commerce. The principal functions of the Federal coal-mine inspectors are to determine the causes of accidents and occupational diseases in coal mines and then endeavor to eliminate or ameliorate them (1) by revealing, through personal conferences with mine personnel, correspondence, and published reports, the unhealthful and unsafe conditions and practices existing in the mines and (2) by recommending practical means for correcting the conditions observed. The act does not provide any enforcement powers, and therefore compliance with the inspectors' recommendations is not mandatory; it does give Federal coal-mine inspectors the right to enter coal mines for inspection purposes.

Jan 1, 1951

Reduce worker exposure to respirable dust without interfering with bag-filling operations. Approach A dust control hood was developed which contains and captures dust close to its source and prevents it from entering the bag-filling operator's work place. How It Works A sheet metal hood is placed around the nozzle of the bag filling machine. The hood is connected through ducts to the plant exhaust ventilation system. Air pulled into the front of the hood and around the sides of the bag picks up dust generated inside the hood, and carries it to the dust collector. The size of the hood can be adapted to fit most fluidized valve-type bag-filling machines. The height of the hood depends on the bulk density of the product and weight of the bags being filled. The 14-inch-width of the hood allows it to be used on multi-nozzle baging machines spaced 16 inches on center. Only 2/3 of the bag is actually within the hood, and this allows easy operator access for placing the bags on the nozzle.

Jan 1, 1978

By James S. Browning

The purpose of this investigation was to develop a dependable and economic method for recovering spodumene and mica from pegmatites of the type found in Gaston County, N. C. Laboratory batch tests and continuous flotation tests were made by the Federal Bureau of Mines to determine the feasibility of treating the ore by flotation to recover high-grade spodumene and mica concentrates. The spodumene flotation circuit yielded concentrates containing 6.50 percent lithia (Li20), with an overall recovery of 81.8 percent of the lithia in the ore, The mica circuit yielded concentrates containing 97.5 percent mica, with a recovery of 82.5 percent of the mica in the spodumene tailing.

Jan 1, 1961

By John A. Johnson

Tests ere conducted at the Mount Weather testing adit of the 57 Bureau of Mines on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. Equipment Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is mace of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.

Jan 1, 1939

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

By John M. Gomes

The Bureau of Mines investigated two techniques for removing CaO from scheelite (CaW04) prior to electrolysis. In the first technique, a crude tungstic oxide (WO3) containing 0.15-percent lime (CaO) was prepared by digesting scheelite concentrates in hot hydrochloric acid. This oxide was used as cell feed to produce tungsten of 99.9-percent purity. The second technique used a high-temperature, two-phase separation, resulting in extraction of 99 percent of the WO3 in the halide-tungstate phase, while 90 percent of the CaO was retained in the silicate phase. Tungsten of 99.9-percent purity was deposited from the halide-tungstate melt after B203 and NaPO3 were added to form an electrolyte. The two methods were compared with a previously developed technique of depositing tungsten from scheelite concentrate fed directly to the electrolytic cell.

Jan 1, 1971

By W. E. Wallace, P. S. Raghootama, M. S. Seehra, C. A. Hill, M. J. Keane, P. Mike

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte hemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz, kaolin, and alumina dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect cf lecithin adsorption. Dust hemolytic potential versus media pH are presented. Fourier transform infrared spectroscopy and photoacoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis.Introduction Quarts dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and' progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction. In the alveolar spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, sagas other functions, mechanically stabilises the lung from collapse by reducing the surface tension of water in the alveolar sacs.(1) This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11% in dog lavage fluid). and phospholipids (about 88%).(2) Fhosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalaitoyl lecithin (DPL).(2) Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occuring upon deposition of a particle in a pulmonary alveolus.(3)"

Jan 1, 1988

By James V. Kelly

During the spring and summer of 1947, the Bureau of Mines conducted an investigation and core-drilling program in the vicinity of the Rodham mine, approximately 4 miles north of Shullsburg, Wis. This work was undertaken as a part of a general study of the zinc and lead-producing area of southwestern Wisconsin. Work in the Rodham-mine area was done to investigate further a mineralized area frilled in part by the Puritan Exploration Co., a Delaware corporation, with offices in Galena, Ill. Some significant lead-bearing samples were obtained, but no continuous ore body was disclosed as a result of the Bureau of Mines work.

Jan 1, 1949

By G. L. Cook

The design of a dual-inlet system for a Consolidated model 21-103C mass spectrometer is described in detail. The system permits both high-mass and low-mass samples to be run by using a single instrument. The difficulties of using a single instrument for both purposes are given and a method of minimizing these difficulties through the use of the present design is discussed, After examining the experience of five years of use, the conclusions are that the bimodal operation is practical and the low-mass analyses had nearly the same precision as before the modifications to the instrument were made. In 1951, O'Neal and Wier.5/ published the first description of the modifications made to a mass spectrometer so that the spectra of hydrocarbons with molecular weights up to 600 could be obtained. Further discussion of the equipment of O'Neal appeared in 1953.6/ Also, Brown, Melpolder, and Young7/ described a parallel inlet system designed to reduce sorption effects at room temperature.

Jan 1, 1960

Reduce the exposure of diesel vehicle operators to diesel exhaust generated during mucking in deadend drifts. Approach Direct the diesel engine exhaust upward and rearward thereby using the thermal buoyancy of the hot exhaust to form a layer at the roof, above the breathing zone of the vehicle operator. Modifying the Exhaust Outlets Diesel front-end loaders used in nocoal mines to remove blasted ore usually operate in entries open only at one end to cross cut ventilation. These deadend drifts are not usually ventilated with the use of auxiliary fans and vent tubing because of frequent blasting. The existing ventilation, therefore, is usually poor, and a diesel engine operating in such a drift emits exhaust which is not immediately swept away from the operator. On most load machines, the diesel engine's exhaust outlet is located near the floor and directed downward or to the side, so that when the hot exhaust is emitted, it mixes with the mine air as it rises into the vehicle operator's breathing zone. In this way, a uniform concentration of diesel exhaust forms around the operator.

Jan 1, 1983

By S. P. Kinney

[The blast-furnace operator is often confronted with the problem of determining the size of the materials which are used in the furnace burden. The statement is heard that the coke is larger or smaller or that certain ore is finer than that previously used. A screen analysis of the materials used gives a measure of the different sizes of materials in an aggregate. When one is fine and the other is coarse, the difference is obvious; but when the materials are of similar sire, it is more difficult to estimate the degree of finances or coarseness. In considering raw materials it would be desirable to be able to judge the size of the radio ideal materials entering the furnace and the burden as a whole, by one representative value, such as the average size of particle. Previous work by Perrott and Kinney3 developed a method for measuring the average size of particle in a mass of finely ground materials, and an attempt will be made to apply this method to the materials included in the blast-furnace charge and to the entire burden.]

Jan 1, 1930

By Oliver Bowles

From the most remote periods of civilization, stone Las been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns) or single markers to great obelisks and pyramid or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1050 at a cost estimated at a: high as $50,000,000, and it is today an object of unusual attraction for travelers. Other magnificent memorials, both ancient and modern, are to be found in many lands. Memorials of varying design have characterized the passing centuries and have found an important place in the New World. In early days, monuments were chiefly imported into America, but gradually an extensive memorial stone-manufacturing industry developed on this side of the Atlantic. Sales value of domestic memorials, f.o.b. quarry or mill, attained a maximum of $17,488,755 in 1920, and retail sales, of course, reached a much higher figure. Modest markers and tombstones are to be found in almost every rural community in the United States, and there are many elaborate and costly monuments in and near urban centers.

Jan 1, 1938

Data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 889 underground (6.0%) and 13,982 surface (94.0%) mining operations.1

Aug 1, 2009

By Chas. F. Jackson

This paper is a tabular compilation of data contained in a series of information circulars dealing with mining methods and costs at a large number of mines in the United States and some foreign countries. There circulars have been published from time to time during the years 1929 to 1934 inclusive. From time to time, as enough data became available in these circulars, other circulars and. bulletins have been published in which the data bearing upon different phases of nine operation were summarized, discussed, and analyzed. The present paper is a compilation of data on costs of drifting and crosscutting contained in earlier circulars, .designed to assemble this information in a convenient form for reference without attempting lengthy discussion of details of drifting and crosscutting practice. For such details the reader is referred to the circulars on individual mines.

Jan 1, 1935

By L. B. Pankratz

High-temperature heat-content values of gallium and scandium sesquioxides were measured over the temperature range from 298° to 1,800° K. The results fill gaps in the thermodynamic information for these compounds; no previous similar data existed. The heat-content values were combined with heats and entropies of formation to obtain free energies of formation of gallium and scandium sesquioxides to 2,000° K. The thermodynamic stabilities of the sesquioxides of aluminum, gallium, scandim, and yttrium were compared.

Jan 1, 1963

Reduce costs of recontouring surface mined land by improving bulldozer blades. Approach A specialized 48-foot-wide bulldozer blade set at an angle, a 13-foot bulldozer blade with swept-forward end sections, and a 24-foot grading bar are used in conjunction with conventional bulldozers to reduce the cost of recontouring surface mined land. How They Work The angle blade is used to do the initial and intermediate leveling of long spoil banks. It is mounted at an angle on two 410-horsepower crawler tractors in a side-by-side offset configuration, but requires only one operator since both tractors are controlled by a single set of controls. The angle blade usually begins its cycle at one end of the spoil bank where the operator fills the blade and moves forward, continuously cutting and casting the material to the repose slope. At the opposite end of the spall bank, the angle blade turns around and begins cut-ting and casting material to the opposite repose slope. This action continues until adjacent banks meet or the lateral distance from the center line of the spoil bank to the repose slope exceeds approximately 40 to 50 feet. At this distance, the sidecasting angle blade is no longer effective, and conventional bulldozers are used to do the final land shaping.

Jan 1, 1981

By Takashi Ohya, George V. Keller, Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications system which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a rela- tively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurements of ambient surface electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal-to-noise ratio at the surface. Numerous C.W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surface magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null in the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

By G. E. McClelland

The Bureau of Mines investigated chemical methods for producing high- purity gold from precious-metal-bearing zinc precipitates and steel wool cathodes. Precious-metal-bearing zinc precipitates and steel wool cathodes are unrefined products from conventional cyanidation and heap leaching-cyanidation operations. The zinc precipitates contained 14,40 pct Au and 0.35 pct Ag. The precious-metal-bearing steel wool cathodes contained 20.65 pct Au and 4.84 pct Ag. The precipitates and cathodes were treated with dilute acid to solubilize the silver and/or base metals. The gold-bearing residue was leached in dilute aqua reqia to solubilize the gold. High-purity gold was precipitated from the aqua regia solution with oxalic acid, sulfurous acid, sodium bisulfite, and gaseous sulfur dioxide. The leaching-precipitation experiments recovered 99.9 pct of the gold. The gold precipitates ranged in fineness from 997 to 999 fine. The chemical refining method provides a viable technique for the smaller operator to produce high-purity gold without using pyrometallurgical refining methods.

Jan 1, 1985