Search Documents

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals and investigations of their chemical and physical properties. The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures When placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld. County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

By R. W. Stahl

One of the broad purposes of the Bureau of' Mines since its establishment has been conservation of mineral resources. As some of the coal beds approach depletion, especially those coals suitable for making metallurgical coke, more and more attention is being given to means of recovering a larger percentage of coal in place. The customary system of mining in the United States is by room and pillar, or some variation thereof, which leaves pillars of coal to support, the roof. In many operations, where the pillars are not systematically recovered, the loss of coal often amounts to 50 percent or more of the original deposit. In many instances in developing new mines, It is planned to recover chain and barrier pillars on retreat when the mine has reached established boundaries. Too often, however, mines are abandoned for some unforeseen reason before completion of mining without recovering any pillars. Usually, these pillars are lost forever. With this in mind, the Mining Division, Region VIII, of the Bureau; of Mines is encouraging mining by longwall methods. It is a generally known fact that almost all of the European coal is mined by longwall methods, which are conducive to a high percentage recovery of coal. A comparison between mining systems usually is on the basis of tons per man per shift. Unless all operating conditions are similar, such a comparison could be misleading. Generally, the output per man shift in European longwall mines is less than that obtained in room-and-pillar mining in the United States. In European mining, maximum recovery of coal is not only mandatory but it must be accomplished without major damage to surface by subsidence. These restrictions necessitate packing or stowing with consequential increases In manpower and decreases in output per man shift.

Jan 1, 1954

By H. E. Peterson

This report revises an earlier publication by the Bureau of Mines on tungsten analytical procedures and expands the coverage by including appropriate procedures for the critical impurity elements that commonly occur in tungsten ores and concentrates (13).3 The basic methods described are not original, but many of the modifications to improve reliability and sensitivity were developed by the Bureau. Gravimetric and colorimetric methods currently used for the determination of tungsten in ores, mill tailings, and concentrates are described. Colorimetric procedures are preferred for low concentrations of tungsten, whereas either procedure is satisfactory for moderate concentrations. Conversely, a gravimetric method is preferred for the determination of tungsten in concentrates.

Jan 1, 1963

By Manuel Gomez

Dehydrogenation factors, proximate analysis, and ultimate analysis were examined as predictors of the low-temperature -carbonization properties of coals varying in rank from lignite through anthracite. All factors studied contributed to reduction in variance of the sample populations investigated. Response surface regression models based on variables from proximate and ultimate analyses of coal were constructed for eight low-temperature carbonization assay product and gas component Fields. These models were tested with independent samples that included drill cores, sized fractions, petrographic fractions, and run-of-mine coal. The models developed were used to predict low-temperature carbonization yields or coals from major fields of Wyoming. This information was cast in the form of contour plots describing the potential low-temperature carbonization product yields of Wyoming coals and the properties of the resultant char or coke. The variables used as input v the models may be measured and collected during exploration; thus, the carbonization properties of a seam can be determined in advance of mining. The information presented in this report is useful in that it broadens the deciionmaking base for management when either mine locations or coal conversicl plant sites, or both, are being considered.

Jan 1, 1971

By N. A. Eilertsen

This report describes field investigations conducted in 1953 of two occurrences of manganese and a separate magnetic anomaly in the Southern manganese district of Aroostook County, vicinity of Houlton, Maine -the Pierce deposits, in Hammond Plantation Township; the Burnham anomaly, also in Hammond Plantation; and the Nickerson-Farm prospect in Hodgdon Township. The manganese occurs in a thinly laminated sedimentary rock containing manganiferous carbonate interlayered with fine-grained metamorphosed sediment, rich in chlorite or hematite. The surrounding rocks are mostly dark gray-green slates. Samples composited for metallurgical testing from the Pierce deposits and the Nickerson-Farm prospect assayed 9.0 to 12.3 percent of manganese. More than 90 percent of the manganese could be extracted with sulfuric acid, but in most instances 30 to 40 percent of the iron was also extracted. Leaching tests indicated that, after being reduced in a hydrogen stmosphere at 600° C., about 85 percent of the manganese could be selectively extracted by a solution of ammonia-ammonium carbonate with iron extraction of only 14 percent.

Jan 1, 1958

By G. M. Potter, F. S. Wartman, M. D. Schmid

"In matte smelting of copper it has been established that the sulphpr present will combine with copper as long as the latter is present, and that thereafter it will combine with iron. The Cu-Fe ratio in the matte is determined by the Cu-S ratio, presumably owing to the much greater affinity of copper for sulphur or, expressed thermodynamically, the greater stability of copper sulphide in contact with silicate slag. Now, the work of Fournet and of Schütz, which is quoted in many elementary metallurgical texts, indicates that manganese ranks ahead of copper in its affinity for sulphur. Hence, we might expect that manganese could be concentrated from its admixture with iron. Compounds by matte smelting, and Rotts / has patented such a process. This greater affinity of manganese or sulphur is used to advantage in iron metallurgy, also, in which it is well-known that sulphur will combine with manganese and separate from metallic iron as manganese sulphide. Manganese sulphide,however, is quite soluble in silicate slags. 5/ The loss of manganese in slag in any attempted matte smelting is therefore great.If this solubility of manganese sulphide is slag is a physical one and the reaction MnO + FeS MnS + FeOIs substantially complete, then it might be expected that the addition of copper sulphide, which is almost entirety insoluble in slag, would serve to extract the manganese sulphide with the formation of a manganese-copper matte on the other hand, if an equilibrium exists in the above reaction, a copper sulphide layer would displace that equilibrium in one direction or the other, according to whether iron sulphide or manganese sulphide were more soluble in the matter layer."

May 1, 1937

By R. R. Backer

The Bureau of Mines, in cooperation with Washington Irrigation and Development Co. (WIDCO), evaluated the dewatering of fine coal-refuse slurry using chemicals and various types and combinations of drains in natural earth impoundments. About 40 lb of lime and 2 lb of polymer per ton of dry solids were mixed with the underflow from the preparation-plant thickener. Clear, free water was immediately liberated from the slurry. The percent solids by weight of the slurry increased from about 17 to 30 immediately, and after 5 days increased to 45 wt-pct. This indicates a threefold reduction in total volume after 5 days from 172 cu ft/ton solids originally to 56 cu ft/ton solids.

Jan 1, 1981

By D. R. Tesarik, M. K. Larson, D. K. Denton, J. B. Seymour, R. L. Rains, T. J. Williams

Because backfill has occasionally collapsed into an active working area, posing a hazard to miners, engineers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and Hecla Mining Co. installed instruments in a cemented, backfilled, stope-ramp intersection at Hecla’s Lucky Friday Mine, Mullan, ID. The purpose was to measure stress and strain changes in the backfill and reinforcing members during undercut mining. The instruments were monitored for 6 months while three successive cuts were mined below the intersection. Readings showed induced loads up to 3450 kPa (500 psi) in the backfill as stope walls converged 2.5 to 12 cm (1 to 5 in). The backfill then deformed against the top and bottom plates of the 2-m- (6-ft-) long vertical rock bolts installed as reinforcement, producing loads to 177 kN (40,000 lb)on the rock bolts. We hypothesize that a compressive zone was created in the backfill that allowed the backfill to remain stable as long as the compressive zones from adjacent rock bolts overlapped. This hypothesis is presented in graphical form. Of particular interest was the effect of loading on trusses installed to augment the vertical rock bolts and wire mesh typically installed in backfill. Data from the instruments indicate that wall closure perpendicular to the vein induced loads in truss legs parallel to the vein and in the rock bolt driven through the center of the truss, but, because they are designed to function under tension, truss legs perpendicular to the vein supplied in significant support as a result of compressional forces from wall closure. Based on this study, use of trusses was discontinued, and an alternative support system of wood beams and posts was installed as needed to ensure the safety of miners working beneath the backfill in stope-ramp intersections.

Jan 7, 2001

By R. H. Storch

The work described in this report was part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. Part of the program included churn drilling of alluvial deposits that previous preliminary testing, primarily for rare minerals, had indicated to be potential sources of titanium minerals. The first spot churn drilling began in the Deadwood placer area, Valley County, Idaho, in July 1956 to determine both the amount and grade of the ilmenite, FeTi03. Ten holes, ranging in depth from 6 to 40 feet and aggregating 251 feet, were drilled; 54 samples were taken. The samples were sent to the Spokane field laboratory for concentration and visual estimation of the amounts of the more common minerals in the heavy sand concentrates. For specific determinations samples from each drill hole were composited and shipped to the Bureau of Mines laboratory in Albany, Oreg., where petrographic, quantitative X-ray spectrographic, and chemical analyses were made.

Jan 1, 1958

By R. B. Stroud

Bureau of Mines studies of copper-bearing Permian red beds, which extend from north-central Texas through western Oklahoma to southwestern Kansas, indicate heretofore undefined commercial possibilities for low-grade, medium-volume, strip-mining operations. Potential ore bodies are indicated containing 0.5 to 1.5 percent copper in zones 6 to 12 inches thick. Cost analysis studies indicate a commercial operation is feasible for a hypothecated 1,000-ton-per-day ore mining and milling complex where a maximum of 60 feet of overburden can be stripped in mining a seam of shale 12 inches thick containing 1.2 percent copper

Jan 1, 1970

By Paul R. Coyle, Anthony T. Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and LaurelHill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super-pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereo net, and rose diagram projections so that the Loyalhanna’s structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts, pillar sizes, etc., that lessen miner exposure to these hazards.

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968

By Nicholas Kyriazi

A performance comparison of 14 rescue breathing apparatus was undertaken as an assessment of past and present worldwide technology. Rescue breathing apparatus are self-contained, closed-circuit breathing apparatus used for entry into areas having atmospheres that are immediately dangerous to life and health. Apparatus tested were the Biomarine BioPak 45, 60, and 240; the Draeger BG 4 and BG-174A; the Litton LITPAC II; the MSA Custom 4500 II Air Mask, Chemox, and McCaa; the Sabre Selected Elevated Flow Apparatus (SEFA); the Scott Rescue-Pak; the Siebe Gorman Aerorlox and Proto Ten; and the SurvivairLP-120. The apparatus were tested on an automated breathing and metabolic simulator at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH). Physiological parameters monitored during the testing were average inhaled CO2 and O2, minimum inhaled CO2, inhaled wet-and dry-bulb temperatures, and peak inhalation and exhalation breathing pressures. The metabolic demand on the apparatus was 1.35 L O2/min for most of the test with two 5-min intervals of 2.5 L O2/min, the first beginning 10 min into the test and the second beginning 10 min before the end of the rated duration of the apparatus. Results presented include apparatus service life and test-averages of monitored physiological parameters. Schematic drawings and photographs of the apparatus are also included. The Draeger BG-174A and BG 4 had the highest durations—295 and 291 min, respectively. The BG 4 hadthe lowest minimum inhaled CO2 levels, attesting to the effectiveness of its CO2-absorbent canister. The SabreSEFA had the lowest average inhaled CO2 levels, due mostly to the apparently low-dead-space mask andnose cup. The MSA Air Mask, the only open-circuit device tested, had the lowest wet- and dry-bulb temperatures, with the liquid-O2-source Siebe Gorman Aerorlox having the next lowest temperatures. The only apparatus with a CO2-absorbent not in a packed-bed design, the BG-174A, had the lowest exhalation pressures. The BG 4 had the highest level of positive pressure, with the Biomarine BioPak 60, Survivair LP-120, SEFA, and Litton LITPAC II nearly as high. The BG 4 had the lowest pressure swing, with the SEFA a close second.

Jan 10, 1999

By J. M. Kuchta

The chemical and thermal criteria used for predicting the spontaneous combustion hazard are briefly reviewed and data are presented to characterize the gas desorptions and self-heating tendencies of 29 U.S. coals. Closed vessel desorption experiments showed that CO, CO2, and CH4 are the main gases evolved and that the CO, CO/?O2 index, and 02 absorption rate increase with decreasing rank and increasing oxygen content of the coal. In this Bureau of Mines report, the effects of temperature, moisture, and other variables are discussed together with the application of the data to the complex conditions encountered in a mining environment. An important finding is that the presence of CO alone in a mine is not necessarily an indication of a self-heating reaction of the coal. Based upon experiments conducted in an adiabatic-type calorimeter, the self-heating temperatures of lignite and subbituminous coals can be as low as 30° C, whereas the bituminous coals require a temperature of about 60° C or more. The self-heating hazard is greatest when the coals are dried and exposed to a high humidity condition, apparently as a result of the "heat-of-wetting." Generally, the hazard is greatest with the western coals of the United States.

Jan 1, 1980

By A. B. Whitehead

A spectrographic method for the determination of 18 impurities in cerium is presented. The carrier distillation technique is utilized to separate the spectra of impurities from the complex spectrum of cerium. Metal samples are ignited to the oxide, mixed with silver chloride carrier containing an internal standard, and excited with a 20-ampere direct-current arc. An additional exposure, made after carrier depletion, provides for the determination of refractory elements. Experiments to determine the best carrier, sample-carrier ratio, electrodes, arc current, exposure conditions, internal standards, and any matrix effect are described. The relative standard deviation of the method at the 20- and 200-part-per-million levels is about 25 and 15 percent, respectively. The average relative error is about 20 percent in the 10- to 1,000-part-per-million concentration range.

Jan 1, 1962

By J. D. Marchant

Solid-state electrotransport of impurities in cerium, lanthanum, and praseodymium, using a pulsed current, was investigated. The results were compared with those of using a steady current. Impurities that showed appreciable movement with the pulsed current, but not with the steady current, were as follows: Molybdenum and oxygen in cerium, aluminum, iron, and molybdenum in lanthanum. The use of a pulsed current enhances the practical application of solid-state electrotransport to remove a wider variety of impurities from the host metals.

Jan 1, 1971

By Roy L. Wilfong

Infrared reference spectra are presented of compounds of importance in lead sulfide flotation research. Included are the spectra of several short chain alkyl xanthates of lead and zinc, the corresponding dixanthogen compounds, and the common oxidation products of lead sulfide and their sodium analogs. The spectra of several frequently used industrial flotation reagent xanthates are also presented. A thorough, well-documented discussion is given of the various corrections made to correct the as recorded absorption band data to near absolute values.

Jan 1, 1974

By A. J. Kraemer

For a number of years the Bureau of Mines has conducted semi-annual survey to determine the changes in the characteristics of the rotor gasoline being sold in the United States. Certain cities have been decided upon as points of origin of samples. Tare choice of these cities has been governed by their situation as the representative of a more or less definitely bounded marketing territory. Samples have been taken on or about the fifteenth day of January and July of each year. In the collection of the samples an attempt has been made to get a representation of the important types of motor fuel being sold, and also to tame into consideration the proportion of tie total consumption that is supplied by the different marketers. It is therefore felt that the survey affords a reliable indication of the quality of the gasoline being sold throughout the United States at the time of sampling. The figures in Table I, below, were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10 per cent (85 samples) having the highest end points, and the 1C per cent having the lowest end points were averaged. These averages are represented in the table as the "Maximum 10 per cent" and the "Minimum 10 per cent", respectively. The same scheme was used in the succeeding surveys.

Jan 1, 1925

By Charles L. Kimbell

In broadest overview, UN global industrial production indicators released and shown in table 2 suggest that the extractive sector of the world's mineral industry in aggregate registered a very slight upturn in 1991 relative to its 1990 performance. It also shows a continued rebound in the industry from the recessionary period of the mid-to late-1980's. These same indicators as calculated in late 1991, however, reflected a very minor downturn in extractive mineral industry operations between 1989 and 1990. This latter downturn represented a notable revision from the data reported in the immediate previous edition of this chapter, which suggested a tiny upturn. The apparent slight 1991 upturn in extractive sector industrial output generally was not mirrored in the performance of the processing sectors of the global mineral industry. Although the aggregate index for the chemicals, petroleum, coal, and rubber products manufacturers (see table 3) showed a notable gain in 1991, similar indices for nonmetallic mineral products and for base metals registered declines between 1990 and 1991. Examination of regional performance indices shows that the difficulties experienced in 1990 in maintaining output levels within the countries that formerly constituted the CMEA were reinforced by trends toward reduced gains in output levels, if not actual reductions in output, in several other areas. Generally speaking, the traditional developed market economy countries recorded downswings in overall industrial activity in 1991, particularly after midyear, whereas developing market economy countries logged gains. The developed market economy country downturns, however, were not nearly as significant as were the downturns recorded for the former centrally planned economy states - those that before 1992 were either constituent Republics within the U.S.S.R. or the latter's CMEA partners.

Jan 1, 1993

By A. D. Hahn

This report describes reconnaissance by the Bureau of Mines of titanium-bearing beach sands on Ship Island in the Gulf of Mexico off the south coast of Harrison County, Miss. The purpose was to determine the ilmenite, rutile, and associated heavy-mineral content of black-sand-bearing beach sands. The investigation was part of a survey of titanium resources of the United States. Ilmenite (FeTi03), an iron-titanium oxide, is the major titanium-bearing mineral consumed in the titanium pigment industry. Rutile (TiO2), titanium dioxide, is used mainly as a constituent in welding-rod coatings and in producing titanium metal. The major fieldwork was conducted during the first half of February 1961. Nine holes, totaling 220 feet of bore, from which 110 samples Her taken, were drilled at widely spaced intervals on the island.

Jan 1, 1962