Search Documents

By F. D. Everett

The exploration work on a seleniferous tuff deposit near Lysite, Wyo., was confined chiefly to an area of approximately 1 square mile selected on the basis of prior examination and sampling work by the Bureau of Mines. This area was superficially explored by digging and sampling over 2,000 feet of trenches and 15 test pits. The surface sampling indicated that the deposit might contain a multimillion-ton reserve of easy-to-mine volcanic tuff assaying more than 0.01 percent Se. Later, 11 holes, ranging in depth from 57 to 135 feet and totaling 929.4 feet, were drilled under contract using a dry rotary drill. Samples for assay were cut at 5-foot intervals or at noticeable physical changes in the formation being drilled. Of the 206 samples assayed from the drilling, only 8 contained more than 0.005 percent selenium, and 2 of these assayed as high as 0.012 percent Se. Chemical analyses of samples obtained from six holes drilled by the Nugget Coal & Timber Co. to the south of the area explored by the Bureau of Mines showed that no selenium-bearing formations were encountered in that work. Two of 72 samples taken from 42 validation pits dug by claim holders contained more than 0.005 percent selenium. The exploratory work established that the selenium mineralization is erratically distributed in small irregular bodies and is not confined to any one tuff bed. Because of the lack of correlation between the infrequent showing of low-grade tuff, neither the extent nor grade of the reserves could be calculated.

Jan 1, 1957

By M. D. Schlesinger

As part of the development of processes for producing synthetic fuels from coal, the Bureau of Mines prepared a special jet fuel in a pilot plant for evaluation by the Air Force. This jet fuel had all the required physical properties, including the important specifications of high heating value and high density. However, the finished fuel did not pass the stability test specified by the Air Force and conducted by the Southwest Research Institute in a high-temperature research coker. The cause for this instability is being investigated because pure compounds of the type identified in this fuel are known to be stable. The tar acid oil used was a 230° to 300° C. fraction of low-temperature tar obtained by carbonization of a West Virginia bituminous coal in the pilot plant of the Consolidation Coal Co. Both the desulfurization at 400° C. and saturation at 300" C. were done in the vapor phase at 2,500 p.s.i.g. After catalytic treatment and distillation the final jet fuel had a boiling range of 194° to 247° C., a net heating value of 18,420 B.t.u./lb. and a specific gravity of 0.8463 60° F./60° F. It also had u pour point below -62° C., and at 0° C. its viscosity was 4.5 cs. The oil was virtually all bicyclic, 41 pct. noncondensed and 56 pct. condensed.

Jan 1, 1961

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By H. H. Schrenk

One phase of Bureau of Mines work in health and safety, is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus,3/ gas masks, supplied-air respirators (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks),2 dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch, approval tests of other types of respira- tory protective equipment are conducted by the Health Branch, These branches are in the Health and Safety Division.

Mar 1, 1948

By J. E. Zeilinger, John Nagy, Irving Hartman

"INTRODUCTION Experience and research have shown that an effective way to reduce structural damage from explosions is to provide adequate pressure-relief vents in the walls of equipment and buildings within which explosions might occur. In general, free or unrestricted openings represent the most efficient type of vent. However, in many manufacturing operations it is impractical to use free vents, and it becomes necessary to cover the openings with diaphragms or blow-out disks, hinged panels, or other devices, in order to give protection against weather changes, to prevent the efflux of dusts or vapors from equipment during normal operations, or for other reasons.A few data on the pressure-relieving capacities of hinged panels and a paper diaphragm were published in Bureau of Mines Report of Investigations 3924,4/ which covered the first phase of the dust-explosion venting study made by the Bureau. The present report describes recent experiments that were made to determine the relative effectiveness of an unrestricted vent and 22 types of closures, including various paper, cloth, and metal-foil diaphragms, hinged doors or panels, and several kinds of scored and unscored glass panes.The tests showed that many of the vent closures were effective in releasing the explosions rapidly during their incipient stage, so that the development of destructive pressures was prevented. Vents of this type should prove useful in safeguarding industrial equipment from severe explosion damage. The experiments disclosed that the venting capacities of the diaphragms are approximately inversely proportional to their static bursting strengths."

Jan 1, 1950

By H. P. LeVan

Research was conducted to examine the feasibility of extracting manganese from Georgia umber ore by a three-stage continuous sulfuric acid-ferrous sulfate pickle liquor leaching process. A continuous cyclic process for treating the umber was operated successfully, using a synthetic solution simulating a ferrous sulfate fortified anolyte solution discharged from a manganese electrolytic cell as the leaching medium. Leaching efficiency based on removal of the manganese from the ore ranged from 83 to 89 percent for all systems tested.

Jan 1, 1965

By L. E. Green

For shortwall mining to be profitable, the additional capital investment of about $1 million for shortwall roof supports must be offset by decreased total operating costs and/or increased coal production. The Bureau of Mines therefore conducted a demonstration project to compare shortwall and room-and-pillar mining. Daily two-shift production from the bureau of Mines-Beth-Elkhorn Corp. shortwall demonstration n project averaged 975 tons of raw coal, compared with 905 tons from a room-and-pillar unit operating undo r similar conditions. The estimated direct operating costs for the shortwall and room-and-pillar unite were $4.21 and $4.03 pier ton, respectively. The profitability of the shortwall system was found to depend not only on the increased depreciation cost of the powered roof supports and the decreased cost of supplies and materials but also on such factors as the fixed and variable indirect costs and the selling price of the coal. Shortwall mining was demonstrated to be a viable alternative to room-and-pillar mining.

Jan 1, 1977

By Ann Hubbs, Vincent Castranova, Jane Y. C. Ma, De-Hwa Chao, Joseph K. H. Ma

AN OVERVIEW OF THE ACTION OF TETRANDRINE ON SILICOSISBecause of the persistent presence of silica dust in the lungs silicosis is a progressive and irreversible disease. At present, there is no proven effective therapy for silicosis. Limited choices of therapeutic intervention with corticosteroids and other immunosuppressive regimens 1,2 have been accepted for some forms of pulmonary fibrosis. These treatments are only minimally effective, and the results provide little understanding of the disease state due to the lack of correlation between drug activity and the mechanism of fibrosis. Thus, continuing effort must be made in the search for effective antifibrotic agents, which may be used to provide a sequential analysis of the fibrotic process and to open the door for further research and clinical development. Tetrandrine is one of hundreds of drugs screened for antifibrotic activity by Chinese scientists. It has been used in China as a treatment for silicosis in open clinical trials3 and in laboratory animals. The action of tetrandrine on pulmonary fibrosis has been attributed to its ability to inhibit particle stimulation of alveolar macrophages, a key cell type central to the fibrotic process, to release oxygen radicals and inflammatory cytokines. Alveolar macrophages (AM) residing on the alveolar wall, are the predominant phagocytic cells of the lungs responsible for pulmonary defense against inhaled microorganisms and other particles and thus play an important role in maintaining the homeostasis of the lungs. 7 Ample evidence suggests that cells of the monocyte-macrophage series play an important role in the immunopathogenesis of pulmonary fibrosis. When upregulated by silica, alveolar macrophages generate reactive oxygen metabolites8·9 which can damage lung parenchyma and release fibrogenic growth factors and cytokines, 10,11 such as interleukin 1 (IL-1), which can induce fibroblast proliferation and collagen synthesis. The cytokine-mediated fibroblast proliferation and collagen synthesis are key steps in the development and progression of pulmonary fibrosis .11 Previous studies by our group have shown that tetrandrine exhibits strong binding affinity to AM and inhibits particle-stimulated respiratory burst activity (oxygen consumption, superoxide anion release, and hydrogen peroxide secretion) in these cells. 13 In addition, studies by Kang et al. 14 have reported that tetrandrine inhibits silica-induced release of fibrogenic factors such as IL-1 which are capable of inducing fibroblast proliferation and collagen synthesis. Reist et al. 15 further suggested that the antifibrotic action of tetrandrine may be mediated in part by the direct effect of this drug on the ability of fibroblasts to respond to proliferative agents. These results indicate that the mechanism of silicosis involves activation of AM and fibroblasts by silica, resulting in abnormal collagen production due to miscommunications between the cell types. Tetrandrine may interrupt this process by direct interaction with the lung cells.

Jan 1, 1998

By H. W. Davis, W. W. Adams, O. E. Kiessling

"Current economic problems frequently have focused attention upon the lack of adequate quantitative information indicating the relationship between human effort and output in various branches of the mineral industry. With the exception of complete records covering coal mining, only scattered information on the units of human energy required to produce a unit of raw material is available for most of the important industrial minerals. Fortunately a virtually complete statistical record is available covering this phase of the iron-ore mining industry.For many years iron-ore mining companies, whose interest in safety work is well-known, have reported annual data on employment to be used in the compilation of accident statistics. These data on hours of labor and other detailed employment information have been correlated with the statistics on production also reported annually by producers. The outstanding trends shown by this composite record for the 10-year period 1923-32 are included in the following discussion, supplemented by a summary table that presents the principal statistical background of the study. 5The substantial reduction in the number of men needed to produce the annual iron-ore requirements of the United States, as shown strikingly in the graphs, illustrates that in iron-ore production improvements in technology have been consistently winning a battle over the difficulties of nature. In 1923, for example, 41,294 men working 107,551,244 hours were required to produce 69,351,442 gross tons of merchantable ore, equivalent to an average output of 0.645 ton per man-hour. In 1929, however, only 30,763 men working 77,111,686 hours 'zero required to produce 73,027,720 tons of merchantable ore, equivalent to an average output of 0.947 ton per man-hour. Thus, from 1923 to 1929 the average number of men working decreased 25.5 percent and the total man-hours worked 28.3 percent, while the average output per man-hour increased 46.8 percent and total merchantable ore production 5.3 percent."

Feb 1, 1935

By W. F. Netzeband

This paper, which describes mining methods and practices at the Rialto zinc-lead mine American Zinc, Lead & Smelting Co., in northeastern Oklahoma, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States, The Rialto mine is in the SE1/4 SW1/4 sec. 20 and the NW1/4 sec. 29, T. 29 N., R. 23 E., Ottawa County, Okla. (fig. 1). The 200-acre property is southwest of and adjacent to the town of Picher in the central part of the Picher field of the Tri-State zinc-lead mining district (fig. 2). Other mines of the company adjoin the Rialto on the east and south. Zinc-lead ores have been mined almost continuously from the Rialto tract since 1916. The property was acquired by American Zinc, Lead & Smelting Co. late in 1951, and the mine was operated thereafter by the Nellie B Division of that company until the end of 1955, when it was subleased to the Residue Mining Co.

Jan 1, 1958

By Thomas C. Denton

The Old Reliable copper mine was first examined by Harlow D. Phelps , an engineer of the Bureau of Mines , in October and November 1942 , in compliance with a request from the War Production Board , which furnished copies of assay maps of the 100- and 200-foot levels and requested that they be check-sampled . The author and R. li. Grantham and W. D. Hughes , engineers of the Bureau , made a second and more detailed examination later , after a number of manways had been opened that were inaccessible when the first examination was made .

Feb 1, 1947

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jun 1, 1997

By R. M. Gammell, S. H. Lorain

The Anderson prospect is one of a number of properties investigated by the Bureau of Mines during the course of preliminary studies of the lead-zinc districts of northern Stevens County, Washington. examined by W. R. Green, an engineer of the Bureau of Mines, in June 1944. This examination was supplemented in late 1944 and the spring of 1945 by pre- The property was first liminary angle-dozer trenching and core-drilling. A second examination of the property was made by the junior author in November 1945. The data obtained in the course of these studies is presented in the following report.

Mar 1, 1947

By Lee M. Manna

This report summarizes the program to design, fabricate, install and preliminary test a pneumatic braking system for 10-ton mine haulage cars. Major arrangement drawings are reproduced, pneumatic schematics, parts list and actual developed costs. Recommendations as to system improvements are made.

Jan 1, 1977

By F. S. Wartman

Recent changes in metallurgical practice, particularly those in flotation, have altered greatly the functions of the different units of a copper smelter. Gangue minerals are removed from the feed so much more thoroughly that the reverberatory furnace, once virtually a concentrator in which a low-grade ore was concentrated into a rich matte by virtue of the removal of gangue elements as slag, has become very largely a melting furnace in which the rich flotation concentrates are rendered molten so that they may be converted. Moreover, since the proportion of matte to slag in the reverberatory furnace output is greater than it was formerly, the amount of converter slag returned to the reverberatory for cleaning is, in comparison to the amount of slag actually formed in that furnace, also much larger. In some cases, approximately half of the reverberatory dump slag may have originated in the converter. The increase in the proportion of convertor slag to total slag produced has brought about certain consequences not entirely desirable. Converter slags contain a high percentage of iron and therefore are high in specific gravity and are very basic. A considerable guantity of magnetite, both dissolved and suspended as solid crystals, is always a component, The basic nature of the ordinary converter slag and the presence of the suspended magnetite crystals make impossible the reduction of the copper content of the slag below approximately 1 per cent by even the most prelonged settling, and a re-treating process is necessary. At present, general practice in western copper smelters is to return the converter slag molten to the reverberatory furnace. Here dilution by mixing, with slag formed in the reverberatory furnace and reaction with raw sulphides and siliceous materials in the reverberatory feed reduce the magnetite and increase the silicates to the point necessary for a satisfactory dump slag.

Jan 1, 1930

By Michael S. Miller

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied the 34,050-acre Cow Creek Wilderness Study Area (WSA) in order to evaluate its mineral resources. The WSA, located about 60 miles southeast of Havre, MT, contains sandstones, shales, clays, and coal of Cretaceous age. The Cretaceous rocks have been intruded by ultramafic diatremes. Quaternary glacial, stream, and landslide deposits overlie the older rocks. Claims are staked at five of seven sites favorable for diamonds within the WSA and at additional sites nearby. Although the ultramafic diatremes within and near the WSA contain minerals that are indicators for diamonds, no positive evidence of diamonds was found during this study. An abandoned coal mine, the Shellenberger, is inside the southwest boundary of the WSA. Possible petroleum and natural gas at depth are currently of interest; land within the WSA is leased or under lease application for oil and gas. The WSA contains subeconomic clays, zeolites, gold, silver, platinum group metals, and coal.

Jan 1, 1986

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jan 1, 1997

The Department of Interior, U.S. Bureau of Mines performs the task of estimating the quantity of coal reserves existing in each state on a county by county basis. As a part of Information Circular 8655, the Bureau of Mines established the criteria for the uniform estimations of coal reserves and listed the most recent estimates of coal reserves by county and by seam. At the same time however, the Bureau recognized that these figures represented the upper bound with regard to the estimated actually usable or obtainable reserves. Recovery of these reserves are subject to the mining methods used and to the resolution of such problems as the use of poor quality coal and competition provided by conflicting land use. These problems, in practice restrict the recovery of the estimated quantities of coal reserves listed in IC 8655. Another impact, the subject of this manual, is the impact resulting from previous mining activities. In particular, many of the reserve seams included in the reserve estimates overlie or underlie mined-out coal beds. Portions of these reserve seams may therefore be unmineable or at best may have a reduced quantity of extractable coal. In order to improve the accuracy of the coal reserve base estimates, the Bureau of Mines funded an effort1 to develop a systematic methodology for estimating the coal loss associated with the impact of previous mining activity. The coal loss calculation model (CLCM) described in this manual is a result of that effort and addresses the percentage of coal loss in reserve seams due to previous overmining or undermining.

Jan 1, 1976

By John C. Cook

Channel sand bodies ("wants" or "cutouts") are deposits of barren, hard sediments which interrupt production and pose safety hazards when encountered in underground coal mining. To locate these costly impediments to mining in advance, from the surface of the ground, the seismic reflection method is recommended. High-resolution (high frequency) techniques for shallow seismic exploration of coal beds have been worked out and are reported here, including a field example. Newly-developed high-frequency, digital recording equipment was used, together with light-weight shot-drilling equipment and a variety of down-hole seismic impulse sources. Techniques for rapid but complete coverage of a coal prospect area with a crew of 2 to 6 men n 2 or 3 vehicles are described in detail.

Jan 1, 1976

By A. B. Campbell

The Bureau of Mines is developing alloys using ion implantation as an alternative to bulk alloys that consume large quantities of strategic materials such as chromium and nickel. These alloys are formed at the outer layer of relatively common materials. To more fully understand the corrosion characteristics and physical properties of this outer layer, it was necessary to deter-mine the alloy concentration as a function of depth into the substrate material. Also, since many of the ion-implanted alloys would be utilized at elevated temperatures, it was necessary to determine the diffusion behavior of the implanted element. Proton-induced X-ray emission and inert gas ion sputtering have been utilized to generate composition depth profiles for Fe-Cr, Fe-Ni, and Fe-AI ion implanted alloys fabricated by implanting 25-kev Cr+, Ni+, or AI+ into iron substrates. The data were fitted (utilizing a computer program) with symmetrical Gaussian profiles yielding values for the range and range straggle of the ions. These parameters were then compared with those calculated from theory. Changes in the profiles due to annealing were investigated and values for the diffusion coefficient were obtained assuming diffusion according to Fick's Law. For the Cr+ and Ni+ implantation, the profiles as-implanted agree reason-ably well with theory and exhibit ?norrmal" diffusion characteristics at 500° C. For the Al+ implantation, the profile as-implanted is much broader than predicted and exhibits substantial enhanced diffusion at temperatures up to 500° C.

Jan 1, 1979