Search Documents

By E. M. Tignor

As a part of the program of promoting the conservation and efficient utilization of petroleum, studies are being made by engineers of the Bureau of Mines on secondary oil-recovery projects throughout the United States. In furthering that aim, engineering data concerning the reservoirs, methods of stimulating the production of oil, and other pertinent facts are collected, studied, and subsequently published so that others may profit by the experience gained. This report presents the results of a study made by engineers of the Franklin, Pa., office of the Bureau of Mines of secondary oil-recovery operations in the Boggs field, Spencer district, Roane County, W. Va., whore natural gas is injected into the reservoir to stimulate the production of oil from a so-called stripper field. The Boggs field, like most others in the Appalachian region, is one in which the major part of the natural energy that caused oil to flow through the reservoir to the producing wells during the primary stage of oil production has been dissipated. For all practical purposes, most of the oil produced in the Appalachian region at the present time can be considered to be from stripper fields. Consequently, secondary recovery methods are being used extensively in the oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering some of the oil that was not produced by primary production methods.

Jan 1, 1949

By G. B. Shea

In the search for possible future sources of petroleum products, the recovery and utilization of bitumens from the large outcropping deposits of bituminous sandstones in the United States have been under study by the Bureau of Mines for the past several years. The results of laboratory research in the adaptation of the hot-water separation process to recovery of bitumen from bituminous sandstones were reported in an earlier publication, on the Edna deposits near San Luis Obispo, Calif. This publication included analytical data on the cracked products and asphalts obtained from the extracted bitumen and on the cracking and distillation of the bitumen. Comparable hot-water separation tests have been run in the San Francisco, Calif., laboratory of the Bureau of Mines on quarry samples from the large deposits of bituminous sandstones near Vernal and Sunnyside, Utah. The bitumens were isolated from the extracts of the separation plant and analyzed at the Petroleum and Oil-Shale Experiment Station of the Bureau of Mines, Laramie, Wyo. Part I of this report summarizes the general characteristics of the Vernal and Sunnyside deposits and discusses the hot-water separation process as applied to those bituminous sandstones and the results obtained. The separation tests showed that these bituminous sandstones also respond to treatment by the hotwater method of separation. The bitumen in the Vernal sandstone was extracted more readily by the action of hot water than was the Edna bitumen, which greatly simplified plant operation. The Vernal sandstone contains no water-soluble iron compounds, such as were found in the Edna sandstone, and, therefore, required no preliminary water washing. Recovery of bitumen from the Vernal sandstone was about 96 percent.

Jan 1, 1952

By George S. Koch

A mathematical simulation model has been devised to guide the layout of underground mine workings, drill stations, and drill holes that are established in order to search for tabular ore bodies. Developed and tested for elliptical ore shoots in fissure veins in the Galena mine, Coeur d'Alene district, Idaho, the model can also be applied to ore bodies contained within sedimentary beds (for instance, many types of uranium, copper, and gold ore bodies) or other tabular structures. Programed for a time-shared digital computer, the model contains both stochastic and deterministic variables. Stochastic or natural variables include the number of ore shoots and their sizes, orientations, locations, and values. Deterministic or controllable variables include (1) locations and costs of workings; (2) drill-station locations and costs; and (3) drill hole azimuths, inclinations, lengths, and deflections, if any. For various assumptions about the stochastic variables, the model is run while the controllable variables are changed deliberately. Thus, layouts are devised to determine the percentages of the total number of assumed ore shoots found at different costs. In order to choose among the various layouts, cost-effectiveness measures are calculated.

Jan 1, 1974

By F. P. Haver

Because of increasing concern with air pollution, the Bureau of Mines has developed a hydrometallurgical procedure to obtain elemental sulfur from chalcopyrite (CuFeS2) by means of the following reaction: CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S. Under optimum conditions, 99.6 percent of the copper and 71.6 percent of the iron were extracted in 2 hours from a typical mill concentrate containing 75 percent CuFeS2 and 15 percent pyrite (FeS2). At the same time, 68.2 percent of the sulfur in the concentrate was oxidized to the elemental form. The leach was highly selective; gangue minerals, including pyrite, were not attacked, thus accounting for the relatively low recoveries of iron and sulfur. To obtain these results, the concentrate was ground to 98.9 percent minus 325 mesh, and 300 grams was treated with 1 liter of boiling ferric chloride (FeCl3) solution. The FeC13/CuFeS2 ratio was 2.7. Cement copper containing 99.9 percent copper was recovered from the leach solution by cementation on sponge iron. Excess iron, dissolved during leaching and cementation, was removed from the stripped solution by crystallization. Ferrous chloride (FeCl2?4H2O), obtained as a byproduct, was converted to high-purity ferric oxide (Fe203) and HCI by an oxidizing roast. The hydrochloric acid was then electrolyzed to obtain chlorine, which was used to regenerate the leach solution. The leach residue, which contained ~50 weight-percent elemental sulfur, was treated with an organic solvent to recover the sulfur and cyanided to reclaim gold and silver.

Jan 1, 1971

By Leonard F. Heising

At the Groveland mine iron ore is mined by open-pit methods and concentrated by means of spirals and flotation. A brief history of the mine and its early development is given. The ore deposit is described, with emphasis on those physical characteristics that affect the choice of mining and milling methods. Development and mining, which include breaking ground, loading, transportation, engineering, and operating control, are explained, and the milling method is described Mining and milling costs are given in percent of total cost.

Jan 1, 1963

By H. B. Brunot

A complete list of permissible mine equipment , tested and approved by the Bureau of Mines previous to January 1 , 1947 , was published as Information Circular 7432.27 A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 was published as Information Circular 7465.3/ The present list supplements Information Circular 7432 and includes all of the equipment approved during the calendar years 1947 , 1948 , and 1949. It therefore supersedes Information Circular 7465. The list also includes an appendix ( No. 2 ) giving the symbol that must be used by every cable manufacturer in marking trailing cables that have passed the test for flame resistance as stated in the amendment of October 21 , 1947 , to Schedule 2E . The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification . Thus , Information Circular 7432 showed six air compressors on the active list ; five additional compressors , Nos . 7 to 11 , inclusive , in this category were approved during 1947 , 1948 , and 1949 . Several items that were listed in Information Circular 7432 have been repeated in this circular where it was necessary to show that approvals of such equipment were extended to cover an additional voltage rating or other changes . Equipment listed in these circulars is approved by the Bureau of Mines only when found , upon inspection and test , to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal -mining industry . The use of such equipment in mines known to be gassy , as well as in those that may become so , is earnestly recommended in the interest of safety . This circular is published so that the industry may be kept informed as to the many types of machines , devices , and lamps that are available for reducing explosion and other hazards incident to coal mining . This circular and Information Circular 7432 give the complete list of permissible mine equipment that is available under the various classifications .

May 1, 1950

By John R. Reeves

The data presented in this paper form the chief part of a general survey of the oil-shale resources of Indiana. Other papers* have already been published which contain data an various aspects of this resource. In combination, these papers present data with reference to the following points; (1) distribution of the New Albany shale; (2) amount of shale available; (3) homogeneity and thickness of the formation; (4) amount and quality of the oil obtained from the shale; (5) nitrogen content of the shale; (6) extractibility of the shale and its amenity to breaking; (7) some economic factors bearing upon the utilization of the shale; and (3) other miscellaneous factors and data. In the future, technical work on other phases of the general problem is expected to be done with the object of making a complete survey of this resource which is of much potential importance to the state and nation.

Jan 1, 1923

By Robert K. Koch, Henry E. Blake

Laboratory tests were made to determine if aluminum fluoride of commercial grade could be synthesized by reacting alumina hydrate with dilute ( 25 to 75 grams per liter of fluorine ) aqueous fluoride solutions . • Products containing up to 90 percent aluminum fluoride ( A1F ) were synthesized by reaction of alumina trihydrate ( A120 3H2O) with either dilute hydrofluoric acid ( HF ) or ammonium fluoride ( NHF) solutions , the ammonium fluoride solution resulting from ammonia ( NH ) desilication of a hydrofluoricfluosilicic acid ( HF - H₂ SiF ) solution . Fluorine recoveries of over 80 percent were obtained with either type of solution . The hydrated precipitates of AlF, and ( NH4 ) , A1F ( ammonium aluminum fluoride ) obtained by reacting hydrated alumina with these solutions were subsequently converted to anhydrous AlF, by controlled heating .

Jan 1, 1964

By David A. Lipton

In the summer of 1985, at the request of the U.S. Forest Service, the U.5. Bureau of Mines examined the 109,000-acre West Big Hole study area to evaluate its identified mineral resources. The study area is in Beaverhead County, about 50 mi west of Dillon, MT. Four lode properties within or adjacent to the study area contain an estimated 452,000 tons of identified subeconomic gold-silver resources. Resources ranged from 900 to 302,000 tons, with estimated grades between 0.02 and 0.23 oz/ton gold and as much as 4.8 oz/ton silver. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that exploration may identify resources on 18 additional lode properties within the study area and 5 properties adjacent to it.

Jan 1, 1988

By William O. Vanderburg

Some mines after passing through the prospecting stage and becoming sizable enterprises still adhere to the development program of the prospect, extending their workings without definite plans. In mining operations where definite structural conditions do not exist, a prearranged layout of mine development is not feasible; but where exploration and preliminary development have indicated the extent and probable limits within which the ore is expected, careful planning of development will result in a lowering of mining costs and a consequent increase is profits. A lack of definite plane for laying out mine workings is one of the contributory factors to unnecessarily high costs. Although this paper deals primarily with the influence of level spacing on mining costs, still other phases of mine development, such as the proper spacing of ore chutes and raises, can be analyzed on a cost basis in a similar manner, as shown herein. LEVEL SPACING The problem of establishing a new level or levels in order to exploit steeply dioping ore deposits and prospect the ground at depth recurs at intervals during the active life of mines. Driving levels is largely "dead work" and therefore costly. By the judicious selection of the proper level interval after balancing the opposing factors involved in the problem, a considerable saving in mining costs can be effected. Although much has been written in regard to the various methods employed in ore extraction, mining literature is still incomplete in regard to the factors-influencing level spacing at various mines. Level spacing involves procedures not lending themselves readily to description, and, moreover, it is a phase of mining operations that is apt to escape criticism, because only those in close contact with the operations are equipped with the necessary familiarity with the conditions to pass judgment.

Jan 1, 1932

By Mukund O. Gangal

A deep cutting continuous miner, HH456, was tested under production-mining conditions at the Joanne Mine, Rachel W. Va., for about 1 ½ years (226 production days). The miner was run in two modes: a low head-rpm, deep cutting and high rpm, shallow-cutting mode. These tests confirmed that deep cutting and slow cutter speed reduce respirable dust significantly under production mining conditions. Quantitative reductions in dust, in deep vs shallow cutting, were 73°; in return air and 63% at the operator's location. Production rate, (tons/shift), and bit consumption rate did not show any relationship to deep or shallow cutting. Reliability and maintainability of the miner were worse in deep cutting mode due to cutter drive shaft failures; the cutter shaft problem was solved through improved material and design. Excluding the cutter shaft repairs. maintainability war similar for deep and shallow cutting,

Jan 1, 1979

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Southern Experiment Station of the U.S. Bureau of Mines, cooperating with the University of Alabama and Alabama coal producers, has made a series of investigations of the washability of coal from commercially important bens of Alabama. The results of 13 investigations pertaining to the Mary Lee, Clark, Black Creek, Jefferson, Pratt, Corona, Carter Brookwood, Blue Creek, Thompson, and Woodstock beds have been published. 4/ This report, the fourteenth of the series, deals with run-of-mine coal from the Henry Ellen bed at the Acmar No. 5 mine of the Alabama Fuel & Iron Co.The Acmar mine is 1/2 mile west of Acmar, Saint Clair County, in the northern part of the Cahaba field. Present production at the mine is about 800 tons per day, all of which, accept the lump coal, is treated in jigs. The washability data were obtained by means of screen-sizing and float-and-sink tests. There are included, also, tests showing the extent of liberation of impurities by recrushing the coarser sizes of coal from the top bench and tests showing the flakiness in selected sizes.SAMPLING AT THE MINEThe Henry Ellen bed at Acmar consists of two benches separated by a shale parting. At the point of sampling the top bench was 6 feet 3 inches thick and contained a 1-inch and a 1 1/2-inch band of bone. The bottom bench was 5 feet thick and was separated from the top bench by 20 inches of shale. In taking the samples for the washability study the working face was squared up, and a representative 2-ton section was out from each bench. The shale parting was discarded, according to usual mining practice."

Nov 1, 1936

By R. L. Grant

The Bureau of Mines developed two new gap-sensitivity methods for explosives, and especially permissible explosives, to overcome certain disadvantages of the present routine half-cartridge method. The revised methods are based on the statistical up-and-down method and give more useful measurements of the 50-percent' gap values than the nonstatistical routine method. The new methods use full cartridges and incorporate certain physical improvements such as the use of cardboard tubes for containing the explosives and coal dust gaps to simulate actual mining conditions. A total of 60 samples of permissible explosives were evaluated simultaneously with the 2 improved methods and with the half-cartridge method

Jan 1, 1967

By M. D. Aldridge

The results of a four-year research effort aimed at developing a practical and effective electronic system for monitoring safety conditions throughout a coal mine by displaying, at a central location, remotely measured parameters are described. This document presents the general philosophy of an experimental system in an operating coal mine. The conclusions drawn from this experience are presented and a typical design for a large coal mine is described.

Jan 1, 1974

By L. T. MCELVENNY, Robert B. McElwaine, M. Clair Smith

Production of mercury from the cinnabar deposits of the southwestern Arkansas mercury district began in 1931 , reached its peak in 1942 , and ended in 1944. The mines are now idle . Virtually all the cinnabar was obtained from deposits in a belt , about a mile wide , of steeply dipping sandstone beds in the overriding blocks of three thrust faults . The belt was productive for a length of about 27 miles eastward from eastern Howard County, through Pike County, into Clark County . During the early life of the district, Federal agencies watched and recorded its progress as a contributor of a strategic metal, and later, during the war, conducted investigations designed to advance its development . In 1941 , the Bureau of Mines and the U. S. Geological Survey cooperated in investigations on eight mineralized areas in the western part of the district , to wit : Hales mine , U. S. mine , Lulu Bell property, Hopkins Hill , East Gap Ridge , Gap Ridge , Parnell Hill , and Section 17 mine area . U. S. Geological Survey prepared both surface and mine maps and designated the areas to be investigated ; the Bureau did the drilling , trenching, and sampling involved in the investigations . Twelve holes , aggregating 3,539 feet of bore , were diamond drilled on six properties ; 5,309 linear feet of surface trenches were bulldozed in six areas and 19 samples taken from them ; and 86 underground channel samples were cut in two adits on one property . In 1944 , the Bureau of Mines measured mine dumps and calcine dumps in the district in an investigation of their mercury content . Two mine dumps and one calcine dump were sampled . The data pertinent to the work done by the Bureau are included in this report .

Oct 1, 1950

By George Saliba

This report disucsses the formulation of a mathematical model for the steering of a conveyor belt by a flat return idler and a troughed idler under various loading conditions. Significant parameters associated with belt training are identified. The generation of a skewed flat return idler model in terms of a steering force and self-aligning torque is presented. Development of the mathematical model for the flat return steering idler is illustrated for the case of no circumferential slip occurring and for the assumption of a bidirectional slip mechanism. Experimental results supporting the theoretical analysis is presented.

Jan 1, 1977

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By John W. Cole

The Butte district has been the principal producer of metallurgical-grade manganese in the United States since World War I. Manganese dioxide nodules are produced from rhodochrosite ore by concentrating the rhodochrosite and roasting the concentrate in rotary "cement-type" kilns. The Anaconda Copper Mining Co. is the only producer at present. Under the stimulus of a purchasing program administered by Metals Reserve Company during World War II, however, several independently owned or operated mines (including the Norwich) produced manganese carbonate ore. These mines were examined in Juno 1949 by John W. Taber, mining engineer, Bureau of Mines. A core-drilling program to develop ore in the Norwich mine was recommended and approved. drilling was completed early in 1950. This report gives factual data obtained.

Jan 1, 1951

By J. N. Greaves

Investigations were conducted by the U.S. Bureau of Mines to develop flowsheets for the recovery of tungsten and gold from four Alaskan scheelite-bearing ores. Basic gravity concentration and cyanide leach tests were performed on all samples. About 46 pct of the tungsten and 30 pct of the gold from one sample were recovered in a gravity concentrate containing 24 pet W03 (tungstic oxide) and 119 troy ounces per short ton (tr oz/st) Au. Froth flotation of the gravity concentrate resulted in separate tungsten and gold products with grades of 38 pct W03 and 2,720 tr oz/st Au and recoveries of 60 and 97 pet, respectively. Additional gold was recovered from the gravity and flotation tailings by cyanidation. Overall recoveries of tungsten and gold from this sample were 28 and 94 pet, respeetively. A flowsheet with mill design parameters was developed that consisted of (1) free gold and scheelite recovery by gravity methods and froth flotation and (2) fme-grained gold recovery by cyanide leaching of reground gravity and flotation tailings, followed by a carbon-in-pulp (CIP) circuit. Data were developed from the Bond mill work index, gold and tungsten flotation, conventional and high-rate thickening, cyanide leaching, and CIP adsorption tests.

Jan 1, 1989

No noticeable international economic recovery occurred during the first half of 1982. Industrial production continued to fall in the United States, Canada and Italy and to hold steady in France. Modest increases in production occurred in Japan, England and Germany, although some decline took place from March to April. The U.S. mining industry has been more severely affected by the world recession than the U.S. economy. This is not immediately obvious when comparing the U.S. mining industrial production index from 1981 to 1982, which decreased 8.5 percent, as compared to a 7.1 percent decline for total domestic industries. However, "mining" industry statistics in the U.S. national economic accounting system include petroleum and natural gas as well as minerals. When metal mining is isolated, the decrease in production from 1981 to 1982 is 19.3 percent. If metal mining production continues to perform at the same rate during the third and fourth quarters of 1982 as during the first half of the year, declines from 1981 levels will be quite severe. Aluminum will have declined 22 percent, copper 18 percent, iron ore 24 percent, lead 3 percent, steel 29 percent, titanium 2 percent and zinc 25 percent.

Jan 1, 1982