Search Documents

Maps To Accompany Bulletin 494

Jan 1, 1950

By Stanton L. Tainter

"As an adjunct to its minerals-investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the supervision of J. H. Hedges, chief, Tucson Branch Mining Division, and under the general supervision of Lowell B. Moon, chief, Mining Division, reports upon certain methods devised to overcome difficulties encountered in cementing of diamond-drill holes at a Bureau of Mines project at Christmas, Gila County, Ariz.Pressure grouting was employed to recondition a caved hole it was desired to reopen and deepen. The hole, which had boon stopped 7 months previously at a depth of 488 feet, was caved below 449 feet in a contact zone of claylike, altered diorite and crumbly metamorphosed limestone. As other means of obtaining moderate pressure were not available, carbon dioxide gas, drawn from tank of liquid carbon dioxide through a pressure reducing and regulating valve, was used. The hole was reopened successfully with 12 grouting jobs.Another hole, where cawing from several water-bearing fractures between 202 and 232 feet gave trouble, was successfully cemented by the use of a grouting plug. An attempt to cement through the rods had failed, owing probably to agitation caused by water currents. Pressure grouting through the caning set above the cave could not be need, because water was forced up outside the casing when pressure was applied. The problem was solved by using a wooden plug 1-13/16 inches in diameter, which, when soaked in water, expanded to a tight fit in an AX hole. A hole was drilled through the plug, and a rubber flap valve was nailed to the lower end. In the upper end of the plug the hole was enlarged to fit loosely over an EX rod coupling finished smooth. The plug was lowered on the end of the drill rods to a point about 10 feet above the cave, where it was allowed to expand tightly to the hole. Cement grout was then pumped through the rods, and the rods were removed from the hole. After allowing time for the cement to set, the wooden plug was chopped out and drilling van resumed.Over 300 tests were made to determine the type of cement most suitable for use on the Christmas job, and the effect of cement-water ratio, temperature, and various admixtures on workability, setting time, and strength. The results of these tests, described in detail in the body of this report, indicate the desirability of thoroughly testing available cements when it is necessary to drill holes under difficult conditions that may cause failure.When it became desirable to reopen and deepen a caved drill hole, it was considered easiest to recondition the hole by pressure grouting, As other mans for obtaining moderate pressure were not available, a method utilizing carbon dioxide gas was employed. The hole was reconditioned successfully with 12 grouting jobs."

Nov 1, 1949

By Seth T. Reese

THE INJURY DATA and experience at coal mines in the United States for 1951 are presented in this bulletin under the following general heads: (A) General injury experience: Tables 1 to 18: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major and detailed injury agencies, and distribution of injuries by part of body and days of disability. (B) Selected injury data: Tables 19 to 43: Contain current data on various selected factors of operating and physical conditions that contributed to the occurrence of injuries at bituminous-coal, lignite, and anthracite mines. These factors include extent of hand and machine loading, size of mine by employment and production groups, thickness of bed or vein, duration and number of work shifts, rating of mine as gassy or nongassy, types of cap lamps, explosives, and combination of factors that influence mine safety. (C) Injury experience by States: Tables 44 to 50: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major causes and principal agencies, injury records of all coal-producing States, and the relative standing by States according to injury-frequency rates. (D) Major disasters: Table 51: Lists the coal-mine disasters that occurred during 1951, giving location, source, and cause. A major disaster in coal mining is defined as a single accident in which or as a result of which five or more men lost their lives. (E) Historical coal-mine injury experience: Tables 52 to 86: Contain data on injuries, injury-frequency rates, employment, and production at bituminous-coal, lignite, and anthracite mines from the earliest records through 1951.

Jan 1, 1955

By W. W. Adams

"During the calendar year 1925 the Bureau of Mines received from the operators of several hundred mines and quarries complete accident records covering deaths, permanent disabilities, and “lost time” temporary injuries. Some of the companies, - those that participated in the National Safety Competition-also furnished information showing the number of man-hours of work performed during the year. With these two types of information it was possible to calculate the accident-frequency and accident-severity rates of the different plants. Complete and comparable reports of accidents and Man-hours of “exposure” were received from 34 underground metal mines, 59 underground coal mines, 15 underground mines producing other nonmetallic minerals, and 102 open quarries or open-pit mines. The figures in the table appended to this report show the accident severity rates and other data for each of the 34 underground metal mines and for the group as a whole. It is proposed to publish similar figures for the other classes of mines and quarries at an early date.The 34 metal mines listed in the table are situated in Arizona, Idaho, Kansas, Michigan, Minnesota, Missouri, New Jersey, New Mexico, Oklahoma, South Dakota., and Utah; they employed 5, 925 men, an average of 174 men per mine, including employees above-ground as well as underground. With but few exceptions, 50 men was the minimum number of employees in any mine. The total period of employment or “exposure” at the 34 mines was 14,612,607 man-hours, an average of 2,466 hours per man, or the equivalent of 308 work-days of eight hours for each employee. Accidents resulted in 15 fatalities, 9 permanent disabilities, and 1,950 temporary “lost time” injuries (causing disability exceeding remainder of shift). The fatal and nonfatal injuries represented 132,575 days of disability. Thus the accident frequency rate for the group was 135 accidents per million hours and the accident severity rate was 9.073 days lost per thousand hours of 1 “exposure”. The severity rates ranged from 0.227 to 88.653, while the ·range of the accident-frequency rates was from 16. 6 to 307 .4. In compiling the accident severity rates shown in the table, all accidents caused by explosives were weighted at twice the number of days actually lost, as one of the purposes of the National Safety Competition was to stress the prevention of accidents caused by explosives."

Sep 1, 1926

By Paul M. Tyler

Graphite occurs in many places in the United States, but previous to 1914 the domestic production amounted to only 15 to 20 per cent of the natural graphite consumed in this country. Including artificial, graphite, the proportion was about 25 per cent. During the World War the production of both natural and artificial graphite increased until, in 1918 it, contributed more than one-half of the available supply, and since 1919 the proportion has not fallen below 40 per cent. Except during the war period, however, this apparently increasing independence has not been due to any large increase in production from domestic mines. It simply reflects a larger output of artificial graphite and reduced imports of Ceylon lung and chip, grades which have never been produced in substantial quantity in the United States. DOMESTIC DEPOSITS3 American graphite deposits, though numerous and often large, are characteristically low-grade. They constitute an abundant source of potential supply, but in normal times they have proved relatively costly to work, and even at the same price the various products have never been able wholly to displace certain imported qualities, notably crucible grades from Ceylon and pencil graphite from Mexico.

Jan 1, 1929

By J. T. McCartney

The Bureau of Mines has developed an automated reflectance scanning microscope system, primarily for determination of volume proportions, size distribution, and mode of association of the physical (petrographic) components of coals. The process, which is potentially more rapid and objective and less tedious than a visual microscopic procedure, involves magnetic tape recording of several millions of reflectance readings on micro-meter sized areas of polished coal surface and computer analysis and interpretation of some characteristics of the coal components. The system was tested in a study of pyrite distribution in steam coals. The application was essentially successful, but defects in polished pyrite surface characteristics and problems in adequate sampling prevented completely satisfactory results. Pyrite con-tent and coal-pyrite particle association could be determined nearly as well as by visual microscopy, but size distribution data were less acceptable.

Jan 1, 1969

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

By Federick W. Miller

The Bureau of Mines has investigated the availability of columbium from 19 deposits (3 producers and 16 nonproducers) in 7 market economy countries (MEC?s). Brazil has the largest recoverable columbium resource, posessing approximately 2.39 million metric tons Wmt), or 69 pet of the MEC total (3.47 Mmt). The Western Hemisphere countries of Brazil, Canada and the United States contain 3.14 Mrnt of recoverable columbium or 90 pnt of the MEC total. Columbium recovered as a byproduct of tin mining is not included as part of MEC resources in this study. Currently producing mines are Araxa and Catalao in Brazil, and Niobec in Canada, These three mines have 2.42 Mmt of recoverable resources or approximately 69 pct of the MEC total. It is estimated that these mines, operating at full capacity, could satisfy cumulative MEC demand (based on an annual growth rate of 5.1 pct) for the next 20 yr. The United States is totally dependent upon foreign sources for its columbium supply. The majority of U.S. columbium is imported from Brazil in the form of steelmaking- grade ferrocolumbium. Canada has been the sole source of pyrochlore concentrates since Brazil discontinued exports in 1981. The United States also imports small (but important) quantities of columbium as columbite concentrates from Nigeria and Brazil, as columbite contained in tin slags from Thailand and Malaysia, and as synthetic concentrates from the Federal Republic of Germany.

Jan 1, 1986

By M. R. Geer

The Bureau of Mines surveyed the solid wastes that have accumulated from coal mining in Washington, Oregon, and Montana. Location, amount, character, and condition were determined, and both economic and environmental factors were considered. Areas covered by waste comprise 800 acres in Washington, 5 acres in Oregon, and 1,200 acres in Montana. In a few cases waste is being utilized, particularly cinder from burned refuse dumps, as fill in road construction and as a ceramic raw material. It is estimated that wastes deriving from coal mined for electric power generation by 1974 may amount to 3 million tons of washery refuse, 2.7 million tons of fly ash, and 1,000 acres of spoil banks.

Jan 1, 1969

By ALBERT LONG, Wing G. Agnew, FELIX CHAYES, Alton Gabriel, Leonard Obert

Although the technique of diamond drilling was developed nearly 80 years ago, the use of this process as an aid to mining and other fields of engineering has increased greatly during the last decade , primarily as a result of the development of the cast -set bit , which now largely replaces the hand - set types , and of the use of bort instead of carbons . Since this transition to cast - set bits and bort diamond , many papers ( 1-14 ) have been written on the application of diamond drilling to various engineering problems . These papers contain , besides specification of the problems , some information on the labor and bit costs and a few data on drilling technique . These data , however , are subject to restricted interpretation owing to the large number of variables , which are not controlled in field drilling . Only one paper has come to the attention of the authors , namely , that by Sundberg and Lindqvist ( 16) , which reported a study of diamond drilling under controlled conditions . This paper was written early in the transition period, and the data and conclusions presented therein have had , without a doubt, considerable influence on the development of presentday diamond bits and In view of the fact that during the last 10 years thrilling procedure . have been new developments in diamond bits. and new applications of diamond drilling , a general program of research has been inaugurated to study the problems resulting from these changes .

Mar 1, 1947

By Bruce McDonald

This report contains the Phase I findings of a study to select and test devices for preventing lack of alertness in haulage truck drivers. The extent of the problem was determined by visiting surface metal and nonmetal mines, interviewing drivers and safety personnel and reviewing accident reports. A number of devices for detecting a lack of alertness were considered and three were recommended for testing in actual operation.

Jan 1, 1977

By Charles D. Haynes

Outside air for ventilating coal mines in Alabama varies considerably in both temperature and moisture content during the year. Alternate condensation and evaporation of the moisture on mine roofs may result in stresses detrimental to the strength of mine roof. It is well known that the clays in shales absorb moisture, and many investigations have noted the weakening of shales by absorption of moisture. Parker (1970) concluded that there is an annual cycle of rock deterioration in mine roof rock caused by the annual temperature-humidity cycle at the surface. He further noted that moisture reduces the strength of dry rock by one-half, that moisture added to dry rock can cause failure in compression, and that drying of wet rock causes tensile stress buildups by shrinkage. His recommendations for alleviating the moisture-temperature problem was to seal the rock in critical areas and to control ventilation so that air temperature will be lower than rock temperature. The latter recommendation will avoid condensation on the rock surfaces. Hartmann and Greenwald (1941) published the results of a very comprehensive experimental project to determine the effect of temperature and humidity changes on the behavior of mine roof. Their general conclusions included statements that roof rocks were very sensitive to moisture changes, but had low coefficients of thermal expansion. The coefficients were twice in the direction normal to the bedding plane as compared to the parallel

Jan 1, 1975

By A. S. Peck

This report presents the results of a cooperative study between the Bureau of Mines and the University of Utah to define the mechanism involved in the adsorption of oleic acid and sodium oleate on fluorite, calcite, and barite, using an infrared spectrophotometer for identifying and measuring the adsorbed reagents and reaction products. Fluorite, calcite, and barite react with oleic acid and sodium oleate in a water system, forming chemisorbed and solution products. The chemisorbed species is a surface mineral cation-collector anion salt, Chemical analysis of solution resulting from the adsorption reaction indicates that the adsorption process causes displacement of mineral anions, namely, fluoride, carbon ate, and sulfate from the surface of these minerals.

Jan 1, 1963

By E. Morrice, R. D. Smith

Thermal expansion and electrical resistance measurements were made on cerium metal from 4° to 300° K. The apparatus developed , including a specimen holder and a cryostat system , are described along with the experimental techniques used in obtaining the measurements . The total linear thermal expansion Data at of 99.83 weight - percent cerium metal between 4 ° K and room temperature was 4.24 percent . The resistivity at 4° K was 7.0 x 10-6 ohm- centimeter . 4° K indicate a fundamental relationship between residual resistivity and purity of cerium metal . The effects of annealing and repeated thermal cycling on resistivity were determined .

Jan 1, 1964

By J. H. Rose

This paper describing the milling practice at the Magma Copper Co., Superior, Ariz., is one of a series being prepared by the Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to William Koerner, general manager of the Magma Copper Co., for permission to prepare this article; to J. S. Garrott, former mill superintendent, for the historical facts; and to Walter Cooksley, general foreman, for his assistance in obtaining the data.

Jan 1, 1930

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By S. J. Broderick

[The discovery in 1934 that carbonaceous materials, such as coal, peat, and lignite, when treated with concentrated sulfuric acid, were given cation or bate-exchange properties opened up a field of new materials with many interesting possibilities. These hydrogen exchangers, as they were called, were so superior to the impractical hydrogen exchangers made from natural and synthetic zeolites tat they were accepted immediately by the water-conditioning industry. A noteworthy advantage of the carbonaceous exchangers is that they are nonsiliceous, hence they do not give up silica to the water as do the natural and synthetic Zeolites, especially if the hard water is corrosive. For this reason the new exchangers found immediate favor in boiler-feed-water conditioning.]

Jan 1, 1941

By S. J. Broderick

[The discovery in 1934 that carbonaceous materials, such as coal, peat, and lignite, when treated with concentrated sulfuric acid, were given cation or bate-exchange properties opened up a field of new materials with many interesting possibilities. These hydrogen exchangers, as they were called, were so superior to the impractical hydrogen exchangers made from natural and synthetic zeolites tat they were accepted immediately by the water-conditioning industry. A noteworthy advantage of the carbonaceous exchangers is that they are nonsiliceous, hence they do not give up silica to the water as do the natural and synthetic zeolites, especially if the hard water is corrosive. For this reason the new exchangers found immediate favor in boiler-feed-water conditioning.]

Jan 1, 1941

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955