Search Documents

By David Schlain

The galvanic corrosion properties of titanium in contact with commercially pure aluminum, copper, or type 302 stainless steel in some of the common organic acids were investigated. Acids used in these experiments were 10 percent formic, acetic, lactic, citric; 1 percent oxalic and tartaric; and 9 percent oxalic. Electrode-potential measurements and several types of galvanic couple experiments were carried out. Solutions were aerated by three methods: Flow of air, flow of helium, and natural aeration. Work was done at 35° C. with couples consisting of equal areas of the 2 metals. Titanium was resistant to corrosion in most of the organic acids studied, whether alone or in contact with a dissimilar metal. However, titanium coupled with aluminum did corrode in 1- and 9-percent oxalic acid solutions. Contact with titanium usually caused aluminum to corrode by galvanic action. Copper was subject to galvanic attack in 10-percent acetic acid with a flow of air. Contact with aluminum to some solutions in which titanium is ordinarily inert and noble with respect to aluminum caused titanium to corrode

Jan 1, 1956

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By W. A. Selvig

"The purpose of the investigation described herein was to determine how closely different laboratories can check one another in making determinations of fusibility of coal ash with the De Graaf electric coal-ash fusion furnace: how well duplicate determinations by the same laboratory will check, and how the results with the De Graaf furnace compare with those of the standard gas-furnace method of the American Society for Testing Materials.4Thanks are due the following laboratories who cooperated in this study by making fusibility tests with the Do Graaf electric coal-ash fusion apparatus: J. J. Brennan, testing engineer, Northern States Power Co.; R. E. Gilmore, superintendent, Fuel Research Laboratories, Canadian Department of Mines A. T. Leavitt, president, and W. Mueller, chief chemist, Hamilton By-product Coke Ovens. Ltd.; Edgar Stansfield, chief chemical engineer, Scientific and Industrial Research Council of Alberta. Canada; and H. S. Vassar, laboratory engineer, Public Service Electric and Gas Co.The ash-fusibility determinations by the standard gas-furnace method were made in the Coal Analysis Laboratory of the Bureau of Mines at Pittsburgh under the direction of H. M. Cooper, associate chemist. The investigation was made at the suggestion of A. C. Fieldner, chief engineer, Experiment Stations Division of the Bureau of Mines.Routine determinations of the fusibility of coal ash are made in the laboratories of the United States Bureau of Mines by the gas-furnace method. This method was standardized after considerable experimentation5 on the nature of the fusion of coal ash and the various factors which affect its determination. The method was subsequently adopted by the American Society for Testing Materials as one of its standard tests."

Jun 1, 1930

By E. S. Leaver

Experiments dealing with the dissolution of silver by cyanide from various silver minerals were reported several yews ago.4/ This work showed that the silver in some silver minerals is completely and readily soluble in cyanide solution, whereas other silver minerals must be given special treatment before or during cyanidation to obtain much dissolution of the silver by cyanide. Flotation as a method for treating silver ores has not been studied much, except in the case of base-metal ores carrying silver, particularly lead-silver ores. However, many mills now are concentrating gold ores by flotation, and when such ores also contain silver the recovery of the silver by flotation is of considerable importance. Moreover, many mines contain ore in which silver is the principal valuable constituent. Some of these ores are amenable to cyanidation, but the cost of a cyanide plant may be prohibitive because of limited ore bodies or other factors. In such instances the successful application of flotation would mean that the property could be operated.

Jan 1, 1939

By Frank L. Hess

Vanadium, although widely spread in minute quantities through the crust of the earth, is found in few places sufficiently concentrated to be economically mined and prepared for use. Most rocks carry from a trace to a few hundredths of a per cent of vanadium oxide, and coal ash may carry about as much as the rocks, Much of the "coal" quoted in the literature as carrying vanadium has been asphaltite, and in other ccal the vanadium is of late introduction. The ash of the petroleums, though usually present in very small quantity, may carry a large percentage of vanadiun, so that production of vanadium from it has been seriously considered. Naturally the ashes of soze asphaltites similarly carry vanadium.' The great deposit at Minasragra, Peru, to which further reference will be made, is probably an altered asphaltite. Ilmenite and cther iron minerals usually carry vanadium 10 and some has been saved from the minette ores of France. 11 Many veins that carry lead copper and zinc minerals also carry a little vanadium, which, especially if the veins are in a comparatively dry region, such as the southwestern United States, northern Mexico, Northern Rhodesia, Southwest Africa, or Spain, collects in the oxidized parts of the veins as vanadinite,

Apr 1, 1932

By A. W. BELDEN

Among the investigations that the Bureau of Mines is conducting witha view to increasing efficiency in the utilization of fuels belonging to or for the use of the Government is an investigation of the processesthat take place in a foundry cupola during a melt. Some observations on the results of cupola tests of cokes at the Government fuel-testing plant in St. Louis, Mo., the coke being fromcoal from many coal fields of the United States, have been stated in a previous bulletin.s Especial attention was given to the meltinglosses that resulted from the use of different grades of coke, light and porous or heavy and dense. These losses amounted in one instance to 52.5 per cent of the iron charged and showed, in convincing manner, the need of exact information in regard to conditions in the fuelbed of the cupola.b Melting losses of iron have been fully appreciated but little under-- stood. The fact that these losses were possible with either light or heavy coke led to the belief that by using small charges 80 placed that. melting would take place in that zone of the cupola where the highest heat and the smallest percentage of oxygen prevailed and by confiningall melting to this zone these losses would be eliminated and the economical use of practically any coke produced for metallurgical purposes would become possible. This widening of the field from whichcoke might be drawn for foundry purposes would serve to place the foundryman in an independent position as regards his source of supply, and would tend to conserve the better grades of coking coals, which are being rapidly exhausted, by making the poorer grades available for mixing with them. In order to investigate conditions within a cupola, the Bureau of Mines as a first step decided to install a commercial cupola, to sample the gases during their travel from the tuy~res upward, and to determine the temperature of the fuel bed.

Jan 1, 1913

By Thomas A. Phillips

This publication is an economic evaluation of the Bureau of Mines electrolytic process for recovering lead from scrap lead-acid batteries. In this process, scrap batteries are crushed and separated into metal and sludge fractions. The metal fraction is cast as anodes and electro- refined. Lead in the sludge fraction is converted to lead carbonate by reaction with an ammonium carbonate-ammonium bisulfite solution. The lead carbonate is then dissolved in a fluosilicic acid electrolyte from which pure lead metal is electrowon. A cost estimate is presented for a plant capable of processing 10,000 scrap batteries per day. The fixed capital cost for this plant is estimated to he $14 million on a fourth quarter 1984 basis. Operating costs are estimated to be $0.15/lb Pb recovered. Assuming a lead selling price of $0.17/lb, the interest rate of return on investment after taxes is 11 pct. A lead selling price of about $0.21/lb is needed to obtain a 20-pct-interest rate of return.

Jan 1, 1986

By J. W. Griflith, P. A. Mack, C. M. Lang, S. Riling

"N-acetyl-beta(B)-D-glucosaminidase is a N-acetyl-beta((B)-D-glucosaminidase enzyme se¬creted by alveolar macrophages in response to phagocytosis of particulate material. Alveolar macrophages participate in the degradation and fibrosis of pulmonary tissue that results in pneumoconiosis. Known quantities of four characterized respirable dusts were bronchoscopically placed into the right caudal lung lobe of macaque monkeys. Bronchoalveolar lavage (BAL) samples were collected from dust-exposed right lung and unexposed left lung of the same individuals at 2-week intervals for 12 weeks after dust instillation. The samples were tested for N-acetyl-B-D-glucosaminidase activity to determine if the enzyme levels could serve as an indicator of pulmonary injury induced by generic coal dusts when compared to known fibrogenic and nuisance dusts. Installation of generic quartz, anthracite, or TiO2 dusts produced significant elevations of enzyme activity and increased numbers of macrophages in the dust-exposed lobes. Elevations in enzymatic activity and macrophage numbers were greatest in response to generic quartz dust. These results suggest that quantitative levels of N-acetyl-B-D-glucosaminidase activity may be a useful indicator of acute and chronic lung injury following exposure to fibrogenic and nonfibrogenic dusts.IntroductionCoal workers pneumoconiosis (CWP) is an occupational pulmonary disease associated with the inhalation of coal mine dust. An important external factor in the development of CWP is the composition of the respirable coal mine dust. A cause-and-effect relationship exists between coal mine dust and CWP, but it has not been shown that exposure to generic coal dusts will cause CWP [12]. Numerous immunological, biochemical, and cellular changes occur in CWP; however, in this study, only N-acetyl-beta(B)-D-glucosaminidase (NAGase), protein, and alveolar macrophages (AM) will be examined [7, 32, 33]."

Dec 1, 1996

"For a good many years the Bureau of Mines and various state mining experi¬ment stations have endeavored to develop some method of utilizing the immense deposits of lignite in the United States. Work in relent year has indicated that the best method of this is to drive off the moisture and most of the volatile water from the lignite in some form of carbonizing apparatus leaving a residue high in fixed carbon and low in moisture and volatile matter, which by briquetting can be made into a high-grade fuel. The earlier forms of carbonizing equipment tried were complicated, costly to build and keep in repair, and could not be operated intermittently without being seriously damaged. During the year 1922, however the Bureau of Mines devised a very simple carbonizing oven which produces a uniformly well carbonized product. This oven is essentially a vertical shaft with means for supplying raw lignite at the top and discharging the carbonized limited at the lower end. Air in regulated amount is admitted to the shaft at two horizons, and a zone of combustion maintained through which the column of lignite passes. The lignite is thus carbonized by construction of its contained matter and a small proportion of its fixed carbon, leaving most of the fixed carbon in the carbonized product or ""char"". The degree of carbonization can be closely controlled by varying the volume of air supplied to the oven and the rate of travel of the charre down the shaft.The ""lignite char"" produced is a soft material resembling charcoal more than coal or coke, but somewhat harder than charcoal. A typical analysis is shown in the table headed ""Fuels,"" further on in this papers."

Feb 1, 1924

By B. K. Shibler

As a part of the Bureau of Mines' intensive; 'investigation of domestic manganese deposits, ore-dressing studies were conducted on three samples of oxide and silicate manganese ores from various Wyoming properties. The samples wore as follows: 1. A 2-ton sample of ore was obtained by a Bureau engineer during examination of the Caulkins-McGuckin property in the center of Crook County, 10 miles north of Sundance, Wyo. The ore body was described as a vein deposit in rhyolite porphyry. 2. The J. B. C. Mining Co. submitted a 1-ton sample of oxide manganese ore from a property located 44 miles northeast of Rock River in Albany County, Wyoming. 3. A 1-ton sample of oxide-silicate-ore was obtained by a Bureau examining engineer from the Gheen property in the northeast corner of Washakie County, Wyo. The ore body was described as a replacement deposit in a country rock of silicified limestone. As the samples differed widely in physical and chemical characteristics and also in their response to methods of concentration, ore from each property was considered a separate ore-dressing problem.

Jan 1, 1949

By W. A. Selvig

"The tests described in this paper were conducted under the sponsorship of Subcommittee VII on Pulverizing Characteristics of Coal, a subcommittee of Committee D-5 on Coal and Coke, American Society for Testing Materials, with a view to evaluating various laboratory procedures for testing grindability of coal in connection with commercial pulverization of coal for use as powdered fuel. The subcommittee, at a meeting in New York City on February 21, 1934, selected for test four methods that had been developed during the past few years for testing grindabilitay of coal and were being used by coal-testing laboratories in the United States and Canada. These methods are:Bureau of Mines method, Cross method, Fuel Research Laboratory method, and Hardgrove method. Subcommittee VII agreed that the grindability tests should be made on five coals selected to cover a wide range of hardness. The Pittsburgh Experiment Station, Bureau of Mines, was asked to direct the investigation and to prepare representative samples of the coals. Laboratories of the fol. lowing institutions and companies agreed to cooperate by making grindability tests: Babcock & Wilcox Co., Foster Wheeler Corporation, Fuel Engineering Co., of New York, Fuel Research Laboratory of the Canada Department of Mines, and Northwest Experiment Station of the Bureau of Mines.ACKNOWLEDGMENTSHelpful suggestions in planning the investigation were made by A. C. Fieldner, chairman, Committee D-5 on Coal and Coke, A.S.T.M., and chief engineer, Experiment Stations Division, U. S. Bureau of Mines, Washington, D. C., and E. B. Ricketts, research engineer, New York Edison Co., New. York City.The coal samples were supplied through the courtesy of floats, Wheeler Corporation, New York City; Philadelphia & Reading Coal & Iron Co., Pottsville, Pa.; Pittsburgh Coal Co., Pittsburgh, Pa.; and Pocahontas Fuel Co., Inc., New York City."

Feb 1, 1936

By Theodore M. Katz, W. Stephen Brightwell, David E. LeGrande, Joseph J. Hurrell, Jane A. Lipscomb, Nancy Lessin, Lawrence R. Murphy, Michael J. Colligan, Steven L. Sauter, Richard A. Lippin

Revolutionary changes in the organization of work have far outpaced our knowledge about the implications of these changes for the quality of working life and for safety and health on the job. This gap in knowledge is one of the 21 priority areas for research under the National Occupational Research Agenda (NORA)—a framework crafted by the National Institute for Occupational Safety and Health (NIOSH) and its partners to guide research into the next decade. This report was developed under NORA as the first attempt to develop a comprehensive research agenda for investigating and reducing occupational safety and health risks associated with the changing organization of work. Research and development needs identified in the agenda include (1) improved surveillance mechanisms to better track how the organization of work is changing, (2) accelerated research on safety and health implications of the changing organization of work, (3) increased research focus on organizational interventions to protect safety and health, and (4) steps to formalize and nurture organization of work as a distinctive field in occupational safety and health.

Jan 4, 2002

By Edward L. McHugh

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied an 84,165-acre portion of the 84,935-acre Clover Mountains Wilderness Study Area (NV-050-139) in order to evaluates its identified mineral resources. The area studied is in Lincoln County, NV, about 90 miles north of Las Vegas, NV. No mineral resources were identified in the study area. Volcanic rocks are the most common in the study area, consisting mainly of a thick sequence of ignimbrites in a cauldron complex. Cambrian to Triassic marine sedimentary rocks and Cretaceous to Oligocene clastic rocks are along and partly inside the west and south sides of the study area. No mineral production ha s come from the study area, but gold, silver, copper, and fluorspar have been mined nearby. Eleven mines and prospects in or adjacent to the study area were examined. Workings inside the study area include two shafts, 10 and 60 ft deep, and eleven shallow prospect pits at four sites along the west edge.

Jan 1, 1987

By John E. Lambert

Automatic control of drum head continuous mining machines was investigated as a means of reducing respirable dust generated and operator variabitity. Literature survey, manufacturer interviews and mine visits were the major information sources. Technically feasible automation concepts were Identified to control sump and shear rates, cutter head elevation limits and sumping distance. These are the elements of a programmed cutting cycle which maintains peak penetrating force on the cutter, to maximize depth of cut and therefore reduce dust generation. Based on the industry surveys, successful underground hardware demonstrations must be completed in order to stimulate the market demand for these advanced control features.

Jan 1, 1979

By M. J. Kirwan

[There have been large increases in the oil production and casing-head gas production of certain wells on the Quinn dome (northern part of the Lyons-Quinn field of Oklahoma) caused by large volumes of gas under high pressure entering Vie productive oil sand, The oil production of sore of the leases in this part of the field temporarily increased over 100 per cent within a few days after gas entered the oil sand among the leases that had the greatest increases in oil production wore those on which no gas wells were drilled but which were located up-elope on the structure in reference to gas wells on adjoining properties. It is conservatively estimated that 1,444,000,000, cubic feet of gas entered the productive oil sand and, up to January 1, 1924, caused an increase of about 950,000 barrels of oil from this sand. The casing-held gas volumes of a number of wells producing between 25,000 and 75,000 cubic feet of gas per day increased to several hundred thousand cubic feet and a few walls increased to nearly two million cubic feet per day after extraneous gas entered the oil sand from which the wells were producing.]

Jan 1, 1924

By Loren R. Anderson

This Volume documents the use of the Cone Penetrometer data analysis computer programs VERT and HORZ. The programs are interactive in that they prompt the user for input data and allow correction and modification to be made. The programs read data from the results of cone penetrometer soundings and convert the data to values of tan ø. Mean, standard deviation, skew, kurtosis, linear trends and autocorralation are computed by the programs.

Jan 1, 1982

By Graham W. Marks

In broadening the utility of spectrochemical methods 9f analysis of ore samples 3,4/ a procedure employ in the total energy method, has been adapted to determination of silver in ores. Silver is the first element in group I of the periodic table to be studied in the Bureau of Mines program. Two silver lines in the spectrum, Ag X\ 3280.683 and 3382.89lR were used in the study, and the problems that had to be overcome were: (1) Influence of extraneous elements on line intensities, (2) preparation of standard curves, and (3) improvement in equipment and technique to increase accuracy. Sodium, potassium, sulfur, selenium, iron, cobalt, and nickel yielded low intensities and hence low results, particularly on the samples high in silver, but addition of 60 percent or more of lime counteracted these effects. One calibration curve must be used for samples low in silver and other for those high in silver. The chocks with fire assaying were close enough for preliminary or exploratory investigations, and the method is much more rapid.

Jan 1, 1948

As part of a continuing program of evaluating the Nation's crude-oil resource, this report presents information pertaining to resource, primary reserve, and potential waterflood reserve for 3,209 selected reservoirs contained in 24 oil-producing States, as of January 1, 1968. To that date the selected reservoirs had not been subjected to pressure-maintenance or secondary-recovery operations. These reservoirs also met the following parameters: (1) a minimum of five oil-producing wells on January 1, 1968, (2) a minimum of 50 acres areal extent, (3) a minimum of 50,000 bbl of oil ultimate primary recovery, and (4) the principal reservoir energy was other than active water encroachment. The selected 3,209 reservoirs produced 527 million bbl of oil in 1967, about 17 pct of U.S, total production. Primary oil reserve was 4,983 million stb; in addition, there was 6,043 million stb of potential water- flood oil reserve. Oil resource in the selected reservoirs was 59,547 million stb. A brief history and outlook of waterflooding are presented for each State. Depth and producing rate statistics and geologic distributions of production, resource, reserve, and potential waterflood reserve for the selected reservoirs are presented by States in the appendix. Also included in the appendix are description, history, and technique modifications of waterflooding, and a preliminary cost estimate of a closed-system water-injection project.

Jan 1, 1970

By G. M. Potter, S. J. Hussey, R. Havens

The Artillery Peak manganese ores , from one of the largest known manganese deposits in the United States , present a difficult problem in concentration because they are low-grade and the association of manganese and gangue minerals is intimate and complex. The known size of this deposit has justified investigation of processes such as leaching, wherein preliminary enrichment of the original feed might be advantageous .. Therefore , the ore-dressing studies on Artillery Peak ores were carried on with the object not only of making directly marketable manganese products but also of removing acid-consuming calcite and raising the grade of ore for leachingplant feed . Owing to the extent of the deposits , test work was carried on at the Salt Lake laboratories in considerable detail on several lots of ore of varying composition . This paper summarizes the results obtained from laboratory testing of four samples obtained by engineers of the Mining Branch from the Maggie Canyon area of the Artillery Peak deposit . Also included are results obtained from testing one sample of Chapin Group ore , which was considered representative of numerous very low-grade ores submitted from the Artillery Peak district . During the course of the investigations , many data were obtained and compiled , but for the sake of brevity , data of secondary importance have been omitted or condensed and only those tests giving the more pertinent results are discussed in detail ...

Nov 1, 1947

By A. U. Miller

Protection against fire is a greater problem at a coal mine, than at an ordinary industrial plant. Generally mines are located in isolated districts and do not have the protection of city fire departments; consequently fire fighting aquipment must be installed by the mining company. Fire protection around a mine is just as essential as it is in the city.. and undoubtedly is more important if the fire should be underground where many lives would be endangered and all means of escape cut off. A surface fire can generally be attacked from any angle, but an underground fire can be attacked only as conditions will permit.. U. S. Bureau of Mines engineers have investigated many serious mine fires that undoubtedly could have been extinguished in incipiency if a fire extinguisher or fire hose and water had been readily available. In past years very little attention was given..to fire fighting equipment and organization around mines, but in recent years three gen a derde hange of opinion among many of those engaged in mining, and nearly all up-to-date mining companies now have some kind of fire protection about their mine Probably the first company in Illinois to install regular fire fighting equipment and effect a fire fighting organization at its mines, was the Madison Coal Corporation, which operates several mines in Illinois. The main office of this company is in Chicago and the general field office is at Glen Carbon, Ill.

Jul 1, 1930