Search Documents

By E. H. Skinner

An abandoned mine shaft near Omar, in Logan County, W, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US. Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft3. A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor, The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry.

Jan 1, 2010

By Aner W. Erickson

"Magnetite iron deposits on Tolstoi Mountain were examined as part of the investigations by the Bureau of Mines of iron and copper ores on Prince of Wales Island. The Tolstoi Mountain project was a part of a program for investigating mineral deposits in Alaska, under the general supervision of R. S. Sanford, acting branch chief.A preliminary examination was made by S. P. Holt, mining engineer of the Bureau of Mines, in company with John Reed, L. A. Warner, and W. S. Twenhofel of the Federal Geological Survey, on July 14, l943. Three samples were taken, rough estimates were made, and it was proposed that the area be mapped, topographically and geologically,. Dip-needle work was added to the program, and it was decided that, should results warrant, the deposits would be diamond-drilled.From March 26 to May 28, 1944, the deposits were examined thoroughly by Bureau of Mines personnel under the direction of the author. Thirty-two acres were mapped with contour intervals of 10 feet, grids were established covering the principal outcrops, over 1,500 dip-needle readings were secured, and the magnetite bodies were outlined. Additional information was gathered by trench inch and channel-sampling, 600 linear feet of trench being dug and 32 channel samples being cut. Finally, the mapped area was checked for nonoutcropping deposits by taking dip-needle readings at 10-foot intervals along the traverse lines, creeks, trails, and all outstanding topographical features. This re-connaissance work gave sufficient coverage of the 32 acres to eliminate the possibility of further magnetite bodies of any consequence remaining undiscovered.Acknowledgment is made to Nile Johannsen, assayer, Territorial Department of Mines, Ketchfkan, Alaska, for determination of samples.The deposits are on Prince of Wales Island in Southeastern Alaska near Tolstoi Pay, a deep-water indentation at the northwest and of Kasdan Peninsula. The physical features are shown on figures 1 and 2 and the location of the deposition figure 3. Old workings were found on the west side of Tolstoi Mountain; between elevations of 650 and 1,150 feet, at distances of 3/4 to 1-1/4 miles from the east shore of Tolstoi Bay.Access to the area is over a brushed foot trail built by the Bureau of Mines. Topography would permit construction of either surface or aerial tramways at moderate cost but would make road building expensive. Deep-water navigation, permitting inexpensive water transportation, is possible the year around.Kasaan Peninsula is an area of moderate relief, being considerably less rugged than the mainland to the east. Most of the mountains and ridges are less than 2,500 feet in height and show evidence of having been covered by the ice cap of the Pleistocene age. Rock exposures below elevations of 2,000 feet are limited, as extensive overburden 2 to 20 feet deep covers the greater part of the peninsula."

Dec 1, 1948

By Charles G. Patmon

This paper describing the methods of dredging and treatment of gold-bearing gravels at the Lancha Plana Gold Dredging Co.'s dredge is one of a series of similar papers being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The dredge is located near the Mokelumne River, 12 miles west of San Adreas, Calif.; it is accessible by an improved dirt road from Jackson, which is about 20 miles distant.

Jan 1, 1932

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in nongassy noncoal mines and tunnels. This revised and supplemented listing supersedes an earlier publication2 released in 1963. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and outlined in the Bureau's permissible schedules before the Bureau approves it for safe use in mines.

Jan 1, 1968

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers of Alabama, is making a series of washability studies to obtain technically and commercially important data from the productive coal beds of the State. Based on the system followed in these studies, this report consists of screen-sizing and sink-and-float data on the America and Pratt beds at Gorgas, Ala.SAMPLING AT THE MINESAlthough operations were discontinued in 1929, the accessible openings of the old Gorgas mines of the Southeastern Fuel Co. made possible the taking of samples from the America bed at three openings and from the Pratt bed at two openings. A sample was taken from the America bed at the Klondyke opening; a second was taken about 1 rile south of the Klondyke at the Musgrove America opening, and a third sample was taken about 1-1/2 miles south of the Musgrove-America at the Cricket Lodge opening. A sample was taken from the Pratt bed at Musgrove-Pratt No. 1, which is about 3/4 mile east of Musgrove-America, and a second sample was taken at Musgrove-Pratt No. 2, which is about 3/4 mile west of Musgrove-America. The samples ranged in weight from 1/2 ton to 1 ton and were equivalent to approximately a 2-ton sample from each bed. Figure 1 shows sections of the beds at the places sampled.In addition to the samples for washability study, a seam sample for analysis was taken at each of the places sampled. So as to give a representative seam sample for each of the two beds, these samples were combined in the laboratory in proportion to the thickness of the bed at the places sampled."

Jul 1, 1939

By Ann G. Kim

Acid drainage from underground coal mines and coal refuse piles is one of the most persistent industrial pollution problems in the United States: This Bureau of Mines report reviews the acid mine drainage problem generally and describes research currently underway to combat it.

Jan 1, 1982

By L. F. Heising

Ten composite samples of Mesabi Range nonmagnetic taconite from the Hibbing, Minn., area were evaluated by flotation and by reduction roasting-magnetic separation to determine their potential as a future source of iron are. Only one of the composites yielded concentrates that could be considered marketable, using as a criterion a 10-to-1 iron-to-silica ratio. Cursory petrographic examinations of all 10 composited samples and a detailed mineralogical study on 1 sample suggest that unfavorable mineralogical associations between iron and gangue minerals are responsible for their poor beneficiation characteristics.

Jan 1, 1967

By W. W. Adams

[S,1.1.8'"' of explordves -permissible explosivos,21 other high explosives, and black blasting povrder -in the Uni ted States during the caJ.endar yenr 1937 reached a ~ombined total that slightly exceeded the quantity sold in 1936. A larger output was re orted. for permisAiblA and other hig! explosives but asmal-ler for black po~~er. Production of the three classes of explosives totaled 404, 744,294 pounds, more than 3 pel'CGnt over 1336. The total qrumti ty produced included 49,579,441 pounds of perminsibles, 2~8,924,253 pounds of other high ex-plosives, 36,403,950 pounds of black powder in pellet form, and 29,836,65q pounds of bla~k powder in granular form.]

Jan 1, 1938

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

By F. E. Armstrong

This report describes development and application by the Bureau of Mines of techniques and instruments for using radioactive inert-gas tracers to determine flow paths through petroleum reservoirs that have natural fracture systems and for which water injection has been selected as the stimulative production method. A field test was made to prove the techniques and evaluate instrumentation. The feasibility of applying the techniques and instruments to the solution of reservoir problems in other stimulative methods of production also is discussed. Oil commonly is displaced from sandstone host rocks by the action of a driving force that causes the oil to move through interstices of the rock and into production wells. In addition to the requirements of oil being trapped within the sand pores and the presence of an effective displacement mechanism, the rock itself must have adequate permeability to permit flow of oil and other fluids.

Jan 1, 1961

By Jack R. Woodyard

Scientists at the U.S. Bureau of Mines are studying iron aluminides as possible substitutes for stainless steels to reduce the Nation's dependence on imported strategic and critical materials. In a Bureau investigation on the mechanical properties of Fe-28Al, it was found that the material's machining properties were significantly improved at slow tool and feed speeds. Machining techniques normally used for brittle materials failed or were costly. Further experiments using a 5-in (12.7-cm) mill cutter with carbide inserts, operating dry at minimum machining speeds, produced visually smooth sample surfaces with no tool damage. As a result of these experiments and a review of published data on hydrogen embrittlement of iron aluminide under tension, non-water-based (e.g., sulfur-based) lubricants were chosen for production machining. Four-flute, 3/4-in (19-mm) carbide end mills were used at slow speed under lubrication. This latter procedure reduced tool wear and breakage by a factor of 2. Machined surfaces and specimen cross sections were analyzed by scanning electron microscopy to detect microcracking. Tensile tests gave the expected yield and ultimate strengths, indicating that no degradation by low-speed machining occurred. This study extends this work to show that the alloy can be machined at higher speeds using high-speed steel end mills, and that water-soluble cutting oil is a suitable lubricant and coolant.

Jan 1, 2010

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 20 or 30 ampere leak, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1974

By H. P. Greenwald, H. C. Howarth

There was reported in Bureau of Mines Technical Paper 5754/ a series of tests to determine the compressibility and bearing strength of specimens prepared from blocks of potash salt obtained from a mine near Carlsbad , N. Mex . The events leading up to the investigation were sketched in a foreword by George S. Rice , then chief mining engineer of the Bureau ( retired September 30 , 1937 ) ; this foreword also gives a discussion of the possibility of increasing the ultimate total recovery of the potash salt by " second mining" of pillars or by use of a longwall system . In June 1936 , Rice and the senior author visited Carlsbad with H. I. Smith , chief of the mining division of the Geological Survey , to observe mining then in progress and to discuss with the management of one of the mines records of convergence of roof and floor which they were obtaining . It developed that serious thought was being given to the possibility of roof failure resulting from shear at the faces of pillars . There was envisioned the danger of such cracks extending upward to water - bearing strata . Obviously , the simple compression tests of the potash salt then being made would throw no light on this question , and tests of assemblies of potash and roof salts would have to be made . In this connection it is to be remembered that in the mine no sharp division exists between the potash salt being recovered and the nearly pure halite which forms the roof . The interlocked crystalline structure is continuous , and there is merely a very rapid decrease in the proportion of sylvite in a short distance vertically . Figure 2 of Technical Paper 575 shows that two samples near the top of the salt being mined contained , respectively , 51 and 65 percent potassium chloride . Contrasted with this is an analysis of the roof salt given on page 24 of that publication , which showed only 3.6 percent potassium chloride . As the data given in Technical Paper 575 show , the roof salt is much less plastic than the potash salt . The immediate roof may then be thought of as a more rigid stratum of indefinite extent resting on and continuous with yielding supports and loaded uniformly at the rate of 900 to 950 pounds per square inch . Just what thickness of the salt should be considered as immediate roof is uncertain .

Feb 1, 1938

By R. R. Wells, K. C. Vincent, A. O. Ipsen

"INTRODUCTION The Philipsburg Mining District, Granite County, Mont., has been the largest producing area for battery-grade manganese (70 percent MnO2) in the United States since the First World War. Two companies, the Trout Mining Division of the American. Machine & Meals Co., and the Moorlight Mining Co., have intermittently mined and milled 120 to 250 tons of 25-percent manganese ore per day for the production of concentrates of this grade.Investigation of the district by engineers of the Federal Geological Survey and Bureau of Mines indicated that further exploration and develop¬ment would make available additional oxide and carbonate manganese ores for milling and production of metallurgical-grade manganese. If the battery-grade producers converted their plants to the production of metallurgical-grade concentrates, their production also could be increased through greater recoveries.Until February 1, 1944, the Metals Reserve Company, through its agent, the Sunshine Mining Co., purchased milling-grade manganese oxide and carbonate are for stock-piling at Philipsburg. After that time, only carbonate ore was purchased. Based upon the assumption that the stock pile was a true cross-section sample of the producing area, metallurgical studies were made on representative samples from the Metals Reserve stock piles. Testing also was conducted on two other samples of Philipsburg oxide manganese ore obtained by engineers of the Bureau of Mines from the Little Dandy claim of the Donlan group and from the Marie mine. All ore samples tested were found to be amenable to concentration by ore-dressing methods for the production of concentrates that when sintered met Metals Reserve Company specifications for metallurgical-grade manganese."

Nov 1, 1947

By D. W. Bridges

Solvent extraction has become important in recent years as a unit process in extractive metallurgy. The flexibility and simplicity of the technique have attracted widespread attention, and numerous papers describing actual and projected metallurgical applications have been published. However, differences in terminology, procedure, objectives, and standards, as reflected in reports by different operators and investigators, have sometimes made appraisals and comparisons difficult. Consequently, a need appeared for n series of basic reports on the subject. This Bureau of Mines Information Circular is the first of such a series. It deals with the status of solvent extraction in metallurgy, as well as with the rudiments and terminology of the unit operation. In analytical chemistry, extraction of molecular species from aqueous media by immiscible organic solvents has been used for many years to separate and determine chemical elements (61).4 Complex chlorides of iron and other metals are readily soluble in ethers and ketones, as are the nitrates of uranium and thorium. Most metals are extractable as complex salts of some organic reagent, such as dithizone, 8-hydroxyquinoline, or cupferron.

Jan 1, 1962

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No H0155113, "Noise Abatement of Continuous Mining Machines." It describes the noise source diagnosis of a Jeffrey 120M conveyor and the evaluation of several treatments all conducted in a test facility aboveground. The conveyor noise at the operator's position was gradually reduced from 101.5 to 93 dBA using damping, vibration isolation, sound barriers and smoother discontinuities. The underground performance of the selected treatments will be addressed in Volume II of the report.

Jan 1, 1979

"Qatar, crude petroleum, production, annualdata MY 1949-51Quality mine, Ark., coal, carbonizing properties TP 667washabilty study RI 496N. Dak., lignite, grindabilty as function ofmoisture, tests, results RI 5167"

Jan 1, 1960

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different fields and regions as made by the Bureau of Mines Hempel method of analysis.4 Several of these reports include analyses of crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By Lynn L. Rethi

This U.S. Bureau of Mines report summarizes common obstacles found when attempting to implement health and safety strategies in small mines and small businesses in general industry. Recently, the U.S. Mine Safety and Health Administration focused much of its attention on addressing health and safety issues at small mines. Some of the more innovative interventions practiced by small businesses in general industry are discussed for consideration of their applicability to the mining industry. The most effective intervention strategy that was developed for small businesses is the Occupational Safety and Health Administration Consultative Program. The details of this program and other intervention strategies used by small mines and small businesses are presented.

Jan 1, 1995