Search Documents

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By G. St. J. Perrott, G. W. Jones

"In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., a survey was conducted in 1929 and 1930 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by this company. The territory served approximates 650 square miles and includes 46 cities and towns. The transmission and distribution systems are on overhead construction and underground wires and cables run in underground conduits and manholes. There are 17,000 manholes on the system, and also an area in Boston proper served by the Edison tube system. These conduits and manholes are laid in various types of streets from the most modern type of cement roadbed to the older type of loose macadam. The conditions as found could be considered as typical of any public utility in the electric-light and power field. The survey extended over a period of about a year beginning in June, 1929, and ending in July, 1930, and during this time 1,765 different manholes were tested and a total of 4,068 tests were made.Previous to starting the actual survey, one of the writers, G. W. Jones, spent considerable time in Boston determining the best methods of practical· test procedure. In this work cooperation was given by John Campbell, superintendent, special service department, who for a number of years has been making a study of explosions in underground street areas and preventive measures in Boston and various cities.After this preliminary investigation the tests were continued by employees of the Edisun Company. Copies of all records of tests were forwarded to the United States Bureau of Mines Pittsburgh Experiment Station so that the writers were in close touch with the progress of the survey, and changes could be made in the test procedure whenever deemed necessary."

May 1, 1931

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980

By William W. Odell

Certain gas-making processes are in use in Europe, particularly in Germany, which differ radically from those in common use in America. A number of them are of particular interest because they are different. The questions naturally arise: Are any of them applicable to the making of gas in this country and, if so, with what particular type of solid fuel? It is a fact that some of them were developed with consideration of a particular set of conditions and for the utilization of solid fuels available in Germany. The latter fuels, in certain characteristics, are unlike the high-rank fuels commonly used for making gas in the United States; therefore, in attempting to evaluate the various foreign- developed processes with regard to usefulness here, one must give attention to the particular conditions that will prevail in any specified case and also the characteristics and requirements of the process and generator under considera- tion. Three of the processes that were developed and put into commercial operation in Germany, and which have some characteristics in common, are con- sidered in particular in this publication; they are: 1. Lurgi pressure gasification process. 2. Winkler process. 3. The Leuna slagging-type producer-gas process. Each of these processes requires steam and oxygen as gas-maiding fluids. For a number of years, oxygen, has been used in a relatively pure state,. along with steam, in making gas in Germany, and many of the difficulties initi-. ally encountered have been overcome. Although it appears that oxygen recovered from air was first used in this manner as a method of utilizing a byproduct in a plant that used the nitrogen complement in the manufacture of ammonia; more recently, the oxygen was made particularly for the purpose. The fuels - brown coal or lignite used in processes 1 and 2 were not suitable for use in the older and commonly used intermittent-type water-gas generators, and it was necessary, therefore, to devise a different process for gasifying them. A gas of higher heating value than producer gas, was desired, and the use of oxygen (not air) along with steam made possible the production of the desired gas without nitrogen dilution, which characterizes producer gas. Operating data presented herein are based upon observations by, members of the Technical Oil Mission at plants in Germany, on records, and on information vocally given to members of the lässion, including the author, while visiting those plants, and they are believed to be reasonably correct; however, certain hasic observations, comparisons, and conclusions are. made by the author.

Nov 1, 1947

By Cloyd M. Smith

Progressive mine management is placing increased emphasis on improved ventilation as a contribution to better safety , health , and productivity of miners . Management is on the alert for means of bettering the working environment by increasing the flow of air and distributing it more effectively to the working places , having in mind the necessity of avoiding exorbitant ventilation costs . A basic need in planning betterments of this kind is knowledge of existing rates of flow and air pressures , infCoorrmmaattiicon that is supplied through ventilation surveys . Some companies make partial surveys from time to time , but few make complete surveys on a routine basis . This report describes the practice of a large British anthracite -mining company , which operates 24 collieries in South Wales , in carrying out a routine program of ventilation surveying . Ventilation characteristics and climatic conditions in the working places of its collieries are determined at frequent intervals with a view to increasing the effectiveness of ventilation and protecting the health of workers . It is thought that many of the points of the procedure used in making the surveys and in compiling and reporting the results will be applicable to American practice and that a discussion of the program may be helpful to colliery managers who are planning similar work .

Oct 1, 1949

By William W. Adams

A new record in accident prevention was made by the metal-mining a industry of the United States in 1938, as signalized by a lower fatality rate than in any previous year. The rate was less than half as high as in 1911, the earliest year for which figures are available. A good safety record was also established in the prevention of nonfatal injuries, as the injury rate was lower than in any other years except 1931 to 1935, a 5-year period notable for its unusually low injury rates. Employment was more limited in 1938 than in 1937, both in number of men employed and total number of man-hours worked. The number of workdays per man also was smaller than in 1937. Operating companies reported that 7,233 mines were active in 1938 or some part of the year and that the total number of men employed was 103,027. This figure represents the summation of the average number of men employed as reported by the companies, the average for each mine being that for the period during which the mine was active. The number of employees at all mines in 1938 was 15,402 less than in 1937. Reports covering all mines indicated a total of 188 million man-hours worked during the year, or 21 percent less than the nearly 240 million man-hours worked in 1937. In the performance of this work accidents occurred that resulted in the death of 156 employees and the injury of 1.2,722, each injured employee being disabled for more than the remainder of the clay on which he was hurt.. The fatality rate for 1938 was 0.83 per million man-hours worked, which was 9 percent more favorable than the rate of 0.91 for 1937. Nonfatal injuries occurred at the rate of 67.61 per million man-hours worked, an improvement of 10 percent compared with the injury rate of 75.37 for 1937.

Jan 1, 1941

By Jeffrey Y. Foley

The Bureau of Mines sampled surface exposures of podiform chromite in the Caribou Mountain-Melozitna ultramafic belt in the Kokrines-Hodzana Highlands, central Alaska. Fieldwork began in 1979 as part of an assessment of the mineral potential of lands adjacent to the trans-Alaska pipeline corridor, for the Bureau of Land Management, and continued through 1981 as a Bureau of Mines investigation. The belt comprises six complexes of which the three closest to the pipeline corridor were investigated. Concentrations of chromite disseminated in dunite host rock make up mineralized intervals ranging in thickness from less than an inch to 5 ft and in grade from 3 to 23 pct chromium. The largest occurrence has an exposed strike length of 80 ft. Bulk surface samples were collected from 10 of these exposures, and beneficiation tests on the samples produced concentrates of metallurgical, refractory, and subindustrial grades. Part I--this report--describes the fieldwork; part II--1C 8916--describes the beneficiation work.

Jan 1, 1983

By authority of the Federal Coal-Mine Inspection Act of May 7, 1941, Public Law 49--77th Congress, H.R. 2082,2/ a Coal-Mine Inspection Division was established in the Health and Safety Branch of the Bureau of Mines. Funds totaling $729,000 for the operation of the division and for other incidental expenses were provided in an amendment to the Department of the Interior appropriation bill for the fiscal year 1942 (H.R. 4590). A small. percentage of these funds was made available on July 1, 1941, and a much greater proportion on October 1, 1941, to defray the expenses of the coal-mine inspection work and incidental activities for the remainder of the fiscal year 1942. The Coal-Mine Inspection Division is charged with administering the act and is required to compile, analyze, publish, and otherwise make available for public inspection the information obtained under it and to transmit such information to the Director of the Census. The act requires also that the information obtained be reported to Congress, with such findings and comments thereon and such recommendations for legislative action as may be deemed proper.

Jan 1, 1943

By J. F. Neill, O&apos

[The Cartersville mining district is in Bartow County, Ga., about 40 miles northwest of Atlanta. Barite, limonite, ocher, amber, hematite, and, manganese oxide ores have been produced from the strict since about 1840. In the search for a possible source of manganese ore, Bureau of Mines engineers made a preliminary study of the district from September 1950 to January 1951. During this study 139 deposits were examined, and many mineral exposures were sampled. Manganese mineralization occurs as fine oxide and concretionary pellets in residual clays, as fine oxides in umberous clay, in brown-iron deposits, and in a limited quantity in mud ponds and Jig-tailing piles. The future supply of ferrograde manganese ore from the district, using current mining and benefication methods, appears limited to the recovery of the hard manganese ores deposits. Rough estimates indicate a reserve of manganese-bearing clays of about 8,000,000 long tons. This type of deposit has been extensively exploited and the larger deposits mined out to depths of from 50 to 200 feet. The remainder of these deposits are low grade, are covered with deep layers of colluvium, or lie below the ground-water table. Any future production from this source will require systematic prospecting, improved concentration, and an increase in the price of concentrate.]

Jan 1, 1954

By C. C. Hwang

The Bureau of Mines formulated a method for calculating the concentration of entrained dust from a dust deposit by a turbulent gas stream. In particular, a diffusion equation is used to calculate dust concentrations in a channel following an explosion. Dust leaving the channel walls was treated as originating from stationary or moving, and single or multiple material sources. Formulas and sample computations for various types of dust sources in circular and rectangular channels are given, based on experimental entrainment rates. The analysis predicts the dust concentration as a function of time and channel space. The results appear to agree with the physical characteristics of explosion-driven dust dispersion in a O.6-m-diameter, 50-m-long explosion tunnel. The analysis is also applied to simultaneous and consecutive dispersion of coal and rock dust from simulated coal mine surfaces (walls, floor, roof, and ribs).

Jan 1, 1974

By Wallace W. Roepke

The Bureau of Mines tested new designs of drag bit cutters with sintered diamond inserts instead of standard tungsten carbide tips. The bits were tested for orthogonal cutting forces, primary dust generation, and incendivity, with a standard plumb-bob type conical cutter (600 included tip angle) as the reference. Preliminary wear and impact-failure testing were also done. The results were mixed. Two new designs had forces similar to those of the reference bit, but one new design had about twice the normal force. This same design had almost twice the specific energy during shallow cutting but generated an equal or slightly lower amount of primary dust than did the reference bit. Incendivity was eliminated for two radial designs. One conical design had ignition only after more than 15 impacts, but the other conical design was incendive. Impact failure occurred, but not so quickly as anticipated. Over 7,500 impacts on a sandstone face, with a total cutting distance of more than 1,981.2 m, only scuffed the leading edge of the sintered diamond cutting face but put hairline cracks in the substrate mounting pad. Additional design and testing are needed to develop an optimum cutter, but prospects look good for this material.

Jan 1, 1983

By W. S. Wright, A. W. Tolonen

"INTRODUCTION The Mount Andrew iron deposit on Kasaan Peninsula, Prince of Wales Island, Southeastern Alaska, was examined in August 1942 by an engineer 4/ of the Bureau of Mines accompanied by geologists 5/ of the Federal Geological Survey. From October 20 to 27, 1942, two engineers 6/ of the Bureau of Mines made a further preliminary examination and took three large samples of magnetite and magnetite-copper ore for metallurgical testing. During the stunner of 1942 an investigation of the Mount Andrew-Stevenson-Mamie area, including topographic and geologic mapping and a magnetic survey, was made by geologist 7/ the Federal Geologically Survey. On May 31 and June 2, 1943, two Bureau of Mines engineers 8/ conducted a preliminary examination in which special attention was directed to trails, camp, and drill sites. They were accompanied on May 31 by L. A. Warner of the Geological Survey.During the period from September 1943 through September 1944 Bureau of Mines engineers 9/ completed a thorough investigation which included trenching, core drilling, and sampling. A Federal Geological Survey representative 10/ examined all trenches and cores for geological data.LOCATION AND ACCESSIBILITYThe deposit is situated at latitude 55º 31' N. and longitude 132º 18' W. on the north side of Kasaan Bay on Prince of Wales Island, Southeastern Alaska. The general location is shown on figures 1 and 2. The deposit is 5 miles southwest of the village of Kasaan and by water, 27 miles northwest of Ketchikan; the main tunnel portal is 7/8 mile north of the Mount Andrew landing on Kassan Bay."

Nov 1, 1947

By Gerald W. Elger

To determine the feasibility of removing nonferrous metal impurities from automobile scrap by thermal treatment in a rotary kiln, the Bureau of Mines conducted four series of tests with synthetic scrap mixtures heated at various temperatures under oxidizing and reducing conditions. The treated scrap mixtures were melted in an electric-arc furnace and cast into small ingots for impurity evaluation. Analyses showed that the ingots were essentially free of residual metal impurities except for copper. Test data indicated that in an oxidizing atmosphere the percentage of copper removed increased with treatment temperature. Percent of copper removed in a reducing atmosphere was found not to be temperature dependent. A significant finding was that copper was embrittled under some of the operating conditions and was mechanically removed by fragmentation.

Jan 1, 1968

By W. W. Adams

The metal and nonmetallic mineral mines (excluding coal mines) of the United States had a more favorable safety record in 1935 than in any year except 1931 and 1932 since annual statistics of accidents first became available in 1911. The accident rate was even lower than that for 1911, when the recorded rate probably did not reflect all of the accidents that actually occurred because many companies had not yet begun to keep complete records of accidents, especially those causing only minor injuries, and when, therefore, the number of accidents revealed by the companies' reports to the Bureau of Mines was probably not as complete as that reported for later years. Compared. with 1911, the accident rate covering fatal and nonfatal injuries in. 1935 decreased 13 percent. Compared with 1925, when the rate was the highest ever reported, the rate for 1935 decreased 47 percent and compared with 1934, 7 percent. The progress in safety which the mines of the country made in 1935 was not confined to any section or mining region; it was shared by a majority of the mining States and applied to underground mining operations, to open-pit mining, and to work at surface shops and yards. The rate for underground mining declined 8 percent from 1934; the rate for open-pit mining declined 14 percent, and that for surface shops and yards 12 percent.

Jan 1, 1938

By Charles D. Litton

This Bureau of Mines report presents a discussion of the essential components of pneumatic monitoring systems and their associated functions. Design criteria are presented which can be used for the design and fabrication of pneumatic monitoring systems having total system response times on the order of 15 to 30 min. To illustrate the utility of these design criteria, two detailed design examples are presented,

Jan 1, 1983

By Gene Asai

The Bureau of Mines investigated the caustic extraction of alumina and soda from retorted dawsonite-bearing oil shale, as part of a program to devise technology for treating alternative domestic sources of alumina for the production of aluminum metal. Colorado oil shale yielding 13 pct oil (35 gal/ton) and containing 12 wt-pct dawsonite (representing about 4 pct extractable alumina) was retorted to obtain oil-free (spent) shale Spent shale was leached with dilute NaOH to determine the effect of particle size, retorting temperature, leaching variables, and storage conditions on extraction of alumina and soda and dissolution of impurities. Maximum alumina and soda extractions were obtained by promptly leaching minus 28-mesh spent shale, obtained by retorting raw shale at about 5000 C, with 0.5N NaOH. Under these conditions, dissolution of impurities such as Ca, Fe, Ti, and P was low. Leaching tests were made on spent shale stored for periods of up to 30 days at 0° to 42° C and at 0 to 100 pct relative humidity (RH). These tests indicated that significant reductions in alumina extraction would occur if spent shale were stored in ambient Colorado air under naturally fluctuating temperature and humidity.

Jan 1, 1983

By Robert J. Evans

The monorail bridge conveyor (MBC) is a prototype continuous face haulage system that was surface tested and evaluated by the Bureau of Mines. The MBC consists of a series of cascading belt bridge conveyors suspended from roof-supported monorail track. Tests were conducted to determine MBC haulage capability, maneuverability, power consumption, and reliability using rigid and chain-suspended monorail track installations. Subsequent modifications to improve operation and reliability made during surface testing are described. Mining plans were devised to show potential MBC installations for room-and-pillar, longwall development, and shortwall mining sections. Compatibility tests were conducted with the Bureau's prototype hopper-feeder, to provide additional surge capacity and lump-breaking capability. Results from the surface test program, along with modifications to improve system operation and reliability, indicate that the MBC has the potential to perform success- fully in an in-mine trial.

Jan 1, 1987

By William Seymour

"INTRODUCTION Byproduct-coke manufacture is one of our country's most essential in¬dustries; its importance was strikingly accentuated by the demands of World War II. This paper reviews recent progress in various phases of byproduct-coke operations for the production of metallurgical coke particularly that used as blast-furnace fuel.In the early days of the by-product-coke industry in the United States high-grade bituminous coking coals, both high-volatile or gas coal and low-volatile Pocahontas coal, were plentiful, and the selection and mixing of coals for coke-oven use were minor problems.The demands of World War I for the production of iron, steel, and coke aroused and stimulated new interest in the investigation of the reserves, characteristics, and properties of our coking coals. During that war the increased demand for coke reached a critical stage, and the shortage of high-grade coking coals necessitated the use of cols of inferior quality and of different coking characteristics than those previously used.The period of prosperity following World War I brought much progress and development in the by-product-coke industry. Methods of testing coal and coke were improved. The search for satisfactory coking coals was continued, and construction and design of byproduct ovens were improved."

Jun 1, 1946

By Jarrell C. Grout

The Bureau of Mines has developed a computer program for use in solving nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship, the unknown parameters may be evaluated by either the Gauss-Newton or the Newton-Raphson methods of iteration. Variances and covariances of the parameters, as derived from the law for the propagation of errors, are also determined.

Jan 1, 1969

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010