Search Documents

By K. J. Liles

The Bureau of Mines conducted laboratory semicontinuous and continuous heavy liquid tests to determine the feasibility of producing commercial-grade products from the high-clay sylvinite ores of the Permian Basin in New Mexico. Continuous test operations demonstrated that concentrates containing 59.9 percent K2O and recoveries of over 75 percent of the contained potash can be obtained. The organic heavy liquid was effectively recovered by vaporization, condensation, and absorption methods. Less than 5 parts per million of heavy liquid vapors were released to the atmosphere. This loss represents only 0.02 pound of heavy liquid per ton of ore treated.

Jan 1, 1973

By William R. Wayment

The objective of this investigation was to obtain data on friction-head losses of sand slurries during their transport in pipelines. The data ultimately will be used in designing hydraulic transport systems. Information that was incidental to the primary objective was gathered on degradation, changed percolation characteristics, and critical velocities of the slurries~ Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Approximately 2,000 tests were run in the pilot plant. The ranges of flow velocities used in the experiment were 2.8 to 19 f.p.s. in the 2-inch line, 4 to 14.5 f.p.s. in the 3-inch line, and 4 to 11 f.p.s. in the 4-inch line. Velocities were varied in increments of 0.5 f.p.s. through the entire velocity range in each pipe size. Densities were varied in 3-percent increments from 40 to 70 percent solids by weight except for one series of tests in the 2-inch line; in this series, densities were varied in 5-percent increments from 5 to 65 percent solids by weight.

Jan 1, 1962

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By Alla D. Mah

Compilation of data on materials of metallurgical interest is one of the important activities of the Berkeley Thermodynamics Laboratory of the Bureau of Mines. Recent renewed interest in metallurgy of vanadium renders the present compilation a timely guide for experimentation to improve present methods or to develop better methods of extractive metallurgy. Thermodynamic data for vanadium and its inorganic compounds have been critically surveyed, selected, and compiled into one convenient reference from which information can be readily obtained for evaluating heat balances, determining trends, and establishing limits of metallurgical processes. By indicating the direction of experimentation, this report enables the saving of time, effort, and expense which would otherwise be necessary for trial and error experimentation. Much of the data has been obtained experimentally at the Berkeley laboratory. Other data were collected through an extensive survey of worldwide literature through April 1965. Estimates were made when no data were avail-able. Data on the vanadium halides was sparse, and the results derived from existing data were at times divergent. Some of the selected values for the halides may need modification as more or better experimental data become available.

Jan 1, 1966

By T. A. Henrie

A technique was devised for measuring the rate of chemical reactions between reactive metals and molten-salt mixtures at high temperatures. The rate of the heterogeneous reaction between high-purity titanium metal and titanium trichloride in molten sodium chloride was determined. The reaction is surface-controlled, and the heat of activation is 8.29 kilocalories per mole TiC13. An active site or reaction nuclei is created by adsorbing a TiC13 molecule at the metal surface. Reaction of the second TiC13 species forms an activated complex that decomposes into three TiC12 molecules.

Jan 1, 1963

By Robert S. Sanford, Harold C. Pierce

"At one time the Alaskan Eskimo lived in many small settlements scattered along the Arctic coast. These settlements extended as far south as Bristol Bay and several miles inland on the large rivers. When the white man established trading posts, schools, hospitals, and missions, these people gradually congregated around them in a few large villages. The natural fuel supply near many of the large villages along the Arctic coast became exhausted as a result of the abnormally large influx of people from small outlying settlements.The population of Barrow, Alaska, according to the 1940 census, is 363 persons, but since that time it has increased considerably, and later estimates place the present population between 400 and 500 persons. With the exception of 25 white persons, the entire population is comprised of Eskimos.The government maintains a school, hospital, radio station, and weather station at Barrow. In addition to the government, installations, there is a church, a privately owned trading post, and cooperative store owned by the Eskimos.For many years the Barrow Eskimos depended on driftwood and petroleum residue from Cape Simpson for their fuel supply. This fuel provided not only warmth for the Eskimo during the long cold winters but also heat for melting ice, the only source of 'water during .the winter. In recent years the sources of petroleum residue and driftwood have not been adequate to meet the demands for fuel During the winter of 1942-43 and again in 1943-44, Barrow experienced an acute shortage of fuel.The fuel problem at Barrow was brought to the attention of Governor Ernest E. Gruening, who was instrumental in getting a Bureau of Mines engineer4/ to investigate reported coal occurrences in the vicinity. Coal deposits along the Meade River and at Peard Bay were examined during the spring and fall of 1943. The Alaska Native Service shipped in mining equipment in September 1943 and commenced stripping an open-pit mine on the Meade River in June 1944. In conjunction with this work, an engineer5/ of the Bureau explored by churn drilling to determine the tonnage of- coal in the vicinity of the mine. In addition to this work, the Bureau of mines examined coal deposits in Peard Bay area and along the Kuk River south of Wainwright."

Nov 1, 1924

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By W. H. Coghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization; and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed 'and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number S0241073 by Fenix & Scisson, Inc. to the Denver Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By F. A. Penning

An experimental and analytical investigation was conducted on a recoverable pit bottom buffer. Work was conducted at the Colorado School of Mines using the U.S. Bureau of Mine-s free fall test tower. The four-sided butter, one of several designs by Cable Belt Ltd., was constructed of reinforced rubber slabs. The kinetic energy of falling weights, 1670 to 6000 lb, was absorbed by the flexure of rubber slabs loaded along their edge. A series of constant energy, 3000 ft-lb and maximum design velocity, 600 fpm tests were conducted. Static testing of the buffer established the load-deformation behavior. A large hysteresis loop plotted above and below the data published by the manufacturer. Creep was evident during; the loading Lend unloading cycle. Electronic instrumentation measured deceleration using your accelerometers; overall and intermediate movement was found from four displacement transducers; bending strains were recorded at four locations; and base reactions were measured by using four load cells. Data were recorded on tape and played back on a recording oscillograph. High speed movies were taken of all the tests. Symmetry of response and rebounds, when they occurred, were noted. From the displacement-time and load-time data, maximum decelerations were calculated by four methods and different assumptions. Good agreement was found from these approaches. Impact loads ranged from a low of 0.7 to a high of 6.1 gs. A dynamic computer model was written for the response of the buffer. Displacement-time, and acceleration-time plots show close correspondence with experimental data for the ten experiments. Data from accelerometers, displacement transducers, strain gages, and load cells are included. The computer program listing, and displacement-time acceleration-time plots are also presented.

Jan 1, 1980

By A. J. Forney

The hot-gas-recycle process, for the hydrogenation of carbon monoxide, was investigated in a 12-inch-diameter reactor. Initially because the distribution of gas was poor, hotspots developed in the catalyst bed. After the velocity profile of the gas flowing through the bed was studied, the method of packing the catalyst was altered. Because this change improved the distribution of gas, temperature control was excellent. The l2-inch-diameter reactor was operated successfully in the synthesis of gaseous and liquid fuels. When high-Btu gas was synthesized in two stages, parallel-plate assemblies of Raney nickel were almost as active as granular Raney nickel in the second reactor. The pressure drop through the second reactor, however, was reduced 90 percent by the use of these assemblies.

Jan 1, 1962

By E. E. Maust

The present work is part of an ongoing Bureau of Mines effort to provide a better understanding of the fundamental phenomena involved in sulfide flotation, the role of oxygen in xanthate adsorption being one essential issue. Galena was chosen as the material around which to develop a conceptual model, partly because of its demonstrated oxygen sensitivity and partly because information on its properties and flotation behavior constitutes the largest part of the fundamental information available on sulfides of commercial importance. The model is formulated primarily in terms of surface electronic energy levels produced by oxygen and xanthate and is further developed using existing experimental evidence and its implications. Four major functions of oxygen are elucidated, and the relationship of these to the formation of lead xanthate, dixanthogen, and a surface compound is discussed. Though yet incomplete, the model provides a useful framework within which the results of diverse experiments can be related to one another in their proper perspective, as shown by a brief discussion and resolution of some apparently discordant results reported in the literature.

Jan 1, 1976

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By J. E. Fraley

Full-column anchored resin bolts were first used in underground mines in 1972. These bolts appear to improve support in many roof bolt applications, as indicated by the use of about 30 million resin bolts in 1980. In the mid-1970's, Bureau of Mines in-vestigators began looking for a substitute for resin because of its short supply and rapidly increasing price. The investigators selected accelerated gypsum plaster (CaSO. ·1/2H20), which becomes gypsum (CaSO.· 2H20) when mixed with water. Gypsum makes an effective alternate grout material because it hardens quickly, is readily available, and is inexpensive in comparison with other cementitious materials. The Bureau received a patent (U.s. patent 4,096,944) for a system combining water capsules (wax-encapsulated water) with plaster into cartridges resembling resin cartridges. This report presents the results of tests conducted by the Bureau on the plaster, the water capsules, and their combined use in cartridges. The tests were designed to determine how the gypsum-plaster water capsule bolting system performs and what happens in the hole while the bolt is being inserted through the cartridge. The test results indicate that water capsule plaster cartridges are a workable alternative to resin cartridges under normal or dry conditions.

Jan 1, 1987

By John L. Edwards, Anthony T. Iannacchione

There has been a persistent need to forecast roof falls so that miner’s exposure to hazardous underground environments can be minimized. Several monitoring techniques have been developed and are used today with varying levels of acceptance in the mining industry. This paper examines the potential for monitoring microseismic emissions activity as a means of forecasting roof falls. The use of this activity to forecast roof falls has drawn only limited attention, resulting in a lack of published field performance data. This deficiency is being partially addressed by analyzing data obtained during longwall mining at Moonee Colliery in 1998. The Moonee data base contains a wealth of information concerning roof fall forecast parameters and the seismic alarm criteria used to develop these forecasts. Four seismic alarm criteria were developed and used by Moonee with varying degrees of success. Roof falls were forecasted 73% of the time with average forecast times of 54 minutes. Ninety percent of the predicted roof falls had a warning time, i.e., the time between warning and roof fall event, of greater than 1 minute. The fraction of forecasted roof falls decayed logarithmically as a function of warning time, until only 20% of events were predicted more than 100 minutes prior to roof falls. False alarms occurred in 50% of the warnings. Many of the false alarms were quickly followed by a cessation in mining which could have temporarily halted the on-going failure process. If mining had continued immediately after the false alarms, a roof fall may have occurred soon after. The microseismic activity collected from Moonee Colliery demonstrates that techniques to forecast roof rock instabilities in underground mines are possible.

By L. J. E. Hofer, J. L. Snyder, J. N. Barn, J. E. Chilton, W. E. Thomas

Various silicone materials have been proposed for use in mining environments. The catalytic methane sensors now employed are poisoned by silicone vapors. Activated charcoal and carbon cloth adsorbents will increase the sensor lifetimes in an environment containing significant silicone vapor concentrations. The results of a study of catalytic methane sensor operation with adsorbent materials in hexamethyldisiloxane-air mixtures are reported. Sampling techniques developed for measuring silicone vapor content of mine atmospheres are described.

By David J. Kusler

This Bureau of Mines study is an appraisal of the demand for platinum, should this strategic metal be used as a. catalyst in the National abatement of automobile exhaust pollution. The Clean Air Act 0f 1970, as amended, requires that automobiles produced in 1975 and thereafter be provided with antipollutive measures to control automotive exhaust emissions. The study considers the need for automobile pollution control, the methodology for such control, the annual primary (new) platinum demand for automobiles produced from 1975 to 1990, primary platinum availability, and supply-demand forecasts and outlook. The correlative demand for platinum for the production of the required unleaded gasoline is also considered. Methodology for the study included a forecast of new automobile production from 1975 to 1990, development of automobile survival and retirement data, estimates of new platinum demand under various conditions of salvage, and data on recycling the precious metal from the catalytic converters of scrapped vehicles and existing vehicles when their spent converters are exchanged for replacement units. The new platinum demand for automobile exhaust converters, based on a converter service life of 50,000 miles, is estimated to be 1.41 million troy ounces initially in 1975, rising to 1.68 million in 1980, and declining curvi-linearly to 0.94 million in 1990. The platinum demand for converter longevities other than 50,000 miles can be derived from the tabular data presented. An appendix to the report presents a comparison between longevities of 50,000 miles and 25,000 miles. The petroleum industry's demand for new platinum for the production of lead-free gasolines could total as high as 1 million troy ounces between 1972 and 1981, just for expansion of isomerization and reforming capacity, and is in addition to normal operating demand for this metal.

Jan 1, 1972

By Forrest T. Moyer

Injury experience at metal mines and mills (excluding officeworkers) in 1964 was 60 fatal and 3,672 nonfatal disabling work injuries during an exposure time of 149 million man-hours worked. These injuries occurred at a frequency rate of 24.57 per million man-hours and had a severity rate of 3,687 days lost or charged per million man-hours. Employment at 2,363 metal mines and 291 mills, excluding officeworkers, was 68,140 men in 1964. The average number of days worked was 274 The principal cause of fatal injuries at all mines and mills was haulage accidents and in underground mines, only, was falls of ground. The principal cause of nonfatal injuries was handling material accidents. The frequency rate at metal mines and mills in 1964 was slightly below that of 1963, whereas the severity rate was higher. Injury experience at 94 primary nonferrous smelters, refineries, and reduction plants (excluding officeworkers) was 8 fatal and 999 nonfatal disabling work injuries during a worktime of 98 million man-hours worked. The combined injury-frequency rate in 1964 was 10.29 and the injury-severity rate was 1,005. The 36,956 employees worked an average of 329 days during 1964. The principal cause of injuries at these plants was handling material accidents.

Jan 1, 1968

By Ronald T. Mayerle

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 20,500-acre part of the 104,085-acre Rincon Wilderness Study Area (OR-002-082) in order to evaluate its identified mineral resources. The wilderness study area is located in Harney County, OR, about 12 miles west from Fields. No mineral resources were identified within the study area. A literature search found no records of mining or minerals exploration, nor did a ground search find any evidence of mining-related activity. Of seven alluvial samples taken from the major drainages of the study area, all were barren except one. This sample, taken from a dry streambed along the southern boundary, contained $0.07 gold per cubic yard; however, this small amount of gold is of no economic significance, and the source is probably outside the study area. The Pueblo-Steens mining district extends to within 4 miles east of the study area. No evidence of geological environments similar to those that were responsible for the formation of resources or occurrences of metals and nonmetals within the district is known within the study area.

Jan 1, 1987