Search Documents

On the 26th of June 2000 a hydraulic fill retaining barricade failed at the Bronzewing mine in Western Australia. The barricade failure resulted in the release of 19,000 m3 of saturated hydraulic fill into the mine and caused the deaths of three miners. Following this tragic accident, the practices and procedures of mines using hydraulic fills came under intense scrutiny by regulatory bodies and mining companies. At this time, the use of hydraulic fill at Normandy?s zinc/copper Scuddles mine was suspended and waste rock became the sole backfill material in use underground. By 2003, development of the adjacent Gossan Hill mine had progressed to a point where a self supporting fill material was required to enable full recovery of high grade ore. Cemented hydraulic fill (CHF) was identified as the optimal fill type and work began on designing appropriate management procedures and controls to ensure the safe implementation. This work included definition of the fill properties, plant design and construction, reticulation system design, design of stope barricades and drainage systems and fill placement control and monitoring practices. CHF placement began on 16th July 2004 and has continued to date. Significant operational experience has since been gained in areas including plant performance, fill product quality assurance, barricade construction, stope drainage and in-situ performance.

May 1, 2007

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By J. P. Jarrell

Environmental considerations are of increasing importance in determining the acceptability, schedule and cost of expansion ofCanada&apos;s uranium processing industry. Environmental considerations must be addressed in the early stages of facility planning. This results in a dilemma, as the process data needed to predict physical environmental impacts are not yet available from process design activities. Hence, a business risk is incurred if plant design is carried forward to meet these requirements prior to project (or site) approval. On the other hand, project scheduling normally mitigates against leaving process design engineering until such time as project approval is obtained. This paper examines the experience gained in Eldorado Nuclear&apos;s proposed expansion of refining capacity as viewed by an environmental engineering consultant. The history of the project and the relationship to process design functions in the two-year period prior to the Port Granby environmental hearings are reviewed. During the Port Granby public hearing, there was a consensus that normal operation of the proposed refinery could be successfully integrated with the site&apos;s natural environmental constraints. Moreover, the radiological impact from plant operations was demonstrated to be inconsequential. However, concerns were raised relating to plant upset and accident situations. These concerns are summarized. Process data requirements identified during the environmental hearings are discussed. Finally, the concerns for on-site burial of radioactive waste are reviewed. These concerns focussed on long-term stability of the waste in the presence ofgroundwater transport, erosion and glaciers. The AECB&apos;s position on waste management with regard to this project is reviewed in light ofthe implications for design.

Jan 1, 1979

By R. N. Chakravorty, K. K. Feng

"There is growing evidence that modern methods of mining coal increase the risk of spontaneous combustion. Seemingly unimportant at this time, this hazard could prove to be a barrier to growth and development of the coal industry in some areas of Canada. The paper presents bedrock knowledge on spontaneous combustion gathered by scanning and evaluating current technical and research literature. Special efforts have been made to identify significant coal and environmental factors and to establish criteria for susceptibility. In addition to the state-of-the-art knowledge, preliminary results from on-going studies are discussed."

Jan 1, 1973

By Michael I. Brittan, Craig M. Sams

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations using very large SAG mills fitted with variable speed drives. Low-aspectratio single-stage SAG mills were introduced in South Africa to process the consistent gold bearing Witwatersrand quartzites. Elsewhere, circuits were patterned after the more conventional North American circuits with high-aspect-ratio SAG mills followed by ball mills. This paper provides information on two recent Gold Fields group installations covering both types of SAG mill in large, single-stage applications. While these operations process similar tonnages, the mills represent opposite ends of the aspect-ratio spectrum. The Tarkwa mine in Ghana employs a low-aspect 27’ x 42’ 14MW SAG mill. The St Ives mine in Australia operates a conventional 36’ x 18’ 13.4MW SAG mill.INTRODUCTIONGold Fields is one of the world’s largest gold producers with annual production of approximately 4.2 million ounces. The Gold Fields group has operations in South Africa, Ghana and Australia, along with numerous exploration sites and advanced projects in several other countries. This paper discusses new milling operations in Ghana and Australia.TarkwaThe Tarkwa Gold Mine is located in Ghana, West Africa, approximately 350 kilometers west of the capital city of Accra (Figures 1 and 2). The site conditions are tropical with an average annual rainfall of 1,930 mm and a maximum temperature of around 35°C."

Jan 1, 2006

By E. V. Neelands

THE Canadian Malartic mine is in Western Quebec, about fifty miles east of Noranda and forty miles south of Amos on the Canadian National railway. The recently constructed branch of the railway from Rouyn to Senneterre passes half a mile north of the mine. HISTORY he property was discovered in 1923 &apos;by St. Barbe Sladen, H. S. Kennedy, and J. C. Carroll, who were prospecting for an Ottawa syndicate and found gold in a small quartz vein near the present workings. Five claims were staked and were optioned to an exploration company, who allowed the option to lapse after surface sampling and diamond drilling eighteen holes. Some months later, the property was sold to Malartic Gold Mines, Limited, who carried on development until 1929. A vertical shaft was sunk and exploration work done on three levels, supplemented by diamond drilling 16 surface holes and 62 underground holes. The work indicated that the important ore occurred in two silicified.zones in schisted greywacke which intersected west of the shaft and were believed to be controlled by a drag-fold. The ore grade was not considered sufficiently favourable to war-rant an operation, and work was terminated. With the advance in the price of gold to $35 per ounce, interest was revived and a new Company, Canadian Malartic Gold Mines, Limited, was incorporated for further development. The shareholders of the old Company accepted a new position under which their interests were protected, and sufficient treasury shares were optioned to Ventures, Limited, and Sudbury Basin Mines, Limited, to provide funds for further exploration of the prop-erty to determine whether, under the new economic conditions, profitable operation would be possible, and, if advisable, to provide the equipment for production. Additional claims were acquired, bringing the total area up to 1,029 acres.

Jan 1, 1939

By R. D. Lawrence

"Comparable transaction analysis is the best known of the market approaches to valuation of exploration-stage mineral properties. The analysis of option and farm-in agreements can also provide useful guidance to valuators. While such approaches can be distorted by incomplete analysis, market-based methods are capable of providing consistent, credible results when carried out carefully with due consideration paid to all factors which buyers and sellers consider when dealing in the real market. IntroductionMineral properties without defined resources present one of the most challenging tasks to the mineral valuator. This paper will concentrate on market-based approaches to valuation of such properties. Other authors at MM2000 presented papers on cost and income approaches. Sorentino (2000) also provides a useful overview with some provacative commentary on methods.Market based-approaches are based on the principle of substitution and include such techniques as: comparable transaction analysis (sometimes referred to as sales comparison analysis); farm-in commitment (or option agreement) analysis; rules-of-thumb; and comparable market value analysis.Are there any valuation standards available to assist the valuator? In Canada there are none that apply to the valuation of mineral assets or securities. This problem is being addressed, at least in part, by the CIMVal Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM)1. Further, the recently established Canadian Association of Mineral Valuators will be giving consideration to the adoption of valuation standards."

Jan 1, 2002

By John R. Goode

"The year 2011 witnessed a major surge in rare earth prices as China, supplier of +95% of the world’s rare earths, reduced export quotas and increased export taxes and duties. In response, companies around the world are scrambling for alternative sources. In Canada too, there is a race to be the “first” rare earth producer. Something that is not generally realized is that Canada has a long history of rare earth production and was a major supplier from the early 1960’s to 1990. At one stage, Canada was said to be supplying more than one third of the world’s yttrium and probably supplied even more than that. Five decades ago, thorium was a key element in many non-nuclear applications and Canada became a major supplier of thorium from the late 1950’s to 1968, first as a by-product of uranium and then as a co-product of rare earths. This paper reviews the development of Canada’s original rare earth and thorium production facilities, which were located in the Elliot Lake uranium camp in Northern Ontario. The uses of these elements, geology, mineralogy, markets of the time, and processing are all discussed. Some of the lessons learned from these pioneering operations might be useful in today’s race to develop the next generation of rare earth production plants.INTRODUCTION The rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960’s the invention of rare earth-based phosphors for the cathode ray tube in colour television sets launched a major demand for certain rare earths. The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950’s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950’s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths. Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available for thorium and the rare earths but unquestionably Elliot Lake production made a significant contribution to world production. This paper is intended to present as much of the information that is available."

Jan 1, 2012

By R. D. Lindsay

"Pamour Porcupine Mines, Limited is involved in the mining, milling and primary refining of various gold, gold - copper and refractory gold ores. Pamour operates five mines in the Porcupine Mining District of Ontario, and two 2,550 t/d milling facilities.Both metallurgical facilities use conventional cyanidation technology including zinc cementation for precipitation of gold and silver from solution. The precipitation process, as applied to clarified leach solutions (less than 1 ppm suspended solids) at Pamour is called the Merrill - Crowe process. Precipitates from both milling operations are treated at Pamour's Area Refinery. Schumacher precipitates, unlike Pamour No. 1, require an ''Acid Treatment Stage"" prior to refining to remove the high contained copper. This is accomplished by leaching the precipitates initiallv with sulphuric acid to remove zinc and then with sulphuric acid and manganese dioxide to dissolve copper. Refining procedures after ''Acid Treatment"" are essentially the same for both precipitates.The following considerations highlight the basic principals applied to refining cyanidation precipitates at Pamour, including:"

Jan 1, 1986

By Ammar Henchiri, Godfrey McDonald

"Breakwater Tunisia S.A.’s Bougrine mine is located in a semi-arid region of Tunisia characterized with Triassic salt domes. Due to extensive agricultural land-use in the mine area, a zero-discharge tailings facility design and high water recycling rates to the concentrator were chosen to minimize the environmental impact to the surrounding area. The process water supply has an accumulation of naturally occurring salts due to high evaporation rates and the need to recycle 70% of the process water. The elevated salt content of the process water had an adverse effect on the efficiency of the flotation reagents, which led to the production of lower quality zinc concentrate.The impact of the water salinity on the zinc concentrate quality was documented by extensive laboratory testing. A feasibility study was prepared and a decision was made to install a reverse osmosis plant for desalination of the process water. A plant was constructed during 2000 which currently supplies up to 85 m3/hr of de-mineralized water, equal to approximately 45% of the total process water requirement. The salinity of the process water decreased from about ten to twelve grams per litre before installation to less than three grams per litre. Together with minor modifications to the concentrator circuit, Breakwater Tunisia has increased the zinc concentrate grade from 50% zinc to 55% zinc without compromising the zinc recovery rate of approximately 84%.This paper discusses the successful installation of a reverse osmosis desalination plant that allowed Breakwater Tunisia to improve the grade of the Bougrine mine zinc concentrate and thus increase the net smelter return.INTRODUCTIONBreakwater Resources Ltd., through a wholly owned subsidiary, Breakwater Tunisia S.A., acquired the Bougrine underground mine and related assets in September 1997. During the winter of 1997/1998, the company rehabilitated the mining equipment, modified the concentrator circuit, developed a new mine ventilation system and prepared a new mining production program. The mine was reopened on May 2, 1998 and was in commercial production as of June 1, 1998."

Jan 1, 2003

By K. Honkivaara, S. Junnikkala, J. Aho, K. Föhr, P. Lampinen

"Bubble area flux has been claimed to be a major tool to dimension flotation equipment. The paper describes laboratory scale (batch and 301 continuous cell using plant feed) and small-scale (1 ,8m3) industrial experiments with coarse-grained massive sulphide ore.Samples were taken with different froth thickness and air addition rates while the bubble size was measured with an UTC capillary device. Problems of averaging the bubble size measurements and the bubble area flux measurements are also discussed.Material balances were calculated using the commercial program BILCO. The flotation rate constants were calculated for pulp and for froth assuming that we can extrapolate the flotation rate constant of the pulp phase from tests using very thin froth thicknesses.The results indicate that the bubble area flux is not alone an adequate dimensioning tool. With fine sizes there was a nearly linear relationship between the bubble area flux and rate constant for constant impeller revolutions. For coarse sizes the form of the relationship is non-linear and seems to go through a maximum value. Thus the final flotation outcome is not a simple function of bubble area flux but depends on the particle size distribution and other more traditional flotation cell dimensioning variables. The effect of the froth residence time in the total recovery of coarse particles is large, but will not be treated in this paper."

Jan 1, 2000

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992

By E. Laatio, W. McKay

"History of Tara Mines Ltd.Tara Exploration and Development Company Ltd. was formed in Canada by Irishmen in 1953. The discovery of an orebody approximately six miles from the historically famous Hill of Tara in County Meath was a wild dream . Nevertheless this dream became a reality. Tara Mines Ltd. was formed, and the mine developed some 35 miles northwest of the City of Dublin in the Irish Republic.Tara&apos;s original drilling program indicated a zinc-lead orebody of approximately 60 million tonnes grading at 10.1% Zn and 2.6% Pb. The terms of the mining lease stipulated that the Irish government would acquire 25% equity interest in the operation. The mine was thus owned 75% by Tara Exploration and Development Company Ltd. of which the principal shareholders were Noranda and Northgate, together with 25% being held by the Irish government. The mine was purchased in March 1986 by Outokumpu Oy, a Finnish mining and metallurgical company, and together with the 25% government stake are the current owners. Outokumpu Analysis on Tara Mines Ltd.Upon ownership Outokumpu carried out a comprehensive analysis on the operation and came to the following conclusions :1. Tara had a good orebody;2. Tara had a skilled, capable, stable workforce;3. Tara&apos;s concentrator and processing equipment was adequate to meet requirements;4. Tara&apos;s mobile equipment fleet was too old and too numerousin numbers; and5. Tara had too many employees, both staff and hourly paid .With ore reserves of approximately 50 million tonnes and at a planned extraction rate of 2.6 million tonnes it meant that the mine had a lifespan of approximately 20 years. To be a viable operation into the future, the mine had to become more efficient. Operating costs and manpower levels had to be dramatically reduced."

Jan 1, 1989

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By Pavel Vasak

The Laurentian University Virtual Reality Laboratory (VRL) has provided a unique platform for the development and testing of novel seismic and microseismic data processing and visualization technology. In collaboration with Vale?s Creighton Mine, the technology was implemented at the mine site and consists of a VRL system and site calibrated Seismic Excavation Hazard Map (SEHM) software. The SEHM was developed as a practical solution for the mine operator to identify areas of elevated, active rock mass damage processes caused by recent mining activity. This paper is a pictorial representation of the 3D stereoscopic demonstration of the Creighton Mine seismic data distribution and interpreted SEHM for the first quarter of 2009. A live demonstration is scheduled at the Laurentian University VRL as one of the conference field trips. The demonstration highlights the technology transfer of research concepts into a near-real-time excavation hazard system that utilizes the key aspects of virtual reality technology; the ability to integrate large datasets (geology, mine excavation, (seismic) monitoring data, production scheduling, stress model, etc.); the ability to manipulate and visualize large datasets in both space and in time (mining sequence); and the ability to review the datasets by a group of experts in an immersive (3D stereoscopic), collaborative environment to better understand the processes and context of the mining-induced seismicity and evaluate potential risks to the mining operation.

Oct 1, 2010

By Brad Thrall

"Viceroy Resource Corporation of Vancouver, B.C. has recently developed the Brewery Creek Mine, an open pit heap leach gold mine 55km East of Dawson City in Yukon, Canada. Mineable reserves are 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797000oz) of gold. Ore processing employs the heap leach technology using run of mine ore. 1996 highlights included construction of 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1.46 gpt on to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting this mine has drawn significant attention because the heap leach technology, while proven in other jurisdictions, has not been used in Yukon where winter site temperatures routinely reach -45 C for extended periods.IntroductionFollowing a comprehensive governmental and public review of the proposed project, a Class A Yukon Water license was issued in August, 1995. Construction started in 1995 and leaching commenced in October 1996. The Brewery Creek Mine is in Yukon, the home of the Klondike Gold Rush nearly 100 years ago. This is the only part of Canada not glaciated in the Wisconsin advance so there is oxide ore resulting from about 80,000 years of weathering -unique in Canada. Discontinuous permafrost is present on site and has required special consideration in the design. Winter temperatures dip below minus 50 C, demanding an approach to mining and leaching that is different than in more temperate climates.Project DescriptionThe mine comprises 8 shallow, largely oxidized gold deposits along a 7km corridor. An 8 year mining program will extract 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797,000 oz) of gold. The strip ratio will be 1.35: 1. Overall gold recovery is projected at 78%. There will be 2.3 million tonnes of ore placed on the pad annually, with an average of 2.57 tonnes (83, 000 oz) of gold recovered per year. Because of the cold winters, the mine will operate approximately 210 days per year, while the leaching process will operate on a year round basis. Run of mine ore is placed on the heap 150 days per year. The recovery process utilizes conventional sodium cyanide leaching , carbon adsorption, caustic desorption, and on-site smelting. Peak employment during mining is 145 and winter staff is reduced to 45."

Jan 1, 1997

By B. K. Mishra, Avijit Biswal, B. C. Tripathy, Abhijeet Singh, K. Sanjay, T. Subbaiah

We studied theeffect of anode substrates such as pure lead (Pb), lead antimony (Pb-Sb), and lead-silver (Pb-Ag) on the structural and electrochemical properties of electrolytic manganese dioxide (EMD). X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and chemical analyses were used to determine the structural and chemical characteristics of the EMD samples. The charge-discharge profile was studied in 9 M KOH using a galvanostatic charge-discharge unit. In all the substrates the current efficiencies were more than 99% except with Pb-Sb where it was 90%. Results revealed the nature of the substrate strongly affected the morphology of the deposited material which in turn affected the electrochemical properties of the EMD samples. XRD analyses revealed that the nature of the anode did not affect the crystal structure of the deposited EMD and all the samples were predominantly ?-MnO2, which is electrochemically active for energy storage applications. The EMD deposited on lead substrate showed superior discharge capacity of 245 mAhg-1 when compared with other substrates.

Jan 1, 2014

By Gordon E. Agar, Brian Lyons, Gregory H. Styles, William B. Kipkie

"Rock rejection during the flotation of a copper-nickel ore was improved by adding carboxymethyl cellulose to both a rougher and cleaner flotation stage. The selection of the rock depressant was based on laboratory rates studies. Plant operating results are presented which confirm the laboratory selection of two particular brands of carboxymethyl cellulose.The rock assay of the concentrate was reduced from more than 40% to less than 15%.IntroductionThe traditional method of selecting flotation reagents relied upon batch bench scale tests, conducted under arbitrary conditions, to identify the effect of the reagent under examination. Too often these were ""one-off"" tests with little or no regard paid to the reproducibility of the results. Sophisticated researchers used statistical methods to design and evaluate the experiments but they were still obliged to rely on the arbitrary and often unreliable batch tests to generate the numbers that were analyzed statistically. An interesting side-effect of the enhanced sophistication of the statistical analysis was often that no significant effects would be uncovered in a series of experiments that would have generated many positive conclusions and much further experimentation if the same results had been evaluated by the traditional method.In the recent past, at least two groups of researchers a have directed their attention to the reliability of the batch experiments with a view toward improving the reproducibility of the test data. In this work the best of the improvements advocated by both of these groups have been adopted in order to generate kinetic data from batch tests that are as reproducible as possible.The objective of the work was to reduce the rock content of a bulk sulphide concentrate produced at Inco&apos;s Shebandowan mill. During 1982 the Shebandowan concentrate analyzed 3.5% Cu, 7.4010 Ni, 25% pyrrhotite and more than 40% rock, which resulted in an MgO content of 10.4%. Besides the expense of shipping all of this rock to Sudbury, the rock also contributed to the poor filterability of the concentrate. On favourable occasions the moisture content of the filter cake was slightly over 20% by weight. The magnesia content of the concentrate was deleterious to the reverberatory furnaces used by Inco for smelting nickel concentrate because the slag viscosity increased as the magnesia content increased, and the nickel lost in the slag went up."

Jan 1, 1987