Search Documents

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By R. W. Mei, R. A. Strombom, D. J. Moore

"Heat-shrinkable cable accessories are solving problems in the mining industry. This paper describes a range of products used by the industry, including low-voltage splices, high-voltage splices to 8.7 k V, cable repair sleeves, mining cable terminations used on system voltages up to 25 kV and motor connection kits up to 8 k V. Technical procedures and designs are illustrated.IntroductionThe development of high-performance heat-shrinkable materials slightly over 20 years ago proved to be one of the major technological breakthroughs in power cable accessories. Heat-shrinkable products were introduced initially for use as low-volt age cable accessories in the aircraft and electronics industry. A program of continuous development and product introduction now enables the manufacturer to offer a broad range of products for mining, industrial and utility electrical systems.With the advent of atomic energy, an important discovery was made-exposure of some plastic materials to high-energy electrons can cause the permanent crosslinking, or intermolecular joining, of adjacent molecules. Once the material has been crosslinked, it will not melt or flow at any temperature.The unique properties of heat-shrinkable products also result from the exposure of special thermoplastic formulations to high-energy electrons. Because of crosslinking, these products have perfect elastic memory. The heat-shrinkable products are supplied in expanded condition. When heated, they will shrink and tightly cover the object over which they have been placed. 'The functional and operating demands of mine cable accessories exceeded the classic electronic applications of heat shrinkable materials. These demands required a very sophisticated program to develop materials and adhesive systems that could endure the operational environment associated with the mining industry,Ease of assembly, low installed cost and operational reliability are among the main reasons for the acceptance of heat-shrinkable mine cable accessories in electrically powered mines. For over a decade, these systems have been demonstrating proven performance."

Jan 1, 1980

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By D. Allan Coutts

Demonstration projects using hydrogen as a fuel are becoming very common. Often these projects rely on project-specific risk evaluations to support project safety decisions. This is necessary because regulations, codes, and standards (hereafter referred to as standards) are just being developed. This paper will review some of the approaches being used in these evolving standards, and techniques which demonstration projects can implement to bridge the gap between current requirements and stakeholder desires. Many of the evolving standards for hydrogen-fuel use performance-based language, which establishes minimum performance and safety objectives, as compared with prescriptive-based language that prescribes specific design solutions. This is being done for several reasons including: (1) concern that establishing specific design solutions too early will stifle invention, (2) sparse performance data necessary to support selection of design approaches, and (3) a risk-adverse public which is unwilling to accept losses that were incurred in developing previous prescriptive design standards. The evolving standards often contain words such as: ?The manufacturer shall implement the measures and provide the information necessary to minimize the risk of endangering a person?s safety or health.? This typically implies that the manufacturer or project manager must produce and document an acceptable level of risk. If accomplished using comprehensive and systematic process the demonstration project risk assessment can ease the transition to widespread commercialization. An approach to adequately evaluate and document the safety risk will be presented.

May 1, 2007

By A. M. A. Mohamed, F. H. Samuel, S. Valtierra, H. W. Doty, A. M. Samuel

"The influence of Fe, Mn, Cu and Mg alloying additions, Sr modification and grain refinement on the microstructure of as-cast and solution heat-treated Al-10.8% Si alloys was investigated using optical microscopy and EPMA techniques. The results showed that the modification effect of Sr diminished with increasing Cu and Mg additions, due to Sr-Cu-Mg interactions. Strontium caused segregation of AlzCu in areas away from eutectic Si regions, and altered the precipitation sequence of the a-Ah5(Fe,Mn)3Siz iron intermetallic from post-dendritic to pre-dendritic, with the phase observed within the a-Al dendrites. Depending upon the alloy Fe and Mn content, a coarser variation (""sludge"") of the a-Fe phase occurred, in the form of polyhedral shaped particles. The AhCu phase dissolved almost completely during solution heat treatment, while Al5Cu2Mg8Si6, sludge, and a-Aln(Fe,Mn)3Siz phases persisted in all alloys, particularly at high Mg and Fe levels. The f3-Al5(Fe,Mn)Si phase dissolved partially in Sr-modified alloys, the dissolution becoming more pronounced after solution heat treatment."

Jan 1, 2006

By Åke Krukka, Heribert F. Broicher

"The iron ores of the Kiruna Mine in Sweden are of exceptional quality but for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998 LKAB has been testing prototypes of LIF Analysers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground the mining engineer supports the efforts of the metallurgist in the processing plant.INTRODUCTIONThe Kiruna Mine of LKAB, Sweden is the largest underground iron ore mine in the world. In the early nineties LKAB decided to develop the Kiruna orebody further down from the 775m main level to a new main level at 1045m. This development programme was realised while in the mineral processing section and in the pellet plant further capacity was added (Wyllie 1996).In addition to deepening of the mine, which opened up 330 million tonnes of ore, the exploitation of the so-called lake ore was included in the future planning, adding another 1 15 million tonnes of mineable ore. At an annual production of approximately 20 million tonnes of ore the Kiruna Mine today looks at a developed ore reserve sufficient for the next 20 years.All of the competitors’ ores traded in the world market are from open pit operations. LKAB compensates for the obvious disadvantages by continuous efforts to make the best possible use of her high quality magnetite ore deposit. This objective is realised by combined efforts in the pellet plant, the mineral processing plant and the mine. Propriety processes, latest big scale equipment and high tech solutions for automation lead to high quality sales products at a reasonable cost."

Jan 1, 2002

By Neil R. Burns, Michael Doggett

Abstract - The Nanisivik mine offers a unique opportunity to examine the economics of a mining scenario from its original feasibility study through to closure. In the early 1970s, the Strathcona Sound project (exploration around the Nanisivik mine) had advanced to the point where a significant mineralized body had been defined and a feasibility study was initiated. The study supported development of the Nanisivik mine, with government investment in regional infrastructure, and the mine was constructed and operated for 26 years. Many elements of the feasibility study were difficult to estimate because the project was unique in its high Arctic setting. As a result, many differences were found when comparing the actual mining data to the feasibility study. The majority of these differences were the result of an actual mine life of 26 years instead of the planned 12.5 years. Most of the mining costs were higher than estimated and production occurred at a much higher extraction rate than planned. On a constant dollar basis, the metal prices were, on average, below the feasibility estimates. For the most part, these differences balanced out, with the actual mining being only slightly more profitable than anticipated in the feasibility study.

Jan 1, 2004

By Oy Leuangthong

Red Dog mine is the world's largest Zn producer. The deposit consists of sulphide ore zones in sedimentary exhalative (sedex) deposits, and is characterized by the presence of multiple metals and multiple ore types. The objective of the case study is to characterize seven different minerals, Zn, Pb, Fe, Ba, sPb, Ag and TOC, within eight different rock types. Geostatistical models were constructed for each variable within the eight rock types, and subsequently assembled to give 40 realizations for six 25ft benches. The stepwise conditional transformation was used to account for the complex multivariate relations. In addition to reproducing the input data, histogram and variogram, the resulting models also respect multivariate relations locally and globally. This paper documents the methodology to construct these models. A thorough validation procedure was implemented. Comparisons with blasthole data show that the conditional simulations and the long-term models agree in expected value. The main advantages of the conditional simulations are (1) the explicit accounting of multivariate relations between the data in model construction, and (2) the ability to quantify variability and uncertainty at any scale. A small exercise comparing the profit from a kriged and a simulated model is also examined. Results show that the simulation approach showed a 3% increase in profit, relative to the conventional estimation approach.

May 1, 2004

By Walter S. Bergholz, Michael L. Schreder

"Since Escondida began operations in fiscal 1991, a series of aggressive expansion projects have enabled market share to be increased and ever larger profits to be realized. This was possible due to the very large size of the ore body and its high grade - averaging 2.7% copper from startup through fiscal 1997. The situation has now changed: ore grade is falling rapidly and is projected to be only 1.55% by 2003. Since revenue is directly proportional to ore grade, while costs are proportional to quantity of ore processed, profits will begin to fall dramatically. The Phase IV Expansion Project is intended to forestall this drop in profits by increasing ore processing capacity by over 85%.The Phase IV concentrator is designed for a nominal capacity of 110,000 MTPD and the key to achieving this value is through the proper design of the grinding circuit. This paper presents the general design criteria for the grinding circuit, as well as a description of the facility.INTRODUCTIONThe Phase IV Expansion Project consists of a new copper concentrator located 8.5 km south of the existing operations, a new tailings disposal and water reclaim system, a new concentrate slurry pipeline to the coast, and added concentrate handling capacity at the port of Coloso. The new concentrator has a nominal capacity of 110,000 tonnes per day (MTPD), compared to the existing concentrator’s capacity of 127,500 MTPD. The Laguna Seca concentrator is based on using the largest and most efficient ore grinding mills now available.The concentrator has been designed for a 110,000 MTPD nominal capacity. The process design criteria for the Phase IV project were established from in-house operating information and from test work. Unlike a green field project, Escondida already had an operating plant and it processes ore from the same pit that feeds the Phase IV plant. It is expected that the current mineralization will be similar for the first 6 years of operation of the new project. Therefore, some of the current plant operating conditions were incorporated directly into the design criteria."

Jan 1, 2004

By Leonardo Flores

"Minera Escondida operates two open pits on a porphyry copper district, southeast of Antofagasta, Chile. During 2005, ore will be delivered exclusively from one pit to two concentrators, while from 2006 both pits will provide ore to these plants. Annual testing programmes on drillhole samples, have allowed for the construction of hardness block models since 2000. These models have delivered two main hardness descriptors, the Bond work index and the SAG power index. These parameters and plant operational specifications have been used as input information to forecast, the expected throughput and ball mill product size (P80) for each block of ore. Two forecasting techniques have been used, an in house model, strongly dependant of bond work index and MinnovEx´s CEET2, dependant of Bond work index and Sag power index and other parameters. Model performance has been evaluated from reconciliating on a monthly basis, the forecasted throughputs against a recalculated plant throughput which accounts for losses in tonnage not caused by ore hardness but instead by unscheduled plant operation problems. The model performance for 2003 was ± 2% yearly and ± 5% quarterly, well within the expected ± 3% and ± 10%. INTRODUCTIONThe Escondida porphyry copper district is located 140 km SE of Antofagasta, Chile at 3150 m.a.s.l, at 24°16’ South latitude and 69°04’ West longitude (figure 1)."

Jan 1, 2005

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals in the hope of understanding the reasons for poor performance when it occurs, and developing mitigating strategies.This testwork along with a review of the relevant literature has demonstrated that the amount of sulphide added to the primary reactor, relative to the copper concentration, is the most critical parameter dictating plant performance, with pH and residence time important secondary factors. The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. Testwork shows that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. The theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are likely to experience growth in crystal particle size through aggregation rather than heterogeneous nucleation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process.There is evidence to suggest that operating the copper sulphide thickener in the SART Process without flocculants may be beneficial. Thickener underflow densities could improve from the current 10 - 15% range to 40 - 50%. This will not only reduce the flowrate of slurry to the filter, but the filtration properties of the slurry (filtration rate, filter cake moisture content) will also improve. This is one of the most critical engineering and design aspects of the SART Process, and the achievement of high solids density in the thickener underflow will not only improve the health and safety aspects of the operation, but also has the potential to lower capital costs and improve the quality of the final product."

Jan 1, 2016

By W. J. Witte, M. K. Witte

"The purpose of this report is to present a generalized preliminary design and cost estimates for a typical heap leach operation such as might be undertaken in Northern Ontario. This report should be of value to anyone in the mining industry planning, or contemplating, a heap leaching operation in Ontario, either on a large or small scale. While more detailed costing and design work will obviously be required for each specific project being contemplated, the data provided in this report should enable parties to make preliminary estimates of the costs of proposed projects and should identify most of the planning and design parameters that will need to be considered.Although heap leaching has been used extensively as a low cost gold recovery method in other parts of the world for many years, it has only recently become of interest to the Canadian mining industry.In order to investigate and demonstrate the feasibility of using heap leaching in Ontario, the Ontario Ministry of Natural Resources in 1982, undertook to locate a private sector proponent willing to undertake a 10,000 ton demonstration project. This project was to have been carried out at a production scale under normal northern Ontario field conditions. The Ministry was to have provided technical management and design for the designated project."

Jan 1, 1985

By J. K. Armstrong, C. Feyerabend

"As mines are constantly growing and expanding, so do the challenges for emergency response teams. They have to keep up with the pace set by current and future production techniques. Although mines have now reached depths of several kilometres and their dimensions and complexity are that of an entire city, mines rescue still must be able to reach the most remote areas within the mine in a swift and safe manner. The duration of breathing apparatus and physical human capabilities are limitations. Therefore, alternative methods have to be explored to extend the time under oxygen for mine rescue teams without putting additional stress on the team members. To address this global trend, Dräger, Goldcorp and PAUS have partnered to develop a mine rescue vehicle that allows mine rescue teams to travel for an extended period of time through a contaminated atmosphere without the use of breathing apparatus, thus extending the range of their mission. By applying currently available techniques, the safe expansion of mine production can be ensured, giving mine rescue teams the ability to respond to accidents in a safer and faster way. INTRODUCTION With the reduction of easily accessible natural resources, there is a global trend toward searching for higher ore grades underground and/or continually expanding mines underground to extend their lifetime. While in some areas this trend has just begun, in other countries mines are reaching depths or horizontal dimensions that pose extreme challenges (Codelco, 2016). These challenges include safety relevant topics, such as rock stability, heat and seismicity, but also more basic issues such as distances to the working face, which can become crucial considering the cost to develop a new shaft or decline. To overcome this, there is a growing interest in collaboration among various stakeholders to drive the development and support of deeper mines and tackle the complexity of underground mining. This is evidenced by the fact that several industry and research groups and networks have formed, e.g. the I2mine project in Europe and the Ultra-Deep Mining Network by the Centre for Excellence in Mining Innovation in Canada. Due to commodity pricing and the trend toward renewable energy, metal/non-metal mining will be the driving force behind this development."

Jan 1, 2019

By A. -M. Lafront

The corrosion resistance of die-cast and freely-solidified and electromagnetically-stirred thixocast AZ91D alloy has been studied using electrochemical noise technique in a 0.05M NaCI solution at pH 6.1 and 25°C. Specimens polished at different depths were immersed for a period of 75 min in order to assess the influence of the microstructure on corrosion kinetics and morphology. At depths between 10 and 50 µm (skin), all specimens showed general non-uniform corrosion with the lowest corrosion resistance. Between 100 and 200 µmn (interior skin), the observed corrosion was accompanied by superficial undefined pits due to metastable pitting. The corrosion form for 100-200 µm gave the best corrosion resistance. Stable pitting corrosion was observed beyond 400 µm deep on the bulk specimens. The skin of all thixocast specimens prepared billets showed a more corroded surface than that of die-cast. The interior skin as well as the bulk specimens showed better performance than that of the die-cast specimens.

Jan 1, 2007

By Barbara Hendrickson

Outline ? Canadian Regulatory Update ? Turning the Corner: Background & Status ? Implications of U.S. Waxman-Markey bill for Canada ? Federal-provincial considerations ? Current certainties and uncertainties ?Turning the Corner? as Originally Proposed ? April 26, 2007 - the Canadian federal government announced Turning the Corner: An Action Plan to Reduce Greenhouse Gases and Air Pollution (?Turning the Corner?)

May 1, 2009

By Peter White

Mine Planning Shaft Collar Shaft Sinking Raises Ramp Underground Water Storage

May 1, 2009

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016

By W. A. Lang

COAL of sub-bituminous rank underlies much of the plains area of Alberta. This coal is geo-logically young, and occurs in Belly River and Edmonton strata of Up-per Cretaceous age. Generally, the seams are flat-lying, but in some areas they may dip as much as 5 degrees. The overburden, composed mainly of glacial clays and sand-stones, may vary in depth from a few feet to several thousand feet. Recovery of the coal has 'been by drift, slope, and shaft underground mines, and by open-pit stripping operations. Production has been obtained from a large number of mines, most of which have been relatively small and with preparation equipment limited to a loading tipple with screening facilities, and a picking belt where high-ash materials can be removed from the larger sizes. The coal has been sold for domestic and industrial space-heating, for production of process steam, and for power generation. In re-cent years competition from natural gas, propane, and oil has seriously interfered with the production and marketing of sub-bituminous coal, especially with the disposal of the smaller sizes at a realistic price.

Jan 1, 1958

By Michael B. Cortie

Mesoporous gold sponge has the unique property of being both metallic and highly resistant to oxidation. It has potential application in catalysis, in bio-sensors, in optical coatings, in analytical chemistry and, as we show here, as the basis for a new kind of ultra-capacitor. Due to the cost of gold, the most probable niche for a gold-based ultra-capacitor would be in the high-power/high-energy regime, a region where gold would compete with devices based on RuO2. A high internal resistance limits the power that can be usefully drawn from existing carbon-based ultra-capacitors, and that this problem can potentially be overcome by gold-based devices. A simple proof-of-concept ultra-capacitor based on mesoporous gold is described and its behaviour during charge and discharge cycles examined. In this work a step change in the input or output voltage of the device was used as the controlling parameter. There was also a residual faradaic current resulting from traces of undissolved aluminium left over from the AuAl2 precursor used to make the sponge, and some charge storage due to polarization of the solution. Deconvolution of these three effects was not entirely accomplished, but an ostensible capacitance of about 7 to 14 mF/g Au was demonstrated. Further improvement from these early results seems likely.

Oct 1, 2003

By Son Hye Jin

Abstract ? KHNP is participating in the construction of Nuclear Power Plant both in Korea and UAE. ? We want to improve our construction project management process. ? So we are now developing the process model on nuclear power plant construction management. ? For the effective adoption of this process, we are planning to develop IT system. ? For the first step, we were established the Information Strategy Plan

Aug 1, 2013