Search Documents

By C. H. Madsen

THE Hard Rock gold mine is in the Little Long Lac mining area, Thunder Bay district, northwestern Ontario. It is four miles by road from the town of Geraldton, which is on the Canadian National railway, 180 miles northeast of Port Arthur. The original discovery of gold-bearing quartz veins on the property was made in 1931. Shaft sinking began in the fall of 1934 and approximately 7,400 feet of lateral development on four levels was completed. In 1935, further discoveries were made half a mile west of the early workings, and the No. 2 shaft was sunk in this area in a porphyry zone. In January, 1938, a 20C-ton cyanide plant was completed and began drilling ore from the gold-bearing porphyry orebody. The daily feed was increased gradually to 300 tons in the next six months and a recovery of 97.5 per cent was effected. During the summer of the same year, a new and larger orebody was discovered to the north of the porphyry zone. It occurs in a band of iron formation and contains a high percentage of pyrite and arsenopyrite. Extensive tests were rr.ace on this sulphide ore in the Mines Branch ore dressing laboratory at Ottawa, in the laboratory of Canadian Industries, limited, at Toronto, and later at the mine, to find a suitable method of treatrr.ent. As a result of this research, a Potation plant was added to the original cyanide mill and on November 7th, 1938, differential flotation was used to separate the pyrite from the arsenopyrite fraction of the ore. The pyrite concentrate was re-ground and cyanide:l, and the arsenopyrire concentrate was stored for subsequent treatment. Differential flotation was discontinued in April, 1939, in favour of bulk formation of all the sulphides, and the whole cyanide residue was stored. On March 15th, 1939, a 10-ton pilot roaster was completed and rests were conducted on the arsenopyrite concentrate and the bulk concentrate. The results obtained led to the building of two roasters of the same type, large enough to roast all the concentrates. These roasters were put in operation on September 24th, 1939, and the calcines were cyanided in the original circuit.

Jan 1, 1941

By T. Fekete, D. L. Flocks, R. T. Hart

The plugging effect of bacteria was investigated by injecting various concentrations of dead bacteria cells though sandstone cores. Pressure profiles along the cores were recorded periodically during the injection cycles. The plugging effect was analyzed using a plot of the ratio of reduced permeabilities to the initial permeability versus input volume. Results indicated that Tock permeability has little effect on plugging, but that the concentration of bacteria in the injection water has a significant effect on plugging characteristics. The pressure profile curves showed that bacteria penetrated several inches through the core but that the greater portion of the bacteria accumulated at the in-put end of the core.

Jan 1, 1960

By B. R. List, E. R. F. Lord

The Syncrude open pit mine, located near Fort McMurray in northeastern Alberta, produces approximately 410 000 tonnes of oil sand feed daily, which, after undergoing a bitumen extraction phase, generates approximately 315000 tonnes of tailings solids daily. The tailings are used to hydraulically construct containment dykes and supporting beaches of the storage facilities. Tailings deposition commenced in May 1978 with the commissioning of the Mildred Lake Settling Basin which is currently composed of approximately 600M m3of solid sand approximately 300M m3of contained fluids with fine tailings in suspension for consolidation. Two other storage facilities, commissioned over the past six years, have been developed to store sand and consolidated fine tailings referred to as mature fine tailings. Fine tailings reduction initiatives being developed will be successful in reducing future production of fine tailings volume by 20%. These initiatives include spiking (addition of fine tailings to coarse tailings lines for deposition), composite tailings (addition of gypsum to promote consolidation) and freeze/thaw dewatering, also to promote consolidation. The mandate of research efforts is to enhance tailings disposal and to develop economical and technically feasible reclamation initiatives. Final tailings landscapes will be geotechnically stable and ecologically productive to minimize or eliminate long-term liability. This technical paper will review the design philosophies of the current facilities and provide an overview of the areas of continuous improvement in the field of tailings management practices through the concerted research efforts and their implementation.

Jan 1, 1997

By R Chandramohan

Comminution is the science of size reduction of brittle materials. It is integral to mineral extraction and is one of the most energy intensive processes in the mining industry. There are a number of tests used to quantify the strength of ore, which are then used to size the AG / SAG mill in circuit design. The calculated energy utilized for breakage in these devices is based on the assumptions that the materials treated are of average shape and that the processing equipment is designed to break the ore as efficiently as possible under the given operating conditions. In drop weight tests, it was found that shape significantly influences the measured rock strength. Controlled experiments with variations in blends of rock shape show that mill throughput increases with the addition of weaker shaped rocks.

Jan 1, 2012

By N. Pajunen, R. Mäkikoskela

"The current state of environment has been achieved by acting linearly. At the same time, we know that transition towards circular economy cannot be made the same way that we have used to, trusting only a market economy and economic growth. Environmental improvements have been promoted, some progress has been made, but major steps towards sustainability have not been taken. Industry is now facing significant change, from process related environmental thinking to product-based environmental thinking.Engineers make decisions which have lifelong influence and even longer on environment and society. Material engineers in case of saving natural resources and increasing material cycle, have an important role to play in the transition towards sustainability. Best knowledge of minerals and materials is in the material development phase. If we want to increase the cycle of different materials, it is vital to make decisions towards circular economy in early phase of product´s life cycle.The target of this study is to promote circular economy; to increase material efficiency; to save natural resources; and to extend product lifecycles in process industry via product design and material development. In this study we have a new kind of cooperation. We combine two disciplines, engineering science and fine arts. We promote sustainability via breaking out the silos. We bring the cyclic artistic thinking into engineering science and environmental research. The new research combination makes the existing information visible in a new way, and it will change attitudes and ways to act by means other than traditional linear rationality.We have tested the new working method via the industrial case study with the chosen product: the sandwich panel of construction industry. The target of the study was to create something new from the chosen product with artistic thinking. The working method will be presented in this paper."

Jan 1, 2016

By L. P. Srivastava

Rock bolts have been used since long to enhance the shear strength response of jointed rocks in civil and mining engineering structures. However, the assessment of strength response of a rock mass reinforced with rock bolts remains an unresolved problem till date. In the present article, an attempt has been made to study, through physical model tests, the shear strength enhancement of a blocky mass due to provision of passive rock bolts. Direct shear tests were conducted on large specimens of size 750 mm x 750 mm x 900 mm of rock mass under a normal stress varying from 0 to 2.0 MPa. Concrete was used as a model material to simulate intact rock and, elemental blocks of size 150 mm x 150 mm x 150 mm were used to form the mass specimens. Steel bolts of 6 mm diameter with 2 mm thick grout were used to reinforce the mass. Three different configurations of bolts were adopted. Observations were made on shear stress, horizontal shear displacement, and dilation during the tests. Effect of normal stress and reinforcement on peak shear stress and shear stiffness was studied. It is observed that the rock bolts enhance the shear strength of the mass by preventing sliding along the shearing plane, and by inducing additional normal stress due to tension mobilized in the bolts. The rock mass, therefore, becomes stronger due to the high degree of interlocking produced by the bolts. Shear strength of the mass increases with increasing numbers of bolts. In the case of reinforced mass, the enhancement in shear strength due to provision of bolts decreases with an increase in normal stress. The provision of bolts improves the cohesion of joints substantially. The effect on friction angle is low. The shear strength enhancement depends on the area of the bolts, spacing of the joints, spacing between the bolts and the cohesion of the intact material. A correlation has been established using which the enhancement in shear strength due to the provision of bolts can be assessed.

Jan 1, 2015

Vast quantities of cosmic material, ranging in size from fine dust to large meteorites and planetoids, have been colliding with and accumulating on the earth since its origin 4.5 billion years ago. There are less than twenty well preserved meteorite craters and Jess than thirty fossil craters or astroblemes on the present face of the earth. On the moon, there are approximately 200,000 craters on the visible face alone -the largest crater being 132 miles in diameter and attaining a depth of 16,000 feet. Making allowances for the different physical conditions on the moon and assuming that these lunar features are of impact origin, the indifference is that, since primeval time, large numbers of celestial objects have also encountered the earth, but that both the topographic expression of the impact and the objects themselves have been destroyed by weathering and erosion. It may be reasonable to suggest that additions of cos-mic bodies have materially altered the chemistry of the earth's crust from place to place and that the impact of large meteorites and asteroids has created zones of weak-ness in the crust that could be the center of magmatic intrusion and mineralization.

Jan 1, 1965

By Harry R. Oldale

This paper first covers the general and economic geology of the Coxheath Hills area, and then outlines the exploration and mining development that has been carried out since the first discovery of copper in the area in 1875. The work of Mariner Mines Limited from 1963 to the present time is detailed, particular attention being paid to the recent discoveries of copper, silver and lead mineralization that have greatly enhanced the potential of the area.

Jan 1, 1967

By H. Wilton Clark

"IntroductionTHE CANADIAN use of short-period delay-action detonators in coal shooting has been carried on for about two years, mostly in British Columbia, and this is a preliminary report on progress to date. Entire coal faces are being shot successfully with one application of electric current.The electric blasting cap came into use about the beginning of the century. The low-tension electric cap, the type most commonly used, consists essentially of a metal tube containing an initiating explosive. Two wires lead into the end of the cap and are connected inside the cap with a short 'bridge wire .of very high resistance. This •bridge wire is buried in a match-head of a readily ignitable powder composition. When current goes through the lead wires, the bridge wire becomes extremely hot and sets• off the match-head which, in turn, ignites the powder just below it in the tube. This explosion sets off the main charge of explosive. Thus, by connecting a group of caps to a source of electric .current, a number of charges could be exploded simultaneously. This immediately became of great value to mine and quarry operators. Explosives could now be used to break up large masses of material at one time, as against the older, slow method .of blasting small amounts with single charges.The next step was to develop a delay detonator which would allow charges of explosive to fire one after the other, one or two seconds apart. Such detonators allowed first blasts to relieve some rock burden before the next charge fired, giving the second charge an easier task in forcing out more rock, and so on for the rest of the series of charges."

Jan 1, 1953

By R J. Tremblay, R. R. Hoffman

This paper deals with materials of construction and problems encountered and overcome in leaching and filtration of oxidized sulphuric acid slurry in the Port Radium mill after eight years of operation. The slurry is characterized by a high calcium sulphate content as well as a high chloride level under oxidized conditions, both of which affected initial design and subsequent changes. Leach agitation tanks are of wood with a mild steel superstructure and stainless steel agitator and moving parts below solution level. Electro-polished 316 stainless steel cooling coils are used for temperature control of the slurry. The string filters are of the Oliver type with wood decking. Extensive use is made of wood, Linatex lined mild steel and stainless steel for the slurry handling. A typical analysis of the slurry solution follows:(pH-1.30) ClOa Fe+++ Free Acid UaOs c1-so.--0.10 gms/litre 10.2 gms/litre 6. 7 gms/litre 3.5 gms/litre 2.0 gms/litre 155 gms/litre

Jan 1, 1961

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

By J. Lapointe, S. Leger, D. Proulx

"Une méthode non-électrolytique est utilisée pour plaquer au cuivre la fibre d&apos;amiante chrysotite. En variant les paramètres de placage du bain, on détermine les conditions optimales du taux de deposition du cuivre . Une analyse par diffraction aux rayons-X permet une comp araison relative des résultats de placage et de précipitation d&apos;oxyde cuivreux dans Ie bain. Le traitement de placage a pour but d&apos;assurer une adhésion suffisante de la fibre dans une matrice métallique Iors de la fabrication éventuelle de materiaux composites.IntroductionCette communication se veut un compte-rendu de nos travaux sur Ie placage au cuivre de la fibre d&apos;amiante chrysotile, en vue de I&apos;incorporer éventuellernent dans une matrice métallique. La fibre d&apos;amiante est constituée de fib rilles élementaires d&apos;un diamètre d&apos;environ 0.02 um qui ont une résistance en tension de I&apos;ordre de celie de la fibre de verre ou de carbone(1). Pour être efficace, la fibre de renf&apos;ort d&apos;un matériau composite doit d&apos;une part, avo ir des propriétés mécaniques intrinsèques élevées, et d&apos;autre part, adhérer solidement â la matrice pour que Ie transfert de charge s&apos;effectue sans qu&apos;il y ait décohésion entre les composantes du matériau.La fibre d&apos;amiante étant naturellement soyeuse, il faut la traiter superficiellement pour que l&apos;adhésion avec la matrice soit suffisante. Ainsi, on recouvre la fibre de phénol-formaldéhyde(2) ou de silane(3) lorsqu&apos;elle est employée avec une matrice polymere. Dans Ie cas d&apos;une matrice métallique, ces dépôts organiques ne peuvent resister aux températures de mise en oeuvre, d&apos;où l&apos;intérêt de plaquer les fibres par un dépôt métallique.Dans cette étude, nous rapportons les résultats relatifs à la methode utilisée pour plaquer au cuivre la fibre d&apos;amiante chrysotile. Une analyse par diffraction aux rayons-X permet de comparer les différentes conditions de placage non-électrolytique."

Jan 1, 1985

By J. G. Stevens, S. W. Colley

"Selective separations of metals and ions in mineral extraction and refining are becoming more challenging as ore bodies become more complex and environmental pressures increase. The separation and containment of mercury produced in gold mining are a factor in the profitability and operability of mines. This paper will discuss the development and implementation of the Johnson Matthey HgFree selective mercury removal process. The process is designed to selectively recover co-leached mercury from either heap leach pregnant solutions at ambient temperature and low mercury concentrations, or electrowinning pregnant solutions at elevated temperature and high mercury concentration, without affecting gold or silver recovery. The process utilizes a highly selective adsorption-desorption step in which mercury is removed quantitatively by the HgFree adsorbent without adsorption of gold, silver or other metals present. Development of the original HgFree adsorbent has resulted in a process whereby mercury can be recovered as an inert salt and is never present as the free metal. The HgFree adsorbent can be regenerated and recycled in situ, and is capable of being reused multiple times. The overall process is compatible with existing gold mining and recovery practices and offers significant environmental and sustainability benefits, including reduction or elimination of the need to retort mercury with a subsequent reduction in potential mercury air emissions. Development of the HgFree adsorbent and process will be discussed along with a pilot operation at two operating mines.INTRODUCTIONMany gold ore bodies contain high concentrations of mercury which when extracted with cyanide, co-extract with the gold and other metals. This mercury is carried through the process with the gold, posing environmental and technical issues when it is separated from the doré. This paper describes a method to selectively adsorb mercury from the gold recovery circuit while it is in a soluble form, leaving gold to be processed as normal. The removal of mercury from the circuit eliminates the need for mercury retorting of doré and so reduces the potential environmental impact of fugitive emissions of elemental mercury."

Jan 1, 2016

By Freislich. M., Y. Gordon

"In the changing global market scenario for raw materials for the steel industry, a number of novel iron- and steelmaking process technologies are being developed to provide the steel companies with economically-sustainable alternatives for iron- and steel-making. In addition, the steel industry is also focusing on reduction of energy consumption as well as green-house gas (GHG) emissions to address the crucial subject of climate change. In this context, it is important to assess these critical issues for the alternate iron- and steelmaking technologies that have been developed. This paper presents a comparative evaluation of energy-efficiency and GHG emissions for some selected iron- and steelmaking technologies that are being considered for implementation. In this work, Hatch’s G-CAP™ and En-MAP™ tools that were developed with the main objective of quantifying and qualifying the potential energy savings and CO2 abatement within the iron and steel industry, were employed in the evaluation conducted. INTRODUCTIONThe iron and steel industry continues to transform itself and evolve in the ever-changing global market place – the raw material scenario is constantly changing with respect to quality and quantity (availability), there is stiff competition in both global and local markets, and there is increasing pressure to address global climate change issues, especially since the steel industry is highly energy- and carbonintensive. There is growing importance of steel production in developing countries such as China and India – this means that the steel industry in these countries will play an important role in defining and shaping the future of the industry.Climate change is expected to present new risks to the steel industry with respect to ensuring a sustainable business. Legislators are proposing to limit GHG emission by placing an implicit price on CO2 emission - market-based “cap and trade”, carbon tax etc.. In this scenario, it is important for the steel companies to reduce exposure to climate-related risks and at the same time, find business opportunities within these risks. Thus, there is a need to strategically manage the climate change risks; the key steps to strategically manage climate change risks are presented in Table 1[1]."

Jan 1, 2012

By William Ferguson, Claude Deveau, Wade Hazel, Stephen R. Young, Allen Lussier, Robert Copeland

"LocationSometimes known as the Bernie Lake mine, the mine is located about 180 km east-northeast of Winnipeg on the northwestern shore of Bernie Lake, close to the Nopiming Provincial Park and the Manitoba-Ontario boundary. The mine is accessed from Lac du Bonnet which is linked to the provincial road system.Brief Description of OperationTantalum Mining Corporation of Canada Ltd. operates an underground mine employing ramp access, room and pillar mining, and shaft hoisting for the production of tantalum, lithium and cesium minerals. Daily campaigned crushing of the tantalum and lithium ores supply separate concentration circuits. Tantalum recovery employs conventional gravity equipment together with recently developed centrifugal concentration methods. All tantalum concentrates go to Cabot Performance Materials for the production of tantalum chemicals and metal. Lithium minerals are recovered using heavy medium separation and silicate flotation to produce spodumene and montebrasite/amblygonite concentrates. The lithium concentrates are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock for the recently built on-site chemical plant dedicated to tl1e production of cesium formate, a high-density drilling fluid for use in the oil industry."

Jan 1, 2000

By F. Bourgeois, J. -S. Kroll-Rabotin

ABSTRACT: Falcon concentrators are enhanced gravity separators designed for concentrating fine particles. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidization water. We investigated the physics of particle transport inside Falcon concentrators, and concluded that separation efficiency is governed by differential settling velocity. We derived and published a predictive model of the partition function under dilute conditions. We intend to extend the initial model to concentrated ultrafine suspensions for application to industrial scenarios by adding hindered settling to account for solid concentration effects.

Jan 1, 2011

By M. Jiang, X. Fan, W. X. Chen, Z. K. Guo, H. H. Zou

"Some improvements are carried out for elasto-plastic model by taking the shear dilation effects and relaxation effects of deep rocks into accounted. The high pressure equations of states with Mie-Grüneisen form are also introduced to describe the relation of pressure-volumetric strain. Numerical simulations of free field responses for deep underground explosions are conducted by using the user subroutines which compiled by means of the secondary development functions of LS-DYNA9703D codes. It is indicated that the dynamic responses of free field are well simulated based on this improved elasto-plastic model, and the analytical results are in good agreement with the data of U.S. Hardhat nuclear test.INTRODUCTIONDynamic behaviors of deep rocks for underground explosions are obviously different from that of shallow underground explosions and have aroused great attentions of international experts who work for rock engineering. The dynamic models of deep rocks could be roughly divided into classic elasto-plastic model and fracture damage model according to different theoretical foundation. M. E.Kipp and D. E.Grady et al. are the outstanding representatives who engaged in the researches of fracture damage mechanics. Researches of dynamic problems for geomaterials were carried out by C.C.Grigorian and the conclusion that incompressible elasto-plastic medium model could not be used to solve the problems of closed underground explosion was derived, and therefore C.C.Grigorian model was proposed. In this model, C.C.Grigorian assumed that the average hydrostatic pressures and the densities of medium had one to one relationship, and the path of loading or unloading is different from each other. For shear deformations, analytical solutions of the problems were derived according to the model which was slightly different from Prandtl-Reuss model, the constitutive equations were closed by Mises-Schleiher constitutive model. However, the analysis showed that there were two inadequacies in C.C.Grigorian model. Firstly, the shear dilation effects of fractured medium after wave front could not be considered. Secondly, the relaxation characteristics of the rocks in fractured region were not taken into account."

Jan 1, 2015

By P. A. Peach, W. H. Gross

The modern economic geologist in Canada is well equipped to apply geological, geochemical or geophysical techniques in the exploration for ore. Recently, great advances have been made in geophysics and geochemistry, and a large number of new orebodies have been discovered by these methods. An attempt is made in this paper to show that there has also been a considerable advancement in geological knowledge and that the most effective application of geophysics and geochemistry often occurs in areas already considered geologically favourable for the occurrence of ore. Ali exploration methods sooner or later suffer from diminishing returns. Therefore, as time goes on, one can expect to see the application of some of the more subtle or refined geological techniques that are presently being developed.

Jan 1, 1967

By Anthony A. Zoobkoff

Gotcha! ? What Did I Just Agree To? ? You can?t repeat or use anything you heard. ? Did you agree before you knew what you were going to be given, told or shown? ? If you knew what you were to be given, told or shown, would you have still agreed?

May 1, 2013

By H. Lazreg

This paper presents an evaluation of surface resistivity techniques as a tool for delineating salt-water intrusion in Shippegan, N.B. The study consisted of resistivity profiling, resistivity soundings and a limited number of induced polarization soundings in selected areas in the Province of New Brunwick. The results from resistivity profiling indicate that when seawater intrusion occurs in a sandstone formation the resistivity contrast is sufficiently large to allow a precise delineation of the intrusion. A formula is then derived to convert resistivity values to chloride concentration in the "cone of intrusion". The results from resistivity soundings showed that shaly formations may have resistivities as low as seawater-contaminated sandstone. An indeterminacy has resulted from this resistivity overlap. A limited number of IP soundings were performed in an effort to resolve it. The results showed that IP can be of appreciable help in resistivity interpretation.

Jan 1, 1972