Search Documents

By Rodrigo Craig Cerello

The Brazilian economy has always presented a strong correlation with the mineral activity. Since colonization days, due to the territorial expansion caused by the explorers search for gold, mining in Brazil became a basic sector of national economy. Currently, the Brazilian mineral sector¹ estimates a 550% production increment (Figure 1A) in the last 10 years, reaching the US$ 50 billion value, reflecting the increased global demand for raw materials from mineral origin. According to the Brazilian Constitution², mineral resources belong to the Federal State and, consequently, their exploitation must be authorized, under penalty of engendering federal crime. Furthermore, activities of this nature are prone to cause environmental degradation such as, but not limited to, deforestation, pollution, soil deterioration and water contamination. The GPEMA represents the forensics group of the Brazilian Federal Police responsible for the technical analysis of traces related to crimes against the environment and consequently, illegal mining cases.

Aug 1, 2013

By E. G. Baltuch

Natural Ventilation in mining and metallurgical processing applications is key to proper operation function. There are number of ventilator designs available to a project team or design engineers, the selection of which will affect both the type of building structure required, project costs and design performance which is difficult to rectify or re-engineer once implemented. Research and applied results, such as that performed by Air-Therm Inc., demonstrates that computational fluid dynamic simulation allows for 5 dimensional observation, analysis and optimization at significantly lowered cost than previously possible. These results have been fully implemented on a number of mining and metallurgical applications and the company continues to study, optimize and innovate as new tools become available to provide the best possible engineered solutions for particular applications.

Aug 1, 2013

By G. F. Trainor

The complex ore body at CNRL?s Horizon mine presents some unique challenges in managing ore and waste delivery. With 25m x 25m ore blocks shovels often take bucket loads from multiple blocks to fill one truck load. With CNRL monitoring 22 different qualities per material a precise calculation of the blended quality of ore on the back of each individual truck is essential to meet the daily blend requirements at the plant. Additionally, one of these qualities must be closely monitored and controlled at a singular level as delivery of certain grade and quantities can cause serious disruptions at the plant. The waste material also requires special handling and delivery for its use in dyke construction for tailings impoundment. Shale materials used in the construction contain high levels of saline that must be contained to prevent seepage into ground water. This paper will discuss how the use of Wenco?s survey-grade GNSS system on shovels, its dispatching algorithm, and fleet management applications give CNRL the ability and confidence to control and report on these three issues.

May 1, 2013

By Marcel Vallee, D. C. Gagnon, C. CARBONNEAU, P. ST-JULIEN

The Magdalen Islands archipelago, a cluster of fifteen islands, is located near the centre of the Gulf of St. Lawrence on the thickest portion of the Carboniferous Fundy Basin of the Maritime Pro vinces. The bedrock of the Magdalen Platform includes a thick succession of evaporites of Visean Age, occurring as a series of thickenings, ridges, domes and diapirs reaching a probable vertical thickness of close to 6000 m. The emplacement of 1hese salt structures by flowage has much dislurbed 1he SlrOligraphic sequence of the rocks of the Windsor Group, particularly 1he Havre-aux-Maisons Formation. Subsequent tectonic movemenl has broken the overlying Cap-auxMeules Forma1ion info an assemblage of panels and blocks now slightly tilted. Following detailed gravimetric surveys and more than 30,000 m of diamond drilling, SOQUEM has discovered, at various dep1hs, seven salt domes on four of 1he main islands of the archipelago. These evaporite bodies generally are localized near the cemre of complex anticlinal struclUres where diapiric movements and faulting have disturbed the original stratigraphic succession. At Rocher du Dauphin near Grosse 1/e, in 1he northern part of the archipelago, Seleine a SOQUEM subsidiary is developing a mining complex with an annual capaci1y of 1,250,000 1onnes of deicing salt for 1he Canadian and Eas1ern United Swtes marke1s. The stan of operations is scheduled for April 1982.

Jan 1, 1984

By Hooman Askari-Nasab

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. The objective of the mine plan is to maximize the future cash flows within the technical and physical constraints. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. In the MILP formulation the slope constraints guarantee that all the overlying blocks are mined prior to mining a given block. Traditionally, the slope constraints have been modeled with cone templates representing the required wall slopes of the open pit mine. The overall pit slopes constructed by these templates are a function of the width and height of the geological block model. Therefore, the overall slopes are fixed in one bearing. This paper presents a general MILP model for open pit mine scheduling with variable slopes constraints. The methodology utilizes a directed graph to capture the precedence of extraction of blocks and pit slopes in different bearings. Depth-first-search algorithm was used to traverse the graph for constructing the slope constraints in the MILP problem. TOMLAB/CPLEX was used as the implementation platform to efficiently integrate the mathematical solver package CPLEX with MATLAB. A case study on intermediate scheduling of an iron ore mine over twelve periods was carried out to validate the models.

Oct 1, 2009

By D. C. Fraser, W. J. Scott

"Airborne electromagnetic surveys were flown during 1965 in the Moose River area of Ontario. The systems used were INPUT Mark II and the Canadian Aero Otter. Anomalies indicated by both systems were located on the ground with vertical-loop EM. Two such anomalies were drilled, with no explanation being found in the bedrock geology. Subsequent seismic, resistivity and gravity surveys indicated that the sources of these anomalies lay in the overburden. Current work in the similar geological environment of the Winisk River area has shown that comparable AEM anomalies can still be misleading. The lesson to be, learned from these experiences is that additional geophysical work can help to resolve doubtful cases before drilling decisions are made."

Jan 1, 1973

"Successive seismic waves may cause progressive weakening of a fault zone, which has been recognized as the mechanism of earthquake aftershocks. However, it is unclear that how a fault zone slips under each wave cycle and how slip displacement accumulates under continuous wave cycles. This laboratory study provides direct evidences on the slip process of a simulated granular fault zone dynamically induced by an incident wave without the effects of late-arriving and reflected waves. The experimental observations show forward and backward slip paths of the fault zone and partially recovered slip displacement after a wave incidence. The unrecovered slip displacement after each wave cycle can be accumulated until it reaches a critical slip distance for seismic faulting, which may reinterpret delayed triggering in earthquake dynamics. The limited interseismic period restricts fault self-healing in strength. The experimental results also indicate that the dynamically induced frictional slip on the fault zone is associated with a complex frictional system, including seismic wave radiation, frictional slip initiation and normal stress vibration. Different from the dynamically induced frictional slip on the fault zone, the statically induced frictional slip causes a permanent increase of slip displacement along the shear loading direction. INTRODUCTIONAn earthquake mainshock may induce aftershocks by suddenly changing external stresses applied to another fault zone in the near field (Kilb et al., 2000) and by slightly perturbing a fault zone from a critical steady state to stick-slip faulting in the far field (Gomberg and Davis, 1996). The dynamically induced frictional slip on a fault zone has been recognized as the mechanism of earthquake aftershocks (Marsan and Lengliné, 2008; van der Elst and Brodsky, 2010). Although earthquake aftershocks have been extensively studied by many seismological methods, a simplified laboratory fault zone can provide possible interpretation on real faulting and detailed analysis on a friction process (Dieterich, 1979; Nielsen at al., 2010). According to a few laboratory experiments related to the dynamically induced frictional slip on a simulated fault zone (e.g., Uenishi et al., 1999; Johnson et al., 2012), the slip process induced by successive seismic waves exhibits continuous motions. However, it is unclear that fault slip response under each wave cycle and slip displacement accumulation under continuous wave cycles."

Jan 1, 2015

By Marko Lampi, Ross Andrews, Jouni Pihlasalo, Robert Matusewicz

With widespread discussion on reducing carbon, sulphur and other emissions, use of sustainable energy sources and the pivotal circular economy theme, consideration needs to be given to pyrometallurgical operations broadly and more specifically, non-ferrous metallurgy. These themes present a number of challenges in terms of current operations and the view of processing the metals which are largely taken for granted in day to day living. This paper considers how these themes will impact pyrometallurgical flowsheets using the non-ferrous base metals as an example. It will examine the flowsheet chain to offer views on the boundaries of flowsheet optimization and the application of available tools to meet these future goals and challenges. INTRODUCTION The themes of reducing footprint through lowered CO2, S and other emissions, together with process sustainability (e.g. lowered energy) and links to the circular economy are well known to everyone in the metals industries. Whether it is reducing greenhouse gas emissions or analysing the importance of metals recycling in the circular economy, all these themes carry with them the fundamental premise of any change being considered; how can you best optimize a system to meet your aims? Of course, this depends on the available tools and the approach used for optimisation.

Jan 1, 2019

By K. Scalise, M. Teixeira, K. C. Kocsis, J. Parrish

"This paper aims to introduce and discuss a newly developed algorithm, which can be uploaded on smart watches and other mobile devices to inform and protect underground personnel working in hot and humid environments. Using this algorithm, the metabolic rate (M) of a worker can be determined in “real-time”. In addition, besides warning signs and alarm signals emitted by the smart watch, the algorithm has the ability to determine work-rest time periods based on the worker’s physiological parameters (e.g. age, height, weight, gender) and the climatic parameters (Td, Tw, flow velocity). This paper also investigates whether a re-designed auxiliary ventilation system can provide appropriate work conditions in the production stopes. INTRODUCTION An underground environment with high temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to heat-related illnesses such as heat rash, heat cramps, heat exhaustion, and heat stroke. Heat stroke is a serious illness that carries a high risk of fatality, if the underground workers are not immediately treated and the climatic conditions are not corrected (McPherson, 1993). There are two methods used to control the climatic conditions in underground mines: (1) Using ventilation and cooling systems to reduce the thermal stress on the mine workers, and (2) Reducing the heat transferred to the ventilating air from major sources such as: strata, auto-compression, mining equipment, groundwater, blasting, etc. The heat from strata and auto-compression is transferred to the ventilating air at varying degrees, based on factors such as the virgin rock temperature (VRT), the thermal properties of the surrounding rock formations, and the surface air temperature. However, the use of mining equipment and blasting processes can be managed to reduce their contribution to the mines’ overall heat load. To provide appropriate work conditions, selecting the most suitable cooling method depends on the level of heat to be removed, the location of the problem areas, and economic constraints (Brake & Bates, 2002; McPherson, 1993). Because every mine is unique, it is essential to monitor the climatic conditions to select the most appropriate method of cooling. A majority of the time, simply adjusting or re-designing the auxiliary ventilation system can efficiently remove the heat and dilute the contaminants. This may involve moving the ducting system, changing the size of the duct, changing the size of the auxiliary fan, or switching from forcing to an exhausting fan arrangement. If the required air volumes are higher than the existing primary ventilation system can supply, other measures may need to be taken to increase the airflow delivery. This may include regulating the flow in some areas of the mine to increase airflow to the desired area, adding booster fans, or replacing the primary fans."

Jan 1, 2019

By P. Lin, S. G. She

"In June 1985, Chinese Society for Rock Mechanics and Engineering (CSRME) was established. During the past 30 years, various major achievements are made in the discipline of rock mechanics and rock engineering field, especially in the last ten years. This paper will discuss the main rock engineering progress in association with China National Science and Technology Awards, “973 Program”, and “Tan Tjongkie Lecture”. The current status of rock engineering in China and some hot problems are summarized. Furthermore, some suggestions are given for addressing those problems. INTRODUCTIONThe modern concept of rock mechanics and engineering was initiated and developed after the Second World War. In this regard, the International Society for Rock Mechanics (ISRM) was established in 1962, subsequently further promotes its development. In June 1985, the Chinese Society for Rock Mechanics and Engineering was established. Various chief scientists, including professors Tan Tjangkie, Pan Jiazheng, Sun Jun, Wang Sijing, Qian Qihu, have made their huge efforts to the development of Rock Mechanics and Engineering in terms of the large-scale rock engineering projects in China.The achievements in the last 30 years significantly promote the development of China in different fields, such as energy, transportation, national defense and other national economy and major infrastructure facilities (Wang et al. 2004; Qian 2010, 2011). In other words, these projects also promoted the science and technology progress in rock mechanics and engineering across the world. Reviewing and analyses of the experiences on those key rock projects are beneficial to its technological development. She and Dong (2013), in view of literature statistical analysis, discussed the status and research progress in rock mechanics field associated with the last 30-year China's developments, including the rock strength and deformation theory, rock fracture and damage mechanics, the constitutive relation of rock dynamics, rock field coupling, rock reinforcement and stability analysis, etc. The challenging issues in rock mechanics were also proposed, which are the main concerns in rock engineering practices, engineering exploration, design, construction and operation."

Jan 1, 2015

By C. Graham

Thin Spray-On Liners (TSLs) have been researched and in development for over two decades and yet their fully functional and widely justifiable application in mining has yet to be achieved. While the explanation for this is partly technical, it is also clear that proving and communicating the operational and economic case for why a mine should change from mesh or shotcrete liners to a TSL is not a trivial matter. Evidence must be presented and communicated effectively, that is both obvious and compelling for a mine operator. The paper describes recent work carried out and directed towards this end, with funding from CAMIRO?s Deep Mining Research Consortium and additional support from 3M Canada and ABB Canada. The essential progress that has been, or is in the process of being made, will be described in providing the necessary proof of acceptable or superior TSL performance in the following areas: polymer formulation, health and safety, geotechnical specification, robotic liner application, business case economics and yielding ground support effectiveness. Future plans are also presented to demonstrate the performance of a new 3M composite TSL/yielding bolt support system in underground trials where the substrate rock is intended to fail through a number of mining-induced mechanisms.

Aug 1, 2013

By T. Patching

"Introduction The occurrence of coal was first reported in the Drumheller area in 1793 but it was not until 1912 that production of coal was recorded. In that year 13,000 tonnes were mined in the Drumheller area. Three years later the Drumheller mines ranked next in the Province to those in the Crowsnest and Lethbridge districts, with an output of 225,000 tonnes. By 1917 production had increased to 600,000 tonnes, moving Drumheller to second place in output in the province, second only to the Crowsnest district. It held this rank until 1960. Production, almost all from underground mining, rose to over a million tonnes a year by 1920 and remained between one and two million tonnes per year until 1954. Competition from newly discovered oil and natural gas, beginning around 1950 caused a steady loss of domestic coal markets, especially from underground mines. By 1960 Drumheller's production had fallen below a half a million tonnes per year and the field ranked third in output in the province, being surpassed by new stripping operations in the Castor field. By 1965 only a couple of producing mines remained in the Drumheller valley, and output was only about a quarter of a million tonnes per year(1). Throughout the life of the field production was seasonal, depending mainly on the domestic heating market. In 1979 the last mine ceased production. For the last several years of its operation it had remained open in the summers to provide tours for visitors(2). The Drumheller mining operations were located along or near the Red Deer River valley which is 300 to 400 feet deep, and extended from a few miles above the city of Drumheller to East Coulee, about 13 miles down the river in a south-easterly direction. Intervening mining communities existed for some years at Wayne and Rosedale. During the peak years of production some 2000 to 2500 miners and their families lived in these communities and the surrounding areas."

Jan 1, 1985

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By Troy Boisjoli, Sean Hillacre, Matt Batty

Discovered in 2014, the Arrow Uranium Deposit has undergone rapid development through successive drilling programs informed by geostatistical drill hole spacing studies. An independent third-party geostatistical drill hole spacing study was completed by Clayton V. Deutsch Consultants Inc. in 2017, evaluating the uncertainty of thickness, grade, density, and areal limit of the Arrow Deposit to determine a drill hole spacing suitable for Indicated Mineral Resources. Indicated spacing was defined to be 24 to 32 metres (“m”) to be within 15% of predicted for a nominal quarterly production volume with a probabilistic tolerance between 75 and 90%. The study not only defined the Indicated Mineral Resource resultant from the 2016 drill program, but also provided drill hole targeting criteria for subsequent drill programs aiming to convert Inferred to Indicated Mineral Resources. A subsequent geostatistical drill hole spacing study on the Arrow Deposit was completed by Clayton V. Deutsch with Resource Modeling Solutions in December 2018 to define Measured Mineral Resource spacing in support of the 2019 drill campaign. The study resulted in a drill hole spacing of 9 to 17 m to be within 15% of predicted for monthly and quarterly production volumes using an accepted industry probabilistic tolerance of 90%.

Jan 1, 2020

By B. Chareyre, H. Pourpak, L. Scholtès, E. Papachristos

"Numerical methods used to study hydraulic fracturing in low permeability rock masses need to take into account the interaction between the progressive failure mechanism of the intact rock matrix and the pre-existing natural fractures. A fully coupled hydro-mechanical 3D discrete elements model dealing with such interaction is presented here. The ultimate objective is to grasp the role of the rock-matrix failure on the propagation of the main fluid driven fracture under different stress fields and pre-existing fracture orientations. The proposed method provides the spatiotemporal distribution of the induced crack events which can be tracked during the simulations, making possible the identification of the local mechanisms leading to macro-failure in the rock matrix or reactivation of the discontinuity planes. Fluid flow inside a fracture, pressurized crack and hydro-fracking experimental tests were simulated as part of the validation process of the model and, are presented in this paper.INTRODUCTIONWith the expansion of shale gas and geothermal reservoirs exploitation, the technique of Hydraulic Fracturing (HF) has been widely used over the past years (McClure, 2012; Britt, 2012). Despite recent advances in micro-seismicity analysis or numerical modeling (Nagel et al., 2013), the way progressive failure of rocks affects the fluid flow depending on the in situ stress conditions or the rock heterogeneities is not fully controlled yet (Zoback, 2010).In this work we focused on setting up a three-dimensional discrete elements model to study fluid driven fractures propagation. The intact rock is modeled by a discrete element method (DEM) able to reproduce fracture initiation and propagation (Scholtès and Donzé, 2013, Garcia et al., 2013). The pre-existing fractures are explicitly modeled and can be individually defined or be part of a discrete fracture network (DFN) (Harthong et al., 2012). Their mechanical response is fully coupled with the fluid within a HM-DEM framework. The fluid flow and it’s interaction with the intact matrix and the pre-existing discontinuities is modeled through a Pore-scale Finite Volume (PFV) scheme specially enhanced for fractured rock modeling (Chareyre et al., 2012, Catalano et al., 2014) ."

Jan 1, 2015

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

"Sedimented hydrothermal precipitates of silica, now fine-grained quartz, are described from a Pb-Zn-bearing vein system. Their discrimination from the wall-accreted fine-grained quartz that is common in the shallow parts of epithermal systems is discussed. Local fine-grained (<0.3 mm) quartz accumulations occur in a suite of veins with otherwise normal drusiform and crustified infills. This sediment may fill the vein above chokes in steep segments (axial plugs), or form continuous layers within the footwall material where the vein is inclined at low to moderate angles. Pads of fine-grained sediment are deposited on the upwards-facing surfaces of wall-rock clasts and of drusiform crystals growing from the vein walls. The asymmetry of these deposits differentiates them from the more common symmetrical, crustified walllining deposits of fine-grained quartz and opaline silica, and requires a gravity-controlled, sedimentary depositional mechanism.Thin section examination shows that much of the fine-grained quartz is present as elongate prisms. The prism habit was present soon after deposition, but it is not possible to identify unequivocally the original sedimented grains. Sedimentation of vein- and wall-rock-derived detritus is also recognized. Deposition of the fine-grained sediment accompanies normal in situ drusiform growth of quartz and other vein minerals. The mammilated and spherulitic textures associated with accretion of amorphous quartz are entirely absent from the Tyndrum veins with sedimented materials. The literature on modern hydrothermal waters and physical chemistry of silica precipitation shows that precipitates of silica suspended in hydrothermal fluids are amorphous and derived from colloidal silica. It is argued that much of the suspended silica was present as quartz at the time of deposition or was converted from amorphous silica almost immediately after deposition.Hydrothermal sediments and their distribution potentially provide information on flow directions and velocity in veins. Plugs of sediment obstruct vertical flow and lead to local flows with large horizontal components. It is shown that sedimentation features occur in other deposits and can involve other minerals. If the features seen here can be scaled up to the size of major veins, they may result in up and downdip variations in mineral assemblages and abundances, which may affect grade."

Jan 1, 2007

By Brad Bjornson, Geoff Stevens, Mike Ashar, Cliff Britch

"LocationThe facilities are located 30 km north of Fort McMurray, Alberta (or 470 km northeast of Edmonton, Alberta).Brief Description of OperationThe operation includes the mining of oil sands, extraction of bitumen from the oil sands, and upgrading of the hydrocarbon fraction prior to shipment via pipelines to refineries.HistorySuncor was initially called Great Canadian Oil Sands. It was started by Sun Oil of Philadelphia. Construction began in 1965, with the first production coming on September 1967.Details of Present Milling Practice (Plant 3)Plant 3 recovers bitumen from the oil sand using the Clark hot water process. The basic steps in the process are conditioning, primary recovery, secondary recovery and tailings oil recovery.Oil Sand Feed SystemThe oil sand feed from the mine is transferred to the feed bin in extraction by two conveyor systems. Oil sand analyzers on each conveyor system measure the amount of bitumen and fines in the ore. Cones at the bottom of the feed bin distribute the oil sand to five process lines. Feed flow from each cone is regulated by an apron feeder which transfers the oil sand to conveyors that discharge into the conditioning drums. Weightometers on each of these five conveyors measure the rate at which the oil sand is delivered into the drums. The oil sand feed rate to each drum can be adjusted by varying the speed of the apron feeders."

Jan 1, 2000

By Muhammad Zaka Emad

ABSTRACT: Sublevel stoping mining methods with delayed backfill employs cemented rockfill (CRF) as a backfill material. It is used in underground mines to achieve ground control and reduce wall slough. In addition CRF serves to reduce development waste and provides a working surface for mining the upper levels. Efforts to optimize CRF practices have been published. This paper presents a detailed review of CRF practices in open stoping mining systems with reference to case studies. A new methodology is suggested in a simple stepwise approach, which can be adopted for site specific conditions. The need of laboratory testing and quality control program is discussed based on the published literature.

May 1, 2013

By Gabriel Voicu, Marc Bardoux, Ross Stevenson, Nuno Machado, Jean Lafrance

"Abstract - Paleoproterozoic gold is found in two different volcano-sedimentary sequences and intrusive bodies separated by 600 km within the Guiana Shield. The 2148 Ma St-Élie granite intruded volcanic-arc sequences of the Paramaca Group, whereas the 2096 Ma Omai stock penetrated backarc/ island-arc sequences of the Barama-Mazaruni Group. Positive ?Nd values suggest that both suites lack Archean crustal contaminants, which is consistent with an origin in an oceanic arc setting.The St-Élie deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented chiefly by pyrrhotite and pyrite. Biotite, calcite, and chlorite are the main gangue minerals. The alteration haloes at St-Élie feature a strong potassic zone, which is absent at Omai. The ore-controlling structures are ductile and the vein emplacement is related mainly to contemporaneous, high-angle ductile shear zones. The St-Élie deposit formed at temperatures >350°C. The stable isotopes values are compatible with a magmatic or metamorphic source.The Omai deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented mainly by pyrite. Ankerite, scheelite, albite, and chlorite are common gangue minerals. The vein emplacement is syn- to post-deformation and it is related mainly to brittle shear zones with low-angle, stockwork networks and breccia zones. The Omai deposit formed in a temperature range between 250°C and 170°C, much lower than the St-Élie deposit. The stable isotope values are compatible with mixing between deep-seated fluids of metamorphic or magmatic origin with surface- derived fluids.These differences between St-Élie and Omai are interpreted in terms of their depth of formation. Alteration patterns, structural elements, and paragenetic assemblages indicate that the gold at St-Élie was most probably emplaced at a mesozonal depth, whereas the Omai setting yields evidence for epizonal conditions."

Jan 1, 1999