Search Documents

By D J. McDougall

Due to changes in the solid-state conditions of minerals in the rocks surrounding hydrothermal, contact meta-somatic or metamorphosed ore deposits, positive or negative thermoluminescent anomalies may be found in their vicinity. Several types of equipment which can be used for both quantitative and semi-quantitative measurements of the emission are discussed and compared. Methods of selecting, preparing and testing samples to ensure reproducible results are outlined, along with the kind of data which can be obtained from different types of equipment. The normal thermoluminescence of rock-forming min~ erals in the common rock types is noted, and variations in the solid-state conditions in the wall rocks which will cause marked increases or decreases of true thermoluminescence are outlined, as well as the thermolum-nescence-like emissions which are present in the vicinity of ore deposits. Introduction T HERMOLUMINESCENCE occurs when certain crystalline materials are heated to temperatures ranging between 180' and 400°C. The light emission can be ascribed to the release of electrons metastably trapped within the crystal lattice, with peak emissions taking place at temperatures which are more or less specific for a particular set of traps; the area under

Jan 1, 1965

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

By W. G. Jewitt

THE Box mine, situated in Saskatchewan on the north shore of lake Athabasca, is unique in two respects. It is the first and, so far, the only gold mine in Saskatchewan, and it is the only gold mine in Canada to employ a large-scale forced caving system as the main mining method. Discovered in 1934 by Tom Box, an Edmonton prospector, its subsequent history, while breaking no records for speed, has been one of steady and more or less normal development. Camp and plant are situated close to the shore of Beaverlodge bay, sorne 50 miles east of the Saskatchewan-Alberta boundary and 35 miles south of the north boundary of the Province. The railhead at Waterways, Alberta, is about 220 miles to the southwest. Prince Albert lies some 450 miles to the south. The surrounding country presents a rather rugged variation of the usual Precambrian topography, with hills rising five to six hundred feet above lake Athabasca. The numerous lakes and islands, together with the wide expanse of lake Athabasca, compose an attractive scene, at least in the not over-long 'open water' season. The winters are long but not extremely cold, judged by prairie standards. The small lakes break-up around May 20th and the 'freeze-up' stops navigation early in October. Though apparently remote, the Box mine is fortunate in having reason-ably cheap transportation from Edmonton. The 300-mile railway from Edmonton to Waterways is the most expensive section, the rate for 1st class freight being $1.70 per hundred pounds and for 5th class freight $0.77 per hundred. Freight from Waterways to the mine, approximately 140 miles down the Athabasca river and 90 miles along lake Athabasca, is delivered by barges and tugs for 50 cents per hundred pounds. All freight is delivered during the 'open water' shipping season, which lasts from about .Tune 7th to October 7th. In normal years, barges are loaded to 3 to 3 1/2feet draught up to September 1st. After that date, and earlier in dry years, shallow water at Waterways reduces the barge loads. Barges of 100 to 200 tons capacity handle all mining freight, including pieces up to 15 tons in weight, without undue difficulty.

Jan 1, 1940

By R. Carrier

"There has been a continuous evolution with the use of pre-cast concrete elements in the construction of aluminum smelters. In 1990, Phase I of Alouette was built using cast-in-place concrete exclusively. Whereas, other AP 30 technology plants such as Hillside 2 in the mid-1990s used pre-cast concrete beams with cast-in-place floors. Mozal 2, in 2002, used pre-cast concrete beams with pre-cast partial-slab operating floors. Alouette Phase II went further. Not only were the potroom building beams and floors pre-cast, but the entire pot support system, insulating walls and basement jersey walls were pre-cast. Once the techniques for bending and welding the reinforcement bars and the design for attaching electrical insulating plates to the concrete was perfected, the challenge for the project remained only in the logistics of transporting the pieces to site and simple erection. The overall impact on the project was dramatic. Using prefabricated concrete not only allowed advancement of the schedule, but totally eliminated formwork, re-bar installation, and form removal activities along with the handling of all the materials involved with these activities. With the elimination of these labour and material-intensive portions of the job, exposure to work injuries was dramatically reduced. The most prevalent activity for lost time accidents is during the rough work associated with concrete formwork, placing concrete and form removal. Another area where prefabricated elements were successfully used on Alouette Phase II was for the insulating walls enclosing the pot area, known as the ""claustra walls"". Usually these walls are constructed in-situ using mortar and breeze block. Success was also achieved with prefabrication of the perimetric walls that are installed at the lower floor of the potroom. A big advantage of using prefabricated concrete in the electrolysis area is in assuring electrical isolation for the operating floors. Poured concrete requires a meticulous clean-up effort before commissioning to establish the electrically ""floating"" characteristics of the operating floors. Poured concrete results in ""wash"", stray wood,"

Jan 1, 2006

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT?s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By A. van As, J. McGaughey, M. J. Mol, R. Tosen

Geotechnical monitoring is a key element of the successful management of a block cave mine. The interrelationships between production and various monitoring datasets are often not realized due to a lack of data integration and appropriate 3D visualization. Timely delivery of information to ensure best cave management practices is only possible with an integrated cave management system. At Rio Tinto, a state-of-the-art cave management system (CaveCAD) has been designed and developed in cooperation with Mira Geoscience to integrate and analyze vast datasets and report this as instructive information regarding the current \u201cstatus\u201d of the cave.

Jan 1, 2014

By Derek Perkins

"Brenda Mines Ltd. operates an open pit copper and molybdenum mine located in south central British Columbia. The main economic mineralization is chalcopyrite and molybdenite. Pyrite, galena and sphalerite are also present in varying quantities. The mineralization is present in small veins and fractures in a porphyritic quartz diorite host rock.The mill processes approximately 30,000 tonnes of ore daily. The ore is crushed in three stages and then ground in conventional rod mill - ball mill circuits with cyclone classification. The cyclone overflow is fed to the bulk flotation circuit as a pulp with a density of 50% solids. The particle size distribution is approximately 35% plus 65 mesh. Bulk rougher and cleaning flotation produce a concentrate grading approximately 20% copper and 4% molybdenum. This concentrate is fed to the separation circuit, where the copper is depressed with sodium hydrosulphide and the molybdenum is floated. These products are further ground and then upgraded by column flotation. The molybdenum concentrate is pumped to the leach plant to reduce concentration of lead and copper. It is then washed, filtered, dried and packed for shipment to Europe. The copper concentrate is filtered, dried and subsequently shipped to Japan.Prior to November 1977, the mill flotation control was carried out by the assay laboratory using a Philips PW 1540 sequential x-ray spectrograph. The assay set consisted of twelve samples, analysed on a two hourly basis for copper, molybdenum, lead, iron and silica.In order to provide elemental composition information on a much shorter sampling interval and to produce speedier control analysis for automating process control, an Applied Research Laboratories PCXQ on stream analyser was purchased. The installation of this analyser, reduced the turnaround time of the control analyses from (2) hours to (20) minutes. At Brenda, the following assays are used in the mill control strategies."

Jan 1, 1989

By G. M. Ross, J. A. Scott, C. A. Laamanen, H. Shang

"Indirect recovery and use of waste heat contained in smelter off-gas is proposed to expand regions available for year-round, on-site production of micro-algae–sourced biodiesel, a fuel that could be used in underground machinery. A dynamic model of an off-gas heat exchanger describes capture and distribution of heat into open, external, rectangular micro-algae ponds. Smelter off-gas contains sufficient energy to maintain large-scale micro-algae cultivation pond temperatures above 15°C, even with winter ambient temperatures below –15°C. Results highlight opportunities that could lie in tapping these heat resources to produce renewable biofuels on-site and sequester CO2 while leaving the industrial process unaffected.RÉSUMÉ On propose la récupération et l’utilisation indirectes de la chaleur résiduelle contenue dans les dégagements gazeux des fonderies pour développer les régions se prêtant à une production toute l’année durant et sur place de biodiesel à partir de micro-algues, carburant dont on pourrait se servir pour le matériel d’exploitation souterraine. Un modèle dynamique d’échangeur de chaleur contenue dans les dégagements gazeux décrit le captage et la distribution de la chaleur dans des bassins rectangulaires ouverts de micro-algues en extérieur. Les dégagements gazeux des fonderies contiennent suffisamment d’énergie pour maintenir les températures des grands bassins de culture de micro-algues au-delà de 15°C, même avec des températures ambiantes en hiver inférieures à –15°C. Ces résultats soulignent les possibilités que pourrait offrir l’exploitation de ces sources de chaleur pour la production de biocarburants renouvelables sur place et pour la séquestration de CO2 sans que cela n’ait d’incidence sur le procédé industriel.INTRODUCTIONMicro-algae that grow in water can efficiently convertsolar energy and carbon dioxide into biomass. This biomass can be up to 50% oils (lipids), which can be extracted and converted into biodiesel through transesterification (Demirbas, 2008). Compared to terrestrial plants that produce similar oils (e.g., jatropha, soybean, and rapeseed), micro-algae represent an order of magnitude increase in areal productivity, do not require arable land, and can be continuously harvested (Rawat, Ranjith Kumar, Mutanda, & Bux, 2013). The potential advantages through the production of biodiesel from micro-algae also include sequestration of carbon dioxide, reduced reliance on fossil fuels, and the co-production of other value-added bioproducts."

Jan 1, 2017

By P. -A. Bosse, J. Robitaille, P. Blatter

The LaRonde ore is a Cu-Zn-Pb ore with gold (3-4 g/t) and silver (60-100 g/t). The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation. Subsequent to a recent mill expansion, excessive gold was reporting to zinc concentrate with a concurrent decrease in gold to copper concentrate. Owing to the higher return obtained from the metal, the mill endeavors to recover additional gold and silver to the copper concentrate and minimize the placement of precious metals to the zinc concentrate. A gold deportment study showed that the gold occurs mainly as küstelite, with a moderate amount of electrum and a minor amount of native gold. It also showed that various sulfur-based Au-and/or Ag-bearing coatings on liberated küstelite and electrum were the major mineralogical factors that caused gold and silver to report to zinc concentrate. By frequency, such coatings were observed on 70-80% of total liberated gold particles reporting to the zinc concentrate. Based on the gold deportment and the chemistry of the coatings, the collector chemistry was reviewed and a new collector was added into the circuit which resulted in a significant increase in gold and silver recovery to the copper concentrate. The information obtained from the mineralogy confirmed and guided other process optimization. In this paper, the authors will describe the process mineralogy of the LaRonde ores, and in particular, the mineralogical evidence diagnosing the problem. Reference will also be made to the rationale behind how the problem was solved, the results achieved, and future steps in optimization.

Jan 1, 2005

By V. K. Karra

A mathematical model for the performance of a vibrating screen is developed in terms of an oversize partition curve. This is a normalized curve for any assemblage of particles presented for screening when their size is normalized with respect to the 50 per cent passing size (d50 ) under the prevailing screening conditions. Based on the throughfall aperture (hT) of the wire mesh on the deck, the effects of oversize (% >hT), half-size under (% <0.5 hT), deck location and feed rate were evaluated using the existing screen sizing information. All these variables and also the near-mesh (1.25 hTx 0.75 hT) content (%) of the feed affect the d50. Performance data from different decks of a double-deck screen with various feed rates, size distributions and screen apertures were used to evaluate the near-mesh factor. Effects of wet screening and material bulk density are also incorporated in the model. This generalized model is useful for the simulation of a multiple-deck screen. It furnishes the sieve analysis information of all the deck output streams and therefore has a potential use in the over-all circuit evaluation when used in conjunction with relevant crushing and grinding performance models. An example illustrating the prediction capabilities of the model is given.

Jan 1, 1979

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By J. Mrozowski, R. Kurowski, A. Chmielarz, Z. Szolomicki

PbSO4 is a commonly encountered component of the materials used in lead recycling (e.g. battery paste) and in by-products of metallurgical processes (e.g. residues from zinc hydrometallurgy, dust from copper smelting). Smelting of battery paste results in SO2 emission and in generation of significant amounts of hazardous ‘white slag’. Those adverse phenomena can be eliminated by removal of sulphur from the paste. Lead-bearing by-product materials are of polymetallic character with usually low Pb content, which makes lead recovery technologically difficult and uneconomic. However it can be successfully achieved by extraction of lead sulphate from solid phase with triethylenetetramine (TETA) water solutions. That compound has capability for selective solvation of a whole lead sulphate molecule. Virtually pure lead carbonate can be precipitated by means of saturation of lead-loaded aqueous TETA solution with carbon dioxide, and complete regeneration of the extractant is achieved by fixing of sulphate ion into gypsum through operation of calcium hydroxide suspension. The paper presents results of the lab and pilot scale studies into process of battery paste desulphurisation and recovery of lead from the residue of zinc calcine leaching.

Jan 1, 2014

By Robert Yobou, Jacques Naho, Benjamin A. Allou, Jacques Carignan, Huan-Zhang Lu, Jayanta Guha, Koffi Pothin

"Résumé - Les seules productions de columbo-tantalite en Côte d&apos;Ivoire sont effectuées dans les éluvions, colluvions et alluvions d&apos;Issia, au Centre-Ouest de la Côte d&apos;Ivoire. Même si un lien direct avec les roches granitiques est suspecté, aucune attention particulière n&apos;a été accordée à l&apos;étude de la minéralisation primaire en relation avec l&apos;évolution de ces granites et des pegmatites associées. Ces granites, qui sont en intrusion dans les roches sédimentaires du Protérozoïque inférieur, comprennent: le granite orienté à deux micas (type Lobo), le granite orienté à muscovite dominante (type Bitapia) et le granite porphyroïde non orienté à muscovite dominante (type Issia). Les résultats de cette étude indiquent que les pegmatites à Nb-Ta-Be-Li sont liées au granite de type Issia. Les observations de terrain et les analyses sur roche totale montrent que: (1) les trois principaux granites de la région sont de type-S et peralumineux dans leur composition, (2) ils ont été formés pendant la période tardi- à post-Éburnéenne, (3) le granite de type Issia fut le dernier à se former.Les pegmatites liées au granite de type Issia ont été classées en quatre types : A- pegmatites stériles; B- pegmatites à Be; C- pegmatites zonées à Nb-Ta-Be; et D- pegmatites zonées à Be-Nb-Ta-Li. Les pegmatites zonées comprennent les zones suivantes: I- zone à aplite; II- zone graphique; III- zone à albite, microcline, béryl et columbo-tantalite; IV- zone à microcline massive; V- zone à quartztourmaline. Ces pegmatites présentent une zone d&apos;altération métasomatique externe.La minéralisation de Ta, Nb, et Be est liée à la zone III des pegmatites de types C et D, la minéralisation de Li est associée aux greisens qui peuvent être observés n&apos;importe où dans les pegmatites de type D. Les données de terrain et de laboratoire indiquent que le granite de type Issia est la roche parentale des pegmatites à éléments rares de la région. Les pegmatites minéralisées sont distribuées seulement autour du granite de type Issia et les patrons des terres rares des granites et ceux des pegmatites à éléments rares sont très similaires. Les analyses de la composition totale montrent un lien génétique entre le granite de type Issia et les pegmatites à éléments rares. Il est suggéré que les pegmatites ont été formées durant le transport et la cristallisation fractionnée du magma. Les éléments rares sont restés dans le liquide résiduel jusqu&apos;à ce que les conditions favorables à leur précipitation soient atteintes.L&apos;établissement de ce lien génétique ouvre des voies pour des nouvelles stratégies d&apos;exploration."

Jan 1, 2005

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By Y. N. Zhang

Friction Stir Welding (F SW) is a novel "green" manufacturing technique due to its energy efficiency and environmental friendliness. This solid-state joining process involves a rotating tool consisting of a shoulder and/or a probe. The shoulder applies a downward pressure to the work-piece surface, constrains the plasticized material around the probe, generates heat through the friction and causes plastic deformation in a relatively thin layer under the bottom surface of the shoulder. The rotating probe mainly drags along, plasticizes, and mixes the adjacent material in the stir zone, creating a joint without fusion. Friction Stir Processing (FSP), a variant of FSW, has been developed to manufacture composites, locally eliminate casting defects, refine microstructure and/or improve the associated mechanical and physical properties including strength, ductility, fatigue, creep, formability and corrosion resistance. However, major challenges such as tool design and wear currently limit the use of F SW/P for manufacturing applications, particularly for high melting temperature or high strength alloys. In this review, the FSW/P tools are briefly summarized in terms of the tool types, shapes, dimensions, materials and wear behaviors.

Jan 1, 2011

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By D. V. Dorling, J. T. Bowker, J. A. Gianetto

Over the last few years, interest in the development and construction of large diameter, high pressure pipelines from the Mackenzie Delta in northern Canada and Alaska&apos;s North Slope has steadily increased as a result of the projected decline in recoverable natural gas from existing reserves in western Canada. The success of such enormous pipeline projects, which will require utilization of a strain-based design approach, is largely based on successful application of high strength line pipe steels, such as X80 and X100. To fully realize the economic benefits of high strength steels, welding processes and procedures must be developed to ensure that the requirements for high strength and good low temperature toughness are confidently obtainable in field girth welds used in the construction of such pipelines. This study aims to provide a better understanding of the factors that control weld metal strength and toughness for a series of mechanized X100 girth welds produced using a range of narrow-gap gas-metal arc welding procedures. The attainment of high yield strength (> 810 MPa) is considered to be an important target to ensure overmatching strength relative to the longitudinal property distribution of X100 line pipe steel. Some factors that have been considered in this evaluation include influences of gas-metal arc welding process variants (single and multi-wire) and changes in welding procedure specifications, including joint preparation. Key components of this work relate to the reliable measurement of weld metal strength variation through-thickness and as a function of position around the circumference of a given girth weld.

Jan 1, 2005