Search Documents

By J. H. Sokolowski, R. I. MacKay

The level of Si and Cu in the 3xx series of alloys affects the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase. The volume fraction of these phases in turn affects the feeding conditions during solidification and ultimately the Area Fraction Porosity and Mean Pore Diameter measured in the as-cast structure. This work sets out to establish the relationship between the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase and the resulting porosity that forms on the Monotonic and High Cycle Fatigue properties. The alloys in question are the Al-9%Si-l %Cu and a Al-7%Si-4%Cu alloys which were cast into V8 performance engine block castings and then heat treated to achieve desired mechanical properties. The engine block castings provided the mechanical and metallographic test samples analyzed for this work.

Jan 1, 2006

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By G. Deschenes

"This literature survey discusses the recovery of gold from thiourea solutions. An overview of techniques used and general comments on the basic cyanidation methods are presented. The chemistry and mechanisms of cementation, activated carbon, resins, electrowinning, solvent extraction and pressure reduction are examined. Conclusions and recommendations give orientation for future research and development activities in this field.RésuméCette revue littéraire traite de la récupération de I ‘or des solutions de thiourée. Elle fait un survol de I ‘ensemble des techniques utilisées tout en introduisant des commentaires généraux sur la méthode classique qu'est la cyanuration. La cémentation, Ie charbon active, les résines, l'électroextraction, I ‘extraction par solvant et la réduction sous pression sont les méthodes analysées tout en considérant leur caractère chimique respectif ainsi que les mécanismes qui y sont rattaches. Des conclusions sont tirées et différentes recommandations sont suggérées pour orienter la recherche dans ce domaine."

Jan 1, 1986

By Angus D. Campbell

Introduction In the Twentieth Annual Report of the Mcintyre Porcupine Mines, Limited, for the year ending March 31st, 1932, the General Manager, Mr. R. J. Ennis, said: "During the period under review, the plans outlined in last year's report have been completed, and all operations have been centralized in the new plant adjacent to No. 11 shaft. The new mill went into operation on May 27th and attained its rated capacity of 2,000 tons per day on November 15th. The new shops, warehouse, change-house, and general offices were occupied on December 1st, consummating the change from the old to the new plant ... "Silicosis is now definitely recognized as an industrial disease, and progresses rapidly when associated with tuberculosis. In an effort to combat its prevalence and progress, the new change-house was designed to build up the men's resistance to this and other forms of disease. It provides for a complete change from underground to street clothing, with a shower bath and solarium treatment in the interval. 'Unfortunately, in almost every goldmine, a very small percentage of the work-men are not adverse to taking some of the high-grade ore for their own purpose. This, in turn, tends to cast suspicion upon the honourable as well as the dishonorable employees. The new change-house routine discourages this practice and eliminates unjust suspicion, to the satisfaction of all concerned with the Company's operations".

Jan 1, 1933

By W. H. Gross

To pollute means to make impure or unclean. We tend to forget that man defecates, urinates, sweats, expectorates and exhales and in himself is a beastly little pollutor-but then so is Mother Nature! The object of this paper is to try to put what man and nature do into perspective. The facts indicate that although man may sweat a little, Ms. Nature is by for the greatest pollutor of all.

Jan 1, 1979

?Four-wheel, skid-steer, rover developed for CSA ?U-chassis for payload accommodation ?Passive geometric suspension ?Max speed 13km/hr ?Remote workstation ?275kg payload capacity ?On-board processor, IMU, motor encoders ?5.2kW-h battery capacity

May 1, 2013

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By Zhiqiang Wang

This paper mainly focuses on the method of ?three-zone? definition (a caving zone, a fissure zone and a curve subsidence zone) for full height cutting in a thick seam. Based on criteria of a caving zone and a water conducting zone, as well as existing research achievements, it is believed that there exists great error for calculation of height of the ?three-zone? area using cutting height and the coefficient of bulk increase. Dynamic factors should be considered, so, based on the theory of key rock strata and combining this with several other factors, such as mining area, this paper presents a new method to determine the overburden ?three-zone? definition. The results are as follows: (1) geometric models of a working face and key stratum are established through the rock displacement angle, with consideration of the influence of mining on the key stratum (the range of key stratum influenced by mining is enlarged as the mining area increases); (2) because there is always a cavity below the key stratum of the thick coal seam with full seam cutting, and the key stratum gradually fracture with face advancing, based on the geometric dimension of strata, the maximum fracturing interval expression has been presented, including the working face advancing range. This can theoretically lead to the location of the key stratum influenced by mining, and its stability before mining, helps to confirm which zone the key stratum and following-up strata belong to, using the criteria of sliding instability or deformation instability; (3) the new method of ?three-zone? definition which is based on the theory of key rock strata is first proposed for full height cutting in thick seam. Finally, combined with practical engineering, and comparing with field data, it is believed that the proposed method is more objective than existing methods.

Aug 1, 2013

By P. G. Smith, A. Axiuk

The objective of this paper is to present, from a practical perspective, a review of the most relevant maintenance procedures that are accepted or prescribed to be the most effective in optimising service life potential and to ensure continued safe use of steel wire ropes for shaft mining applications. The paper will address the most common operational issues encountered in the care and operation of shaft ropes for both conventional drum hoists and multi-rope friction winders. For each distinct maintenance procedure presented, a limited amount of theory is discussed to identify the underlying mechanisms at play that must be addressed and to emphasize the logical basis for the recommended course of action. It is recognised that each installation is unique and that the recommended maintenance procedures may not always be practical or cost effective from an operations standpoint under select circumstances, however the intent remains to promote industry best practices for the knowledge and benefit of the mine hoisting community, from experienced maintenance personnel to new entrants to the industry alike.

Jan 1, 2023

By L. Long

Stirred milling of nickel laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on siliceous goethitic (SG), goethitic (G), and saprolitic (SAP) nickel laterite samples (- 2000 ?m particle size) to evaluate the effect of stirrer speed, solid content, water salinity and grinding time. A fine mineral product (-38 µm) was used to evaluate the effect of selective grinding and Ni upgrade. The optimum grinding time for the highest Ni upgrade was 0.25 min, 0.1 min and 0.1 min for the SG, G, and SAP nickel laterite, respectively. A new feed (38-2000 µm) for each nickel laterite sample was prepared for batch grinding tests under the optimum grinding conditions. Upon grinding the 38-2000 µm feed, the - 38 µm product confirmed the effect of selective grinding and nickel upgrade. Size classification followed by stirred milling is a suggested process for Ni upgrade. The best Ni upgrade result was achieved on the SG nickel laterite among the three samples. The Ni grade increased from 0.85% to 1.37%, with 27.8% Ni recovery. Bottle roll leach tests showed that for SG and SAP samples selective grinding had no dramatic effect on Ni extraction due to the slow leach rate of hard mineral particles. Stirred milling of G sample increased the surface area of goethite, resulting in higher Ni extraction. Gravity concentration through a Knelson Concentrator was not effective in the further treatment of the stirred milling products either due to the poor operating conditions or due to the mineralogy characteristics of the feed samples. The energy requirement in the stirred milling was investigated. The first pass of the signature plots study is critical for the purpose of selective grinding, because the best result on selective grinding is achieved in the early stage of the grinding process.

Aug 1, 2013

By A. Brian Hawkins

"When pyrite oxidizes in dark grey/black, calcareous, mudrocks or in argillaceous limestones, ferrous sulfate is formed and sulfuric acid is released. The sulfuric acid combines with the calcite present in the rock and calcium sulfate (gypsum) develops. When this occurs on the outer edges of aggregate particles, the gypsum forms in the matrix hence there may be little expansion of the general material. However, when the chemical reactions occur within the rock fragments, particularly on microscopic, clayrich, laminae, the developing crystals exert a significant pressure on the host material. If the rock is medium strong to strong, the force of crystallization splits the rock along the weaker planes, facilitating the ingress of the oxidizing agents and the continuation of the chemical reactions. In addition to causing dilation/heave, some of the engineering properties of the material are changed, including the strength, Los Angeles value, water absorption etc. As a consequence material, which at the time of quarrying would be acceptable for use beneath floors or hardstandings, would no longer be considered suitable.INTRODUCTIONMudrocks accreting in aerobic environments are frequently disturbed by organisms and as a consequence there is often little sign of bedding. In contrast, sediments which have formed in anoxic environments commonly have distinct bedding planes which, because of the grain size of the accreting material, are often smooth and planar. These rocks are frequently referred to as shales, which O’Brien and Slatt (1990) define as “characterised by a finely laminated structure, which imparts a fissility approximately parallel to the bedding.” This should not be confused with rhythmic bedding where the variation in grain size results in lithological laminations or colour changes.Early geologists, in the stratigraphic naming of rocks, often used the term shale for material which is now more likely to be described as mudstone or mudrock (Hawkins and Pinches, 1992). In many contexts, the width of the bedding is an important factor, not only in determining the rock name but also in indicating the potential engineering characteristics. Until recently a shale was considered to have bedding separations of less than 20mm, i.e. the bedding was described as laminated. However, in an engineering context, EN 14689: 2003, Annex A, defines shale by specifying a bedding thickness of < 6mm; such a material would be described as thinly laminated in BS 5930:1999. Ideally the term shale should be abandoned and be replaced by fissile mudstone or fissile mudrock."

Jan 1, 2015

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

By J. Seo

We propose a dynamic biomechanical simulation method that uses motion capture to evaluate the risk of Work-related Musculoskeletal Disorders (WMSDs). Statistics show that WMSDs accounted for 33% of all non-fatal occupational injuries and illness in construction in 2009, and were a leading cause of temporary and permanent disability. Present methods rely largely on self-reports from workers, observational techniques, and direct measurements of motion and muscle activity to assess awkward postures, physical loads, repetitiveness, and the duration of exposure. While these methods have helped to prevent WMSDs in construction work, they may not be suitable for estimating the internal tissue loads associated with WMSDs. We propose a dynamic biomechanical simulation method to estimate internal forces and moments at each body joint of construction workers with motion capture data. Particularly, we explore the biomechanical loads by simulating active 3D musculoskeletal models based on measured postures and movements. To demonstrate the feasibility of this approach, we studied a ladder climbing task using a portable ladder under controlled laboratory conditions. Postures and motions were determined with a commercial motion capture system (e.g., VICON). The results were analyzed to investigate the feasibility of identifying risk factors based on biomechanical simulation. The results show that the proposed approach allows us to determine the biomechanical basis for WMSDs, and to identify postures and movements associated with excessive physical demands on each body joint. When combined with marker-less motion capture which is our ongoing work, the proposed approach has the potential to assess an individual?s motions and to provide personalized feedback for the purpose of reducing biomechanical loads and WMSD risk in real workplaces.

Aug 1, 2013

By D. Furrer, M. Dallaire

The arrival of Image analysis in the last 20 years has changed the world of quantitative metallography. Many standard measurement techniques which were previously manual can now be done with fully automated systems. This reduces subjectivity and operator fatigue and therefore enhances the quality of the statistical results. In many laboratories, Titanium Alloy microstructures continue to be evaluated by traditional methods, where quality of results is subject to operator fatigue and level of experience. Advances in Camera technology have tremendously improved image acquisition. One can often see clearly at 500x what can not be observed at 1000x, allowing for a larger area to be analyzed, without the inconveniences associated with very high magnification objectives. Powerful and versatile Image analysis software combined with a high precision motorized stage gives access to a multitude of applications, which were extremely challenging or impossible until now. Image Analysis tools such as Multilayer Grab, which reconstructs an uneven image into one plane of focus (ex. Observation at high magnification of texture resulting from etching) and Mosaic which builds an image from a number of fields of view (ex. Reconstruction of very large grains at low magnifications) expand even further the power and flexibility of IA systems. This presentation will describe how automated methods are applied to the point count method and grain size measurement. We will show how cameras and software work together to permit quantitative measurements of primary alpha and prior beta microstructures, as well as lamellar alpha plate thickness in titanium alloys.Automated and semi automated quantitative measurements of various Titanium microstrures have been assessed, using the Clemex Vision PE. Examples of the methods and steps used are presented.

Jan 1, 2006

By Z. Jun, L. Kerning

Jinlong copper smelter and refinery, originally designed for 100,000tpa primary copper and started up in 1997, has been expanding its capacity on the basis of operational optimization and by modifying its facilities. Currently it is producing 210,000tpa primary copper, and the new phase of expansion project with a target capacity of 350,000tpa primary copper is ongoing. This paper reviews problems and improvements made with operation and equipment in the past years. Recent plant operation is briefly described. The expansion projects completed are summarized and the ongoing expansion project is present.

Jan 1, 2007

By B. Tonn, F. Kröger

"The continued development in engine technology is leading to an augmentation in power density which steadily elevates the requirements for thermally and thermo-mechanically highly loaded components such as cylinder heads and pistons. Due to these high performance requirements conventionally applied Al-Si alloys have reached their application limits, since their mechanical properties deteriorate quickly under the influence of heat. Improved applicability is given by Al-Cu-based casting alloys which have a superior high-temperature strength than Al-Si alloys. Since Al-Cu alloys exhibit insufficient casting characteristics, especially regarding hot tearing susceptibility and increased tendency for porosity, it is currently not possible to cast geometrically complex components in robust permanent mold casting processes. The further development of Al-Cu alloys is aimed at finding an optimum between improved castability while high-temperature strength and thermal conductivity are not deteriorated. It is known that a high amount of eutectic reduces the hot tearing susceptibility of an alloy, but it reduces thermal conductivity at the same time. In this paper it will be presented how the conflicting objectives – improved high-temperature strength, good thermal conductivity and reduced hot tearing susceptibility – can be brought together to develop an optimized Al-Cu alloy for application in permanent mold casting.INTRODUCTION At the beginning of the 21st century car, engine blocks were primarily made of gray cast iron (GJL). Less than half a decade later, the choice of material had shifted towards lightweight materials. Ever since, the car engine manufacturing is dominated by aluminum-based alloys. The weight of car engine blocks could thus be reduced by around 50% due to the lower specific weight of aluminum alloys compared to gray cast iron. Furthermore, the high thermal conductivity of aluminum alloys allowed a reduction of complex cooling channel systems and thereby promoted the advancement of this material group. The further development in engine technology leads to an augmentation in power density which elevates the requirements for thermally and thermo-mechanically highly loaded components. For example, in diesel-powered car engines the upper required limits can reach an ignition pressure as high as 230 bar and gas temperatures of up to 1000°C. Thereby, thermal loads can cause high alternating thermal stresses (Grzincic, 2003) which can effectively be reduced by providing high thermal conductivity."

Jan 1, 2017

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By Martin Landwehr

"Dust samplers are based on different principles. The konimeter is based on the number of particles counted; mining applications are based on routine sampling; and the photometrical evaluation of samples is used after the pre-separation of particles above 5 micron by the mining konimeter. In special cases, the Draeger sampler is used for quantitative analysis. General trends are toward larger samples, concentration on a weight basis, fractionation into size groups by different techniques and an analysis of composition. Standards or TLVs already exist in all industries. Surface industries base their criteria on concentrations and quartz contents in particles below 5 micron. The mining industry uses the tyndalloscope routinely to determine concentrations; concurrent] y, the rock content, as deter-mined by ashing samples, is obtained by konimeter.Threshold limits are related to the rock content in respirable fractions and tyndallometrically determined concentrations. The TL Vs are based empirically on Landwehr's ""dust values,"" as agreed upon with the Mines Inspectorates. Recently, and in accurate sampling, dust samplers have been used that count the dust in two fractions -above and below 5 microns. Mineral composition is determined either for all minerais or just for quartz. In assessing the dust hazard by Landwehr's ""dust values,"" all minerais are taken into consideration; in coal dust sampling, however, only the quartz content is taken into account. Efforts are now being made to co-ordinate the different assessment methods, arriving at uniform MAC values in agreement with those of other countries."

Jan 1, 1969