Search Documents

By S. Spigarelli

The creep response of the AE44 magnesium alloy was studied by means of constant load creep tests carried out at 125 and 150°C, obtaining that at the latter temperature the minimum creep rate observed under an applied stress of 100 MPa was two orders of magnitude lower in the investigated alloy than in AM50. The minimum creep rate dependence on applied stress was described by a conventional power-law, e = Aon , where A was a temperature dependent parameter and n was the stress exponent, resulting in a n value close to 30, i.e. by far larger than those observed in commercial alloys with similar Al content. This large difference in creep response was attributed to the precipitation of rare earths (RE) intermetallic phases distributed in the grain boundary zone in form of an almost continuous network of dispersoids that were observed by means of scanning electron microscopy.

Jan 1, 2006

By Mei-Yan Yang, Qiu-Ying Wang, Ltd. Yunnan Yuntong Zinc Co., Guo-Mu Chen, Meng-Yang Huang, Peng Zeng, Guo-Feng Li

"Historically, alot of jarosite was found in the leaching residue when leaching indium from secondary zinc oxide materials. The reasons for the formation of indium bearing jarosite were theoretically analyzed. The influence of controlling the acidity and the addition of reagents on the indium leaching yield during secondary zinc oxide processing was investigated. In order to increase the leaching yield of indium, a measure of controlling the creation and destruction of jarosite was proposed. The production data shows that the leaching yield of indium was increased from 60 to 96%, and the content of indium in leaching residue simultaneously decreased from 900g/t to 100–200g/t when implementing such controlling measures.INTRODUCTIONIndium does not occur as independent minerals in the earth’s crust and is mainly associated with complex sulphide minerals. Specifically some sphalerites can contain as much as 900g/t of indium. Most indium is recovered from by-products of copper, lead or zinc metallurgy. Therefore, the research on the recovery of by-products in non-ferrous metallurgy is important(Sinclair et al, 2006). The main technologies used for this objective in China include: •,pre-neutralization-reduction-precipitation indium process(Yu et al, 2008), •,countercurrent oxidizing acid leaching process and sulphation roasting-water leaching process(Cao, 2005), •,oxygen pressure acid leaching of zinc concentrate-P204 extraction process(Yang et al, 2006), •,doubleacid leaching-solvent extraction process on lead dross from a reverbatory furnace flue dust(Liu, 2003),•,an acid leaching-solvent extraction process on smelting ash(Zhouet al, 2005). Although high pressure and extreme conditions can be used to improve extraction from high iron bearing indium residues(autoclave processing), mild extraction with lower cost and lower environmental impact are preferred.This paper describes both how the indium extraction using mild conditions in a secondary zinc circuit was quite low and, how through XRD and chemical analysis jarosite formation was found as the main cause. The paper then proceeds to discuss a method for improving the leaching yield and the application of this method in industrial practice."

Jan 1, 2016

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By T. Grammatikopoulos, K. Gibbs, H. De Souza, C. Gunning

The mineralogy of any ore body is a key factor in defining ore zones and predicting minerals/metals behaviour during processing. The determination of forms of gold, defined as the different chemical states in which gold is encountered in ore deposits, is critical. The most commonly known form is that of gold minerals and alloys, while other forms of gold have been collectively described in the literature as submicroscopic gold (i.e., less than 1 µm in diameter). Gold mining operations generally deal with very low-grade ores, in the order of a few g/t, in which gold displays complex mineralogy. These difficulties complicate the mineralogical studies and pose challenges for processing and recovering the gold. A comprehensive understanding of the chemical forms of gold is necessary to define gold mineralization and optimize gold metallurgy. SGS Canada Inc. has been using QEMSCANTM and a Tescan automated SEM that are automated mineralogical techniques that provide vast amounts of data for microscopic Au. The data in conjunction with other physical and chemical methods provide a comprehensive delineation of the ore composition and behaviour.

Jan 1, 2011

By Xiu-Xiang Tao

This study investigated bio-liquefaction of lignite and its model compounds of thymol, bezioc acid and quinoline by a fungus, Hypocrea lixii AH. It analyzed, during bio-liquefaction, enzyme activity of oxidase, LiP, Lac, MnP and polyphenol oxidase, and degradation products by UV-Vis, FTIR, 13C NMR and GC-MS. The results showed that the bio-liquefaction percentage (by mass) of lignite was up to 44.86 %. The bio-liquefaction products of lignite were mainly aniline, amide, ether, carboxylic acid ketone and ester. The aromatic ring number was 1-3 with an aromatic carbon ratio of 0.328, which indicated rings opening, bonds breaking and oxidation reaction. By considering with the enzyme activity analysis results, it showed that LiP and Lac catalyzed reactions to open aromatic cycles and to break bonds; esterase to break ester bond; and peroxidase in oxidation reaction.

Aug 1, 2013

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

By K. Trapani

"The study undertaken aims to investigate an ice stope heating and cooling system for its potential to be implemented in sub-arctic mines, as a low carbon alternative to conventional natural gas and refrigeration chiller systems. Its performance was simulated for a years’ worth of data, taking into consideration hourly temperature data. Results showed that to supply the required heating and cooling loads, the ice stope system had to supplement its heating with natural heating. The techno-economic performance of this system was compared to that of a conventional heating and cooling system in a mine, with the ice stope thermal storage system hawing the lowest annuitized cost and significantly lower carbon emissions.INTRODUCTIONConventional heating and cooling, in a mine is implemented using natural gas heaters and chiller refrigeration systems respectively. This results in a significant portion of energy consumption in underground mines attributable to ventilation (De Souza, 2015), including the conditioning of the air to ensure that temperatures do not exceed work comfort standards (ACGIH, 2011). Especially at depth where heat could become a significant issue. An ice stope thermal storage, using ice as the storage medium is being proposed as an alternative to provide the heating and cooling—with the ice creation resulting in heating and the ice melting providing the cooling required. A techno-economic investigation of the two systems is undertaken to identify the capital and operating costs for the two systems, and to assess the ice stope’s potential to be considered a low cost and carbon solution for heating and cooling of mines in sub-arctic climates.NATURAL STORAGE SYSTEM – CONCEPT DEVELOPMENTThe concept for the natural storage system is developed from the ice stope at Frood-Stobie Mine, ON, Canada (Stachulak, 1991). The ice stope was developed for mine air heating, with the heating occurring by spraying warm return service water onto the cold intake air—resulting in the air temperature increasing and ice being created in the stope. In summer this ice was melted by passing warm air on top of it, resulting in slight cooling of the air but no significant temperature difference which could allow effective cooling. A schematic of the Frood-Stobie Mine ice stope is provided in Figure 1."

Jan 1, 2019

By Robert D. McKellar, Luke Frawley, Richard Okrasa

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By Courtney E. Cleveland

THE gold deposits of the Pioneer and Bralorne mines, in the Bridge River district of British Columbia, are closely associated with a long, narrow intrusive body of extremely variable composition, outcropping on the northeast side of Cadwallader creek and lying almost entirely within the property boundaries of the two companies. Other masses of the same type of intrusive rock are found in the district, more or less along the line of the main axis of the Pioneer-Bralorne in trusive, and have associated with them variable amounts of gold-quartz mineralization (Figure 1). The ore deposits of the district have been the subject of investigation by officers of the Geological Survey of Canada at various times during the past 25 years, and articles on the geology and mines of the district have been published by various individuals in technical journals. A list of the more important re-ports follows: SELECTED BIBLIOGRAPHY

Jan 1, 1938

By Constantin D. Pitis

?Demand-side measure" means a rate, measure, action or program undertaken to conserve energy or promote energy efficiency?? (BCUC, 1996) In actual economical environment, business sustainability requires high-efficiency technological processes. That is why the efficiency concept has to be present at all levels of industrial activities. Nowadays, some purchasing decisions are still driven predominately by the purchase price, in spite of the evidence that such price represents up to 5 % to 7 % of the total costs of ownership with full consequences of energy efficiency and the impact on total ownership costs. The paper presents essentials of converter types and basics of the Global Efficiency (GEff) Concept that has been promoted over the last few years in South African industries (Pitis et al., 2006/7). GEff concept is proven as a useful tool used on price-efficiency decisions. Theoretical and technical aspects of this concept were substantiated with case studies. First part presented in this paper will describe how GEff concept was used on price ? efficiency decisions when single input or direct converters and systems (considered as low value equipments) have been replaced. Besides the impact of energy savings and new innovative developments, the paper suggests general other benefits of: ? Technical and economical performance improvements and competitiveness of mining corporations to international standards; ? Defusing incipient energy crisis in the sector; ? Improving environmental conditions; ? Creating new job opportunities in mining sector. Proposed concept in this paper could be further developed as models of improving companies? corporate energy policies.

May 1, 2010

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013

By N. M. Stubina, P. J. Lind

Barrick Gold is in the process of building several new mines and implementing new processes at existing mines for which metallurgical technology is of key importance. The roles of the company's Strategic Technology Solutions team and the Barrick Technology Centre are discussed within the context of their responsibilities within Barrick's Operations Support group. The paper will present an overview of the development of the technology centre from the former Placer Dome Research Centre to its current form supporting strategic technology, capital projects, and operating sites. Novel approaches to research and development will be presented as well as an overview of some of the technologies developed from bench-scale to pilot-scale, and beyond.

Jan 1, 2011

By The Mine Staff

THE PROPERTY of the Lamaque Mining Company, Limited, ?is located in the Town of Bourlamaque, seventy miles east of Noranda, in Bourlamaque township, Abitrbi county, north western Quebec. Gold production commenced at Lamaque in April, 1935, with an initial mill capacity of 250 tons per day. The capacity was doubled in November of the same year, and in December, 1937, it further increased to 1,200 tons per day. During the war years the mill operated at a reduced tonnage, but in 1951 milling units were added along with complementary crushing and shop facilities to bring the capacity to 1,500 tons per day. Finally, in 1953, the capacity was raised to 2,000 tons per day, which rate is being maintained at the present time. The total production at Lamaque from April 2nd, 1935, to December 31st, 1956, has been 9,168,901 tons of ore from which 2,208,168 ounces of gold was recovered. The total value of this production , excluding E.G. M.À.*, was $77,869,653.

Jan 1, 1957

By A. W. F. Smith, P. B. Prangnell, D. N. Crowther, P. J. Apps

It is well known that the refinement of grain size in metals leads to a significant improvement in important mechanical properties. As part of a European collaborative project, processing schedules have been investigated aimed at producing a homogeneous ultra-fine ferrite and spheroidised carbide aggregate microstructure structure in high carbon (CMn) steels (0.6-1.2wt%C), via conventional 'warm' rolling and innovative Equal Channel Angular Extrusion (ECAE). Suitable deformation schedules were determined from dilatometry and thermo-mechanical Gleeble simulations. Evidence of an ultra-fine ferrite and carbide aggregate microstructure following 'warm' rolling is given. A significant improvement in tensile strength, particularly proof stress (0.2%) was also noted in comparison to material deformed at higher temperatures. Concurrent Equal Channel Angular Extrusion (ECAE) experiments investigated microstructural evolution with incremental strain. Extensive analysis was carried out using various techniques, including high resolution Electron Back Scattered Diffraction (EBSD). Evidence of ferrite grain refinement was noted in a eutectoid composition steel. A sub-micron ferrite structure was observed following high strains (E-3.33) and the mechanical properties exhibit a marked increase in tensile strength.

Jan 1, 2004

By L. Chunpongtong

One of the challenges of mine planning is to determine the most cost-effective replacement time for aging equipment. The lifespan of equipment, such as haul trucks and shovels, deployed in mining operations varies due to the nature of the material and ground conditions in which it operates. For engineering economists dealing with aging equipment, the options become an economic trade-off between higher maintenance cost versus the cost of new equipment. The discount rate plays a significant role in this decision; the higher the rate, the longer the economically optimal lifespan. Therefore, the ultimate question is: ?How can the relationship between the discount rate and the economically optimal lifespan be expressed mathematically??

Aug 1, 2013

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By X. Gu

Mining operations, especially surface coal mines, have great impacts on the local ecosystem and the environment. However, it has been a common practice in mine design that the economic evaluation considers only the operating and capital costs, while the costs incurred due to ecological damage are left out. Such practice underestimates the total cost of mining and ignores the difference in ecological impacts between different mine design alternatives. With growing interest in sustainable development, the mining industry is under increasing pressure to operate not only based on economic and engineering principles but also on principles of sustainability. Therefore, estimating ecological costs of mining and considering such costs in the mine design process is an important step towards reducing ecological impacts at the design stage. The objective of this paper is to quantify the ecological costs of open pit coal mining and to demonstrate the influence of such costs on the ultimate pit design. The ecological costs of mining are estimated based on the areas and types of land damaged by mining activities and the carbon emission from energy consumption. Four major components of ecological cost are identified, namely, lost value of direct eco-services, lost value of indirect eco-services, prevention and restoration costs, and the cost of carbon emission from energy consumption. Necessary equations are given for estimating these costs. An algorithm is described for ultimate pit optimization in coal deposits with near-horizontal coal seams. A case study is presented in which the ultimate pits with and without ecological costs are optimized and compared to show the influence of ecological costs on the pit design outcome.

Aug 1, 2013

By Marie-France Caille, Carl Caumartin

"Audrey Resources' Mobrun Mine is located in Dufresnoy Township some 30 km to the northeast of Rouyn-Noranda. The Mobrun tine deposits consist of two major massive sulphide lenses; the newly discovered 1100 lens located 450 m south of the Main zone, and one ntellite lens, the 850-870-930 complex.The 1100 lens is hosted in a large pyroclastic unit bounded to the mouth by rhyolite and andesite flows and by a thick rhyolite unit to the art h. stratigraphically belon the three lenses. It consists of approximately 15 Mt of massive sulphide, of which 10.4 Mt are of economic ade. The Main lens lies comformably above thick rhyolite flows, ecciated and pyritized by the sulphide horizon, and is overlain by ttercalated ash tuffs and rhyolites which host the over-lying satellite ns. The Main lens consists of 3,3 Mt of massive sulphide, of which 523 000 tgrade0.80% Cu, 2.44%Zn,30.19 g/t Ag, and2.2 g/t Au he richer satellite lens (180 000 t) is part of the same volcanic stem and resulted from a resurgence of hydrothermal activity. ructure played a role in the final geometry of the deposits but did not eatly affect the volcanogenic and stratabound nature of the lens. Total production since the start of operations in 1985 amounts to 58 000 t and is restricted to the Main lens. Production from the 100 will come onstream in 1992 as ore reserves from the Main and e satellite lenses are exhausted.RESUMELa Mine Mobrun de Ressources Audrey inc. est située dans le mton Dufresnoy, a quelque 30 km au nord-est de Rouyn-Noranda. lle comprend deux lentilles de sulfures massifs d’importance majeure ~i sont les lentilles 1100 et Principale, et une lentille satellite qui est complexe 850-870-930.La lentille 1100, la plus ancienne, est contenue dans une épaisse 1ite pyroclastique bordée, au sud, par des coulées de rhyolite et d’andésites, au nord, par une épaisse unité rhyolitique. Cette lentille contient environ 15 Mt de sulfures massifs dont 10,4 Mt à teneur économique. La lentille Principale repose sur d’épaisses coulées rhyolitiques brechifiees et pyritisees à proximité de l’horizon de sulfures; elle est recouverte de tufs a cendres et de rhyolites interlitees qui contiennent la lentille satellite. La lentille Principale est constitute de 3,3 M t de sulfures massifs dont 1 523 000 t sont économiques avec une teneur moyenne de 0,80% Cu, 2,44% Zn, 30,19 g/t Ag, et 2,2 glt Au. Faisant partie de ce second épisode volcanique, la riche lentille satellite (180 000 t) temoigne d’une recrudescence de l’activité hydrothermale. La structure joue un rôle important dans la géométrie finale des dépôts mais ellen' affecte pas, de fa~on significative, la nature volcan génique des lentilles. Depuis le début des opérations, en 1985, la production totale est d’environ 568 000 t, provenant essentiellement de la lentille Principale. La mise en production de la lentille 1100 est prévue pour 1992, alors que les réserves des lentilles Principale et Satellite seront probablement épuisés."

Jan 1, 1990

By D. Sagara, V. G. Makhado

"A model based control strategy was implemented at Loulo Gold Mine in Mali, to stabilise the thickener underflow stream density. This stream acts as the feed to the leaching circuit. pH control of the leaching circuit was integrated with the model-based controller due to slow process dynamics that are not suited to PID control. The controller performance was quantified over a period of 6 months, and was compared to the performance before implementation. The model based controller reduced process variability for both thickener underflow density and pH considerably, and resulted in a reduction in flocculant and lime consumption of 9.32 and 6.55%, respectively. INTRODUCTION Reagent consumption in gold processing plants significantly contributes to the total operational costs. In a typical Carbon-in-pulp (CIP) circuit, the reagent consumption associated with leaching, adsorption, elution and regeneration contribute to approximately 15% of the total operational costs (Stange, 1999). At Loulo Gold Mine, the reagent consumption associated with leaching, adsorption, elution and regeneration contributes to 6% of the total operational costs. As such, a reduction in reagent consumption will present a significant opportunity for savings on operating expenditure. Variability in feed ore characteristics results in continuous changes in steady state operating regions, which presents process control challenges as a result of the long residence times in some of the process units associated with gold processing plants. Overdosing often occurs in the presence of process variability to ensure safe operation and to maintain recovery targets. As a means of reducing reagent consumption and accounting for significant changes in the feed to gold plants, some of the plants have resorted to improving their process control strategies around their circuits. This paper focuses on the implementation of a model predictive based controller at Loulo Gold Mine on their thickener and Carbon-in-leach (CIL) tank to: •,stabilise the thickener underflow density, and •,the CIL tank pH."

Jan 1, 2017

By T. H. Patching, D. F. Coates

The Sub-Committee on Rock Classification, Canadian Advisory Committee on Rock Mechanics, has evolved a classification of rocks which should prove useful in studies of rock mechanics. Considered in two stages -actual rock substance and rock mass -the five-point classification involves the geological name of the rock, the rock strength and rock deformation, and, in the second stage, the gross homogeneity of the rock mass and the formation continuity.

Jan 1, 1968