Search Documents

By Monette J. C, Nulty J. H

High temperatures and pressures are required to obtain acceptable stripping rates. Higher chemically induced stripping rates could reduce the need for higher temperatures which lead to cyanide losses. The higher rates could lead to lower carbon inventories and higher gold production. This paper reports laboratory and continuous test unit data which strongly suggest that the preceding can be achieved. New stripping agents demonstrate efficient stripping under conditions of cyanide depletion such as after carbon acid washing. Stripping times for gold and silver can be reduced by at least half compared to caustic cyanide through the use of these novel substances.

Jan 1, 1991

By E Kunz

Decreasing the gas content in the worked seam by degassing before the start of winning has proven its worth in some areas of German hard coal mines. On the one hand, it removes the risk of gas/coal outbursts and on the other hand it reduces the gas inflow into the longwall. The underground experiences of the last 30 years have led to a æhit listÆ of coal seams with respect to their suitability to predegassing. Trials in the DMT laboratory and also results gained in the deposit show that the suitability of a seam for predegassing depends on its rank. In seams with volatile matter of 20 - 30 per cent, high efficiency ratings are achieved as a rule, with lower ratings both in seams with lower and with higher content of volatile matter.If the rock pressure is unusually high, the efficiency rating of the predegassing is lower, even in seams which would normally be suitable for this process. Under unfavourable conditions, for example below or above residual pillars, in-seam boreholes cannot be drilled successfully and the method is not practical. But if the worked seam was already stress relieved, the predegassing has an optimal efficiency. Latest investigations show that the distance between the in-seam boreholes can be extended. But in that case, the time necessary to reach the same reduction of the gas content increases considerably.

Jan 1, 2005

By Wright S, Jorgensen F. R A

The reaction between lead sulphate and a number of base metal sulphides (galena, sphal- erite, chalcopyrite and synthetic pyrrhotite was studied as a means of desulphurizing lead sulphate containing fumes and residues to levels acceptable as ISF feed. The reactants were mixed with 50% zinc oxide to act as a "basket" to contain the molten products of the reaction and pressed into small briquettes 20 mm in diam. Factors such as temperature, time and the composition of the atmosphere were investigated. Using the PbS/PbS04 system as an example it was shown that the reaction became rapid above 800¦C and that both sulphur dioxide and oxygen in the atmosphere were detrimental to achieving low sulphur in the product. In an inert atmosphere all the sulphides when roasted for 1 h at 1000¦C gave results corresponding to the elimination of more than 95% of the sulphur in the reactants. Leach plant residues were considered for use as the "basket" material. It was shown that the residual sulphide and sulphate components of the residues underwent similar reactions to those experienced by the pure systems.

Jan 1, 1987

By R A. Pax

Heavy machinery such as AG and SAG mills generate a significant amount of noise due to the processes that are occurring inside them. From an environmental perspective, the level of noise generated is a significant occupational safety hazard. However from a technical perspective the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of the primary comminution tumbling mills. Traditionally, the use of perfect mixing has been assumed when modelling the operation of AG/SAG mills. If this were true then the acoustic emissions from AG/SAG mills would be uniform along the length of the mill. Experimentally this has been found not to be the case. From another perspective it should not be the case because of the different conditions existing at the feed end compared to the discharge end. This paper presents the results determined by non-contact acoustics and their analysis in terms of understanding of the mechanisms occurring inside a mill.

Aug 8, 2011

Tholeiitic metabasalts comprise at least five geochemically distinct mafic volcanic associations of Late Palaeozoic age within the Gympie Province, southeast Queensland. Geochemical features indicate that parental magmas of the various metavolcanic suites were generated in contrasting tectonic regimes, although each of the suites shows some affinities with eruptives from convergent plate margin settings.Basalts from the Highbury Volcanics of the Gympie Group are island arc tholeiites (IAT) formed during an immature stage of eruptive activity in an intra-oceanic arc. They are unique among the analysed metabasites in possessing high Zr/Nb (Zr/Nb - 30) and very high Ba/Nb, and as well as low Ti/V, Ti/Zr and Ti/Y. These features are explicable solely in terms of contributions from a depleted, convecting upper mantle source, and large ion lithophile element (LILE) enriched fluids ascending from subducted oceanic crust.

Jan 1, 1990

For the last decade Australia has been the leading exporter of both steam and coking coal. In the ten-year period 1989 - 1998 steam coal exports increased by 93 per cent and metallurgical coal exports increased by 50 per cent. However, profitability of the steam coal sector has been disappointing. The coking coal sector, especially the hard coking coal segment, has fared better but its profitability was more because of its ability to maintain relatively high prices rather than its inherent productivity. Until quite recently the Australian coking coal sector was widely expected to be able to maintain this comfortable state without undue effort for the three major æpartnersÆ; the companies, the State Government and the unions. But coking coal could now be heading down the path followed by steam coal that ends with long-term over-supply and, despite steady improvements in productivity, poor profitability. Steam coal entered the ænewÆ era of long-term over-supply some years ago. Over-supply was due to the rapid increase in production in Indonesia, often from new mines and Australia. AustraliaÆs production rise was underlain by the apparent belief that the best way to lower costs was to increase production. In the first couple of years costs didnÆt fall much but the additional tonnage was sold at lower and lower prices into the spot market. By mid-1998 the difference between the contract price set with Japanese utilities and spot sales was often in excess of $US12 per tonne. Japanese contract prices and tonnages have since fallen significantly. Steam coal has moved from being a product to being a commodity. Any profits are due more to the low Australian dollar rather than inherent mine productivity. Seaborne coking coal trade has been dominated by Australia, Canada and the USA, with the USA becoming less competitive. Unfortunately, when the Queensland capacity expansion was well down the pipeline, the Asian financial crisis occurred and the Japanese economy entered what appears to be a long-term recession. Contract prices fell 18 per cent, tonnages decreased and some mines have been reclassified as supplying lower priced coking coal. The paper analyses past and expected future trends in labour and mine productivity, rail freight and FOB export port cash and total costs of the Australian steam coal and coking coal sectors and discusses the market outlook for Australia. The future economic viability of the industry is analysed and discussed in the light of the rapidly changing global environment.

Jan 1, 2000

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

A practical approach has been developed for the design of both grates and pulp lifters. It is based on: an appreciation of the process interaction between grates and pulp lifters, an interpretation of mill charge structure as it relates to discharge through grates, and an analysis of pulp and solids flow in pulp lifter channels. This approach can be used to improve the overall discharge effectiveness of AG and SAG mills.

Jan 1, 2000

The long term viability of a mining company is dependent on the success of its capital investments. Due to the specialised nature of the design, engineering and construction of large projects the management is often contracted to an outside organisation. This paper is a review of the phases of the relationship between Client and Contractor. A rationale is developed upon which the selection of a Contractor can be made. Subsequently, the key aspects of the Client/Contractor relationship are reviewed with reference to completing the project on time within budget. The aspects discussed include Contractor management systems, qualifications of key personnel, definition of scope of work, industrial relations, project control and Contractor remuneration.

Jan 1, 1983

By Maslov LA

We have considered the following characteristics of the crust and upper mantle of the Pacific Belt: seismic wave velocit> anomalies, mechanical stress and shear deformation rate fields, heat flow and the pattern of metallogenic provinces of the Belt. It has been noted that there exist certain regularities in distribution of the above mentioned geophysical characteristics and metallogenic zones within the Belt, displayed by prevalence of the lithophile elements in the Asia-Australian part of the Belt, and of the chalcophile ones within the American part.

Jan 1, 1995

By L Lagoeiro

The samples studied in this paper were derived from the iron oxide facies of iron formations (IFs) of the Quadrilßtero Ferrffero, south-eastern Brazil. The rich-iron oxide varieties of the IFs can be regarded as Fe-O systems because they consist predominantly of aggregates of haematite and magnetite crystals. The study was based on carefully selected samples in which magnetite crystals occur as isolated large crystals set in a matrix of haematite grains. Optical microscopy and an electron microscope equipped with an electron backscattered diffraction (EBSD) system were used to investigate the microstructural and crystallographic relationships involved in the phase transformation between magnetite and haematite. The magnetite crystals in the IF samples are partially transformed to haematite and this process is also known as martitisation. This transformation occurs along the crystallographic planes {111} of the magnetite producing a characteristic triangular pattern of interlocking lamellae of transformed haematite crystals that are oriented parallel to octahedral plane {111}. This new generation of haematite is referred to martite because of the martitisation process. EBSD analyses show that the magnetite and the new haematite crystals, martite, share crystallographic planes of highest atomic density, eg {111} and (0001), respectively, possibly due to the ccp and hcp atomic arrangement of the two crystals. Stereographic projections of these two planes therefore coincide when the maxima of their poles are plotted. However, the crystallographic orientation of the haematite crystals in the matrix shows maxima of (0001) poles that do not coincide with those of {111} planes of magnetite. Consequently, it is concluded that the direct transformation to haematite crystals retains the crystallographic orientation memory of the former magnetite crystals, possibly due to the similar manner whereby their atoms are packed together in the crystal structures. On the other hand, no such relationships are observed between magnetite and haematite crystal in matrix. This suggests that haematite grains in the matrix may have been formed by other processes rather than those involved in the iron oxide transformation observed within the magnetite grains.

Jan 1, 2008

Wetherstones gold deposit is located just east of the township of Lawrence, in the Otago District of the South Island, New Zealand. The paper will describe aspects of the mining and exploration history of the Wetherstones gold field, current knowledge of the geology of the deposit, and speculate on possible outcomes of exploration in the modern era.   As at the famed Gabriels Gully situated nearby, most of the Wetherstones gold is/was contained in, or recycled into modern drainages from, the Blue Spur Conglomerate (æBSCÆ). The BSC is the basal member of a wedge of auriferous non-marine sediments of latest Cretaceous age which are tilted against the Tuapeka Fault Zone, a structure of regional dimensions. In particular mineralisation of elevated grade (which cannot yet be reliably estimated) appears to be concentrated in an elongate basement depression (ægutterÆ) of width around 100 m, variable thickness to a few metres, and axial length in excess of 500 m. The gutter plunges from the base of alluvial mining (where it has been partly exploited by underground methods) to depths of more than 100 m, beyond which it remains open and untested.   The prospects for a revival of mining at Wetherstones depend upon confirmation of what is here inferred to exist, and the discovery of additional gold. The economic prospects of the project however are enhanced by what is known or indicated of the geographic location, and anticipated geologic, mining and metallurgical characteristics of the mineralisation, and consequent anticipated environmental management issues.   The recognition of gold contained in pyrite in the BSC represents an upside to project economics which has never previously been evaluated. The Wetherstones Basin covers more than five square kilometres in areal extent. There is no modern exploration record of the majority of this area, leaving open the prospect of the discovery of additional gutters, and primary mineralisation in the underlying schist.   Australasia Gold Ltd has embarked on a program to reassess the potential resources of the Wetherstones gold mineralisation, and to evaluate the feasibility of mining.

Jan 1, 2004

The Permian coal in the Muja Coal Measures of Collie Basin of Western Australia has a subdued lustre because of the fine laminations of lithotypes, and the dominance of dull and dull banded lithotypes with minor bright, bright banded and fusinous types. The maceral composition of the coal is variable, however the macerals of vitrinite and inertinite groups dominate and the exinite and mineral matter contents are low. The lithotypes have low concentrations of trace elements and the boron concentration is between 10 - 100 ppm recorded only from the dull lithotypes. On the basis of organic petrology, the inter-seam sediments, flora and the very low concentration of boron, the depositional environment postulated for the coal is braided, fluvial and fluvio-lacustrine with marked fluctuations in the water table. The low water table in the environment accounts for fusain and inertodetrinite in the coal.

Jan 1, 1996

By Lightfoot BW, Foo KA, Conochie DS

Aberfoyle Limited operated a matte fuming pilot plant, incorporating a SIROSMELT furnace in 1980/81. This plant was a significant advance in both smelting and tin extraction technology. Important design, construction and commissioning aspects are discussed and some of the key points to emerge from this phase of the work are reviewed.

Jan 1, 1984

The Ladolam gold deposit, located on Lihir Island in PNG, is one of the largest known epithermal gold deposits, with a resource of over 37 million ounces. The deposit is characterised by a telescoped porphyry-epithermal system 2-rich sulphidic hydrothermal fluids capable of transporting significant quantities of gold, and the sudden change from porphyry to pithermal conditions caused by removal of the volcanic edifice. As magmatic ore fluids breached the surface, cool surface waters (seawater and/or meteoric) acted as a diluent. Although no other deposit is known with comparable geological characteristics and size, positive features that may be looked for in exploration for other like-deposits elsewhere include magnetite-rich alkalic volcanic rocks, large carbonate haloes, and presence of phreatomagmatic breccias. New discoveries may be recessive or undercover, due to the quartz-poor nature of the alteration.

Jan 1, 2002

Suppression of the explosion of the world population and the surprising increase of waste and emissions are major targets confronting mankind in this century. Recycling and waste minimisation are key words for sustainable development in a highly industrial society. The argument is really whether or not recycling done well is the solution to the environment problem for the following generation. If energy is not necessary in the recycling, all materials have to be recycled. The greatest interest among the environmental issues is the regulation of CO2 gas emission. It must be recognised that it is not possible to completely renew expended energy. Some of the recycling systems currently used are thought to increase the load on the environment rather than to be beneficial. Although metal industries have consumed tremendous amount of energy and discharged a large quantity of CO2 and solid waste, the metals have supported a high quality of life. The metal production industries such as the iron and steel industry and the non-ferrous metals industry can work well recycling of not only metals but also other materials without consuming more energy. Waste plastics, for example, are use as a reductant in a blast furnace. The role of metallurgical industry in the recycling-based society is introduced in the present paper to recognise how the metal industries can contribute recycling and waste minimisation.

Jan 1, 2002

Applications of chlorine metallurgy to the extraction of metals often result in the production of volatile metallic chlorides, most of which condense directly to a solid phase at one atmosphere pressure. A stirred bed condenser suitable for th

Jan 1, 1980

By Noreen D

At Bougainville Copper Limited comparison testwork was conducted between "horizontal" cycloning and conventional vertical cycloning. Horizontal cycloning reduces circulating load and allows increased ball mill throughput. Cyclone efficiency is the same or better as a result of the reduction of fines short-circuiting to the underflow. Operationally, horizontal cyclones are less likely to suffer from blocked spigots and high cyclone feed pump sump levels. Cyclone feed pumping power is reduced. High horizontal cyclone underflow density provides the option to optimise grind by manipulating water addition to the ball mill feed.

Jan 1, 1988

By P Elliott, D Pershke

In a minerals processing context, sustainability is about using natural resources more efficiently to achieve maximum economic benefits with minimal environmental impacts. It embodies five overarching themes, which the paper will illustrate with practical examples from Australian minerals processing plants. These are:resource utilisation and materials efficiency,process waste reduction and enhancement of co-product values,reduction of water use and impacts,reduction of energy requirements and greenhouse gas emissions, andenhanced control of minor elements and toxic materials. Sustainability could be embedded profitably in minerals plant design in three dimensions: 1.technology,2.design, and3.operations. This presentation discusses a set of principles that could be applied to minerals processing technologies and provides an outline of sustainability assessment and opportunities evaluation tools. The application of the tools is illustrated through a case study by analysing a suite of nickel processing technology routes. The analysis reveals that current generation of nickel processing technologies do possess real potential to emerge as sustainability champions in integrated processing of nickel ores and concentrates, if they are designed, engineered, and operated for sustainability and adapted effectively to site specific constraints and opportunities. The paper will address data gaps and uncertainties regarding the impact of scaling up of pilot-plant performance, and provides strategies to overcome them.

Jan 1, 2006

By Eggleton T, Taylor G

The lateral and vertical distributions of gold and a wide range of other elements in the regolith, close to Au and Cu mineralisation have been investigated at Goonumbla, NSW. Open cut mining has exposed deeply weathered profiles which have been used for this investigation. Determination of secondary mineralogy and micromorphology of profiles have facilitated the broad interpretation of processes that determine element mobility and dispersion from primary mineralisation as a result of weathering. This in turn has led to better interpretation of geochemical data and enhanced understanding and knowledge of regolith geochemical processes which are invaluable in the formulation of improved exploration Procedures.

Jan 1, 1997