Search Documents

By J Knecht, R Klymowsky, E Burchardt

The wide spread introduction of SAG mills into grinding circuits 20 years ago was the last development which had a major impact on the design and economics of comminution circuits. Single SAG mills were able to replace batteries of high maintenance and cost intensive crushers in order to achieve high throughput operations. Today, where the head grades of gold and copper ores are falling, there is again a strong need for a significant breakthrough to reduce investment and operating costs as well as improve metal recoveries. High-pressure grinding rolls is the new technology available to meet this challenge. HPGRÆs are state-of-the-art in several mining and minerals applications such as the grinding of iron ores and concentrates, and diamond bearing ores. Reasons for their success in these industries are overall cost reductions and improved product properties achieved by the application of high compressive forces. But these ores are relatively soft, with unconfined compressive strengths up to 150 Mpa.

Jan 1, 2000

By D M. Weedon

This paper introduces a novel roll crusher design, which incorporates non-cylindrical crushing rolls. The use of non-cylindrical rolls enables the crusher to achieve a greater reduction ratio than is possible with conventional roll crushers. Referred to as the NCRC (non-cylindrical roll crusher), the new crusher incorporates two rolls comprised of an alternating arrangement of plane and convex or concave surfaces. The two rolls are complementary and arranged so that when they rotate the convex and concave surfaces of each roll are substantially opposed. With the rolls rotating in opposite directions at the same speed, this arrangement produces a gap between the rolls that remains approximately constant. Discontinuities on the roll surfaces provide improved angles of nip, which increase the probability of larger particles being drawn into the crusher. Initial tests on a scale prototype of the NCRC have indicated that reduction ratios exceeding 10:1 are achievable.

Jan 1, 2000

By X Yang, T Zhang, Z Li, Z Yan, M A. Williams, S Qin, P Wilson

Continuous development of complex new steel grades to meet the ever-increasing demand of high performance causes recurrent issues in steel continuous casting such as surface quality defects (eg cracks, depressions, deep oscillation marks) and productivity challenges (eg faster casting, near-net shape casting). Continuous casting of steel is a highly successful metallurgical process. Much of this success can be attributed to the performance of the casting powder that is added to the top of the mould, creates a liquid slag pool as it is heated, and forms a slag film between the watercooled copper mould and steel shell during its passage down the mould. Mould powder selection is a compromise between the conflicting requirements of heat transfer and lubrication. In an EU RFCS (Research Fund for Coal and Steel)-funded project, various techniques are developed to offer the opportunity to adapt the slag film to meet the conflicting needs in different parts of the mould such that mild cooling can be generated in the meniscus, mid-broad face or corner areas whilst maintaining lubrication and offering higher cooling rates in other areas of mould. This has significant potential to address the industrial issues in product quality and productivity of continuous casting. This paper reports, as part of the EU RFCS project, the determination of crystallinity and porosity in slag films for casting challenging and innovative steel grades using new methods. In comparison with the methods such as X-ray powder diffraction (XRD) analysis and optical microscopy / scanning electron microscopy (OM/SEM) analysis that are currently adopted by the industries, EBSD (electron backscatter diffraction) has been employed to determine the crystallinity of the slag films taken from industry casters. X-ray computed tomography (XCT) plus 3D image reconstruction has been used to determine the slag film % porosity with pore volume, pore size distribution, and pore location, which can be linked with the performance of the slag films during casting different steel grades.

Jun 19, 2024

To discuss this relationship both the problems of the mechanisms of ore accumulation and the origin and cause of volcanism must be faced. Volcanic activity is associated with hydrothermal activity but the causes of volcanism are inseparable from the problems of the origin of magmas generally. To be more in accord with the inevitable reaction between water and silicates at high temperature, it is suggested that reconsidera- tion be given to the role of water in magmas such that our general concept of magmas becomes one of hot hydrous pastes rather than melts with water in them. It is claimed that a general concept of magmas as gelatinous hydrosilicate masses is a far better assumption because the rheological and diffusive properties of such materials enables an adequate explanation of a greater number of observations. It is consistent with the mergence of magmatic and metamorphic rocks and requires low to modest temperatures at the time of liquifaction allowing convergence with mobilised and disturbed sediment masses. The physical and chemical properties of both wet sediment pastes and magmas envisaged as hydrolised silicate masses are entirely dependent on the enormous internal surfaces of their disordered solvated components. Mechanical disturbance, such as reliquifaction

Jan 1, 1974

New Caledonia, Norfolk Island and northern- most New Zealand lie on a long, narrow, ridge system, the Norfolk Ridge System, which is sit- uated in the centre of a geologically complex region of ridges and basins between Pacific Basin oceanic crust and continental crust of Australia (see Eade, 1987).

Jan 1, 1987

By Kolarczyk M

When controlling the ventilation process in a deep mine some knowledge of the sensitivity of the air volume output to changes in the resistances of network side branches is of great advantage.Sensitivity is taken to mean the limit of the differential quotient AV /ART where AV. is the change in air output in the i--h side branch caused by a change of resistance LI R in the r-th side branch. A method Is presen- ted for determining any arbitrary co- lumn of the sensitivity matrix. A network interpretation of this met- hod was developed in which an ancilla- ry network additional the basic network is constructed and solved, giving an analysis of the sensitivity signs de- pending on the structure of the network.

Jan 1, 1988

By Smit J. G

Following an increase in the number of methane ignitions in South African coal mines a new ventilation system was developed. The "Hydravert" system conceived in late 1979 for use in low seam coal mines, where the bord and pillar method of working is used, has been extensively developed to include applications for mining seams up to 4.5 metres high. A brief history of the development is supplied including some of the pitfalls encountered in the hydraulic equipment design and selection.

Jan 1, 1988

Kamhalda is located within the Yilgarn Craton of Western Australia, specifically in the Norseman - Wiluna greenstone belt. Numerous nickel sulphide deposits have been mined at Kambalda with I I mines currently operating. For several years, a program of in-mine geophysics has been operating at Kambalda, with downhole electromagnetics (UHEM) one of the key techniques used. Three case studies illustrating the uses of UHEM in mines are presented here. In the first example, the Helmut South deposit was discovered as the result of an extensional exploration program. The first drill hole in the program intersected ore width and grade mineralisation at around 760 in depth. Two subsequent holes intersected subgrade mineralisation. DHEM surveys were completed in each of these three holes, with anomalies recorded indicating that a large conductor was located directly south of the first hole. The next hole intersected this target, for an intersection of 21.6 in at 3.5 per cent Ni. DHEM continued to play a role as the exploration program proceeded, providing drill hole targeting based on anomalous responses recorded in each drill hole. In the second example from Carnilya Hill, old drill holes were surveyed with DHEM in order to search a large section of prospective contact for massive ore pods. An off-hole anomaly was detected and subsequent mining discovered a small but high-grade pod of ore which was extracted for a considerable profit. Carnilya Hill has limited reserves and discoveries such as this, assist in keeping the mine operating. In the third example from Victor, a program of drilling intersected thin ore profiles in an interpreted flanking position. Without massive ore close by, these intersections probably do not constitute economic mineralisation. DHEM surveys of three holes did not detect any conductors. The area is now regarded as sterilised of significant massive ore and exploration efforts and dollars can be focused in other areas. These three examples demonstrate the type of successes that can he achieved through the use of DHEM.

Jan 1, 1997

The reasons for selecting two stage pebble milling in preference to conventional methods of grinding are discussed. Commissioning of the first section was completed in October, 1969. Improvements in both the operating and engineering aspects were then incorporated in the section commiss ioned in March, 1971.

Jan 1, 1975

The capabilities of the three 61R and one 81R Robbins Raiseborers currently in use at Mount Isa are defined. Their applications in the development of ventilation and hoisting shafts, orepasses, escape routes, fill passes etc. are described and possible future uses of these and newer raiseborers at Mount Isa are examined. Problems associated with the use of raiseborers, together with ways of overcoming them are discussed. The impact of raiseborers on the mining operation is assessed in terms of new approaches to design and development, safety, cost and manpower efficiencies.

Jan 1, 1974

UNLIKE coal mines, in which some form of artificial ventilation is rendered necessary by gases given off by the material mined and is also enforced by the mining laws of all countries, metalliferous mines have almost entirely relied on natural ventilation, viz., that due to the difference in temperature between the outside atmosphere and the mine air. In small mines natural ventilation has proved sufficient, but as mining proceeds at a greater depth, and where large ore bodies arebeing attacked the writer is of opinion that some means of artificial ventilation will be rendered necessary if only from an economic standpoint.The Broken Hill Proprietary Mine was one of the first metal mines to introduce a scheme of artificial ventilation on a large scale. In order to render the working conditions of the semi-friable stopes of Block 12 and the lower levels of Block 11 morecomfortable for the men at work in these places, in 1903 it was decided to install a fan to thoroughly ventilate these stopes. The fan chosen was a Capell double-inlet fan beltdriven from a steam engine: this engine was later on replacedby an electric motor. The fan was put in commission at the latter end of 1904; its principal dimensions are as follows: Length 6 ft. 6 in., diam. 7 ft., diam. of inlet 4 ft. 7i in. The fan is reversible, though this is a rather misleading term, asthe direction in which the fan blades revolve is not reversed...

Jan 1, 1921

The Olympic Dam Project constitutes a major resource of Copper and Uranium and has been under intensive evaluation since the discovery in 1975.A 500 metre deep rectangular shaft has been sunk into the deposit and this has been followed by 8400 metres of level, incline and decline development. 5 surface ventilation raises have also been constructed.Large scale trackless equipment is used to carry out the development, and productivity statistics are given.The paper describes the functionalised system used in the development program and discusses the maintenance support, and services required to carry out these works.The objectives of the Exploration Development program and the satisfactory results obtained from this work are also discussed.

Jan 1, 1985

By N Burgio

Block cave mines are often thought of as rock factories where high volumes of production are mined from a fixed area suggesting little requirement for geological input and control. Yet caving operations have peculiar and specific technical requirements from prefeasibility through to post-mining reconciliation. Whilst essential elements such as resource definition, geological interpretation and sampling strategies are common to all mining methods, planning for a block cave requires a different emphasis and philosophical approach in how we deal with these issues. We will examine why a geoscientist’s input is critical towards the successful planning, design and monitoring of a caving operation.

Aug 22, 2011

SPOT imagery acquired in May 1986 of the areas that include the Dugald River lead-zinc lode, northwest Queensland, Australia and the Ngwenalekau copper deposit, Botswana has been evaluated and compared with LANDSAT MSS imagery of the same areas. The data have been processed using band combinations, band ratioing, principal components analysis and classificatory techniques and the outputs compared with those of geobotanical, geochemical and biogeochemical data as well as geological information. For both study areas the image processing techniques cited have successfully distinguished discrete vegetation associations related to discrete surficial and bedrock geological units; and, notwithstanding the sharp contrasts between the nature of the geobotanical anomalies that in both areas occur over mineralised bedrock in Proterozoic sedimentary sequences, they have successfully identified the areas of anomalous vegetation over the mineral deposits. Greater vegetational and geological detail is revealed than on outputs generated from LANDSAT MSS data [see Cole, 1977, 1982(a) and (b)]. The additional information yielded by SPOT imagery compared with LANDSAT MSS imagery results from its greater spatial resolution - 20 metres as against 79 metres - and from ti fact that the three SPOT MSS spectral bands - 0.50 0.59um, 0.615-0.68um and 0.79-0.89um - respectivelc cover those sections of the electro-magnetic spectrum in which leaf pigments, notably chlorophyll, absorption for photosynthesis and leaf cell structure strongly influence reflectance. This accords opportunities for the detection of reflectance aberrations caused by stress due to drought and/or metal toxicity as well as for the identification of anomalous vegetation communities of moderate sizr These cannot be accurately discriminated on LANDSA I MSS imagery on which only very large geobotanical anomalies like that over the Lady Annie phosphate deposit in northwest Queensland [Cole, 1977, 1984; Cole and Owen-Jones, 19771 can be detected.

Jan 1, 1988

Refractory gold concentrates and their roasted products have been examined by mineralogical and chemical methods, and the distribution of gold in the tailings after leaching has been Investigated.

Jan 1, 1989

This paper outlines the aims, objectives and means by which a life of mine land use plan was established for Comalco's bauxite mine at Weipa. Comalco realises the need to strategically plan for future mining activities and still minimise the impact of operations on the natural resources of the region. With this realisation long-term forward planning has been implemented to improve the Company's ability to select future sites for mining, industrial use, agriculture, town expansion and conservation purposes.The knowledge of mineral, water, soil and animal resources has expanded dramatically in the past decade. During 1990 Cornalco purchased Geographic Information System technology which has allowed previously collected resource data to be presented in map form. These maps as part of the Life of Mine Land Use Plan are both information based and strategic which can be efficiently updated. The maps allow a broad audience from engineers, geologists, environmental scientists and site managers to government officers and the general public to comprehensively view and scrutinise the operations.

Jan 1, 1992

The Antarctic Peninsula consists of accretion complex sedimentary and volcanic rocks, talc-alkaline magmatic are rocks, marginal basin sediments and extension-related alkali basalts, dominantly of Mesozoic to Cenozoic age. Metallic minerals have been recorded at "250 localities but two thirds of these are innocuous occurrences of Fe+Cu accessory minerals. The remaining -70 localities are related to hydrothermal mineralization processes. Metallogenetic associations identified are: vein and breccia-hosted Fe+Cu+Zn+Pb+Mo or Fe+Cu+Mo+Mn, shear-hosted Fe+Cu, volcanogenic Fe+Cu and pegmatite-hosted Fe+Cu+Mo+Mn. Anomalous Au, Ag, As, W and Sb also occur but are not of economic interest. Metallogenic zoning is unproven and genetic models are uncertain, possibly involving volcanogenic, epithermal to hypothermal vein and porphyry-type systems. Substantial field and laboratory studies are required to understand distribution and Genesis.

Jan 1, 1987

This paper summarises the results of a study carried out for the Sustainable Minerals Institute, University of Queensland, aimed at identifying the major water-related issues facing the minerals industry internationally and the research required to support the development of practicable solutions. An overview is given of the sources and uses of the worldÆs water resources and of the regional and global sustainability of water supply and management. Agriculture is the worldÆs major user of water; it wastes more water than the minerals industry uses. Water reform and its potential impact on the minerals industry are discussed with particular reference to Australia and South Africa. The sources, uses and management of water on mine and processing sites are outlined. Particular attention is paid to the importance of groundwater as a source of often saline water that can be used in mineral processing and for other purposes. Aquifer storage and recovery has the potential to help conserve water resources. Generally, the major uses of water on mining and processing sites are for mineral processing and refining and for the associated tailings disposal. Water consumption for these purposes may be reduced by recycling process water, using saline water, paying close attention to water management, thickening tailings and using techniques such as dry stacking and paste. A change in the minerals processing paradigm in respect of water use could come through research into new, improved and less costly dry processing techniques. The treatment of mine and processing water will be required increasingly before water is reused, stored, discharged or sold, and before sites are decommissioned. Research and development are required to reduce costs and develop new treatment methods. Mine closure and decommissioning raise a number of long-term water issues requiring continuing generic and site-specific research and development.

Jan 1, 2003

By Peck WH

For many years it was realised that the methods used for unloading concentrates at Port Pirie were inefficient and labour intensive, therefore, when a decision was reached to standardise the east-west rail link from Sydney to Perth, the opportunity was taken to consider entirely new schemes for the handling of concentrates at Broken Hill and Port Pirie. After considerable testing and investigation, it was decided to install a completely new concentrates handling plant incorporating a tippler at Port Pirieòto replace the previous long established methods of unloading and dis- tributing concentrates to the operating plant.and the shipping berths. To achieve this, wagons of concentrates from the various mines are marshalled in a set order at Broken Hill and conveyed to Port Pirie in 56-wagon trains. On arrival at Port Pirie, the wagons are checked and moved to a position where they come under the control of the automatic wagon marshalling equipment.

Jan 1, 1975

A shift in the present day oil exploration scenario from West Coast can be foreseen keeping in mind peak of exploration in Cambay Basin and fast pace of development in Bombay High and its associated fields by the end of this century. Shifts in exploration from structural traps to stratigraphic traps, techno- logical development to drill in deep waters, improving economic situation for oil ventures and proven oil and gas potential of East Coast basins suggest that Indian oil explorat- ion scene will be at its peak along east coast during early 21st century. Hydrocarbon shows in Poonch and Jawalamukhi in Punjab Basin, improvements in drilling to greater depths, better seismic data aquisition, good source rock potential of Subathus and its equivalents and large geologi- cally mapped structures will reopen new avenues for explorationists. Not much exploration effort has been put up so far in Ganga Basin. Keeping in mind size of the basin, sedimentary thickness involved, presence of algal matter deposited in shallow marine environment & higher hydrocarbon indications warrant active exploration. Gondwanas in India having such a large sedimentary area can not be ignored keeping in view generation and production from the non marine sediments of Kenya, Chad, Sudan, Gadon and China. Gondwanas become all the more important in view of gas production from their equivalents-Karoos in Ethiopia and South Africa. In all, above mentioned changes can be predicted in Indian oil exploration scenario during 21st century.

Jan 1, 1986