Search Documents

By King D

Recent field experiments in the United Kingdom (Buchanan, 1979) have shown that the in-seam technique is capable of detecting a 1m fault in a 3m seam, at a range of 280m and with a resolution of ¦40m. Comparable tests in Australian collieries are proceeding. Although the practicality of an implementation of the technique on a routine basis remains to be demonstrated, the potential of the technique for the prediction of outbursts clearly warrants detailed examination. This potential will,depend, inter alia, on the level and scale of variations in elastic (and anelastic) properties of bodies of coal undergoing stresses associated with mining. Available data, mainly from studies of the seismic properties of gas saturated reservoir rocks, confirm the intuitive view that stress increases give rise to increases in seismic wave velocity and decreases in wave attenuation, markedly at low stresses (as pore spaces close with little resistance) but less so as stress increases. Such increases are of the same order as aniso- tropic effects, but should provide impedance contrast sufficient for detection by in-seam seismic methods. At higher stresses, cracks form within the rock mass. Results from research on earthquake prediction provide some clues to the behaviour of sedimentary rocks sub- jected to large stresses. In particular, the

Jan 1, 1980

By Fourney W. L, Dick R. D

Tests were conducted in plexiglass and Rockite models to determine if crater blasting could be improved by changes in charge geometry or by alterations to the borehole. Circumferential grooves were placed at various locations in the borehole in an attempt to control the initiation site of the crater. Grooves located at or above the top of the cylindrical charge had no effect on the resulting crater. Grooves placed too low in the borehole were successful in controlling the initiation site but the growth of the fracture system was not sufficient to reach the upper surface. Grooves located at a height of two thirds of the charge length were quite successful in that resulting craters were bigger by at least a factor of six than the normal crater. Testing was conducted in Rockite models to investigate charge geometry. Spherical charges in ungrooved boreholes resulted in crater sizes that were three times larger than those caused by cylindrical charges.

Jan 1, 1990

The Golden Valley Volcanic Centre has been recently interpreted as being a combination diatreme breccia pipe and rhyo-dacite flow dome complex of Permo-Carboniferous age that intrudes basement granitoids and sediments of Ordovician-Devonian age. Exceptionally good exposure at the Centre has enabled the relationships between different lithologies to be determined. This, along with petrological studies, has led to a detailed understanding of the geological environment in which the complex formed. Gold, silver and base metal mineralisation have been recently shown to be associated with the Marginal Breccia at the perimeter of the diatreme. Comparisons have been made between the geology and mineralisation in this system and several similar diatremes which also contain gold-base metal sulphide mineralisation.

Jan 1, 1990

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976

By Naik J. S G

The plant practice plays an important role in production and productivity. Men, material and machinery have to be judicially utilised to achieve maximum output with minimum cost. Improvements in technology should be incorporated at an appropriate time and place. The personnel concerned should be properly trained and motivated to receive the changes in machinery and technology. Strict adherence to prescribed parameters, optimum utilisation of man, machinery and operating supplies help in the smooth functioning of the plant and in achieving maximum gains.

Jan 1, 1992

By Liu Q, Siefken T. C, Misra V. N

The bubble size was measured in a laboratory flotation column. The effect of variables such as air flowrate, frother dosage and type, pulp density, particle size and water column height on the bubble size was investigated. The results show that an increase in either air flowrate or pulp density cause the bubble size to increase, while increases in water column height, frother dosage, surface tension or solid particle size cause the bubble size to reduce. Among the frother types tested, MIBC was found to be the most effective in reducing the bubble size.

Jan 1, 1992

By Dunlop JSF

A description of general mining proced- ures and tyre maintenance practice is given with particular reference to tyre mainten- ance facilities and record keeping at Groote Eylandt. Experience with tyre wear on Wabco 85C rear dump trucks is then outlined, concen- trating on wheel camber, wheel alignment, truck speed, tyre pressure, loading and haul road design. T T.1TUnilhTPTTnAT The Groote Eylandt Mining Company Pty. Limited mines and beneficiates sedimentary manganese ores from a series of orebodies occurring in the western part of the island. The island is one of a group on the western side of the Gulf of Carpentaria, about 50 kilometres from the Arnhem Land coast and about 650 kilometres from Darwin. Whilst capacity of the mine is presently 2.3 mil- lion tonnes of product per annum, current production has been reduced to just more than half this figure, due to a general mar- ket recession.

Jan 1, 1982

There are many factors influencing the way in which a mining company disposes of tailings. Some of the more important factors include physical and chemical properties of tailings, cost, availability of dam wall construction materials, type of mining operation, topography and environmental constraints. As a result, the mining industry has seen a diverse and innovative range of disposal methods developed to satisfy the many conditions imposed at tailings disposal sites. This paper discusses a range of tailings disposal methods currently practiced in the mining industries in North America. These methods include various inpit disposal techniques, upstream, downstream and centreline dam construction and zoned earthfill or rockfill embankment construction. The thickened tailings disposal method and the disposal of fine clays are discussed. The importance of improving the depositional properties of tailings to enhance storage capacity, water reclaim, dam wall stability and final reclamation is stressed. It is important that mining companies are made aware of the full range of disposal methods and dam construction techniques available today. Such an awareness will help improve the planning, design and construction of safer and more efficient tailings disposal facilities in the future.

Jan 1, 1989

By Patridge A. C

Hydrocyclones have widespread use as classifiers in applications such as mine fill preparation and coal preparation. A fundamental conflict often exists between recovery of all of the valuable material and maintaining the quality of the product. This conflict is a result of a portion of the feed material passing through the cyclone, effectively without undergoing any classification. This paper describes an investigation, undertaken as an undergraduate project in mining engineering at the University of NSW (Brook, 1994), into aspects of cyclones in which supplementary water injection is used in an attempt to reduce the amount of misplaced fine material reporting to the coarse product and hence improve the overall classification efficiency. In particular, the study concentrated on the effects of different modes of water injection. Two methods of introducing wash water into the cyclone body were investigated. A series of tests were performed on a laboratory hydrocyclone having provision for radial water injection at different levels through small orifices in the wall of the conical section, and a preliminary study was made of the performance of a novel cyclone in which the conical section had walls of a permeable polyethylene, permitting a uniform introduction of wash water over the entire surface.

Jan 1, 1995

By Nemcik JA, Gale W. J

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ

Jan 1, 1992

The geology of an area in north-western New South Wales, bounded by the South Australian and Queensland borders, latitude 32° S. and longitude 14° E. is discussed.The area involved includes sixteen 1:250,000 standard military sheets and covers approximately 96,000 sq. miles.The geology of the Willyama Complex is not dealt with but a small area of metasediments previously included in this unit is separated and a possible correlation with Precambrian to the east is suggested. Torrowangee Group sediments are described and the problem of nomenclature using a glacial implication is raised.Nine areas of proven Lower Palaeozoic sediments are considered and their relationship to the boundaries of the Bancannia Trough outlined. It is possible that some exposures not yet substantiated by fossil evidence may prove to be Lower Palaeozoic rather than Precambrian in age.The sediments of the Lachlan Geosyncline in the area of the Cobar massif are described and new concepts on the age and distribution of some of the established stratigraphic units are introduced. The absence of rocks of Middle Silurian age probably indicates the time of a major orogeny in this area.Lithology, thickness, and distribution of the Upper Devonian sediments is considered and some of the more recently found fish plate localities are listed.Mesozoic sediments occur in isolated areas of Lower Jurassic age and in the Great Australian (Artesian) Basin. A four-fold subdivision of sediments of the basin has been possible in some areas but lack of sub-surface information at present, precludes the possibility of correlation with the type sections in Queensland.Units in the Cainozoic are subdivided and a five fold subdivision of the Quaternary, at present being used throughout western New South Wales, is described.

Jan 1, 1969

By Propser M, Szekely J

Flow maldistribution in the iron blast furnace has been studied analytically by the use of the vectorial form of the Ergun equation and experimentally via packed columns and a cold model of a blast furnace. Experimental results are presented showing the effect on fluid flow patterns of the following types of nonuniformities in a packed bed: the increased voidage at the wall ("wall effect"), the decreased voidage at the interface between layers of materials with different sizes and shapes, and the differences in resistance to flow of bulk regions of a column with different sizes and shapes. The proposed theory is applied to the calculation of fluid flow patterns for these nonuniformities. Velocity profiles, as calculated from these flow patterns, were found to agree reasonably well with experimental measurements obtained via hot wire anemometry techniques for laboratory scale packed columns. Calculated fluid flow patterns are presented for blast furnace burdens which show how flow patterns are affected by (a) coke segregation and (b) the relative differences in resistance to flow between coke and oxide pellet layers. For the cold model study, calculated flow patterns are presented based on photographs of a given burden distribution. The velocity profiles calculated from these flow patterns were found to agree reasonably well with the velocity profiles measured from the cold Model.

Jan 1, 1975

By Savidis G

The characteristics of 'Z' (Back-over run) and 'R' (Reverse) ventilation systems are dis- cussed in relation to their suitability for longwall mining. Experience in European mines has been described as a basis for comparison with Australian conditions. In assessing the merits of each ventilat- ion system, such factors as longwall layout (pillar design, number of headings and gateroad stability), the need for gas drainage and bleed- er systems, as well as the influence of seam dip have been considered relevant. The R system is generally applicable for single and two heading development in seams where gas emission is a less serious problem. In contrast, the lower extraction to development ratio of the Z system (which arises from using three or more heading layouts) is considered more favourable where high gas emission occurs. The Z system provides greater flexibility with respect to the provision of refreshing air at the tailgate end, access of men and materials, installation and retrieval of gas drainage systems and the ability to interchange main- gate and tailgate roadways in cases where roof strata loads are difficult to control, or where cpam in hac an influrnra

Jan 1, 1983

By Bolton G. C

Experiments were conducted to access the feasibility of removing zinc from lead slag by sulfation or chlorination or both. Gaseous sulfation with sulfur dioxide and oxygen released only 50 per cent of zinc even under the most severe conditions. Sulfation with concentrated sulfuric acid by a fast-leach process released 95 per cent of zinc while pug-roasting released a maximum of 78 per cent of zinc. Chloridization with NaCi in the presence of sulfating gas released 50 per cent of zinc, while direct chlorination with chlorine gas and oxygen released 85 per cent of zinc and 100 per cent of lead in a chloride condensate containing little impurities.

Jan 1, 1980

By J Vann, S Jackson, O Bertoli

Ordinary kriging and non-linear geostatistical estimators are now well accepted methods in mining grade control and mine resource estimation. Kriging is also a necessary step in the most commonly used methods of conditional simulation used in the mining industry. In both kriging and conditional simulation, the search volume or ækriging neighbourhoodÆ is defined by the user. The definition of this search can have a very significant impact on the outcome of the kriging estimate or the quality of the conditioning of a simulation. In particular, a neighbourhood that is too restrictive can result in serious conditional biases. The methodology for quantitatively assessing the suitability of a kriging neighbourhood involves some simple tests (which we call æQuantified Kriging Neighbourhood AnalysisÆ or QKNA) that are well established in the geostatistical literature. The authors argue that QKNA is a mandatory step in setting up any kriging estimate, including one used for conditioning a simulation. Kriging is commonly described as a æminimum variance estimatorÆ but this is only true when the neighbourhood is properly defined. Arbitrary decisions about searches are highly risky, because the kriging weights are directly related to the variogram model, data geometry and block/sample support involved in the kriging. The criteria to look at when evaluating a particular kriging neighbourhood are the following: the slope of the regression of the ætrueÆ block grade on the æestimatedÆ block grade; the weight of the mean for a simple kriging; the distribution of kriging weights themselves (including the proportion of negative weights); and the kriging variance. Outside of the technical geostatistical literature, there is little in the published domain to describe the nature of QKNA and no practical presentation of case examples. In this paper we attempt to redress this by setting out the calculations required for QKNA and defining some approaches to interpreting the results. Several practical worked mining case examples are also given. Finally some comments are made on using the results of QKNA to assist with block size selection, choice of discretisation and mineral resource classification decisions.

Jan 1, 2003

By Bailey S, Avraamides J, Jayasekera S

The anodic dissolution of iron from three different Western Australian reduced ilmenites was investigated using the carbon paste electrode technique. A characteristic current-potential diagram, called a cyclic voltammogram (CV), was obtained for each of the reduced ilmenites. The shape of the CV measured for all three reduced ilmenites was strongly time dependent. The effect of electrolyte composition and temperature on the CV of one reduced ilmenite was also investigated. The results suggest that the initial surface of iron in reduced ilmenite is slow to dissolve and that chloride ions and higher temperatures accelerate the dissolution of this initial surface layer. However, after removal of this layer, the dissolution rate was essentially independent of the electrolyte composition and the temperature.

Jan 1, 1996

By Y K. Leong

Iron ore tailings typically containing 40 to 50 per cent Fe can be beneficiated to iron ore products containing 54 to 60 per cent Fe. The impurities are comprised of clay, quartz, cristabolite and TiO2. Goethite and hematite are also present. At high concentrations of 55–60 wt% solids, the tailings displayed high yield stress and viscosity and cannot be pumped over long distances. Composite additives comprising of NaOH, phosphate-based additives and sodium metasilicate are found to reduce the viscosity and yield stress very significantly by a few orders of magnitude. The yield stress of 100 Pa can be reduced to almost zero. At this state, dilution of the tailings with its process water to 40 per cent solids causes the coarse and high-density iron ore particles to separate from the colloidal fractions located in the supernatant after a few minutes of sedimentation. Separation by decantation produces a sediment with an Fe content of 54 per cent from tailings with 47 per cent Fe. Another tailings sample with 48 per cent Fe was beneficiated to greater than 57 per cent Fe using NaOH-metasilicate-polyphosphate additives and employing an additional washing step. The use of other composite additives, NaOH and polyphosphates, increased beneficiated product Fe content to greater than 60 per cent from the same tailings. With the current iron ore spot price of more than US$180 per tonne, the cost of this treatment process even including a desalination step, if necessary, is relatively insignificant. This study has given tailings an economic value that should be exploited as soon as possible.

Nov 8, 2021

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to be considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall materials.

Jan 1, 1998

The sole reason for a mine to exist is to extract the finite mineral resource. Accurate grade control is critical to the economics of any mine. If grade control is not optimised, then no matter how good the downstream processes are, the full potential of the operation will not be realised. The detailed implementation of grade control varies but typically consists of sampling and assaying to determine the location of the ore zones. A lot of time, money and effort are spent defining the location of the ore as accurately as possible à but then it is blown up! The effect that blasting has on grade control is rarely adequately accounted for when the rock is excavated because there has never been an accurate and practical method for measuring blast movement. This paper draws on over six years of research into measuring and understanding blast movement, which started at the Julius Kruttschnitt Mineral Research Centre (JKMRC) of the University of Queensland. The research has made a unique contribution to open pit blasting by helping to develop a practical tool for measuring blast movement, which was then used to improve the understanding of three-dimensional blast movement dynamics. However, these achievements would be of largely academic interest without taking the final step of using this technology and knowledge to account for blast movement by translating the ore polygons in response to the measured movement vectors. This paper provides an overview of blast movement but focuses on one site where blast movement was measured during three separate periods, with significantly different orientation of the mineralisation on each occasion. The theoretical ore loss varied from nine per cent to 24 per cent. The differences are primarily due to the orientation of the ore polygons relative to the direction of movement. The optimum grade control solution is a combination of accurately accounting for blast movement and designing appropriate blasts.

Jan 1, 2009

Viking Holdings Ltd, a Todd Corporation company, is active in the mineral industry through operations, joint ventures and equity investments. Identification and management of risk is key to the success of the company. This paper discusses risk in general terms and in the context of Vikings activities. Reference is made to the current environment and the impact of risk and environment on profitability.

Jan 1, 1997