Search Documents

By Just G. D

The results of a geostatistical analysis of geochemical data obtained from field measurements are described in the paper. Q values derived from seismic signal rise times for different travel paths in the rock masses were used in the study. Cross-hole seismic measurements made at surface and underground sites formed the basis for the work. Geostatistical estimation of average l/Q values for area of the rock were compared with geological interpretions of rock type distributions. Reasonable correlations were obtained between the two methods of rock quality estimation.

Jan 1, 1988

By G Ferguson a, P Carrasco, P P. A Dowd

International codes of practice offer broad definitions with respect to the classification of resources in terms of risk. Specific guidelines and protocols, to analyse sample data, carry out geostatistical appraisals, develop geological models and finally estimate and classify resources, are not addressed. Neither are detailed requirements for engineering mineable reserves from estimated resources. In addition, international codes of practice fail to distinguish between types of deposit, other than in broad terms, as for example, The AusIMM JORC Code (JORC, 1999) which makes reference to diamond and coal deposits. The objective of this paper is therefore to set in motion the process of specifying detailed protocols, acceptable to the international community, for the assessment, reduction and management of risk associated with the development and extraction of mineral deposits. Ordinarily, the main risks and issues encountered during the process of estimating resources and subsequent conversion to reserves, encompass:failure to understand relevant geological controls of mineralisation; validation of grade interpolation; optimism in geotechnical appraisals of dilution and stability and the consequent selection of inappropriate mining methods; metallurgical modelling of minerals and contaminants reporting to concentrates; appraising the hydraulics of heap leaching and the numerous factors that can affect recovery; difficulty of managing metal price cycles and changes in regulations within the constraints of long-term mining plans; and development of better evaluation techniques for mining ventures. Uncertainty is inherent in estimation and engineering work, and its identification, reduction and management should be a fundamental goal of all involved in the mining industry (Figure 1). Variability may be reduced by:following internationally accepted practices for the collection, manipulation and analysis of geoscientific data; and verifying that the procedures actually performed meet the associated standards. Increasing amounts of data will also reduce uncertainty, but only if the procedures used to collect and appraise such data follow the relevant procedures. It is thus the aim of a series of papers in preparation, Beniscelli et al (in prep), to put forward detailed guidelines, for:project sponsors û to provide a global view of the work and documentation needed to support requests for funding various phases of project development and budget approvals; geologists û to indicate a checklist of the requirements and standards for the exploration and estimation of resources; and engineers and economic analysists û the protocols for characterising, modelling, engineering and evaluating the extraction of reserves. It is therefore hoped to encourage the development of consistent standards for declaring reserves within the mining industry. Data from projects and operations will be utilised to illustrate the benefits of adopting a rigorous approach to estimating resources and engineering reserves, Beniscelli et al (in prep).

Jan 1, 2000

By Z Zhao

Coal dust is hazardous to underground coal workers and water spray is the most common and economic method for controlling coal dust. Previous studies proved that the addition of surfactants can improve the performance of water spray on coal dust suppression. The evaluation methods for surfactants vary from different studies. The zeta potential test is a common method for evaluating surfactants with ionicity. Generally, the suspension of coal dust with pure water usually showed a negative value of zeta potential. The addition of cationic surfactants can increase the zeta potential to a positive value with a small dosage, while the addition of anionic surfactants can only lower the zeta potential. However, there is a lack of comprehensive study to investigate the relationship between the zeta potential and the suppression performance for coal dust. The aim of this study is to reveal the consistency and discrepancy between the zeta potential and the suppression efficiency of a surfactant. Firstly, the mixture of cationic surfactant solutions and coal dust would be evaluated by the zeta potential test. The wind tunnel tests would then be conducted for the same surfactant solutions to measure and calculate the suppression efficiency. It was found that the addition of surfactant can increase the zeta potential and the suppression efficiency and it reached the greatest efficiency when the zeta potential approached to zero. The equilibrium of zeta potential can benefit the suppression performance of surfactants in the wind tunnel test. The result of this study can achieve a better understanding of the mechanism for coal dust suppression. The selection of surfactants will also be suggested for researchers or industries in terms of coal dust control. It would be more economic if a similar performance could be achieved by less consumption of surfactants.

Oct 12, 2022

In the Illawarra District of New South Wales, Mines were traditionally developed from the seabord. The advantages were close access to the working faces and a minimal depth of cover. Travelling times to the working faces have become prohibitive in many cases due to progressive westward development of the mines. As a result, additional vent- ilation shafts were sunk to service existing mines and new mines were established west of the Illawarra escarpment. Mining operations west of the escarpment are now being conducted at an increasing depth of cover and can be effected by gas related problems such as high seam gas emission rates and gas outbursts.

Jan 1, 1983

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987

Market forces, particularly iron ore prices, demand that plant operators achieve higher throughput in the worldÆs iron ore beneficiation plants without compromising yields or efficiency. This means that production cost per ton is of paramount importance and that all major pieces of Processing Equipment have come under close scrutiny to improve throughput at their most efficient performance levels and for the longest possible continuous running time. Without doubt the use of modern engineering standards and materials of construction has contributed to matching these throughput, efficiency and availability demands. However, often not enough attention is paid to the so called æinsignificant elementsÆ connecting this metallurgical equipment, such as chutes, pipes or other conveying systems, and particularly to the sufficient protection of their wearing surfaces. The result can be an unplanned and expensive outage caused by the wear related failure of such components. This paper will discuss:the theory of wear and the multiple factors of material and design that contribute to a reduction in wear; and the combinations of modern wear resistant materials available to todayÆs engineer and how, by intelligent selection and correct application, plant availability can be optimised. Examples outlining how these principles have been applied in South Africa showing some improvements leading to increased plant availability.

Jan 1, 2002

By W L. Lane, T R. Yanske

The Doe Run Company and its predecessors have been mining for over 130 years utilising the room and pillar mining method. This method has left approximately 20 per cent of the orebody in the remaining pillars. The original design and planning for the mines did not include extensive pillar extraction. This paper summarises the introduction of the pillar extraction and backfill techniques which have been implemented since 1991. These techniques include the use of low cost fill walls up to 20 m in height and the use of slinger trucks for topping off the fill. In conjunction with these accomplishments, much experience and confidence has been gained in the use of numerical modelling as a method of predicting pillar stability as the mining of pillars progresses. These advances have led to pillar extraction becoming a major portion of the overall production and have added to the mine life of Doe RunÆs six operating mines.

Jan 1, 1998

By D Kent, J Kirkpatrick

The mining industry has long wanted a single communication back bone to cover the majority of their requirements underground. The convergence of communication technologies in the office/surface environment has been identified by the mining industry as a means to achieve their long-standing goal. In particular use of Internet Protocol (IP) systems are seen as proving a basis for a mineÆs communication infrastructure. This paper presents the development philosophy and work undertaken by Inco Limited in Canada, as well as the implications of this on suppliers to enable the technology to be mine worthy and readily available.

Jan 1, 2005

By Best R. J, Poulos H. G

The method for design of primary roof support for the large todoidal cavern constructed to house the Sydney Opera House parking station is presented. The cavern was constructed with 5 m of rock cover beneath Sydney's Royal Botanic Gardens. Design of rock reinfonnent using a combination of fully grouted rock dowels and Macalloy bars was based on control of horizontal shear movement along bedding features in the roof. A combination of linear arch type analyses and non-linear jointed finite element analyses were used in the design study together with an analysis of the shear resistance offered by fully grouted bolts under shear deformation.

Jan 1, 1993

By Vidalinc, Raffoux

Longwall faces producing in the order of 20,000 tons per day of raw coal are presently running in the Houilleres du Bassin de Lorraine of Charbonnages de France. Production levels of twice that level pose some technical and economic problems of coal cutting, ventilation, coal and equipment transportation in the.face and from the face to the sur- face. The peak productions of the equipment in use today, the results of trials with new equipment, the utili- sation of forecasting models (some in the form of software), allow us to fo- resee feasable technical solutions to these problems. They will first be considered in the best possible context (thick- ness, dip, non gassy, soft coal, good strata, no faults). This will give. the necessary conditions to reach daily output'of that level. A sensitivity analysis of these- figures to the effective natural con- ditions will then be undertaken and the implication of such a project on health and safety (dust, climate ...) will be carefully considered. A concise technical and econo- mical approach will permit us to fore- cast the economical interferences of such production units and specially the consequences of sudden variations of the output (downtimes, failures, etc). From this investigation, goals for technological development and re- search areas will be outlined to be able to reach this production target in the XXIst century.

Jan 1, 1988

By T Napier-Munn, D J. Bradshaw, M Chauhan, L Keeney

An important aspect of geometallurgy is quantifying mineral processing attributes, which leads to improved orebody understanding. One of these attributes is flotation performance. Several methods have been developed as indicators for flotation performance, including batch testing leading to kinetic information and the standard grade-recovery curve. This paper makes a preliminary statistical comparison between a newly proposed geometallurgical batch flotation procedure and the æstandardÆ batch flotation test commonly used to measure flotation performance in the laboratory. The new test uses much less material than the standard test, and is much faster. It is concluded that the new method follows the final recovery of the standard method well, suggesting that it will be effective in reflecting ore variability for geometallurgical purposes. Comparison of the methods based on the full grade-recovery curve shows less agreement, but this may be due to the fact that the curve is sensitive to the particular experimental set-up and conditions, which make such comparisons quantitatively challenging. Further development work is therefore planned.CITATION:Chauhan, M, Napier-Munn, T, Keeney, L and Bradshaw, D J, 2013. Progress in developing a geometallurgy flotation indicator, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 201-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

In early-1989, subsidence due to voids at the top of previously filled stopes and stopes awaiting filling,began to threaten the 15 level fill conveyor horizon. This together with the need to maintain production targets meant that a method was required to significantly increase fill placement.Alternative methods of placing dry fill underground were investigated. One option was to drill 200 mm boreholes from surface directly into stopes 600 - 800 metres underground. A drilling program was successfully undertaken, and resulted in the placement of more than 800 000 tonnes of dry aggregate fill via four boreholes.This paper details the drilling program undertaken and discusses the difficulties encountered, the fill placement system and the project costs.

Jan 1, 1992

By J Rapkoch, M Cerna

As long as the tendency of Chilean copper ores continues to feature high levels of impurities, the smelters will tend to produce high-impurity mattes. The most notable impurities include As, Sb, Pb and Zn. Producing high-quality copper with such materials is a major challenge to metallurgical engineers and operators. More investigations into process optimisations and/or alternatives are needed, using both theoretical knowledge and operational skill. Converting of matte in Chile depends on the matte grade using established technologies. Mattes up to 66 per cent Cu, such as those from Outokumpu Flash furnaces, are converted in two stages, while typical Teniente Converter mattes, ranging from 70 - 74 per cent Cu are converted in one blow, directly to copper. In this paper thermodynamic data are used to evaluate possible variations in the use of traditional technologies applied to smelt copper concentrates with high impurity levels. The results of this analysis help to predict the impurity distributions between matte-slag-gas during the slag blow, and between copper-slag-gas during the copper blow. For converting high-impurity white metal, the effectiveness of volatilisation in the slag blow is analysed. In the copper blow, the type and the amount of flux (SiO2, CaO and others) are altered with the aim of optimising impurity distribution to the slag and gas.

Jan 1, 2005

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

The foundation of our industrial welfare lies in the success of our primary industries, and, so far as mining is concerned, it is hoped that for many years it will be a most important primary industry in Western Australia.

Jan 1, 1927

By I J. Holland

Located in North West Queensland, XstrataÆs Mount Isa Copper Operations (MICO) is one of the largest underground mines in Australia with annual production exceeding six million tonnes of ore with average copper grades of three per cent. As at 30 June 2006, the Ore Reserve inventory totalled 87 Mt, with annual diamond drilling planned at >40 000 m in order to convert existing resources and test and define exploration targets. The role of the geology department within MICO is to collect, interpret and communicate relevant geological information to ensure the optimal extraction of ore. Routine underground inspections across multiple ore sources are undertaken and the information derived is then distributed to a range of professionals, operational personnel and management. The information is a æreal-timeÆ geological view for the stakeholders. Ongoing data collection and interpretation has developed a strong geological input to all mine planning processes within MICO. This has created strong synergies between mine planning professionals and a throughput benefit has been seen all the way to the concentrator. The MICO geological framework also provides avenues for a geological focus away from short-term production requirements, and as a result significant orebody scale observations and patterns have been realised that have led to an increase in the accuracy of geological and resource models. This has provided practical benefits for short-term scheduling and production, whilst enabling the realisation of long-term benefits that have a strong potential to increase the volume and value of the MICO resource. This paper will discuss the various mine geology contributions at MICO and illustrate some examples where mine geological input from graduate level has added significant value to the MICO business.

Jan 1, 2007

By Lee M. F, Guilfoyle K

A large hard rock rib pillar was recently preconditioned at Mt Charlotte mine using a novel blasting technique. The motivation for trialling this procedure was a history of past pillar failures, with associated seismicity. Design studies had shown that a new proposed pillar would be at risk of violent failure, and preconditioning was used in an attempt to reduce this risk. Preconditioning by blasting involves physically modifying a selected zone of ground in advance of mining, then forming the pillar so that it incorporates that zone of ground. The modified rock in the zone is intended to allow extra closure (yield) of the pillar in response to mining-induced stress changes. The ground modification was done by tight firing a blasthole array to fracture the rock. The blast design comprised pairs of pre-split blastholes to create a series of short cracks across the target zone, followed by main blastholes to fracture the rockmass between each pair of cracks. A monitoring program was used to establish whether or not the preconditioning was effective. It included conventional extensometers, stress change cells and closure stations, plus a seismic monitoring system. To-date, stoping is complete on one side of the pillar and has just commenced on the other. Results show significant movements within the preconditioned zone and on geological structures in the pillar, as well as lower stress in the pillar compared to an adjacent non-preconditioned site. The preconditioning technique can be applied elsewhere, provided its purpose, mechanism and side effects are understood. Benefits are likely to include more assured production, and successful pillar recovery even in high stress situations.

Jan 1, 1995

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008

By S W. Kingman, D Whit, I S. Lowndes

The use of compressive crushing equipment such as gyratory crushers within minerals processing plants can potentially generate large quantities of dust. Remedies to this problem include the retrofitting of shrouds, enclosures, local exhaust ventilation (LEV) systems and water suppression systems. The single or combined application of these systems must be optimised to ensure they operate efficiently. It is desirable that the future design planning of such facilities include integrated dust suppression and/or removal systems to ensure material delivery rates are maintained and the welfare of the workforce is protected. The characteristic release of dust and the disturbance to the surrounding ventilation airflow is investigated by the construction and solution of computational fluid dynamic (CFD) models validated by data obtained from scale experiments. A 3D computational model was constructed using the FluentTM CFD software to represent the background ventilation regime within an underground crushing installation. The falling ore is represented as a continuum granular fluid falling under gravity from the raised bed of the dump truck. Transient path lines are computed to simulate the updraft airflow generated by the tipping process and indicate the dispersion path of any entrained dust. The relationships between the falling ore material, the displaced air and the shear induced flow are determined by an analysis of the computed volume/mass flow rates predicted across the crusher opening. An analysis of the airflow patterns predicted by the CFD simulation models indicates strong shear flows induced between the tipped material and the surrounding airflow in the vicinity of the crusher during tipping, and a strong influence of the background ventilation regime on the path taken by this shear flow. Scale experimental studies were conducted to characterise the induced shear flow and visualise the potential entrainment and transport of dust. An analysis of these experiments is presented.

Jan 1, 2005

By Player R. L

Measurements of the rate of PbO reduction from high lead metallurgical slags were made under laboratory conditions using graphite, a CO-50%CO2 gas mixture and metallic iron as reductants. The results show a transition in rate-controlling step at low PbO contents (i.e. 6 wt.% PbO). At medium to high PbO contents in the slag, the reduction rate was found to be strongly affected by the slag chemistry, temperature and reductant type. The effect of stirring and hence mass transfer in the slag phase on the reduction rate of PbO was found to be insignificant at medium-high PbO contents. Attention is drawn to the importance of chemically controlled reaction rates at the slag-gas interface. Parallels between these results and test work on a 5 tph scale have been briefly drawn.

Jan 1, 1989