Search Documents

By A M. Mueller

St Helena tunnel is the centrepiece of the Pacific Highway upgrade from Tintenbar to Ewingsdale, abbreviated and commonly known as T2E. At the deepest point the twin tunnels run 45 m below the ridge line of St Helena Hill, located about 5 km west of Byron Bay. The tunnel breakthrough was achieved early in 2014 and the works for permanent lining will be completed in early 2015.Once the project will be handed over to the public in 2015, T2E will deliver a safer highway and uninterrupted traffic flow between New South Wales and Queensland. The design speed in the project area has been set to 110 km/h by the client Roads and Maritime Services (RMS), which will reduce the travel times between Brisbane and Ballina to just over two hours.The two tubes of the tunnel have been designed to accommodate three lanes in each direction with shoulders and walkways on either side of the carriageway. These requirements result in a huge cross-section of about 20 m width and an excavated area of about 210 m2.With the tunnel alignment being situated in basaltic rock, St Helena tunnel is conventionally driven. The selected excavation method was predominantly drill-and-blast with temporary support being installed immediately after the excavation. Despite the wide span of the tunnel, the geology allowed the tunnel perimeter to be supported by only rock bolts and a layer of shotcrete over the majority of its length.Due to environmental reasons one of the approval criteria of the project was that the tunnel must not have a detrimental long-term impact on the groundwater system within St Helena Hill. Consequently the tunnel has been designed as a fully tanked structure with a waterproofing sheet membrane installed on the temporary shotcrete.The permanent structure of the tunnel has to meet a 100-year design life and it is designed as a cast in situ concrete lining. Considering the water pressure on the lining the concrete is reinforced with a significant amount of bar reinforcement.The presented paper provides a more detailed explanation of the geology and the consequential temporary and permanent support measures together with the waterproofing system.CITATION:Mueller, A M, 2014. Pacific Highway upgrade from Tintenbar to Ewingsdale (T2E), St Helena Tunnel, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 419–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By H R. Watli, K L. Davies, J A. Johnson

Novel microbial isolates that readily oxidise iron and sulfur were recovered from samples collected from a spent chalcopyrite/pyrite test heap. Methods were developed to enrich and isolate microbes that thrive in low pH environments and utilise iron and/or sulfur as sources of energy. Screening of these isolates revealed diverse substrate utilization (sulfur, ferrous ion, chalcopyrite, pyrite, glucose) as well as growth at temperatures between 30 - 50¦C. When native isolates were employed, shake flask leaching tests of chalcopyrite concentrate resulted in higher copper yields in comparison to laboratory reference strains Acidithiobacillus ferrooxidans (DSM 583) and Sulfobacillus thermosulfidooxidans (DSM 9293). After 700 hours several native isolates had leached between 20 - 30 per cent more copper than laboratory reference strains during experiments conducted at 45¦C. This research has established a unique culture collection of mining microbes that readily adapt to Australian conditions. Exploitation of these microbes may result in improved leaching kinetics and copper recovery from Australian chalcopyrite ores as demonstrated from shake flask leaching tests. Whilst this research provides a capability for Australian mineral sulfide ores, this technology can be easily adapted to suit ores of any origin resulting in more effective and efficient microbial leaching.

Jan 1, 2004

By M S. N Hadi, J Hossein

Numerical modelling is extensively used in civil and mining engineering applications because of cost and risk problems associated with different experimental studies. In this study, the effect of resin thickness was evaluated in bolt-grout-concrete interaction and bending behaviour of a fully grouted bolt installed across joints in post failure region. Tests were conducted in 20 and 40 MPa concretes, and modelling simulations were made, using ANSYS version 8.1, to include both with and without different pretension loads. It was found that in all resin thickness, both the strength of the concrete and bolt pretension had major influences on the shear resistance and shear displacement of the reinforced medium. Also it was found that the strength of the surrounding concrete is more important than that of the grout thickness in both the shear resistance and shear displacement when the bolt is pretensioned.

Jan 1, 2005

By Ellyett C. D

This paper is an appraisal of the application of optical-mechanical-scanners operating in the non-photographic infrared wavelengths (3-5 and 8-14 micrometres) to mineral exploration in Australia. Pundamental principles of the operation of airborne scanners and their data output, thermal infrared (IR) imagery, are summarized. It is contended that thermal IR imagery often depicts the distribution of electromagnetic radiation emitted from earth surface materials better than aerial photographic techniques because optical-mechanical-scanners sample wavebands which straddle the wavelength peak of earth surface emission. To illustrate the geological features which such scanners can depict, reference is made to thermal IR imagery of a number of areas in Australia where the technique has been applied for exploration purposes. The images demonstrate that this technique can detect structural features like faults and folds, stratigraphic data by distinguishing different rock types and delineating their

Jan 1, 1973

An international raw material partnership, a $164 million 900,000 long ton per year aluxAna plant; an ideal location at Gladstone, Queensland, Australia - this is Queensland Alumina Limited, on stream in 1967 expanded 50 per cent by the end of 1968. Queensland Alumina Limited is the world¦s most modern alumina refining operation which is owned by an international consortium of four companies; Kaiser Aluminum & Chemical Corporation of the United States with 52 per cent; Alcan Aluminium of Canada with 20 per cent; Pechiney of France with 20 per cent; Conzinc Rio Tinto of Australia, 8 per cent. Q.A.L. operates as a co-operative -- the partners do not draw profits from the venture. Instead, each member of the consortium draws alumina in proportion to his share of the ownership. The method of disposal of this alumina is for the partner to decide.

Jan 1, 1969

By Ueki S

Underground coal gasification (UCG) is a promising process for obtai- ning energy from coal, which is either unmineable with current mining techno- logy or uneconomic to recover, using conventional methods, in the present energy market situation. There are several coal fields, which could become new coal reserves, if the UCG process were successfully applied. In the 1960's Japanese researchers made a number of basic studies and field tests into UCG, although not all of them produced favourable results. This paper reviews Japanese research on UCG. This includs basic studies into coal gasification using a small, tube reactor fed by air and oxygen, and also large scale model stu- dies(reactor size of 8.Om x 2.4m x 1.5 m). Field test results from Akabira colliery in Hokkaido and a feasibility study of power generation using UCG from a coal field in Hokkaido are also Presented.

Jan 1, 1987

By Mowat BA, Leach TM

The Morobe Goldfield in Papua New Guinea has produced in excess of 120 tonnes of gold from predominantly alluvial sources. Hardrock gold has been mined historically at Wau (23t) and Edie Creek (40 and geological resources have been established at Hidden Valley (780, Kerimenge (360 and Hamata (30t). Numerous prospects have also been identified within the goldfield. Primary gold mineralisation is related to intrusion of dacitic to andesitic Edie Porphyry (2.4 to 3.8 Ma), often with associated diatremes, which have intruded along major regional structures. A full spectrum of deposit styles from proximal (mesothermal) to distal (epithermal) to the porphyry source is recognised. The transition between the proximal and distal styles is recognised both between deposits and within an individual deposit. The deposit styles should be termed porphyry related gold mineralisation rather than given the generic epithermal and mesothermal labels.

Jan 1, 1995

By M E. Malmstr÷m

Quantification of site-specific sulfide oxidation rates is crucial to accuracy of prediction of, for example, the environmental impact of a mine site. Sulfide oxidation reactions are reportedly increased by bacterial mediation; determination of abiotic and biotic weathering rates thus requires the establishment of sterile control samples. However, sterilisation often involves exposure of samples to extreme conditions that may alter the physical, chemical, or mineralogical characteristics of the tailings and hence affect element release rates. The impact of various sterilisation techniques, common and novel, on the element release rates from tailings from the Kristineberg site, northern Sweden, has been investigated. Batch weathering experiments indicated that the different methods of sterilisation (autoclaving, heat treatment, ethanol/heat treatment, application of antibiotics, rinsing with distilled water, and γ-radiation) did not greatly affect long-term element release rates. Long-term experiments (>30 days) are thus to be recommended for establishment of weathering rates. Sterilised and untreated control samples showed similar element release rates after ~100 days of experiments; possible explanations include that microbial oxidation is not important under our experimental conditions (Po2 = 0.2 atm, pH ~2.3, 22¦C, 0.01 M HNO3, no additional nutrients).

Jan 1, 2003

By T Mizuta, D Ishiyama

The Vienna Wood hydrothermal is hosted by mid-oceanic ridge type basalt in graben morphology and is located in the Central Manus Basin. The hydrothermal field is about 300 metres in diameter and consist of a sulphide mounds and tall huge death and active chimneys. From the three distinct ore types collected from the Vienna Wood site, the dominant ore minerals recognised are pyrite, wurtzite, sphalerite, chalcopyrite, Fe-oxide and gangue minerals of anhydrite, gypsum, barite and silica. The consistencies in the paragenetic sequence and in the spatial distribution of the sulfides across the three ore types suggest that similar hydrothermal process exist across active and death chimneys. Fluid inclusion studies reveal a homogenisation temperature of 190-260¦C and an average salinity of 5.1-5.4 wt per cent NaCl equiv. The pH of the hydrothermal fluid ranges from 4.2 to 6.1. Bulk chemical analyses indicate that the mineralisation in the Vienna Wood can be classified into the Zn-(Cu-Pb) type of mineralisation. The tenors of the ore and mineral assemblage resemble those of the Mid-oceanic ridge system and ancient ophiolite hosted massive sulphide deposits of Cyprus and Oman.

Jan 1, 2002

In todayÆs evolving and globalised world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to æengageÆ communities and measure the success of these engagements without a clear understanding of æhowÆ to do this. This move, away from compliance, develops more of a focus on sustainability and æcommunityÆ social responsibility rather than corporate social responsibility. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of æengagingÆ communities in mining project design and development leads to sustainable development, a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be æengagedÆ in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this æengagementÆ and manage this risk will be discussed.

Jan 1, 2007

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

By Y D. Jeon, K S. Kim, C-H Eom, C M. Yoon

The carbon neutrality continues to require reduction of carbon usage in ironmaking and steelmaking processes. Specially, it is expected that the hot metal ratio (HMR) in the steelmaking process should be reduced essentially. Unfortunately, the reduction of the HMR in converter can bring about poor environment for nitrogen removal from molten Fe. From this situation, nitrogen prediction model has been developed to understand the fundamental of behaviour of nitrogen and quantitatively interpret its content changes in the converter process. Thermodynamic and kinetic approaches were improved based on existing mathematical model and attempted to predict nitrogen content in realtime by combining process data. In present study, heat supply from the oxidation (mainly carbon and silicon) and CO evolution in the converter are considered, and scrap melting due to the heat transfer from the molten Fe to the solid scrap charged in the converter also be considered.

Aug 21, 2024

RME has a vision for a new grinding plant operational paradigm made possible by RMEÆs fast, safe Mill Relining System. Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by modifying liner design for maximum life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. Following the introduction, the first section of this paper provides an update describing recent and significant developments within RMEÆs range of Mill Relining Systems, the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The second section outlines RMEÆs vision of a æliner profile versus profitabilityÆ commercial model, developed either intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2007

By Dunstan N, Valentine C

Gas power was first used on the Sons of Gwalia mine in January 1911, when a twin-cylinder Crossley engine of 167 hp was installed to belt-drive a 112 kw 550-volt ac generator. This engine was connected with a No 8 Crossley up-draught suction gas producer, using mulga charcoal as fuel.A second Crossley engine, of 400 hp direct-coupled to a 550-volt ac generator, was installed in 1912, and operated by a down-draught wood producer.This was followed by a large Kynoch twin tandem four-cylinder engine, rated at 660 hp, sea level, with a rope drive to the crushing and treatment sections of the plant.These engines operated until January 1921, when the plant and power house were destroyed by fire. After the fire, both Kynoch and second Crossley engines were salvaged and reconditioned and they continued to give useful service for some years.

Jan 1, 1932

Record quantities of slag were produced in 1974. Slag usage in this year amounted to 8.5 mega tonnes for granulated blast furnace slag and 7.7 mega tonnes for crushed blast furnace and L.D. slags. Granulated blast furnace slag is mainly used as a hydraulic bonding material in the manufacture of cement and in road construction. These applications give a fuel saving and reduce processing costs. Crushed blast furnace and L.D. slags find application as a substitute for natural aggregates in road construction and in the production of concrete. There is no doubt of ttie interest to utilise to the maximum all the slag produced by the steelmaking industry, thus preventing the build up of slag heaps detrimental to the environment and favouring the disposal of the heaps formed in the past. World wide efforts are being made to achieve this objective.

Jan 1, 1979

By A R. A Gomes

The Metropolitan Rapid Transit Authority (MRTA) Initial System Project (ISP) - Underground Structures North, UGN, is the northern section of the blue line, which is the first stage of an underground mass transport rail system of 77 km to be implemented in the central area of Bangkok, Thailand. The UGN section (Huai Kwang - Bang Sue) consists of approximately 8 km of twin single track bored tunnels, nine underground stations and some short cut and cover tunnel sections. The paper focuses on the main issues involved in the structural design of the precast concrete lining, which is the definitive structural support of the bored tunnels. It includes an overview of the site and geotechnical conditions, specific properties of precast concrete linings, ground-structure modelling, approach for the assessment of load conditions and respective sectional forces and particulars of the detailing of the reinforcement and the segment testing program.

Jan 1, 1999

By M Bellamy

The DeGrussa copper deposit was discovered by Sandfire Resources in April 2009. Construction of the 1.6 Mt/a concentrator, open pit and underground mining operations commenced in March 2011 with first concentrate production achieved in October 2012. Over the next ten years, DeGrussa grew to include both the DeGrussa and Monty underground mines, establishing itself as one of the world’s premier copper producers with total production of 663 000 t of contained copper by the time the mine closed. Final ore was trucked from Degrussa on 5 October 2022. This paper examines the mine closure experience from both a planning and operational perspective. The paper provides an overview of the site’s mine planning process including the factors involved in determining the end of the mine life and how this was tracked and communicated in the lead up to the end of mining operations. It will also look at some of the specific operational aspects involved in maintaining steady state production all the way through to the last day while facing increasingly challenging conditions. These factors, along with the external factors faced by most of the industry such as labour shortages and COVID related disruptions, contributed to making it an interesting journey to the end of operations at DeGrussa.

Mar 29, 2023

By M Frenzel

At the last MassMin Conference in Sudbury, Caterpillar’s vision of a continuous mining concept for block caving operations was presented on the background of global raw material demand and its continuous increase. By analysing today’s structure of mining processes in block caving, the paper (Krings, Steinberg and Frenzel, 2012) highlighted the main bottlenecks in the process chain and identified conceptual solutions by help of a case study. The main focus was the paradigm shift from discontinuous batch type operation to a continuous mining process of the blocks.In 2016, the strategic vision has taken major strides forwards and remote continuous operation has become a reality. Caterpillar’s continuous operation system – the Rock Flow system – was successfully installed in Codelco’s Andina mine and start of operation is scheduled in the first half of 2016.Based on continuous product developments, this paper sets the focus on two main aspects of continuous mining. First, field experiences of the Rock Flow system will be shared, highlighting the Andina project course from system installation, to commissioning and successful system start. The second aspect concentrates on the system and mine layout as discussed in the case study scenario in MassMin 2012 (Krings, Steinberg and Frenzel, 2012).Based on Caterpillar`s continuous product development, the Rock Flow system set-up and panel design were modified for a general roadway design and drawpoint layout. The new design allows an optimised use in block preparation phase (spreading) and full production phase (reaping), operating a fleet of load-haul-dumps (LHDs) and Rock Flow systems. The combined use of the two technologies optimises the mining process in every stage of block life and significantly increases the performance of the continuous block caving operation in the production panel to pave the road for the next generation of super caves.CITATION:Frenzel, M, 2016. New continuous production system in block cave mining – the rock flow system, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 543–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

By T Ireland, B Wright, S Weaver

All tunnels have unique characteristics that result in different fire and life safety risk. The fire safety systems for each tunnel also give different benefits at different costs. It is therefore neither pragmatic nor cost-effective to prescribe specific fire standards requirements for all tunnels. Each tunnel needs to be assessed individually but using a common process.The owner/client is normally the risk owner and needs to make the decision on what fire and life safety provisions will be provided within the tunnel. To make this decision they need to be appropriately informed. The low probability and high consequence nature of fire events creates a challenge such that traditional analysis processes, which tend to focus on a major event after it has happened, are not easily applied and do not give the best value for money. Therefore a process is required that provides the relevant information to the owner for decision-making.A quantitative risk assessment (QRA) provides a process and framework for the consideration of fire life safety risk when applied properly. This involves a risk assessment of the ‘do nothing’ option together with assessments of improvement options and their costs. It also involves consideration of benchmark safety levels for other tunnels and the open road.This paper will outline a QRA process for assessing fire and life safety risk in tunnels and how this has been used for three existing tunnels, Homer Tunnel, Lyttelton Tunnel and Mt Victoria Tunnel. Key challenges include determining an acceptable safety level, defining realistic inputs, providing sufficient complexity to get meaningful results but not so complex that transparency is lost and interpretation to enable decision-making by non-technical personnel.CITATION:Weaver, S, Wright, B and Ireland, T, 2014. A transparent and pragmatic quantitative risk assessment process for assessing fire safety in New Zealand tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 121–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014