Search Documents

By G Harbort, V Lawson

Mount Isa Mines Limited operates one of the worldÆs largest underground mines in North West Queensland. ItÆs mining and smelting complex produces copper anode, crude lead bullion (containing silver), and zinc concentrate. Copper is recovered in the Copper Concentrator from chalcopyrite ore, converter smelter slag and rotary holding furnace (RHF) slag via grinding and flotation operations. During 2002 a project to optimise cleaner circuit capacity was commenced. Its aims were to minimise copper losses and minimise slag/chalcopyrite cross contamination by reconfiguring existing flotation equipment and the addition of new flotation capacity. To minimise cross contamination a Jameson Cell was installed and dedicated to cleaning of slag concentrates, which had formerly been conducted by three flotation columns operating in series. The flotation columns were re-configured to operate in parallel and dedicated to upgrading chalcopyrite concentrate. In addition a Jameson Cell was installed to reject entrained copper from a prefloat concentrate consisting of talc and carbonaceous pyrite. This paper discusses the logic behind the cleaner circuit expansion, recent test work relating to the Jameson Cell and the installation and commissioning phases. Difficulties relating to the commissioning are reviewed and the solutions to problems are highlighted. The benefits the reconfigured circuit has provided to Mount Isa Mines are also discussed.

Jan 1, 2003

By H Benzer

Grinding clinker to finished cement consumes more energy than any other comminution process. World production of cement in 2009 was 2840 million tonnes and the energy required for comminution was 40-60 kWh/tonne depending on the clinker characteristics and the fineness of the finished cement. Machines used include single and multi compartment ball mills, HPGRs, vertical roller mills, centrifugal air separators, V separators, screens and crushers. The circuit most commonly used consists of a closed circuit HPGR followed by a single compartment ball mill and an air separator, and in operation the variables are adjusted to obtain maximum throughput with no loss of quality of the separator fines.A common objective in cement plants is to reduce energy consumption without affecting the particle size in the finished cement and simulation is used as one procedure to achieve this. Models are now available for all the machines commonly used in clinker circuits and circuit optimisation studies using simulation have been carried out in many plants leading to decrease in energy consumption per tonne of cement. In this paper the models used will be discussed briefly and several case studies will be reviewed which will highlight the effect of change in ball size in a two compartment mill, the role of the HPGR in an HPGR – ball mill – air separator circuit, and the use of a high intensity vibrating mill for producing finished cement with high additive ratio.

Aug 8, 2011

By D J. Hill

"Mining companies routinely invest in improvements to their processing operations, but often these enhancements do not work to full effect.Improvements can be ineffectual because underlying process problems are not identified or prioritised for correction or repair.This is frequently because ‘black box’ solutions deployed to implement process control improvements typically rely on instrumentation to provide data for algorithms to work effectively, and these solutions are often ineffective or disabled at mineral processing sites.There are three key reasons they can fail to deliver: vital instrumentation is not calibrated or functioning as required basic process control and loop tuning was not implemented correctly or is in need of tuning there is an inability to support the ‘black box’ solutions on-site.Many of these problems can be overcome by implementing operational analytics that identify where problems are occurring and prioritise where improvements need to be made.Incorporating operational analytics into process improvement is not a new methodology. It is more a back-to-basics approach to make more efficient use of capital and systems already deployed.Data collection systems, such as the OSIsoft PI System, provide real-time and historical process information for process control experts to analyse and identify areas for improvement. However, most systems are not used effectively. With some simple enabling, data collection systems can provide evidence for prioritising investments in improvements and determining an investment’s effectiveness.MIPAC advocates that the initial step, with analytical evidence, is that clients review the control strategies and implement small influential instrument repairs/calibrations and operator training. This can significantly boost process productivity without the need to spend large sums of money on new capital or employing expensive, difficult to maintain ‘black box’ solutions.A simple Stage-Gate®-style approach ensures that small investments in evidence-based process improvements deliver significant benefits to mining operations.CITATION:Hill, D J, 2014. How to prioritise process improvements, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By J B Tucker, A T. McGrath

Situated in north-west Queensland, Australia, the Ernest Henry Mine (EHM) has been producing copper and gold since 1996. Owned and operated by Glencore Xstrata, ore is currently sourced from a newly developed underground sublevel cave (SLC) mine below the old EHM open pit (the pit). Ore feed to the concentrator is supplemented by satellite open pits comprising the Mount Margaret operation.The transition from open pit to a producing underground mine involved a complex extraction sequence for the first two production sublevels on RL1650 and RL1625. Underground mining during cave initiation was further complicated when south wall instability prevented completion of the final open pit shell. The transition mining phase included mass firing of an inclined crown pillar between the initial SLC void and the pit followed by a combination of transverse and longitudinal SLC mining.The inclined crown pillar mass firing was the first significant milestone in the extraction of the transition ore block. Comprising approximately 890 000 t of in situ material; 70 000 m of drilling was charged with 351 t of emulsion and 6026 electronic detonators to initiate the single mass firing. The firing contained five direction changes over 19 seconds making it one of the largest and most complex underground blasts ever conducted in Australia.Risk management was integrated into every facet of the technical and operational planning and execution of the transition mining phase, whilst maintaining daily mine construction and production commitments. This paper provides a detailed overview of the transition objectives and constraints, mining method selection, post mass blast outcomes and the journey ahead.CITATION:McGrath, A T, Campbell, A D and Tucker, J B, 2014. Transition of the Ernest Henry Mine from open pit to an underground sublevel cave, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 297–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

The Pilbara region, located in the north-west of Western Australia, is significant as the second-largest source of iron ore on the planet. Iron ore mines owned and operated by Pilbara Iron are located within the Hamersley Basin. This paper refers to the Greater Paraburdoo mines, the 4WEST and 4EAST pits, located on the southern margin of the Hamersley Basin. The groundwater model refers to ephemeral watercourses: Seven Mile and Pirraburdoo creeks, which are adjacent to the two pits, and Ratty Springs, located upstream from 4WEST and within Pirraburdoo creek. The spring and creeks hold cultural heritage significance for local Aboriginal communities. Two of these, the Gobawarrah Minduarra Yinhawanga (GMY) and Innawonga native title claim groups, initiated hydrological work on the two creeks and Ratty Springs, with the aim of determining the affects of dewatering on the natural water flows of these systems. The numerical model used to simulate drawdown in the Pirraburdoo and Seven Mile Creeks was derived from PMWIN Pro software and covered an area of 77 km2. The modelling period was from January 1998 to December 2004, and the prediction period was from January 2005 to December 2015. The model has four layers and incorporated effects caused by mining voids, 4WEST and 4EAST pits, creek bed material, weathered bedrock below creeks and surrounding banded iron formations (BIF). The model has been calibrated using the trial-and-error method set down by Middelmis et al (2001). The current dewatering schedule (12 ML/day) in the 4WEST and 4EAST mining areas does not affect the water table levels in the adjacent creeks significantly or for any considerable periods of time. However, changes to mine plans may occur, for example, in response to changed commodity price and may lead to significant increase in rates of vertical advancement. This, in turn, affects dewatering schedules, as greater vertical advancement requires increased dewatering effort. When an accelerated mine plan is applied to the model and dewatering rates increased to 18 ML/day, drawdowns in the creeks are more noticeable. The model has therefore helped to indicate the extent to which increased dewatering rates may be acceptable, especially in terms of immediate and longer-term damage to riparian species, ie Melaleuca and Eucalypt. Predictions from the model may also allow mine planners to schedule decreased rates of vertical advancement, where these are required to meet environmental constraints.

Jan 1, 2006

By A Hutton, C Dick, D Fletcher

Mine and facility closure planning is a dynamic and rapidly evolving landscape. In this landscape, mining companies and industry consultants are generally good at estimating the associated earthworks and rehabilitation costs, because it is æcore businessÆ. Through our extensive work in mine closure, we have found that the safe and cost-effective demolition of mining related infrastructure is often grossly underestimated. Or alternately, it is simply assumed that the returns on scrap steel and the sale of re-usable plant will cover the related costs. With fluctuating steel prices and no guaranteed buyer for the assets, the estimated monetary return is often unreliable and in many cases unrealistic. On this basis this logic is fundamentally flawed. We have found that on most occasions this has meant that closure cost estimates fall well short of what the actual costs are to close the mine.GSSE and Liberty Industrial have worked on over 60 mine closure projects in Australia and overseas of varying scales and across a range of commodity types. An evaluation of these projects has shown that costs associated with the safe demolition and removal of a mining related infrastructure is in the order of 20 - 30 per cent of the total cost at closure. We believe it is one of the top three risk areas associated with mine closure planning and cost estimation, alongside bulk earthworks and the capping of tailings and waste rock storage facilities.Our paper uses examples from recent projects to demonstrate all aspects outlined above. We have also endeavoured to address the following key points related to the demolition and removal of mining related infrastructure:If companies fail to plan appropriately, complicating factors such as contamination, hazardous materials, mobilisation/demobilisation, geographical location, decommissioning standards, site constraints and weather, can add considerable costs to the project and result in variations for the demolition contractor.Closure planning often assumes infrastructure that is no longer required can be utilised by a third party and/or the new land holder. We intend to show that unless adequate consultation and planning is undertaken, this is not beneficial to the mining company, the environment, or the local community.CITATION:Fletcher, D, Hutton, A and Dick, C, 2012. The æsmoking gunÆ of detailed mine closure cost over-run - A review using case studies of the real costs associated with the demolition and removal of infrastructure in mine closure, in Proceedings Life-of-Mine 2012 , pp 325-332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M Darvall And R Fare, D Dormer

The Argo Archaean lode gold deposit is hosted within a structurally complex shear zone system, 70 km south of Kalgoorlie, and 3 km west of the crustal-scale Boulder û Lefroy Fault. Argo is an active underground mine currently producing at a rate of 120 koz pa with a Probable and Proven Reserve as at December 2005 of 2.19 Mt at 5.94 g/t Au (419 koz), a reduction on the December 2004 Probable and Proven Reserve of 4.58 Mt at 5.74 g/t Au (845 koz). This Reserve is hosted in six separate gold bearing lodes within the Argo shear system. Presently, a further six subeconomic shears are recognised. The 2005 Reserve figure represents a reduction of 426 koz compared to the 2004 Reserve as a result of a thorough review of the geological interpretation/resource model, and engineering factors applied to the Resource/Reserve, and depletion due to mining. Year on year Resource/Reserve figures at Argo had gradually increased as additional information on the system became available and mining methods were increasingly resolved with early production. The portal for Argo underground mine was cut in June 2002 within the highly profitable Argo open pit. The proposed æAvocaÆ bottom-up mining method required extensive lead time between development and the commencement of stoping in April 2004. During development considerable additional complexity in the Resource was encountered. Additional structures were identified, and complex splay interactions affecting the geology impacted on development. Intensive concurrent exploration in the footwall to the main lode during this period was the main cause of the increase in the Resource/Reserve figures during early development. As development progressed, lower grade continuity was observed than was previously interpreted. At the same time, drilling of deeper portions of the deposit and subsequent reinterpretation of the geological model significantly reduced strike lengths of economic mineralisation. Radical changes to the mining methods were required to improve productivities and to satisfy geotechnical considerations. The changes altered the engineering factors applied, which resulted in a reduction in the Reserve figures.

Jan 1, 2006

By A J. Gunson

The Norman B Keevil Institute of Mining Engineering, or the Department of Mining Engineering (the Department), at CanadaÆs University of British Columbia (UBC) is addressing the integration of sustainable development concepts into mining education and research on behalf of industry and society. Over the past decade, the DepartmentÆs education and research model has been evolving to incorporate collaborative and multidisciplinary strategies, where sustainability initiatives are taught in classes, supported in research and discussed in a voluntary collective of mostly graduate students û the Sustainability Working Group (SWG). The SWG has brought together a diverse array of disciplines from academia, industry, government, non-governmental organisations (NGOs) and mining communities. The operational mechanisms and structure of the SWG have enabled momentum to be gained through several multidisciplinary educational and research networking initiatives. It acts to attract new students with diverse backgrounds, foster innovative research, develop relationships and networks, and create the space to discuss progressive ideas and projects. The original cohort of SWG graduate students laid the foundation for sustainable research initiatives within the Department at UBC. Novel research has incorporated topics such as: community resilience, artisanal small-scale mining, sustainability indicators and corporate social responsibility, environmental assessment and impact benefit agreements and the recycling of waste. Propelled by the support of the Department and inspired by the works completed, a host of new graduate students have embarked on their research quests to integrate sustainability principles into their projects. Such projects include: social impacts and benefits of mining, artisanal small-scale mining, community health, the production and transport of mine pollutants, mine waste management, mineral process plant design and the evolution of community education and mine policy. This paper reports on the departmentÆs continuing research and development towards an understanding and evaluations of the ongoing contributions of mining to sustainable development.

Jan 1, 2009

By C Linklater, J Chapman, A Watson

Closure options under consideration at some sites include backfilling mined-out pits with waste rock. Backfill may include mineralised and non-mineralised waste rock. Following groundwater rebound, flow-through conditions may develop in the pit post-closure. The backfill located in the saturated zone below the water table may release solutes under such conditions. It is therefore important to understand the potential impacts that backfilled pits could have on postclosure groundwater quality.Geochemical characterisation programs are the foundation for assessing the potential chemistry of water that has contacted mined wastes. Such programs must be designed to obtain data relevant to the closure options under consideration. To complement standard testing techniques, SRK utilises saturated column testing designed to generate data on leaching rates under anoxic conditions that could be encountered within submerged backfill.This paper presents the findings of saturated column test work carried out on waste rock samples from an iron ore mine in the Pilbara.CITATION:Watson, A, Linklater, C and Chapman, J, 2016. Backfilled pits – laboratory-scale tests for assessing impacts on groundwater quality, in Proceedings Life-of-Mine 2016 Conference , pp 110–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By J D. Illescas, S N. Arnold, D R. Shaw

Ion exchange (IX) as a primary production technique has been applied commercially since the 1950s; its application in the uranium industry continues to be widespread and is utilised to a lesser degree in the gold industry. The majority of ion exchange applications, outside of gold and uranium, have primarily been for secondary metal recovery and impurity removal. Newer developments in the application of ion exchange, as well as changes in regulatory requirements, are bringing about the wider use of ion exchange as a primary production technique not only for high value metals such as uranium, platinum group metals (PGM), refractory metals and rare earths, but also looking at base metals such as nickel and copper. The ability to build lower-cost, safer, less polluting processing plants with smaller footprints is driving a greater interest in IX, with the main competitors remaining solvent extraction and carbon-in-pulp/leach. This paper discusses a number of areas where IX has been applied and its advantages compared with other techniques.CITATION:Shaw, D R, Arnold, S N and Illescas, J D, 2012. Ion exchange in hydrometallurgy - Secondary metal removal or primary production technique?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 17-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S Mitra, D O’Dea, N Barrett, T Honeyands, E Copland

This work describes a novel mapping technique that allows the direct overlay of calculated local phase equilibria on micrographs of the physical system. The technique demonstrated integrates FactSage™, ver 8.2 (by Thermfact Ltd. and GTT-Technologies) phase equilibria calculations with mapped compositions determined by Scanning Electron Microscope – Energy Dispersive X-ray Spectroscopy (SEM-EDS) to visually express calculated properties while preserving the spatial information of the sample. The developed methodology is used to analyse interrupted blast furnace softening and melting tests containing mixed burdens of lump and sinter. Tests are interrupted at 1300C and cooled to room temperature for analysis. Phases present at room temperature are analysed to infer the liquid fraction and phases present at high temperature. Analysis of the interface regions between the dissimilar burdens allows insights to be gained into the interaction mechanism. During the transition from solid to liquid, migration and interaction of liquid oxide across the interfaces of the dissimilar burdens has been observed and demonstrated to impact softening and melting performance. Specifically, interaction of the oxides generated by lump (primarily FeO, SiO2 and Al2O3) and sinter (primarily FeO, CaO, SiO2, Al2O3 and MgO) are analysed, and the occurrence of a range of new mineral phases such as merwinite, melilite, olivine and bredigite observed.

Jun 19, 2024

It is a privilege for me to participate in this vitally important discussion of The Role of Governments in the Management of Resources. The distinction of my fellow participants is evidence that this event is a matter of extreme importance and attracts international attention. In the management of natural resources, government and private enterprise share awesome responsibilities for the economic well-being of nations. Mining and its relation to the prosperity of nations is almost as old as recorded history. Copper was being mined and extractive metal- lurgy practised at Timna in Israel's southern desert as far back as 4000 B.C., and the rich mines of Laurium not only saved the Greeks from Persian domination 2500 years ago, but also provided Athens with a monopoly of silver in the Mediterranean world. This bolstered the economic power of Athens and led to the golden age of Greek commerce and culture.

Jan 1, 1978

By R Dimitrakopoulos, K Kawahata, L Montiel

A method that optimises mining complexes that are comprised of multiple processing destinations, open pits and underground operations is presented. Mining, blending, processing and transportation decision variables are simultaneously optimised while accounting for geological uncertainty. The method uses a simulated annealing algorithm at different decision levels to generate a stochastic-based extraction sequence and processing policies. A case study shows its ability to generate a higher net present value while facing a reduced amount of risk when compared to traditional optimisation methods.CITATION:Montiel, L, Dimitrakopoulos, R and Kawahata, K, 2014. Globally optimising open pit and underground mining operations under geological uncertainty, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 201–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By C G. Sweeney

The underground mining industry is seeing unprecedented shortages in skilled labour. Migration to Australia being at an all-time low is a leading concern, with pandemic-induced border closures and lockdowns only exacerbating the skills shortage, not causing it. The skills shortage is forecast to peak in 2023 and remain high beyond 2025. With this skills shortage in mind, mining companies throughout Australia are trying to deal with stricter protocols around Health and Safety (H&S) legislation, as well as more stringent controls on quality assurance, particularly as underground mines are reaching greater depths and extending into ‘unchartered territory’. The cumulation of this is proving to be a major hurdle in ‘effective’ operational geotechnical management. The drive for automation in mining is bringing another level of complexity. However, ‘once automation is up and running, it presents the opportunity to access talent pools that may not normally be available. There is also a change in skillset that will be required to drive automation. ‘The top two emerging roles that will be critical for the future of the mining industry are artificial intelligence and machine learning (AI/ML) specialists, and process-automation specialists’ (Writer, 2021). If anything positive has come from the pandemic, it has shown that remote working can be effective and that the drive for automation and critical evaluation of skills required on-site should be given greater priority. UQ acknowledges that the industry is changing, and that digital technology is required to be offered in mining related disciplines. Industry and academia need to do more to promote geotechnical engineering in mining and balance the curriculum to suit the future of mining and make it more enticing. The average cost of a geotechnical failure is about $5 million in coalmines and can be into the hundreds of millions of dollars if production is affected (Cartledge Mining and Geotechnics, 2020). The cost of a good geotechnical design far outweighs the potential losses if a failure were to occur. This alludes to the growing importance of experienced geotechnical consultancies playing a pivotal role in managing mine site geotechnical hazards, while the industry is developing the next generation of geotechnical engineers.

Nov 29, 2022

By S Dorrington, J Olsen, N Kinkaid

Several studies have been conducted on the economic analysis of mining near-Earth asteroids for resources for use in Earth orbit. While these studies use detailed economic figures of merit, they often use many invalid assumptions in the trajectory design. Factors such as the energy and propellant requirements are estimated with analytic methods, however, the stay-time at the asteroid and the spacing of repeated launch opportunities are not taken into account. The work outlined in this paper attempts to combine detailed trajectory design methods with newly defined economic figures of merit to improve the economic assessment of asteroid mining missions. The study focuses on asteroid 2014 EK24, a near-Earth asteroid with very Earth-similar orbital properties.CITATION:Dorrington, S, Kinkaid, N and Olsen, J, 2015. Trajectory design and economic analysis of asteroid mining missions to asteroid 2014 EK24, in Proceedings Third International Future Mining Conference, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By A Sturgess, P McKenna, P D. Erskine, D Doley, V C. Glenn

For more than four decades, rehabilitated lands in the Bowen Basin have been planted with buffel grass (Cenchrus Ciliaris), which is often used to provide rapid, stabilising and erosion reducing cover to reshaped landforms (Erskine and Fletcher, 2013; Harwood, Hacker and Mott, 1999; Grigg, Shelton and Mullen, 2000; Naidu et al, 1997). Historically introduced to Central Queensland and encouraged by pastoralists in the early 1900s (Humphreys, 1967), the species has been extensively used by mine managers in seeding mixes (Coaldrake and Russell, 1970; Edye, 1975), and the invasive nature of the grass has led to the monodominance in rehabilitated areas of semi-arid Central Queensland. With 40 open cut coalmines in Central Queensland (Department of Natural Resources and Mines, 2015), a considerable amount of land is either disturbed mine footprint (156 200 ha) or rehabilitated (29 200 ha) (Dale, 2015), and the bulk of rehabilitation consists of relatively young (<30-year-old) developing ecosystems, with demonstrated biomass fuel loads up to 20 t/ha (Grigg, Shelton and Mullen, 2000).Uncontrolled fire poses a significant risk to rehabilitated landforms that are located in close proximity to mining infrastructure, neighbouring communities, open pits with exposed flammable coal seams and flammable stockpiled coal resource. Mine lease holders in Queensland have the added responsibility of managing and protecting any endangered regional ecosystem communities, and flora and fauna listed federally under the Environment Protection Biodiversity and Conservation Act 1999 or the State Vegetation Management Act 1999; as well as, any culturally significant sites such as scar trees or middens that are found on-site. Additionally, uncontrolled fire in rehabilitated landscapes poses a significant risk to mine site closure goals, with the potential to create altered states and stalled ecological trajectories (Grant, 2006). CITATION:McKenna, P, Glenn, V, Erskine, P D, Doley, D and Sturgess, A, 2016. Fire behaviour in buffel grass dominated mine site rehabilitation in Central Queensland, Australia, in Proceedings Life-of-Mine 2016 Conference , pp 158–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The capacity of chlorine based solutions to rapidly and effectively dissolve coarse gold in oxide ores is well established. The inherent advantages of chlorine are high dissolution rates (10 - 100 times those of cyanide), and low cost. The high dissolution rates mean that coarse or poorly liberated gold may be dissolved over relatively short periods and hence ore particle size may cease to be such a critical factor. The cost of size reduction to allow adequate gold liberation in order to achieve an adequate gold recovery is less of a consideration when using chlorine than in traditional plant or heap leaching cyanide-based treatment systems.Because chlorine based solutions capable of dissolving gold evolve an unpleasant vapour phase with the potential for significant chlorine losses into the atmosphere, traditional heap leaching with active solutions being sprayed onto prepared heaps is not possible. The ore must be covered and the solution may be introduced beneath that cover through prepared injection `wells' and recovered through production 'wells'. The pit is flooded with active solution beneath an overburden or cover with the solution migrating from the injection 'wells' to the production 'wells' over a period of around five - ten days.

Jan 1, 1992

Gravity gold recovery has been practiced for thousands of years, making it one of the oldest forms of mineral processing. Gold is 19 times heavier than water although the barren rock is generally only 2.7 times heavier. Any potential gold ore needs to be characterised to assess its amenability to a gravity recoverable gold (GRG) process based on well planned and executed test work. Scale up considerations need to be considered in designing a gravity circuit. The economic impact of a gravity circuit should be justified based on the installed cost and likely benefits. Maximising gravity gold recovery results in a faster cash flow, lower operating cost per ounce and higher overall gold recoveries compared to the several weeks required to recover gold adsorbed onto carbon. The advent of centrifugal concentrators such as the Knelson and Falcon, coupled with intensive leaching of concentrates (ILR), has revolutionised gravity gold circuit designs. Considerations associated with the sizing of the centrifugal machines and the percentage of the circulating load (bleed) that should be processed is discussed in this paper. The trends with gravity circuit layout, engineering, as well as optimum dumping cycles, are important areas which require close consideration. Key aspects of these are presented in this paper. There are a number of circuit configurations to be considered, including the integration of different gravity concentrators. Other gravity process design considerations such as fewer modules, the effect of equipment size and enhancement of process efficiency using preconcentration, together with factors that affect OPEX and CAPEX are addressed. Practical considerations of maintenance, security from theft, minimisation of risk and water balance considerations are discussed using different equipment and circuit configurations. The trend towards using gravity recovery in flotation plants is also reviewed. A number of examples are cited and good design aspects highlighted.

Aug 1, 2010