Search Documents

By B P. Banerjee, S Raval

In the recent past there have been dramatic advancements in the development of remote sensing platforms (satellite, aircraft and unmanned aerial vehicles – UAVs) as well as sensor systems (multispectral, hyperspectral, thermal, light detection and ranging (LiDAR) and radar). However, selection of the appropriate remote sensing technique for a mining application is complex and requires scrutiny on multiple scales including spatial, temporal and imaging capabilities. This presentation highlights various conventional and emerging remote sensing approaches over a mine’s life.CITATION:Banerjee, B P and Raval, S, 2016. Applications of advanced remote sensing systems during a mine life, in Proceedings Life-of-Mine 2016 Conference , pp 116–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A Scott, S Kanchibotla, J Segui

The æMine to MillÆ concept is not new. In fact, it is the underlying objective of every mine. Unfortunately, in many operations the management structure and reporting systems have created independent æbusinessesÆ within the overall mining enterprise. This has created incentives to optimise the performance of each component of the operation rather than the enterprise as a whole. The Mine to Mill Conference organised by The AusIMM in October 1998 documented a number of case studies where run of mine ore was not presented to the mill in the best possible form for subsequent stages of comminution and processing. A number of examples were quoted where modest expenditure in the mine had a very significant impact on downstream process efficiency and hence costs. Examples included:the minimisation of fines in the mining and handling of iron ore; the management of fines in blasting and crushing for a copper heap leach operation; the control of blast damage, mining recovery and dilution in open cut coal operations; and the optimisation of mine fragmentation to increase mill throughput in gold and copper operations. The latter topic has been trialed at a number of mines and is referred to as æMine to MillÆ fragmentation. A number of æMine to MillÆ type investigations have been reported in the literature including Pease et al, Simkus and Dance, Nielsen, Scott et al, Kojovic et al, Kanchibotla et al, Bulow et al and Hawkes from the 1998 Mine to Mill Conference. In addition, a number of studies are in progress or the results have yet to be published. These studies have demonstrated the feasibility of obtaining the data required to characterise the breakage behaviour of ores and to model the impact of changes to blasting practices on process efficiency. Characterising the breakage behaviour of ores is a vital step in the management of fragmentation and comminution in mines. The characteristics of importance to fragmentation fall outside the parameters conventionally required to describe the economic geology of a deposit. æMine to MillÆ optimisation of fragmentation means that the mining engineer needs information from the geologist in order to be able to help the metallurgist. Providing this information requires close interaction between these groups.

Jan 1, 2000

By Carlini G, Ibba R

The KSS Lead Plant (Kivcet - SNAMPROGETTI - SAMIM) of Por tovesme, owned by Nuova Samim (the sector-head Company for non ferrous metals and derivatives owned by ENI), has been operating since february 1987. This plant is based on the Soviet Kivcet licence and testwork carried out on the pilot plant of VNIITSVETMET in Ust Kameno gorsk fed by the Nuova Samim's concentrates. The plant is com pletely automatized using the most advanced technologies and it is operated by nineteen people on shift work, including all ancillary units and lead decopperizing-casting. The expected performance of the plant has been confirmed and improves day by day in relation of the operating experience, thanks to the new conceptual design of the furnace. Due to the remarkable flexi bility of the process, the integration of the lead plant with the other plants of the metallurgical complex of Portovesme rro-#4 (Electrolytic Zinc Plant, Sulphuric Acid Plant, Imperial Smel ting) has shown all the economic advantages. The lead content in the ambient air, detected by the monitors, either in the working area and on the ground outside the complex, is widely Pb W" below the stricter new limits recommanded by the E.E.C. (Economic European Community) rules and by the Italian law. The whole process is carried out in equipment completely closed and under suction and it does not require manual operations with exposure to the lead. The production cost is much lower than that performed by the traditional technology. This advantage permits wide margin to consider investment to replace the traditional technology.

Jan 1, 1989

By R McCarthy, P Darvall

FerrAus Limited's Robertson Range and Davidson Creek iron ore projects are located on the far eastern margin of the Hamersley Province, approximately 100 km to the east of Newman, Western Australia. The deposits are primarily formed of bedded haematite-goethite-limonite mineralisation within the Marra Mamba Formation, comprising a total combined resource of 164 Mt at 58.6 per cent Fe. The deposits represent relatively new discoveries for the Hamersley Province. The potential for mineralisation at Robertson Range was identified by Rio Tinto Exploration in 2000, while Davidson Creek remained untested until 2007. One of the main reasons for this is that these deposits are almost exclusively concealed beneath Tertiary sediments and recent transported cover making them difficult targets for conventional, prospecting style exploration. Since commencing exploration in the project area, FerrAus has collected nearly 20 000 stations of gravity data within the Robertson Range and Davidson Creek project areas, with most of this data collected at a 50 100 m station spacing. Gravity has proven itself to be an effective technique at predicting the position of the target host stratigraphy and has been a key driver in the exploration for concealed iron ore deposits. However, there is not always a perfect correlation between the position of gravity anomalies and concealed ore. The response of deep haematite bodies may be masked by low-density cover rocks, while other dense lithologies may be the cause of gravity anomalies which appear similar to the Marra Mamba targets. Hence, effective use of the gravity data requires interpretation in a geologic context with an understanding of the capabilities and limitations of the technique.

Jan 1, 2009

Roller seed screens were installed at The Broken Hill Proprietary Company Limited (B.H.P.) Whyalla pellet plant to replace vibrating screens on the green ball circuits. The installation of roller screens was justified by improving the sizing of the green balls. This improved sizing increased the yield of fired pellets produced from green balls thus decreasing the fuel consumption. The fired pellet sizing was improved also. This paper discusses the configuration of the roller screens installed at Whyalla, quality of green balls produced, advantages of roller screens compared with vibrating screens and future development of roller Screens.

Jan 1, 1984

By A Specht, A Müller, V Montenegro, S Winkler, E Klaffenbach, A Schmidt

In the process of primary copper smelting in flash smelting furnace (FSF), the ratio of iron to silica (Fe/SiO2 mass ratio) primarily determines the slag viscosity and magnetite formation. Viscous slag does not only cause difficulties in daily operation, such as in tapping, it also increases the copper losses to slag. Thus, keeping the Fe/SiO2 mass ratio at the desired level is an important aspect of FSF and slag cleaning furnace (SCF) operation. In this study, the improvement of the Fe/SiO2 mass ratio was conducted in two steps: First, the optimal Fe/SiO2 mass ratio was derived based on thermodynamic data. Based on this analysis, appropriate control limits were determined. Second, this range of favourable Fe/SiO2 mass ratios was implemented into operation by an advice-based control system, which suggests the addition of silica based on the analysis of SCF slag. As this approach was successful, the same advice-based control system principle was adapted for the coke addition to the SCF. After testing the new advice-based control for several months, the production data confirm the predictions by thermodynamics: since the prediction was implemented as an advisor, the copper and magnetite content in SCF slag is significantly reduced and viscous slag is reported less often by operations.

Aug 21, 2024

By G Solly, S Parsons, P Leevers, S Ni

Hematite ore has been mined in the Southern Middleback Ranges as blast furnace feed for the steelworks at Whyalla, by what was then BHP, since 1991. With the floating of BHP Integrated Steel as OneSteel in 2001 and the subsequent loss of key mining personnel, breakdowns in grade control methods and procedures occurred. These were compounded by changes in orebody characteristics and grade distribution leading to poor reserve recovery and poor grade control, both which resulted in loss of control of ore specification and severe deviation from the mining schedule. As a result, a total review of grade control, mining method and scheduling procedures was undertaken as well as a review of contractor quality assurance. It was found that sampling methods were poor and unrepresentative, grade control blocking processes were outdated and did not reflect the geology of the deposit, the ore mining method was outdated and did not respect the geometry of the orebody, reconciliation methods were being completed globally and were not reflective of individual areas of the deposit, and that deviations from the mine plan were occurring due to access to high-grade areas outside the schedule in order to bring stockpiles back on grade. Based on these findings, updated sample splitter systems were fitted to drill hole rigs, double bench sampling was implemented (2 + 4 m samples as opposed to 1 + 8 m sample) and a three-dimensional cellular grade control system introduced to better reflect the geology and orientation of the deposit. At the same time ore mining was changed from front end loaders mining on 8 m benches to excavator mining on three lifts on 8 m benches; this aided selectivity and respected the geometry of the orebodies aiding cleaner recovery. Reconciliation is now completed on a blast-by-blast basis, which allows for quick and easy identification of poorly performing areas of the resource model that can then be incorporated back into resource model updates. Regular daily and weekly meetings are also held with emphasis on the mining schedule to ensure no deviation from the schedule in the long term. These improvements have resulted in a lift in reserve recovery both globally and locally associated at the same time with improvement in grade.

Jan 1, 2005

By Madgwick J

A novel method for determining viable cells of the mineral leaching bacterium Thiobacillus ferrooxidans has been developed. The cells were collected on 0.45/Lm cellulose acetate filters, washed with artificial minewater, and incubated in the presence of ferrous ion at pH3 in an atmosphere containing radioactive (14C) carbon dioxide. Colonies of bacterial growth were detected by the image formed on X-ray photographic paper (autoradiography). The method was compared with three conventional techniques and shown to detect three orders of magnitude more cells in cultures of Thiobacillus ferrooxidans in the late exponential phase of growth.

Jan 1, 1987

By L Nagy, K P. Juhasz

The authors were engaged to optimise a traditional rebar cage reinforced concrete segmental lining by means of finite element analysis (FEA) using macro synthetic fibres for the Shanghai metro extension. The aim of this study was to reduce or entirely replace the original steel reinforcement of the segmental lining, in order to make the precast production process faster and more economic. The outer diameter of the tunnel was 6200 mm, the thickness of the segments was 350 mm.The numerical calculations were performed by Atena Finite Element software, which is based on the combination of Menétrey-William and Rankine failure surfaces on the compression and tension sides respectively. The effect of the macro synthetic fibres was modelled as tension stiffening on the tension surface.A one-to-one full scale model of an assembled tunnel ring using the original reinforcement cages was tested at Tongji University in Shanghai, July 2013. The ring was tested to differing load levels where load and displacement were measured until failure. The author’s first step was to calculate the real displacement characteristics of the original reinforced concrete (RC) ring, then calculate the numerically modelled version, so as to compare them. The material parameters of the concrete and rebar used had been determined through basic material tests conducted at the Tongji University. (Bi, Liu and Wang, in press).The numerical modelling undertaken has shown good correlation with the full-scale physical test results. Optimisation of the lining reinforcement was achieved through the addition of fibres, resulting in a substantial reduction of the steel rebar cages. Several results have been computed with the numerical model using different dosages of macro synthetic fibres, showing that the mass of steel reinforcement could be reduced by 50 and 75 per cent respectively.CITATION:Juhasz, K P, Nagy, L and Winterberg, R, 2014. Full-round numerical modelling of a macro synthetic fibre reinforced tunnel boring machine tunnel in the Shanghai Metro extension, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D David

The development of Western Australian magnetite deposits has lead to the design of some of the largest grinding mills and plants in the world. One of the projects demonstrates the efficiency gains possible by developing a simple yet thorough test program for circuit design. By drawing on the experience of current magnetite operations in Australia and the Mesabi and Marquette iron ranges in the United States, a basic flowsheet was developed. Through comprehensive testwork with AG, ball and stirred milling the flowsheet was optimized to take full advantage of each grinding mill’s strengths to reach the required final grind size. Laboratory work was verified in the pilot plant to optimize the energy efficiency of each grinding step while ensuring adequate liberation at each step for sufficient gangue rejection. By using three stages of grinding, the ball mill can best be employed in ensuring all top size gangue material is liberated and removed in the second magnetic separation step. The inclusion of the IsaMill, with its inherent steep product size distribution, as the tertiary grinding stage ensured that maximum grade was achieved and simplified the downstream process while giving further improvements in total grinding capital and operating costs. In this way the combination of the two technologies downstream from the AG mill is far more efficient than either would be on its own by reducing the total installed power by 1/3 and annual grinding media cost by 2/3.

Aug 8, 2011

The Rock Mass Rating (RMR) and Rock Mass Strength (RMS) classification systems for jointed rock masses are briefly reviewed, with particular reference to their use in slope stability studies. A correlation is provided between the results obtained from the two classifications and an equation is presented tentatively defining the RMR value for long-term stable slope angles. The validity of the equation is discussed in general terms in the context of slope stability problems commonly encountered in Western Australian open pit gold mines.

Jan 1, 1992

By Hunt MS

A major diamond mining operation in South Africa is faced with the unique problem of recovering usable water from the fine tailings stream. The kimberlite ore hoisted is washed prior to crushing in order to remove adhered fine clay particles. These particles form a colloidally stable suspension from which it has not been possible to recover clear recycle water. Research has been conducted on this problem for more than 20 years and it is only recently that a breakthrough has been achieved. This paper describes the work done to gain an understanding of the suspension stability and which subsequently led to the testing of a process at pilot-plant Scale.

Jan 1, 1988

Upon subduction, water is liberated from the sediments and the porous struc- ture of the oceanic crust and from de- hydration of minerals for redistribution and chemical reaction. A survey of pro- cesses which are likely to occur along the subducting plate reveals that water may well be basic in subduction induced gas generation, magma formation and ore deposition. In analogy to the industrial water gas process, reaction of water with car- bonaceous matter, in subducted sediments is likely to yield substantial volumes of hydrogen and carbon dioxide. While water and carbon dioxide appear to play a determining role in the development of differentiated magmas, hydrogen will react with metal sulfides and sulfur to form hydrogen sulfide which is essential in sulfide ore depo- sition. A survey of possible metal extrac- tion chemistry along subduction suggests a stepwise solubilization of metals from sediments and oceanic crust, and a poten tial accumulation of dissolved metals in zones of characteristic composition. The metal spectrum in ore deposits at near surface appears to reflect the com- position of the solution in the respec- tive subduction zone. A tendency for preferential solubi- lization of copper at subductidn level, from among the transition metals, an in- creasing generation of hydrogen sulfide in the sane direction and partition effects as well as sulfide precipitation characteristics lead to enrichment in copper and to its selective deposition in the direction towards the trench as observed in S. Latin America. A postscript deals with the formation of native copper.

Jan 1, 1986

By Rogers M, Sullivan B

Golden Crown Mine is a narrow vein gold mine producing 75000 tpa. Production has been predominantly by shrink stoping using hand held machine and airleg. Bogging from these stopes is done with Toro 150 LHD units.Previously the standard development method consisted of developing a sill drive, a footwall drive and millholes every 7 m. This meant that for every metre of ore development, 2 m of waste development was required.

Jan 1, 1993

High sulphur volcanic-hosted hydrothermal environments are favourable geological environments for gold mineralisation. Numerous world-class gold deposits including Pueblo Viejo (Dominican Republic), Goldfield (Nevada), EI Indio (Chile), and Wa

Jan 1, 1994

Fluid bed sulphation roasting followed by leaching at low pH was developed as a means of separating copper and bismuth from a mix- ture of flotation concentrates and flash fur- nace flue dust. A 65 tonne/day plant was established and typically achieves 89 percent copper extraction with negligible bismuth and iron extraction. Acid-chloride leaching of bismuth from copper leach residue was then established, with bismuth oxychloride being precipitated from solution by dilution with water. A small scale batch plant presently in operation typic- ally achieves 80 percent recovery of bismuth to bismuth oxychloride.

Jan 1, 1986

By Henderson J, Ward RG

Dissolved oxygen has been measured directly using a rugged, reliable, accurate electrochemical probe system developed for steelworks application by B.H.P. Central Research Laboratories. Furnace measurements show that the steel is generally supersaturated with oxygen and that oxygen contents vary considerably from heat. to heat. Ladle measurements also show considerable heat-to-heat variations. Analysis in terms of ladle deoxidation chemistry differentiates between carbon monoxide controlled and manganese silicate controlled oxygen levels. Deviations from these levels are sometimes due to aluminium present in other added ladle alloys but in some cases the plant applicability of laboratory derived equilibria is questionable.

Jan 1, 1972

By Thuli AJ

Copper concentrate from Bougainville's copper mine located on the west slope of the Crown Prince Range on Bougainville island, is pumped 27 km to the filter and drying plant at Anewa Bay for preparation and storage prior to shipment to overseas customers. Prior to shipment the thickened concentrate slurry is passed through a test loop to check that its consistency and pH are acceptable for transportation through the main pipe line. The Bougainville pipe line is unique since it is the world's first copper concentrate system. where slurry is pumped an appreciable distance against a high head,

Jan 1, 1975

During 2009 the technical services staff at Barrick Gold Corporation's Australian Business Unit conducted a review of their five underground mines that utilise pastefill as the backfill component for these operations. Of the five mines reviewed three use dry tailings and two use wet tailings plants. The primary aim for these reviews was to determine whether pastefill was the right option to be used, and if not, what where the alternatives. The reviews undertaken focus on several areas including, paste plant operation, reticulation and barricade techniques, the geotechnical requirements for pastefill in regards to the current mining methods, the consideration of alternative methods, capital and operating cost histories compared to initial estimates, and a cost benefit analysis of pastefill against other mining methods. The main benefits from the use of pastefill is increasing the extraction of the resource, reducing or eliminating the need to leave pillars. In some mines the use of pastefill is geotechnically driven, to manage high stress environments or mining induced seismicity. A third benefit of using pastefill in some circumstances is that it reduces dilution, however it is considered that this is not a valid argument for most of the mines reviewed. At two mines no alternative to pastefill was determined, whilst differing extraction and filling strategies were potentially identified at the other three mines. The reviews developed cost benefit curves for those sites that had alternative mining methods to assist in determining whether pastefill is the right option to use for any particular stope. At the grades typically mined in each operation, pastefill was the preferred option to use. In all mines, pastefill was determined to be the best option at this time.

Nov 25, 2010

By A Sadri, S Smith

In the metal and mineral industry, different empirical techniques are used to estimate the remaining thickness of the lining within an operating furnace. The disadvantage and costly factor when using these methods is that production needs to be halted. Hatch has developed an accurate and reliable technique based on stress wave propagation principles to determine the condition of the remaining lining whilst the furnace remains online and operational.The technique involves test data collected and compiled to generate 3D imagery used to assist operators and maintenance planning personnel with valuable information showing areas of metal penetration in the lining, remaining lining thickness, exact location of voids, cracks, poor contacts and deterioration due to chemical attack. In this paper, the principals of the AU-E technique will be explained both theoretically and practically. In addition, the use of ultrasound technology for determining the condition of copper cooling elements will be briefly addressed.

Jan 1, 2006