Search Documents

By M Kuruppu, B Besa

Currently, conventional methods of decline development put enormous cost pressure on the profitability of mining operations. This is the case with narrow vein orebodies where current methods and mine design of decline development may be too expensive to support economic extraction of the ore. The time it takes to drill, clean and blast an end in conventional decline development can be up to 473 minutes. This is because, once an end is blasted, cleaning should first be completed before drilling can commence, resulting in low advance rates per shift. Improvements in advance rates during decline development can be achieved by application of the electric monorail transport system (EMTS) based drilling system. The system is composed of a two-boom drill mounted on the monorail and a pneumatic face cleaning system that loads blasted material into monorail containers. The operation allows for drilling of the top part of the face to commence as the monorail loading system continues to clean the blasted material at the development face. The preliminary indication is that an advance rate of 12 m per day could be achieved compared to 6 m per day in conventional decline development. The increase in the advance rate results from increased number of blasts that are possible per shift due to reduced time of cleaning and drilling the development face. The continuous drilling system has the advantage of accelerated decline development and orebodies will be accessed quickly and cheaply. Other advantages of the system include negotiating steep and changing gradients (ie reducing decline length), ability to negotiate tight horizontal curves, small operating room and limited diesel fumes.

Jan 1, 2008

By M Stephens, T A. Sutra

Currently, there are several open pit mines with production rates of about 200 000 tpd of ore that are reaching the end of their economic lives. In most cases, the remaining orebody extends to depths greater than 300 m below the pit limit, leaving hundreds of millions of tons of reserves that can only be recovered by means of an underground mining method. One such method used for mass production is block caving. This paper presents a ventilation system for a four-zone block cave mine operation developed on a footprint 1000 m wide and 1200 m long. The system is designed for a mine with a nominal production rate of 120 000 tpd of ore using diesel powered units on the production and reduction levels. It discusses the air quantity requirements for the worst case scenario, which is anticipated to occur five years after the mine has reached its full production capacity. Finally, it summarises the results of computer modelling exercises that were carried out to determine an economic ventilation infrastructure that includes shafts, drifts, main fans, and ventilation control devices.

Jan 1, 2005

Shear strength testing of rock discontinuity surfaces has been undertaken at a considerable number of open pit gold mining operations in Western Australia, as part of geotechnical studies of pit wall stability. These mining operations are located in geological settings that are typified by highly weathered and/or chemically altered rocks that contain significant structural fabric in which accurate and representative measurement of shear strength is essential.Little of the published rock discontinuity shear test work and back-analysis of failures has been conducted on weathered discontinuity surfaces, at low normal stress levels which are comparable to Western Australian conditions. Available shear strength data are reviewed and the following aspects of shear strength testing are considered:ò the need for shear strength test work and the amount of testing required;ò review of laboratory testing methods and the quality of the results; ò presentation of the test results;ò discussion of the shear strength failure criteria; ò interpretation of the test results;ò summary of test results for a variety of rock types, degree of weathering and discontinuity surface conditions;ò a review of laboratory and field shear strength data to illustrate the amount of variability that can occur; andò a monitoring strategy is proposed to manage the uncertainty associated with discontinuity shear strength.

Jan 1, 1992

By Doyle P, Mulroney D

The Cassidy Shaft was sunk to access the Mount Charlotte and Reward Orebodies below the Flanagan Fault. The 1,184m deep shaft is concrete lined to 6.5m diameter for its full depth. The initial 590m was excavated by stripping into a 1.8m diameter borehole and hoisting the broken material through the existing mine. The remaining 594m was excavated by conventional shaft sinking methods. The shaft was sunk through 3 existing plats and an additional 8 plats cut. 1,800 tonnes of steel and 8 cables were installed during the furnishing of the 4 compartments.

Jan 1, 1985

By MacDonald AJ, Raffield MP

The South Deep massive orebody consists of 20 to 30 in of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 in and 34(10 in. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse arious scenarios to aid in the decision process.

Jan 1, 1998

The Yanacocha district hosts the largest and most significant acid-sulphate, high-sulphidation deposits in Per· with total production, reserves and resources of over 27 million ounces of gold. Several other smaller high-sulphidation systems are also recognised in the Cajamarca region including La Zanja, Sipßn, Tantahuatay, and San Nicolas. These each have reserves/resources of between 640 000 and 800 000 ounces of gold. Gold deposits in the Yanacocha district are hosted in an extensive volcanic field. Flow domes have intruded precursor pyroclastic rocks and flows that are interpreted as part of an earlier intermediate multi-vent volcanic complex. The larger, contiguous Yanacocha Norte - Sur and Encajon gold deposits are spatially associated with late-stage diatreme breccias. At La Zanja extensive acid-sulphate alteration is associated with the margins of the small San Pedro caldera (6 +4.5 km), nested within the larger, less well-defined La Zanja caldera (19 +24 km). The inner caldera is resurgent with abundant magmatism expressed as several flow dome complexes located on the caldera rim, and shallow level intrusive stocks. Gold mineralisation is associated with a WNW-trending structural corridor that transects the southern margin of the San Pedro caldera. On the eastern side of the La Zanja caldera there are a series of younger andesitic eruptive centres, some associated with acid-sulphate alteration and gold mineralisation. The Sipßn deposit occurs in one such centre with structurally-controlled gold associated with a NE-trending silicified structure developed within a sequence of andesitic tuffs. In conclusion, although a number of high-sulphidation deposits are recognised in northern Per·, their settings and styles of mineralisation are all quite different. Smaller deposits generally have strong and obvious structural controls. In the larger Yanacocha deposits the structural controls are less obvious, and mineralisation is disseminated in porous or strongly fractured and brecciated silica. Erosional levels are probably a significant factor, with disseminated mineralisation at higher levels, and structurally-controlled mineralisation in more deeply eroded deposits.

Jan 1, 1999

By Vynne J. F

Drill monitors for rotary blasthole drills have been available to the mining industry since the 1970s. The early monitors were pen strip chart recorders that were developed for the oil drilling industry and adapted to mining. They recorded drilling parameters such as depth, pull-down pressure, torque, RPM, and hailing air pressure. While these recorders could generate a large volume of paper, the amount of useful data was minimal. The data was not summarised and required an engineer to interpret the chart traces. Being a mechanical recorder, the devices were also susceptible to frequent failures. Modem electronics, and the development of the personal computer and its associated software have radically changed the type of instrumentation that is now available for blasthole drills. Perhaps more important is what can be done with the data. The PC allows the logged data to be analysed, summarised, and a variety of reports to be generated. The reports can be customised to meet the specific requirements of the mine and reduce the amount of time that is required to interpret the data. There is also an increased awareness in the mining industry of the importance of production drills. Blasthole drills have typically been the piece of production equipment that received the least amount of attention in a surface mine. Management focussed on the trucks and shovels or draglines. This situation is changing, and therefore the benefits that can be derived from monitoring drill performance are being recognised. Potential economic benefits of installing drill monitors have been documented in previous papers (Peck and Vynne, 1992). Mines are finding that pay-back periods of less than twelve months and rates of return in excess of 30 per cent are not uncommon. These benefits include the following: 1. Reduced overdrilling; 2. Increased rate of penetration; 3. Helping to locate coal seams; 4. Identification of weak and strong zones; 5. Reduce geophysical logging; 6. Optimising blasts; 7. Improved fragmentation and diggability; 8. Decreased coal dilution; 9. Increased bit life; 10. Reduced maintenance costs; 1 I . Improved accuracy of data and reports.

Jan 1, 1995

By A K. B Opitz, M Becker, J L. Broadhurst

"One of the key drivers of geometallurgy is to define the ore characteristics and their variability to build a geometallurgical model. The inclusion of waste rock properties and their variability is just as important, given that the generation of acid rock drainage (ARD) poses one of the most significant environmental challenges facing the mining industry. Formed through the oxidation of sulfide minerals in the presence of oxygen and water, ARD generation is exacerbated through the regeneration of lixiviates by naturally occurring iron- and sulfur-oxidising micro-organisms. In order to manage the potential risk of ARD pollution, timely, accurate, reliable and robust characterisation and prediction of the ARD potential of waste material is critical from an early stage in the mining process.This study demonstrates the use of the biokinetic-accelerated weathering test developed at the University of Cape Town to characterise the ARD potentials of gold waste rock samples under microbial conditions. These tests are performed in conjunction with standard characterisation tests to provide an indication of the potential for ARD generation under both chemical and biological conditions. Results provided information regarding the relative rates of acid neutralisation and acid generation, with the contribution of specific minerals to the observed behaviour considered through use of a detailed mineralogical assessment. Overall, the addition of the biokinetic test to the current geometallurgical characterisation and prediction toolbox will allow for relatively rapid assessment of the bulk kinetics of ARD generation.CITATION:Opitz, A K B, Becker, M, Broadhurst, J L, Bradshaw, D J and Harrison, S T L, 2016. The Biokinetic Test as a Geometallurgical Indicator for Acid Rock Drainage Potentials, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 183–192 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Many types of micro-organisms inhabit iron ore deposits contributing to biogenic formation and conversion of iron oxides and associated minerals. Bacteria such as Paenibacillus polymyxa are capable of significantly altering the surface chemical behaviour of iron ore minerals such as haematite, alumina, calcite and silica. Differing mineral surface affinities of bacterial cells and metabolic products such as proteins and polysaccharides can be utilised to induce their flotation or flocculation. Mineral-specific bioreagents such as proteins are generated when bacteria are grown in the presence of haematite, alumina, calcite and silica. Alumina-grown bacterial cells and proteins separated from such cells were found to be capable of separating alumina from haematite. Biodegradation of iron ore flotation collectors such as amines and oleates can be effectively utilised to achieve environmental control in iron ore processing mills.

Jan 1, 2009

This paper deals briefly with three of the more controversial aspects of the geology of the Mount Isa ore deposits namely the geologic structures, the method of ore deposition and the origin of the ore.In the section on geologic structures, an outline is first given of the purely tectonic deformation advocated by the early authors. The current interpretation, which differs in the proposed order of events and causal forces, is then discussed. Other concepts, which attribute all or part of the deformation to sedimentary features or preconsolidation movement, are outlined ilnd commented on.The remaining two sections deal mainly with the better known lead-zinc orebodies. In the first of these a brief description and criticism is given of the early interpretation which was based on the deposition of successive waves of mineralisation which replacedindividual beds in the shales. The current ideas, which visualise emplacement of the ore between the beds rather than replacement of them, is then discussed. The final section develops the case for a sedimentary origin of the lead-zinc ores and broadly outlines the author's ideas concerning the evolution of the Mount Isa ore deposits.INTRODUCTIONAny consideration of the geology of Mount Isa must begin with the work of Blanchard and continue with that of Hall. Individually, or as co-authors, they published various papers on the geology of Mount Isa. Of these, the best known is their "Rock Deformation and Mineralisation at Mount Isa" (1941) which gave a comprehensive account of all aspects of Mount Isa geology.It is necessary to appreciate the limits set on geological knowledge of the mine and environs in 1941 by the extent of mine development and regional geologic studies. Underground, 7 level (897 ft.) was the lowest producing level. Development on 8 (1073 ft.) and 9 (1247 ft.) levels consisted only of exploratory drives and crosscuts in the vicinity of the Davidson Shaft. The tops of the 650 and 750...

Jan 1, 1961

By S J Riley

The cover (cap) over the tailings pit at Nabarlek uranium mine must be structurally stable as it will act as a barrier to radon gas emission and have to contain other long-lived radionuclides. Structural stability is primarily an issue of erosional stability in the context of a design life of thousands of years. The primary agent of erosion is fluvial, dominated by rainwash, overland flow, filling and gullying in the local area. Other agents of erosion are of less concern although biogenic agents of erosion (eg termites and windthrow) may enhance fluvial activity. Several methods may be used to assess erosional stability. They fall into two main categories, namely erosion modelling and geomorphic modelling. The former is illustrated by the Universal Soil Loss Equation in which parameters describing aspects of the geotechnical and hydrological properties of the rehabilitated surface are used as input for the modelling of erosion rates. The latter is illustrated by estimates of gully and valley erosion using empirical models. Estimates of the erosion rates and stability of the Nabarlek cover are presented. The two main techniques are complementary and it is argued that rehabilitation design must make use of both approaches when estimating erosion and geomorphic stability. More recent developments in geomorphic modelling using numerical techniques incorporate both approaches.

Jan 1, 1994

By S Serp, M Duchateau, P Chevreux

Molten salt reactor (MSR) is a promising advanced reactor system aiming to the transmutation of minor actinides such as americium in order to reduce the inventory of ultimate nuclear waste. The fuel is a molten salt in which actinides are homogeneously dissolved in the liquid phase. A chloride salt may be retained for this concept, as it provides low melting point, high solubility of actinides, harder neutron spectrum. To avoid corrosion and precipitation issues, molten salt composition has to be carefully controlled with impurity content as low as possible. Obtaining pure actinide chlorides without contaminants such as oxide, oxychloride, hydroxide and water is still a challenge. To prepare actinide-bearing salt, the chlorination of actinides oxides was investigated in an unstirred reactor under flowing gas as solid-gas reaction. The carbochlorination of PuO2 were performed in the temperature range of 600 to 800°C with chlorine gas as a chlorinating agent and the presence of solid carbon. PuCl3 was successfully synthesised by this method and characterised by X-ray diffraction measurements but some impurities such as oxide phase remain inside the formed product. Refinements of anhydrous and hydrated PuCl3 phases by Le Bail method were also performed for crystalline materials definition. Conversion mainly depends on the chlorinating temperature and the contact between the oxide and the chlorinating agent. A conversion value of 70–80 per cent was achieved at 700°C from PuO2 with quite high specific surface area. The conversion rate was not improved with increasing the chlorination time. The volatilisation of Pu was observed during the carbochlorination experiments. To avoid a loss of Pu caused by sublimation, the chlorination temperature should be limited to 650°C despite that the conversion of PuO2 to PuCl3 was enhanced by increasing temperature. Both carbochlorination and hydrochlorination of AmO2 were also carried out leading to the formation of AmCl3. These first results suggest that americium oxide was chlorinated more readily than plutonium oxide. The purity of produced PuCl3 and AmCl3 still deserves further investigations.

Jun 19, 2024

By J G Bastias

It is sometimes necessary to resort to extremes in order to call attention to something that is pertinent to safety in mining. When some of the experts in occupational safety talk about this topic, they usually refer to a 'regulation' established by the Romans which stated that, due to the health hazards, usually death, no Romans but only slaves should work in mining. Since the time of the Roman Empire, a lot of ground has been covered in the field of mine safety. Nowadays, it can be said that occupational safety is being seriously addressed, with the result that the number of mining accidents has reduced dramatically, fatalities in this industry are less frequent, and the rate of accidents compared with other activities, such as construction or fanning, is low. This achievement has been possible initially through government legislation and by procedures established by the mining companies themselves. However, the dilemma for government is whether to regulate and if so, how much. It is pleasing to observe that most companies are establishing working procedures which conform with new government legislation, placing strong emphasis on the duty of care for mine employees. There will always be some regulatory aspects of legislation, and perhaps the best example of this is in the use of mine hoists where there are no international or Australian standards, and the regulations applied are of an empirical nature that err on the side of safety.

Jan 1, 1994

By J S. J van Deventer, D C. Shallcross

New developments are taking place in the recovery of gold from leached pulps that are based upon the adsorption of the metal cyanide species onto ion exchange resins. Despite the success of several resin-in-pulp pilot plant operations in the Western World and large-scale plants in the former Soviet Union, the process is yet to gain recognition as a viable alternative to the carbon-in-pulp process. An experimental research program has investigated the use of a variety of different types of resins for the recovery of gold, but to-date no resin studied has the desired properties of high selective loading capacity for gold cyanide and a simple inexpensive elution procedure. In addition very little is known concerning the physical strength of resins and their ability to resist shattering due to osmotic shock during cycles of adsorption and elution. The ability of ion exchange resins to enhance the leaching of refractory and re-adsorbing ores has not been investigated. This paper highlights the necessary factors that need to be addressed before commercialisation of ion exchange technology for gold extraction is feasible.

Jan 1, 1998

By H Kundapen, B R. Bolton, H Davies

The Ok Tedi porphyry copper-gold mine is located in the Star Mountains of Western Province, Papua New Guinea. Open-cut mine commenced in 1984 and is due to cease around 2010. The mine produces a total of 88 Mt of waste annually including 58 Mt overburden and 30 Mt tailings, which are discharged directly in to the Ok Tedi River. Mine derived wastes are transported downstream and deposited within the river channel in a variety of bar forms. The prevailing hydrogeological conditions including, velocity, competency, capacity, gradient, grain size and specific gravity, control the deposition and segregation of these sediments. Periodic exposure of the reactive sulfides to oxygen during fluctuations in the river discharge may result in oxidation, localised acid generation and liberation of metals into solution. To evaluate the significance of this issue, Ok Tedi Mining Limited initiated an investigation of the sediments deposited in the upper Ok Tedi River as part of its overall ARD Management Program. The specific objectives were to: evaluate the acid-forming characteristics of identified high sulfide river deposited sediments; characterise geochemically the waters in contact with sulfide-bearing river deposited sediments; map and monitor exposure areas and oxidation depth of deposited potentially acid forming (PAF) sediments; determine the depositional processes controlling sulfide distribution; and assess lag period, oxidation and metal release rates for the sediments. This work included the analysis of sediment and water samples collected on a 50 + 50 metre grid at six gravel/sand bars. The sediment samples were analysed for total sulfur, ANC, NAG, total sulfur and total copper. Water samples were tested for general water quality parameters, sulfate and a suite of dissolved metals including; Al, Ca, Cd, Cu, Fe-sol, K, Mg, Mn, Na, S and Zn. This paper presents the results of these investigations with particular emphasis on the geochemistry of the river sediments and associated contact waters.

Jan 1, 2003

By J Garritsen, P F. Wells, M Xu

IncoÆs Clarabelle mill currently processes ores from eight mines in the Sudbury basin area in Ontario, Canada. The ore from the Garson mine contains a much higher concentration of arsenic than the other ores. Adding this ore into the feed to the mill has resulted in an increase in arsenic content of the Cu-Ni bulk concentrate to a level that significantly affects the smelter operation, and more importantly the efficiency of Cu-Ni separation in the Matte separation plant. The arsenic occurs mainly as gersdorffite (NiAsS), with a small amount being in the form of cobaltite (CoAsS). Extensive laboratory tests on depressing arsenic in Garson ore flotation have been conducted and two reagent suites have been identified as effective arsenic depressants. One is the so called MAA depressant which is a mixture of magnesium chloride, ammonium chloride, and ammonium hydroxide. This reagent combination was reported to depress other arsenide minerals such as arsenopyrite (FeAsS) and enargite (Cu3AsS4). However, in this study for the first time it has been shown to have a depressing effect on gersdorffite. The other reagent suite, a mixture of triethylenetetramine (TETA) and sodium sulfite, that has been reported as an effective pyrrhotite (Fe1-xS) depressant in pentlandite ((NiFe)9S8) flotation, has not been reported as gersdorffite depressant before. The effectiveness of both reagent suites is more pronounced when the arsenic minerals are oxidised through pulp aeration or the addition of hydrogen peroxide. With a flow sheet consisting of a magnetic separation, rougher- scavenger flotation, followed by regrinding and cleaning of combined magnetic and scavenger concentrate, the arsenic recovery to the final Cu-Ni bulk concentrate was reduced from 73 per cent in baseline test to less than 30 per cent with either reagent suite at no decrease in nickel recovery. The TETA/sulfite reagent combination has the advantage over the MAA suite in that pyrrhotite is also depressed, rather than being activated, and the copper and nickel concentrate grades are therefore increased.

Jan 1, 2005

By G C. Reed, J M. Murray

During more than 100 years continuous mining of the lead-zinc orebody at Broken Hill, an immense amount of geological data has been collected about shear zones related to the orebody. The challenge to current mine geologists is to synthesise and interpret these data sets in a way that is applicable to production demands. Precise knowledge of the locations of major shear zones is important not only for the determination of ground conditions but also to develop an understanding of ore remobilisation along these structures. Traditionally, geological information has been collected from drill core and back and wall mapping underground, and interpreted on sections that are approximately 20 m apart. The recent introduction of MaptekÆs Vulcan software has enabled the shear zones to be modelled in three dimensions. The new three-dimensional shear models have been combined with seismic data from the Southern Cross area. The seismic data is collected from a microseismic monitoring system installed in the Pasminco Southern Operations in August 1996 (Rauert and Tully, 1998). The addition of seismic information to the shear zone models has led to a greater degree of certainty about the shear zone locations and has provided information about shear zones in areas yet to be drilled.

Jan 1, 2000

Operating metallurgists spend a significant part of their time running plant trials to compare two or more conditions in order to improve the process, such as a new reagent, flow sheet or piece of equipment. The best way to conduct such a trial is as a paired experiment when testing two conditions (eg 'old' and 'new') or a randomised block design when testing more than two conditions. These experimental designs should always be preferred over alternatives if their requirements can be met, because they block the effect of uncontrolled variables ('covariates') and are the most statistically efficient, ie they will lead to the required level of confidence in the outcome faster than other methods. Sometimes, however, it is not possible to switch condition easily, which is a prime requirement of these methods. In such cases the only option may be to switch condition once only, and compare the process performance before and after the switch. Examples are testing grinding media, large equipment, or long residence time processes such as leach trains or CCD thickeners. This paper considers some data analysis methods to deal with this situation. Modelling with intervention analysis (IA) uses regression models with a dummy variable to indicate the presence or absence of the test condition. IA with a time series model ensures that the residuals are uncorrelated. IA with a process model helps to deal with the problem of covariates. The reference distribution is a method free of any statistical assumptions but is less powerful than the other methods. Cusum charts are a helpful visual aid to interpreting time trends. A combination of these methods can help improve the confidence in the final decision. None are as good as a formal experimental design such as a paired trial.

Jan 1, 2008

By S Matos Camacho, K G. van den Boogaart, R Tolosana Delgado, U Mueller

"The precise formulation of a geometallurgical optimisation problem is by necessity a simplification of reality. It includes implicit choices such as data availability or mining block geometry. Additional data can be orebody data, production data or market data. Often these choices are predetermined by the software, the workflow or the corporate culture, and as such are not even queried. There are several aspects that might play a role in the optimisation. They include not only the spatial model on which the selection of mining blocks and the potential mining sequence are based, but also the complexity of the processing model, the way in which uncertainty is treated, the scope of responsibility and the complexity of the model. In addition the timing of the optimisation and the availability (or lack thereof) of information will influence the outcome of any optimisation.We show that different modelling choices and different model formulations for the same mine can lead to very different processing choices, substantially different net present values (NPV), opposite investment decisions and so to overall different values for the entire operation. The selection of adequate simplifications and corresponding formulations for the optimisation problem is thus an important task in itself.For this purpose we introduce a method for quantifying the impact of certain simplifications prior to the optimisation. For example, the effect of mining block choices depends mainly on the spatial structure and the structure of the processing gain function. Both can be quantified beforehand. Based on the outcome, appropriate simplifications can be selected for the geometallurgical optimisation.CITATION:van den Boogaart, K G, Tolosana Delgado, R, Mueller, U and Matos Camacho, S, 2016. How Details of the Geometallurgical Optimisation Influence Overall Value, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The occurence of high silver values in the oxidised zone of the main lode at Broken Hill is well known as a large factor in achieving the early fame of Broken Hill, and the minerals of this zone form a long list, which has been tabulated by G Smith*, and includes...

Jan 1, 1926