Search Documents

By K McSweeney, A Marton

This paper discusses the development of a strategy for ensuring long-term geotechnical stability of final pit walls at AngloGold AustraliaÆs Sunrise Dam Gold Mine. The strategy makes use of improved blasting techniques, changes to the mining sequence and other geotechnical techniques. Only the blasting techniques will be discussed in this paper. These were developed from numerous trials over a period of several months from May 2003 through to November 2003. The focus was to reduce crest loss damage and thereby improve final wall integrity, maintain designed safe berm widths, and ensure long-term stability. Crest loss mechanisms are now understood and are explained in this paper. The preferred solution is outlined; which is a combination of improved blasting and changes in the mining sequence to cater for pre-existing ground conditions. These ground conditions include dynamic hyper saline water with sometimes intersecting steeply dipping discrete structures. Project requirements were defined as mitigating or eliminating crest loss using 127 mm diameter pre-splitting and targeting minimal production blasting vibration levels against the walls. Blast results were measured by post blast visual inspections and video. Blast design input utilised the predictive algorithms built into simulation software when attempting to minimise vibration levels against the walls. Protection of the already fired pre-split line is now achieved using small charges against the wall and timing sequences which form a mask for the later firing main charges. The pre-split spacing is now modified to suit the geology. There eight blast domains identified around the perimeter of the pit, each having varying joint orientation. In addition, blasting the bench adjacent to the berm crest has particular considerations not required by the middle and lower benches. The preferred solution was to purposefully translate this damaged top section of the pre-split bench into a planned subsequent dig zone. The design of this top æweightÆ is a direct response to the nature of the crest loss mechanism.

Jan 1, 2004

By K Peters, C McKenzie

New Zealand has an established history of gold production beginning with the gold rushes of the 19th century in the Coromandel, Nelson/Marlborough, West Coast and Otago regions. Despite this, the number of significant modern hard rock gold operations has been limited in recent years due to a lack of sustained exploration capital and not limited geological prospectivity.The New Zealand Government is actively encouraging explorers to invest in New Zealand through a series of targeted promotional visits, more importantly through the acquisition of precompetitive regional geophysical data. Data collection has been completed over the prospective Northland epithermal district and a large portion of the South IslandÆs west coast that is prospective for both orogenic gold and intrusive related gold.Analysis of new data has been an important component in aiding the generation of exploration targets from prospectivity modelling. Determining the prospectivity of an area involves reviewing all the available data and analysing it with respect to the most up-to-date mineral system model for the mineralisation style of interest. Using the weights of evidence modelling approach, the most prospective areas for epithermal gold-silver, orogenic gold and intrusion-related gold have been identified. The key exploration parameters relevant to each mineral system are first represented spatially and then statistically combined into a single prospectivity map. New potentially economic deposits could be found by focusing exploration on targets identified from these models. The prospectivity modelling approach can greatly reduce the risk involved in mineral exploration.CITATION:Peters, K and McKenzie, C, 2013. New Zealand gold potential - using mineral prospectivity modelling to evaluate gold-bearing mineral systems in an underexplored country, in Proceedings World Gold 2013 , pp 479-486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Toro HCH, Von Borries GH

A brief description of the semi-autogenous grinding (SAG;) facilities of Compania Minera Disputada de Las Condes is given. A data-logging and computer system was connected to the plant inter facing the existing analog control system in a supervisory s, control philosophy. The development of a control straiov,v t,) maintain maximum power of the SAG mill atsubjected to process restrictions is shownThe present control scheme is discussed inalgorithm was designed based on correlations onLween vartaoles. Associated with this, a direct level of control was developed be, on classical control algorithms, process inter-active tuning has been included. Also, an algorithm to prevent overloading of the is discussed. Control scheme tests are presented in comparison t manual operator control under the same conditions. It is shown t the control strategy gives a more stable operation and a higher plant throughput.

Jan 1, 1985

By T Raynlyn, S Hapugoda, V Nunna

The predominant phase in most Marra Mamba, channel iron deposits and detrital iron ore deposits is goethite. Goethite abundant iron ore fines tend to have complex mineralogical associations and fine dissemination of gangue material. These ores are typically challenging to process using conventional beneficiation methods. With declining ore grades, there is a need to develop new processing routes for low-grade goethitic ores/fines.Comparative process amenability studies were carried out using two different processing options to recover iron with low alumina and silica content from a low-grade goethite-abundant iron ore fines (-2 mm) sample from the Pilbara region of Western Australia. The first option involved dehydroxylation at 350°C and 400°C, followed by grinding dehydroxylated samples to 100 per cent passing 106 µm and magnetic separation. The second option was processing raw sample by gravity separation using a Floatex density separator. The performances of the two processes are discussed in terms of the iron grade-recovery responses, and an optimal processing route is proposed based on the findings from these tests.CITATION:Nunna, V, Hapugoda, S and Raynlyn, T, 2015. Process amenability studies on goethite-abundant iron ore fines, in Proceedings Iron Ore 2015, pp 165–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By L Smith, R Beckie

Controls on environmental loading from acid rock drainage (ARD) are not well understood in waste rock material. In particular, relationships between subsurface flow and the timing, duration, and intensity of leaching of metals and acidity from waste rock dumps remain ill defined. This study investigates field-scale relationships between subsurface flow processes and geochemical processes in unsaturated waste rock. A 12-metre tall, unsaturated waste rock pile, constructed in 1994, was deconstructed and sampled at Key Lake, Saskatchewan, Canada, during the summer of 2000. A detailed sampling methodology was developed to characterise physical and chemical properties of waste rock material within the waste rock pile. Physical properties were characterised by measuring soil-water suction, volumetric water content, and grain-size distribution at 60 random locations within the pile and grain-size distribution at 20 grid locations within the pile. Attempts to develop a field-based soil water characteristic curve from physical field-data failed due to spatial variability and hysteresis of waste rock properties. As a result, grain-size distribution was used as a relative measure of subsurface flow. Paste pH, pore-water geochemistry, mineralogy, and water-soluble extraction results were used to characterise geochemical processes and sulfide oxidation at each of the 20 grid locations. Geochemical characterisation results demonstrated the preferential weathering of marcasite relative to pyrite and chalcopyrite. Dolomite was the main buffering carbonate mineral. Gyspum, jarosite and iron oxyhydroxides were the main secondary minerals. Pore-waters contained up to 800, 11.7, and 6 mMolar (78 000, 690, 1400 mg/L, respectively) of sulfate, nickel, and uranium, respectively, suggesting significant weathering has occurred. Measures of weathering indicators show no discernable correlation with grain-size distribution nor do they show any spatial relationship within the sampled grid. Reasons for this may include limited duration of waste rock exposure to weathering and development of fluid flow-paths, and limitations of characterisation methods used. Indeed, six years may not be long enough for weathering patterns to develop due to fluid flow-paths in this unsaturated waste rock pile.

Jan 1, 2003

By Massacci P

A review has been made of the studies focusing on methods for the description of grain -size distribution after breakage and, separa- tely, of the degree of liberation of the miner- al species making up the various grain-size classes of comminution products. The purpose of the study has been to de- velop an overall model of the phenomenon which, owing to the very effect of comminution, leads to the formation of grains that are generally of mixed composition. A calculation procedure has thus been de- veloped for the liberation function taken as the assessment of the distribution of mix com- ponents in the products obtained after a commi- nution process. The aim is to identify a func- tion which may, to a certain extent, simulate the variation of the grade-recovery function of an ore in relation to its degree of comminu- tion. The numerical model thus obtained has been tested out on results obtained experimentally.

Jan 1, 1986

The Hodgkinson goldfield contains over 50 separate lodes which have produced 9.7 tonnes of gold from ore averaging 37 g/t. The gold-quartz.lodes are spatially separate from tin and base metal mineralisation, associated with Permo-Carboniferous granitoids in the province. Host rocks consist of sub-greenschist metamorphic grade shale, conglomerate, sandstone, spilite, chert and melange. Oreshoots average 100 x 30 x I m in Size and are contained in cross-cutting quartz. filled with steep-dipping shear zones. Mineralisation in the quartz. consists of gold with minor arsenopyrite, pyrite, galena, and sphalerite with rare calcite. Scheelite and stibnite are aSSOCIated locally but are not necessary proximal or coeval. Alteration is restricted to centimetre-scale phyllic selvedges adjacent to the veins and veinlets.Most of the lodes and vems occur within six main 1.5 x 0.25 km mineralised areas whIch may indIcate separate areas of fluid flow and precipitation. Ore controls differ m melange- and sandstone-hosted lodes but several features are common to all the oreshOOlS. Most of the lodes occur within zones of duauon that are caused by splaymg, refraction through carbonaceous shale-sandstone contacts, or by rolls and changes in strike and dip.Lithologic contacts may act as areas of permeability and chemistry contrast which focus fluid and precipitation. Tensional veins are common between parallel shear zones and curved spur veins occur both in the hangingwall and footwall of the main fissure. Intersections and contacts may have enhanced local fluid flow in many of the areas.

Jan 1, 1991

By V S. Vutukuri, K Shariar

This paper present a modification of selected strength criteria for coal and rocks containing weakness planes. The three strength criteria, namely, Murrell (1965), Bieniawski (1974a, 1983) and Hoek and Brown (1980) have been assessed for coal (containing weakness planes) by using triaxial strength tests. Triaxial test results indicated that the strength of coal specimens depends on the weakness plane inclination with respect to the principal stress direction. However it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of coal specimens is reduced. The constant parameters in the three failure criteria for coal are determined for each weakness plane inclination by using the Datafit computer program (nonlinear regression analysis) and the results are compared with other rock types.

Jan 1, 1999

By J-P Franzidis, M Esvelt, E V. Manla

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant that is able to treat up to 2 tph solids. It consists of a bank of six 130 L WEMCO« SmartCells« and a bank of six 50 L WEMCO« SmartCells«. It was developed as part of the AMIRA P9 Project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. However, it may also be used to carry out pilot-scale flotation test work. This paper briefly describes the circuit modelling, simulation and scale-up test work performed using the FCTR and the use of the FCTR in pilot-plant test work performed by the metallurgical staff at WMCÆs Kambalda Nickel Operations and Mount Keith Nickel Operation. At both Kambalda and Mount Keith the FCTR was found to be very flexible and straightforward to run, with an easily changeable circuit configuration and stable operation. Testwork was facilitated through having full stream sampling on all streams, and a high degree of instrumentation providing accurate measurement of process variables. The results obtained from the FCTR testwork were highly repeatable. As a consequence of using the FCTR, WMCÆs Kambalda Operation and Mt Keith Operation were able to complete a rigorous programme of pilot plant testwork more quickly than in the past, and with a high degree of confidence in the results.

Jan 1, 2003

By A Patwardhan, M M. Alam, K K. Thatavar

A commercial wet scrubber was used in the SIU-Joy dust control laboratory to test several concepts for improving the dust control efficiency of a wet scrubber. The concepts tested included two filter-two-spray systems, hollow and full-cone sprays, horizontal and vertical sprays, different layer filters and addition of surfactant. The optimised scrubber configuration had water-only vertical sprays for pre-wetting coarse dust, and vertical surfactant-laden water sprays for wetting ultrafine particles. This scrubber configuration reduced dust concentrations from 250 mg/m3 to 1.8 mg/m3. In comparison, the conventional scrubber configuration in the feed provides an outlet dust concentration of 3 - 4 mg/m3 in field operation. Upon successful testing and optimisation of parameters in the laboratory, field demonstration of the concepts was conducted at an Illinois coal mine. The optimised scrubber configuration was tested in the field with good results in terms of improved visibility in the face area and reduced respirable and quartz dust concentrations. Additional modifications in the field involved relocation of the scrubber suction inlets from the bottom to the side and changing the water spray configuration on the miner head. These additional changes were based on a conceptualised spatial dust distribution profile in the face area. The results of these laboratory development and field demonstration studies are presented in this paper.

Jan 1, 2005

By K Hortin

Kidd Creek mine in north western Ontario is developing phase 1 of the deep mine project for mining between 2100 m and 3100 m below surface. Heat problems were experienced during the 2003 summer in working places about 2300 m below surface. At the time the mine had a æcold stopeÆ for cooling the air supplied to the mine below 1500 m from surface. The æcold stopeÆ is where during winter, ice is created in both the open pit and its connecting airways to the mine and used to cool air in summer. The operation and limitations of the existing cold stope were evaluated and led to the requirement for additional mechanical cooling to be available for the summer of 2004. The first stage of a surface refrigeration plant providing 7.5 MWR of cooling was approved, the compressor set was ordered in early January 2004 and the plant commissioned six months later in early July 2004. Based on the current modifications to the mining plan, further plant expansions are required in 2006 and 2009 leading to a total of 19 MWR of mechanical refrigeration and 8.5 MWR equivalent from the extended cold stope. The refrigeration system is described with emphasis on the specific adaptations necessary to suit Canadian conditions. Additional investigations were; using the refrigeration compressors in winter for heating and, extending the performance of either cold stopes or alternative ice storage systems. The winter use of refrigeration involve removing heat from the mine exhaust air to provide a cooling load and to use the hot water in the condensing circuit to heat the intake air and reduce reliance on mine air heating with natural gas. This paper follows on from an earlier one presented at the Seventh International Mine Ventilation Congress where the background and planning of the mine ventilation and cooling requirements were described for extending the mine at depth to 3100 m.

Jan 1, 2005

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By J Ferreira

To speed up multivariate geostatistical simulation it is common to transform the set of attributes into spatially uncorrelated factors that can be simulated independently. One decorrelation method is the method of minimum/maximum autocorrelation factors (MAF), where a two structure linear model of coregionalisation is assumed. The transformation decorrelates the theoretical model exactly, but the actual data are only approximately decorrelated. The MAF transformation can therefore be seen as a special case of a non-orthogonal approximate diagonaliser of a set of symmetric matrices. A more general approach for approximate joint diagonalisation (AJD) has been developed in the context of blind source separation. For these AJD algorithms no assumptions are made beyond symmetry of the individual matrices and so they can be applied to a family of experimental semivariogram matrices. In their application there are no restrictions on the number of structures in the linear model of coregionalisation (LMC) thus removing one of the conditions placed on the subsequent modelling of the spatial structure of the factors. In this paper the general background for the U-WEDGE AJD method is presented. It is shown that the U-WEDGE method achieves better spatial decorrelation than the MAF method. The factors derived from U-WEDGE are simulated using conditional turning bands simulation and then backtransformed to attribute space.

Sep 26, 2011

By L Hussey

Mt Keith concentrator treats low grade disseminated nickel sulfide ore supplied from the adjoining open pit mine. It is a traditional crushing, two-staged closed circuit grinding circuit (SAG & Ball Mills), followed by a complex split-size rougher, scavenger and cleaner flotation circuit. In 2016, 10.5 Mt was milled, at an average head grade of 0.54% Ni, yielding 35 000 nickel metal tonnes in concentrate.Historical analysis of the plant data indicated that of all the nickel lost in the fines rougher circuit tails stream, 25.6% was recoverable in an eight minute laboratory scale flotation test. These results implied that this fine nickel was readily available for recovery in the plant, either through operational improvements or additional flotation capacity. With operation optimisation ongoing, and capital within the business focused elsewhere, plant personnel were challenged to think differently about improving recovery.In 2012, a separate project to improve plant recovery when treating high talc ore was completed. Amongst other vessels, this project saw the installation of two 150 m3 Outotec Cells to the scavenger section of the fines rougher, middlings and scavengers (RMS 1) circuit. Since installation, the operation of these cells resulted in difficulties immediately upstream with instability in the scavenger cells. It was therefore decided that these cells would be better suited to treating the fines rougher circuit tails.The alterations required to divert these flows were minimal, with the capital project totalling $220 000.In the two years since installation, the fines rougher tailings nickel grade has dropped by 9.9%. The scavenger circuit has also seen a 2.8% reduction in tailings nickel grade, and instability issues were immediately resolved. This project serves as a lesson in how existing plant infrastructure may be better utilised to maximise recovery. Although this is especially applicable when capital constrained, such re-appropriation can be considered at any point to maximise return on existing assets. CITATION:Hussey, L, 2017. Repurposing flotation capacity at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 254–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By J Vann

Mineral Resource and Ore Reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential pitfalls are to be avoided, however, there are two other requirements which are of equal, if not greater, importance:good communication, and common sense. Estimation of Mineral Resources and particularly of Ore Reserves is almost always a team effort, involving a number of disciplines. Good teamwork requires good communication, both between team members and between the team and other parties having an interest in the process. Breakdown in these lines of communication can have far reaching effects on the project under consideration. The need to use common sense during a Resource or Reserve estimation exercise would seem to be self-evident. It is surprising, however, how often rigid adherence to procedures and methods prevails at the expense of clear thinking, usually with adverse and sometimes fatal effects on the project under consideration. This has become increasingly true as computerised methods have assumed a central role in Resource/Reserve estimation. The critical question that estimators should ask themselves at all stages of the process is: æIs what is being done sensible given the data available, what is known of this deposit and the purpose of the exercise?Æ

Jan 1, 1999

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

This paper puts the view that, for one gold deposit in Victoria at least, the Australasian Code for the Reporting of Identified Mineral Resources is severely deficient. The author questions whether or not the Code constrains the proper dissemination of information relevant to resource valuation. The author offers a view about the estimation of inferred resources, and provides data believed pertinent to the proper valuation of Ballarat Goldfields Ltd Ballarat East Project.

Jan 1, 1990

By Kelly D, Moore C

The Golden Mile, which has been mined continuously for the past 100 years by both underground and more recently open pit methods, occupies an area of 1.2 km by 4 km adjacent to the city of Kalgoorlie Boulder in Western Australia (Figure 1). Large-scale open pit mining at the Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operations is currently extracting 7.8 million tonnes of oxide and sulphide ore for a total production of 522 000 oz per annum. The effectiveness of grade estimation techniques at KCGM has been examined with reference to existing 10 m bench sample data from all operating areas within the Eastern Lode System of the Main and North pits. The aim of the study was to recommend practical parameters for grade control estimation. The review included comprehensive variography and comparison of nonparametric estimation methods (Joumel, 1983) such as indicator kriging and probability kriging with ordinary kriging, leading to the development of improved grade control parameters and procedures for both daily quality control and short term mine planning. This paper reviews the geological, statistical, geostatistical, mining and modelling features studied in order to present KCGM's Mining Department with recommendations for improving grade control.

Jan 1, 1994

By L C. P J Fonteneau, B Godel, E R. Ramanaidou

The Hamersley Province in Western Australia hosts large iron ore deposits. Each deposit displays various iron ore types that were defined on their metallurgical properties, especially in terms of porosity and mineralogy. Conventional porosity and mineralogy information on iron ore types are provided on 2D thin sections using automated image analysis with scanning electron microscopy (SEM)-based techniques combined with chemical analyses. However these techniques cannot accurately quantify the 3D porosity. High-resolution X-ray computed tomography (HRXCT) is a non-destructive technique providing a 3D image of the sample with a resolution close to 0.5 - 0.7 ¦m for samples size of up to few centimetres in length. 3D image analysis using customised algorithms now provide accurate quantitative porosity and mineralogy of iron ore types.CITATION:Fonteneau, L C P J, Godel, B and Ramanaidou, E R, 2013. Application of high-resolution x-ray computed tomography to iron ore characterisation, in Proceedings Iron Ore 2013 , pp 243-250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Stephenson D. B, Burgess J, Burgess F. L, Marshall S. H

A new high intensity flotation process 'FASTFLOT' is explained and its theoretical advantages compared with other flotation systems are discussed. The results of initial FASTFLOT testing on the zinc roughing circuit at Pasminco Mining, Broken Hill South concentrator are presented and compared to recent plant data. The comparison suggests that on roughing duties, the FASTFLOT process yields superior concentrate grade while requiring less than one third the residence time of a conventional mechanical cell plant. Strategies for FASTFLOT deployment are also presented.

Jan 1, 1994