Search Documents

By P Cleary, G K. Robinson, J Hilton, P Wilson

Concern has been expressed that Vezins can be biased when used for sampling fine materials if the cutter speed is as high as the 0.6 m/s which is often used. Using modelling techniques that consider airflow as well as particles, we have endeavoured to investigate sampling bias as a function of the size of fine particles, cutter aperture, cutter speed, shape of cutter blades, and the size of the gap between the inlet pipe and the cutter blades. Using crude estimates of the rate of airflow and a simple model of a single particle moving through air led to an approximate rule that bias will not occur due to mechanisms related to airflow for particles larger than about 200 microns; and bias will always occur for particles smaller than about 40 microns. For particles between these size limits, the extent of bias depends on particle density, cutter speed and cutter geometry as well as particle size.CITATION:Robinson, G K, Wilson, P, Hilton, J and Cleary, P, 2012. Avoiding bias when using vezins for sampling dusty materials, in Proceedings Sampling 2012 , pp 109-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Morrison AL

The volume changes occurring during the reduction by hydrogen of single, high-grade hematite pellets under isothermal and non- isothermal conditions were investigated using a time-lapse photographic technique. The major cause of swelling during iso- thermal reduction at temperatures in the range 600-1000¦C, was the disruptive stresses set up during the transformation of hematite to mag- netite. The severity of the disruption was temperature dependent; the degree of swelling increased with increases in the reduction temp erature. Under non-isothermal reduction conditions, in which the pellet temperatures were increased at constant heating rates over the temperature range 500-1000¦C, minor swelling (6-8%) occurred in the initial stages of reduction followed by pellet contractions of up to 15% in the final reduction stages. The low initial swelling and high final pellet shrinkages were due to a com- bination of the temperature dependence of the swelling mechanism, and the sintering of fine pores in the reduced iron in the latter stages of reduction at higher temperatures.

Jan 1, 1980

By J Player, R de Vries, E Villaescusa, H Saw, R Hassell

The use of cemented rock fill (CRF) for support of open stope walls has increased in the Australian underground mines operations over the last five years due in part to its low capital cost. In open stoping the exposed CRF masses require adequate strength and stiffness, in order to resist the forces and to limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or from development mining waste sometimes up to 1 m in diameter. However, the use of waste rock, which has a poorly graded particle size distribution may not achieve the required minimum target strength due to segregation and large air voids within the fill mass. This paper describes the optimisation of CRF strength by either crushing the waste rock or the addition of sand to the mix. Both methods increase the level of fines in the mix design. Cylindrical samples having 400 mm diameter and 800 mm heights were prepared for uniaxial compressive strength (UCS) testing. The UCS test was determined using the Western Australian School of Mines (WASM) large-scale static test frame. The laboratory results were compared with a database of large-scale CRF strength mixed without sand from a number of mine sites around Australia. The comparison shows a significant strength development in the CRF mixing with addition of sand for a given cement percentage. Due to the higher strengths achieved by the addition of sand and the crushing of the waste material these CRF types require less cement to achieve the same strength. This has the potential to improve the overall economics of open stope mining due to less dilution of the exposed fill mass.CITATION:Saw, H, de Vries, R, Player, J, Hassell, R and Villaescusa, E, 2017. Optimisation of cemented rock fill strength for open stope support, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By G K. N Subasinghe

Metallurgists operating Knelson Concentrators (KC) often rely on manufacturerÆs recommendations for selecting operating parameters, such as fluidising water flow rate and cycle time. Recent studies have shown that these parameters are not only dependent on the machine parameters but also on the feed characteristics, such as size distribution of the gold and gangue particles and the composition of its constituent minerals. It is known that a particle entering a KC initially traverses a circular path within the bowl. For a particle to maintain a given orbit, the required centripetal force must be supplied by external means. It has been argued that this centripetal force, which is dependent on the mass of the particle, its radial position and the rotational speed of the bowl, is provided by the fluid drag force created by inwardly moving fluidising water and the BagnoldÆs force created by the particle/particle collisions. Depending on the fluidising water flow rate, one of two situations can occur where the porosity of the bed increases or decreases, which influences the amount of material retained within the bowl. The amount of material of a given size and density retained in the bowl is thus dependent on the extent of the centripetal force provided. Based on the above concept, a criterion that can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It may also be construed that this criterion demarcates the transition of the bed from a packed-bed state to a fluidised state. By identifying the transition values for the different constituent mineral particles in the feed, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. In addition, the kinetics of gangue displacement by incoming heavy mineral particles were also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build-up of heavy mineral reaches a maximum. A model has been proposed to predict the optimal batch cycle time for a KC in terms of the feed characteristics and machine operating parameters.

Jan 1, 2006

By D Davis

The prediction of ground-borne noise levels from tunnel construction activities requires knowledge of the input vibration forces from the vibration source(s) into the cutting face, knowledge of the vibration transmissibility through the surrounding medium, and knowledge of the receiver building’s vibro-acoustic response. The conversion of this vibration energy into sound pressure within the receiver building depends upon the vibration coupling of the soil and the building’s foundations, the structure’s response including floor-to-floor attenuation and amplifi cation due to resonance, the radiation effi ciencies of the internal structural elements, and the room’s acoustical properties. Beginning with a known input vibration spectrum at the cutting face, it is possible to predict the resultant ground-borne noise levels within a receiver building using either analytical and/or empirical techniques, or by numerical modelling. This paper presents an overview of the various methods available to estimate ground-borne noise levels from tunnel construction activities and discusses the advantages and limitations of each.

Mar 8, 2011

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

By E R. Ramanaidou, M A. Wells

Reflectance spectroscopy is now an established technique for mineral exploration and ore characterisation. The efficacy of the technique as a tool to characterise the main iron ore and gangue mineralogy at African Minerals Ltd’s Simbili iron ore deposit in north-central Sierra Leone was tested through reflectance spectroscopic analysis of 13 000 pulped drill reserve samples using CSIRO’s HyLogger-1™ system. Specifically, integration of reflectance spectral data with more traditional methods of analysis, such as geochemical analysis and Satmagan measurements, characterised the mineralogy (ie hematite versus goethite) of the oxidised ore at Simbili, quantified the Al associated with goethite and hematite and evaluated the distribution of the main gangue minerals – kaolinite and gibbsite. Relative changes in the Fe2+/Fe3+-bearing oxide and silicate mineralogy, based on mineral indices derived from reflectance spectroscopic measurements, appeared well-related to changes in the ore profile mineralogy consistent with the main ore types identified at Simbili, as representative of an oxidised banded iron formation sequence. Spectral calibration models, developed from a well-characterised training set of mineral mixtures, representative of the oxidised ore zone mineralogy were used to quantify the distribution of Al associated with kaolinite and gibbsite and the iron oxides, goethite and hematite. Combining these mineral spectral parameters with compositional data enabled the differentiation of Al-substituted goethite and hematite and resulted in the identification of low Al-bearing, or ‘clean’, goethite and hematite from high Al-bearing, or ‘dirty’, goethite and hematite. Spectral quantification of the iron oxide Al composition provides a far more rapid means of quantifying the Al substitution in iron oxides at the deposit scale compared to traditional techniques such as X-ray diffraction analysis. It also enables a level of volumetric characterisation and the potential for large-scale (ie three-dimensional) mapping, which was not previously possible with other techniques. The potential of the technique was also highlighted when mapping the distribution of the main Al-bearing contaminants (gibbsite and kaolinite) identified in the oxidised ore zone at Simbili. Delineation of such zones provides a guide to managing the most appropriate processing options (ie upgrade potential) within a mineralogical framework. Three-dimensional modelling of the gangue phase distribution may also allow the mapping of lithological and/or structural controls that may be prevalent at Simbili. This work highlights the value in the application of HyLogging™ technology for rapid resource characterisation, particularly for volumetric identification and mapping the distribution of both the economic and gangue phases, which otherwise would be difficult to achieve. As such, the technique can provide a fast and inexpensive means to evaluate ore and gangue mineralogy at the deposit scale and provide a first-pass assessment of the mineralogy and compositional attributes, with the potential to better predict ore metallurgical properties.CITATION:Wells, M A and Ramanaidou, E R, 2015. Waste not, want not – delving deeper into the Simbili iron ore deposit using HyLogging™ scanning technology, in Proceedings Iron Ore 2015, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By P Christen

The Ernest Henry Copper gold mine situated in North West Queensland, Australia, is owned and operated by Xstrata Copper. Currently the open pit produces 11 Mtpa of ore. With open pit mining ceasing in mid 2011 development has begun on an underground sublevel cave mine to extend the life of the operation by another 12 years. When completed the open pit will be 530 m deep and 1.5 km in diameter. The orebody dips at approximately 45° and has been outlined a further 450 m below the base of the pit. This provides some challenges for the Ernest Henry underground mine which is designed to initially truck development and production ore from the end of the pit until a hoisting shaft is commissioned in 2013. Production will then increase to 5.0 Mtpa on its way to an ultimate rate of 6.0 Mtpa in 2016.This paper will focus on the capital development and infrastructure requirements for the underground mine. Areas covered include mine accesses, ore handling system, accommodations for the dip of the orebody, primary ventilation design, dewatering systems and selection of an underground workshop over surface only maintenance.Discussions include the complications arising due to the mine being located directly below a large open pit and the combination of first principle cost analysis and risk assessment which has been used to safely optimise the feasibility study designs.

Mar 21, 2011

By J Pearce, M Barteaux, S Pearce

The prediction of how waste materials will evolve geochemically within waste storage facilities has been the subject of hundreds of thousands of hours researched by geoscientists globally. Despite the quantity of research there are a number of significant areas of uncertainty that remain as partially resolved issues. One of the most significant issues is the applicability of scaling laboratory test results to field conditions, and the use of laboratory data for predictive calculations to determine geochemical evolution of waste materials in the field. This issue has arisen predominantly as a result of the relative paucity of field monitoring data from waste rock storage facilities (WRSFs) and the fact that laboratory test methods are not typically linked to specific field conditions; rather they are based on generic standardised methods and designed primarily to simulate accelerated weathering conditions that do not relate to field conditions in a linear manner.To address these specific issues the authors have in the last two years made significant progress in the development and deployment of advanced field monitoring equipment within numerous WRSFs. O’Kane Consultants (OKC) has previously reported the findings from data collected from these monitoring installations in a number of papers presented throughout 2013–2014. This valuable site data has subsequently been used by OKC as the basis to design and engineer advanced customisable site-specific kinetic leach columns at OKC’s geochemistry research laboratory. These columns represent an important advancement in kinetic column assessment methodology as they have been designed to replicate the field internal conditions within waste facilities.Key features of the columns include their capacity, size and technical specifications; including fully programmable solenoid-controlled air supply with variable flow and pressure control and in-line heating option, automated temperature control and monitoring, automated oxygen consumption and carbon dioxide production monitoring, and soil moisture/matric suction monitoring.This flexibility of the design not only allows for more accurate field-based assessment of pyrite oxidation rates (POR) but also assessment of the potential effectiveness of waste management options such as deposition within a reduced oxygen environment, for example, as simulations of reduced net percolation rates or oxygen ingress rates can be accommodated.CITATION:Pearce, S, Pearce, J and Barteaux, M, 2015. Advanced customisable leach columns – a new kinetic testing method to simulate site-specific conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Watson, A V. Engelbrecht, E Murray-Hayden

Whereas mine reconciliation is a well-established month-end process for most modern mining operations, the resource sector has yet to endorse uniform reporting factors against which model accuracy and metal recovery can be formally assessed. Logically, any comprehensive reconciliation framework should facilitate comparison between period reserve, mine and mill and production figures. Historically, Parker’s F Series ratios (Parker, 2012) are often used in some form by mine operators, although they are rarely shared externally, as formal definitions have yet to be accepted. This paper presents a structural extension to the reconciliation process, wherein resource ratios (R Series factors) are used to quantify the long-term impact of the information effect, together with dilution and ore loss. A case study from the El Limón Guajes (ELG) Mine Complex in Mexico is used to demonstrate how an R Factor Series can be implemented to facilitate operation optimisation, over and above conventional F Series reconciliation treatments. This approach is applicable to any mining operation.

Mar 22, 2022

By A Valero, G M. Mudd

There is active debate and research around the most suitable indicators to assess the sustainability of mining. The most common approach is to report a range of data for a given mine site (or less preferably, a company total), such as inputs, outputs, benefits and potential costs. The most popular protocol in use (and growing rapidly) is the Global Reporting Initiative (GRI). However, these measures are numerous and still do not allow a single over-arching indicator to be developed. Other measures, such as known mineral resources over time, do not account for critical challenges such as declining ore grades, increasing wastes and poorer quality ores or more difficult mineralogy. By adopting a thermodynamic approach to sustainability, through the concept of æexergyÆ, it is possible to incorporate into a single measure the effective quality of mineral resources. Exergy involves the assessment of the minimum energy costs involved in producing a mineral resource with a specific chemical composition and concentration from common materials in the environment. The exergy of a mineral resource is evaluated from mineralogic composition, concentration (or ore grade) and, of course, quantity, by multiplying the unit exergies with the tonnes of the resource produced (or consumed). Since exergy is a thermodynamic quantity (ie energy or joules), it is additive across different minerals, such as iron ore to gold to copper or even oil and gas or coal û making it an ideal indicator to assess mineral resource sustainability at the industry scale rather than the individual mine scale. This paper briefly outlines the theoretical basis for exergy, and then presents a range of commodity case studies showing the application of exergy to the Australian mining industry. Overall, the usefulness of exergy is clearly demonstrated for use as a broad indicator of the sustainability of mineral resources at the national or even global scale.

Jan 1, 2009

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Eupene GS, Cheong GE

Operations at the Mount Bonnie gold/silver project are described. The project is based on the gossan of a stratiform and stratabound polymetallic sulphide deposit. The gossan contains approx- imately 100 000 tonne of ore grading 8g/tonne Au and 230g/tonne Ag. This is mined in an open cut, and transported to a stockpile area lkm away, from which it is fed to the treat- ment plant. The ore is crushed through two stages and fed to a fine ore storage shed, from which it is reclaimed, milled and cyanide leached in draft tube agitators. The pulp is filtered using a horizontal belt filter to recover a pregnant solution. Silver sulphide is precipitated using sodium sulphide solution, and collected as a mixed sulphide/precoat concentrate on a drum filter. The solution is then passed through carbon columns where the gold is adsorbed and is subsequently recovered by methanol desorption using a process developed by Micron Research, and electrowinning. Modifications to the treatment plant circuit based on operational experience are Described.

Jan 1, 1984

Risk management has become an essential tool for mining companies to ensure their projects are well-managed and profit expectations are achieved. Risk management has also become a mandatory corporate governance requirement in Australia for publicly listed companies and equally important to attract investors. This paper provides a brief overview of the essential tools needed to implement a practical risk management framework to comply with the internationally recognised ISO 31000:2009 risk management-principles and guidelines from the perspective of small or soon to be producing mining companies. To?successfully?deal with the unknown and to manage the opportunities and risks involved with a mining project requires a clear understanding of the basic risk management principles. These include how to develop a project risk register, how to develop a project risk treatment plan and how to manage and monitor project risks to take full advantage of the opportunities presented.The first step is to identify and fully appreciate the risks that face a mining project. There are many risk identification methods that can be used including checklists, brainstorming and hazard and operability (HAZOP) studies. These often lead to a telephone book full of risks which are near to impossible to manage. A risk library specifically designed?for mining?projects containing no more than 100 risks will cover the major showstoppers, is practical and can be readily implemented and successfully managed.A risk framework also needs to be established which is compatible with the companyÆs structure and objectives. Once each risk has been assessed in regard to consequence and likelihood and the risk control systems are in place they need to be assigned to the responsible manager. The extreme or high risks will require a risk treatment plan to be developed. Risks will change during the life cycle of a mining project. Hence, a reliable monitoring system is also required for compliance.CITATION:Jones, J A, 2012. Mine project risk management, in Proceedings Project Evaluation 2012 , pp 117-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By S Gillies, H W. Wu

A study has been undertaken into mine ventilation systems currently in use within Australian modern coal longwall (LW) extraction mines. It reviews systems and discusses evolving changes being adopted to address the more complex challenges. There is a strong move to longer panels, wider faces, greater extraction heights, increased production rates, more efficient ventilation and decreased personnel. Each of these changes is motivated by improvement in productivity and generally leads to cost reduction. In addition, mine workings are moving deeper, which results in increased ventilation control issues such as higher total and respirable dust levels, greater seam gas contents in parallel with lower in situ permeabilities, spontaneous combustion and heat management issues. A comprehensive database of Australian LW ventilation practice is analysed. Currently there are a variety of LW panel ventilation circuits used in Australian underground coal mines due to various combinations of seam characteristics, gas emission rates, spontaneous combustion, geological features and surface constraints. The main issues usually addressed in the designing and planning of ventilation circuits for LW panels are airway velocity, gas concentrations, LW cutting methods (eg Bi-di, Uni-di or half web), ventilation of control devices, pressure differentials and leakage paths and understanding gas concentrations across the length and width of the goaf. If the ventilation circuit can manage the applied contaminant load (gases, heat and dust) at an acceptable cost and circuit duty, then supplementary controls, such as gas drainage, refrigeration and dust sprays and scrubbers, may not be required. CITATION:Gillies, S and Wu, H W, 2013. Review of Australian longwall panel ventilation practices, in Proceedings The Australian Mine Ventilation Conference , pp 87-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The industrial practice of separating finely' around valuable minerals from associ- ated gangue materials by froth flotation is well known. Despite the obvious importance of this industrial process, the predictive tools for plant engineering evaluation of flotation process variable changes are still in a developmental stage. Consider, for example, the situation where an operating engineer is faced with evaluating a change in an existing chemical reagent scheme, possibly based on batch laboratory data. When all is said and done, the engineer must still perform detailed physical testing of the proposed reagent change on the actual equipment in plant use to be confident even of the direc- tion of change of plant results, let alone the economic viability of the change. The theory behind chemical reagent behaviour in froth flotation has been studied extensively, e.g., (Aplan {1980}, Fuerstenau {1976}, Fuerstenau {1962}, and Somasundaran {1980}), and, certainly, important progress has been made. Unfortunately, the nature of the flotation process, with its complicated heterogeneous surface chemisty activity operating on highly variable and difficut to characterize ore surfaces, coupled with com- plex mass and momentum transfer phenomena, :;l riously compromises the plant scale predictive capability of theoretically based models.

Jan 1, 1978

By S France

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will comprise 2.5 km of ‘undrained’ driven tunnels and 900 m of drained cut-and-cover tunnel and portals.The project is aligned beneath a stream valley of Oakley Creek incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The hydrogeology of the area is complex with perched aquifers in compressible soils, cascading water levels in fractured rock aquifers, and discontinuous higher permeability units resulting in artesian water levels and groundwater springs.Numerical groundwater modelling was undertaken to assess the potential effects of tunnel construction and long-term operation on the groundwater system; the magnitude and extent of changes in groundwater level and the resulting potential for settlement, buoyancy effects, contaminant migration and adverse effects on creek base flow. Modelling also provides inputs to tunnel design such as groundwater seepage volumes and water pressures.The driven tunnel will be ‘undrained’ long-term so potential effects on the groundwater system are limited to short-term dewatering during construction. Significant project time and cost savings can be made if the portal areas are permanently ‘drained’, but this means potential effects are greatest in the long term condition.This paper summarises the investigations, implications of the complex hydrogeological setting on tunnel design and environmental assessments, and groundwater modelling undertaken during the planning stage of this project. The groundwater modelling has been used to incorporate mitigation options in tunnel design and construction sequencing; a comprehensive monitoring program will be used to trigger appropriate responses should effects differ from those predicted.

Mar 8, 2011

By P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mining and exploration properties have a unique set of technical risks. Privately-owned companies considering investing in the resources sector can optimise their investment decisions by adopting a systematic technical assessment of acquisition assets, similar to the approach commonly adopted by public financial institutions and publicly-listed companies.Technical due diligence provides a process to identify key geological, mining, geotechnical, metallurgical, environmental and social risks and opportunities and determine the most likely business case and valuation of assets. Technical due diligence is commonly carried out in parallel with legal, commercial and financial due diligence, often involving the acquirer, to maximise the understanding of the investment.There are significant advantages in investors conducting a comprehensive technical due diligence, which typically involves site visits and project assessment to international standards by an independent, multidisciplinary team of experts. The outcomes provide the opportunity for the investor to make early, informed decisions and to understand and manage risks.Technical due diligence may be carried out at several stages: when considering and weighing up a number of investment options, prior to and during a transaction or immediately post-transaction. In the first stage, the outcomes will inform the choice of investment and, more particularly, whether there are any fundamental flaws in the projects being considered. In the second stage, due diligence outcomes can inform the level of investment and approach to risk management and planning. In the third stage, risks and opportunities can be investigated in more detail, allowing the investor to consider the best options to reduce risk and maximise the benefit of the investment.This paper presents a summary of the technical due diligence assessment process, its benefits to investors, common risks in mining and exploration projects known to cause mining asset write-downs and principal technical due diligence approaches.CITATION:Keogh, A, Stoker, P and Thomas, M, 2015. Benefits of due diligence in private equity mining investments – maximising value and unearthing common risks , in Proceedings PACRIM 2015 Congress, pp 115–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M Morey

Ok Tedi Mine is located eighteen kilometers from the Irian Jaya border in the Star Mountains, Western Province, Papua New Guinea. Sequential flotation concentrators produce a copper / gold concentrate for market, and a pyrite concentrate for environmental containment, with low sulphur tailings from the pyrite flotation sequence being discharged to river. Strict sulphur assay targets are set for the riverine discharge. Current porphyry and skarn ore blends from open pit operations at Mt. Fubilan will cease by 2017. However, drill cores indicate an economic ore body in the skarn ores surrounding and below the current pit limits. With proposed mining from a western pit wall ‘cut back’ and an eastern pit wall underground operation, potential for ore ageing in sub level cave underground stockpiles is apparent. With little information in the literature, Ore Ageing test work at prefeasibility level consisted of multiple one tonne stockpiles of -50 mm crushed rock. For the bankable feasibility study, a successful test work program was implemented utilizing 40 tonne ROM ore stockpiles composed of exposed pit extensions of future ores. Realistic ageing profiles of Skarn ores were obtained from one tonne monthly samples subjected to laboratory testing. Test work outcomes included:• Similar ore ageing profiles from both the pre feasibility study (PFS) and feasibility study (FS) programs, suggesting ore susceptibility to oxidation has greater effect in ore ageing than rock size for Ok Tedi skarns. • Laboratory rougher flotation of pyrite showed significant variation in sulphur recovery rate, suggesting three classes of pyrite floatability.• Laboratory rougher flotation of both copper and pyrite for up to 19 months ore ageing from 11 stockpiles, suggested three stages in the ore ageing process.

Aug 8, 2011