Search Documents

By R. L. Grunes, F. K. Kies, C. D&apos, Antonio

THE several studies concerned with the annealing of thin nickel films have largely been restricted to films of a single thickness.1-4 It is well-known, however, that both physical and mechanical properties depend upon film thickness.5, 6 The strength-thickness relations found in vapor-deposited nickel films in the annealed and as-deposited states, as an example, are at least partially due to the density and arrangement of imperfections within the films.7, 8 For these reasons, the annealing characteristics of thin nickel films as a function of thickness were investigated. Electrical resistance was chosen to monitor annealing behavior since resistance changes are partially dependent upon defect structure. In addition, the equations predicting film resistivity as a function of thickness are already available.9, 10 Further advantages afforded by electrical-resistance measurements are its adaption to continuous readings during annealing and its relative simplicity. Nickel films were vapor-deposited, at average rates of 60Å per sec, on Vycor substrates held at room temperature in vacuums of about 10-5 torr. Afterwards, deposition-thickness measurements were made using a multiple-beam interferometric technique. A more detailed description of deposition procedures and the interferometer appear elsewhere.7, 8 The four-probe method was employed in measuring electrical resistance since this technique measures film resistance without contributions from lead wires and contacts. Resistance measurements were made before, during, and after annealing to temperatures of 700°C under vacuums of approximately 10-4 torr. Measurements were made every 25°C or more often when necessitated by unusual resistance changes. Cooling and heating rates were maintained at approximately 5°C per min. Typical resistivity vs temperature curves are shown in Figs. 1 through 4. It is apparent from these

Jan 1, 1965

By C. D. Haynes, S. C. Gambrell

The practice of roof bolting in WORLD-WIDE mining activities is very well-known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Various means of stress analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that can be easily analyzed. One of the indirect research methods is the photo-elastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various loading configurations.'-" In-Situ Mine Roof Trusses The photoelastic technique was employed here to evaluate the state of stress above a mine opening where support is provided by the in-situ mine roof truss. This support configuration, shown in Fig. 1, has gained popularity in recent years, particularly in mines with bad roof conditions." To the authors' knowledge, no scientific determination has been made of the advantages roof trusses may offer over conventional bolting configurations comparable to roof trusses. Ordinary mine roofs usually sag or bulge downward soon after mining. Normally, after some movement the roof begins to stabilize, but the face of this bulging mine rock is usually in tension and will almost always fail unless supported. Because rock fails easily in tension, it is desirable to "preload" the roof, that is, to impress a compressive force on the mine roof to prevent bulging and subsequent tensile failure. Ordinary rock bolting installations, particularly if the bolting is perpendicular to the mine roof plane, do not produce a preloading effect. Although bolting installations squeeze the strata together and produce a beam effect desirable for support, they do not have the advantage of actual uplift. They pull down at the anchorage point with a force equal to the bolt tension which sometimes causes a separation in the plane of the anchorage detrimental to roof strength. In-situ mine roof trusses require the installation of steel tension rods in the roof of the mine much the same as conventional roof bolts, except that the rods are arranged to produce a stress pattern above the upper surface of the opening similar to that of a prestressed beam. The roof rock acts to transmit the compression force. The simplest form of truss consists of two steel rods anchored to the back of holes drilled at an angle of approximately 45 over the mine pillars. These rods are collared near the middle of the room, and the lower ends of the rods are connected by tie rods and turn-buckles. Used in this manner, a small-diameter steel rod can provide essentially the same support as a wide-flange steel beam. By tightening the turnbuckles, an uplift on the roof can be produced. Objective of the Investigation The objective of this investigation was to determine qualitatively the state of stress that exists above a mine roof after the installation of the in-situ mine roof truss vs. that of two angle roof bolts, hereafter referred to as "roof bolts," drilled and placed in the same configuration, that is, 45" above each pillar and connected together in the middle of the room by a bearing member such as a steel beam. Each state of stress was to be identified, insofar as possible, as compression or tension above the mine opening. Model Construction A photoelastic model of a mine opening was coil-structed from -in. thick PLM-4B birefringent plastic and was machined to specification shown in Fig. 2. The dimensions of the opening were chosen to simulate a width-to-depth ratio of 3 to 1. Two % -in. holes were drilled at 45" angles, as shown, to provide for the loading devices. After construction, the model was annealed at 240°F to remove stresses produced during machining.

Jan 1, 1971

Jan 1, 1967

Rutile – Zircon Mining on East Coast Surfing Beaches – Rutile-Zirconium Producing Companies in Australia

Jan 10, 1964

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

Addicks, L Ambler, J O Anderson, F B Armstrong, T Allen, L M, Jr Arnold, C E Adams, C E Adams, R E Anderson, A J Booth, E L Bernhardt, D I Boyd, W S Browning, W C Blake, D E Black, T B Bergman, Julius Bowen, H P Beckett, P G Blickensdefer, F C Bond, Josiah Butler, P P Bondlas. Y

Jan 1, 1923

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By William E. Ford, Edward Salisbury Dana

Secondary Twinning. - When there is reason to believe that the twinning has been produced subsequently to the original formation of the crystal, or crystalline mass, as, for example, by pressure, it is said to be secondary. Thus the calcite grains of a crystalline limestone often show such secondary twinning lamella?. The same are occasionally observed (Ilc, 001) in pyroxene crystals. Further, the polysynthetic twinning of the triclinic feldspars is often secondary in origin. This subject is further discussed on a later page, where it is also explained that in certain cases twinning may be produced artificially in a crystal individual - e.g., in calcite (see Art. 282).

Jan 1, 1922

By A. Thielen

In experiments for the production of steel the principal problem has always been the introduction into, or removal from, the iron of a definite quantity of carbon. Although the solution of this problem had engaged a more or less blindly and empirically directed effort for a long time, it was only with the development of analytical chemistry that the rôle which carbon plays in the constitution of steel was disclosed in its full significance, and that many of the problems confronting the steel-maker were thereby more clearly defined than before. For a long time, and to a certain extent even to this day, the percentage of carbon in steel has been the controlling means of deter mining its quality and hardness. In many cases the percentage of carbon alone has been relied on for judging large consignments, such as the large deliveries of wire-billets and blooms to America during the past twenty years; and though to-day the influences of the other constituents are recognized and many other considerations are taken into account, and though, moreover, some special steels, such as the Hadfield manganese steel, apparently dispense to a certain extent with the assistance of the carbon, yet fix our Bessemer, Thomas, Siemens and crucible steel the carbon still remains one of the most important constituents, and I venture to say it is indispensable. In order to produce in the Bessemer converter a steel of a certain required percentage of carbon, two methods, as is well known, present themselves. By the one the decarburization process is stopped when the desired carbon limit in the bath has been reached ; by the other the bath is completely decarburizecl, and then a calculated amount of carbon added in the form of spiegel, ferro manganese, etc. In Germany the latter method only was adopted, and it was retained when the Thomas-Gilchrist process for the production of low-Phosphorus steel from high-phosphorus iron eame into use, since from the nature of the new process complete decarburization is neces-

Jan 1, 1891

By E. L. Affleck, W. G. Stevenson

In both Canada and the United States, a company making a public offering of securities must comply with regulations which have been passed by Federal, State and/or Provincial Legislatures. These regulations usually require the distribution of an acceptable prospectus which provides essential background information about the issuer, the project and the share offering. when the public offering has been accepted, the unlisted company may then seek a listing of its shares for trading on a Stock Exchange. Once listed, the company will be subject to rules of the Stock Exchange. This paper will deal with the specific information required for inclusion into a prospectus being submitted for a resource company and particularly those parts of concern to mining engineers and geologists.

Jan 1, 1985

CONTENTS PAGE FULTON, CHARLES H., and READ, J. BURNS-A New Roasting Furnace for Zinc Flotation Concentrate. Discussed by Charles H. Fulton, Arthur S. Dwight, B. M. O'Harra, Kurt Stock 1 STOCK, KURT.-Redistillation of Zinc. Discussed by G. E. Dalbey, Kurt Stock.. 3 BEASLEY, F. E.-High Zinc in Lead Blast-furnace Slags. Discussed by R. C. Canby, R. L. Lloyd, C. R. Haywood, G. E. Dalbey, A. S. Dwight, E. P. Mathewson, A. L. Walker, B. M. O'Harra, and C. P. Linville 4 STEELE, E. W.-Application of Pulverized Coal to Copper Refinery Furnaces. Discussed by F. R. Pyne, E. P. Mathewson 11 LINVILLE, C. P.-Recovery of Arsenic and Other Valuable Constituents from Speiss. Discussed by C. R. Hayward, C. P. Linville, G. E. Dalbey, A. S. Dwight, Edward F. Kern, Karl Eilers, E. P. Mathewson 12 A New Roasting Furnace for Zinc Flotation Concentrate Discussion of the paper of CHARLES H. FULTON and J. BURNS READ, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1362-D, with MINING AND METALLURGY,. October, 1924. G. E. DALBEY, East Berlin, Conn. What would be the, effect on the formation of sulfates of an increased water vapor content in the roasting gases? CHARLES H. FULTON.-I cannot answer that from our experience. The question of the formation of sulfate in the roasting of zinc is mainly one of temperature and the concentration of S02 and S03 in the gases. We found we could roast almost completely to sulfate if the concentration was kept at the proper point. We, however, did not care to do this because we wished to make a 5 to 6 per cent. S02 gas for sulfuric-acid work. The sulfating of the zinc oxide in the proper concentration of gases goes on very rapidly. There are certain places in the furnace system such as the Cottrell and in a part of the dust chamber in which the roasted

Jan 6, 1925

By G. Thodos, R. B. Grieves

A method has been developed for the accurate calculation of the cricondentberm and cricondenbar temperatures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain any number of components including paraffins and isoparaffins, olefins, acetylenes, naphthenes and aromatics. This approach is based upon the mole fraction of the low-boiling component in the mixture and graphically presents the ratios of the cricondentherm and cricondenbar temperatures to the pseudocritical temperature as {unctions of a boiling-point parameter. The only requirements are the critical temperature, normal boiling point and the approximate vapor pressure behavior of each component. For mixtures of more than two constituents a stepwise calculation procedure is necessary where the pseudocritical temperature is based upon the critical temperature of the pure low-boiling component and upon the actual cricondentherm or cricondenbar temperature of the mixture of all the remaining higher-boiling components. From an analysis of 22 binary systems (123 compositionsl, the average deviation of calculated cricondentherm temperatures from reported values is 0.87 per cent, based on degrees Rankine; and for 10 multicomponent mixtures containing from three to six components, the average deviation is 0.98 per cent. From an analysis of 18 binary systems (104 compositions) the average deviation of calculated cricondenbar temperatures from reported values is 0. 79 per cent; and for 15 multicomponent mixtures, 1.47 per cent. Equations, derived from the graphical relationships, are presented which enable rapid calculations for both binary and multicomponent systems. INTRODUCTION With the increasing tendency towards the use of high pressure processes, the need for an accurate method of calculation of the properties of a multicomponent hydrocarbon mixture in the critical region is becoming more essential. Critical region phase relations are also significant in gas condensate reservoirs, for which a knowledge of the fluid phase boundaries and regions of retrograde condensation make it possible to evaluate optimum operating conditions. The possibility of liquefaction in the underground structure may be established, and information on the feasibility of the use of repressurizing may be determined. A typical phase diagram for a multicomponent hydrocarbon mixture is presented as Fig. 1. This figure also shows the regions of retrograde behavior encountered by following lines AB and AC. If accurate methods of calculating the temperatures and pressures at the critical, cricondentherm (maximum temperature) and cricondenbar (maximum pressure) points of multicomponent hydrocarbon mixtures of known composition were available, it would be possible to estimate closely the entire phase diagram of any mixture. Several methods have been presented in the literature for the estimation of the critical temperatures and pressures of multicomponent mixtures containing all types of hydrocarbons and including the fixed gases.4-8,21 Considering the cricondentherm and cricondenbar points, the work is more limited. Etter and Kay5 have developed rather complex equations for

By H. Jehn

Like some other Pt-group metals palladium shows a low but considerable solid solubility of oxygen, which was found already from oxidation studies. The oxygen solid solubility of palladium in equilibrium with gaseous oxygen has been investigated at 900 - 1300 °C in oxygen (665 mbar) and air by gassing and analyzing polycrystalline samples. The 0-concentrations range from 40 to 90 ppm and decrease with rising temperature. The isobaric solubility can be represented by the least-squares fit log c0 = 0.5 log p02- 0.32 + 920/T (c0 in wt. ppm, p02 in mbar, T in K). The thermodynamic data of the exothermic solution reaction are calculated to ?H°= -17.6 kJ?mol-1 and ?S° -76.5 J?mol ? K-1. The behaviour of palladium in an oxygen atmosphere is characterized by the simultaneous reactions of the solution of oxygen in the metal and the formation and evaporation of volatile oxides besides the pure metal evaporation.

Jan 1, 1984

By F. A. Olson, S. L. Pohlman

A unique method of measuring weight loss as a function 3 of time, with a sensitivity of 10-5 grams, while leaching copper minerals with a flowing acid leach solution has been developed. Kinetic results obtained coupled with visual and microprobe analyses show topochemical reaction for the leaching of chrysocolla with sulfuric acid. The kinetics follow a shrinking core model and show ion diffusion through a product layer, chemical reaction at the unreacted core interface and mass transfer through the boundary layer as being important.

Jan 1, 1974

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.' These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe's compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967

[ ]

Jan 1, 1938

By G. Bhat, J. F. Libsch

A STUDY of the kinetics of embrittlement in engineering alloy steels during tempering has indicated that the presence of alloying elements may define two distinct regions of embrittlement: 1) at 800° to 1000 °F, termed low temperature embrittle-ment, and 2) in the temperature range 1150 ° to 1250°F, termed high temperature embrittlement.13 It has been suggested that embrittlement in each region may be due to a different mechanism. At intermediate temperatures and extended times the course of embrittlement may be influenced by the superposition of the embrittlement occurring in the two regions. Furthermore, low temperature embrittlement has been known to decrease as the temperature is raised slightly above the maximum embrittlement range.' Jaffe and BuffumV ave presented data for a Ni-Cr steel illustrating the removal of the em-brittlement occurring at 932°F by reheating to 1250°F for an hour. Their data further shows that embrittlement proceeds continuously with increased time at 1250°F, becoming pronounced at long times. They interpreted this behavior as a retrogression phenomenon involving the solution of the small nuclei of precipitate formed at 932°F as the temperature was increased, and reprecipitation of larger nuclei stable at 1250°F, with the reoccurrence of embrittlement. It appears desirable to reconsider this explanation in the light of the two regions of embrittlement proposed by the authors1 for some alloy steels. In addition, it appears desirable to determine any influence of a preconditioning treatment in each temperature range upon subsequent development of low and high temperature embrittlement. It is thus the object of this investigation to study the characteristics of the two modes of embrittlement proposed in a commercial Ni-Cr alloy steel (AISI 3140). Experimental Details Material—The material used in this investigation was commercial AISI 3140 steel bar stock, received as % in. hot-rolled rounds. The steel analysis was as follows (in percentages): C, 0.39; Mn, 0.79; Si, 0.30; S, 0.028; P, 0.015; Ni, 1.26; and Cr, 0.77. Material Processing and Heat Treatment—The bar stock was first ground to 0.430 in. squares and cut into specimens 23/4 in. long. These specimens were austenitized at 1650°F for 1 hr and oil

Jan 1, 1958

Jan 1, 1969

By L. B. Schmitt, N. H. Polakowski

Square bars of cold-dvawn copper, mild steel and a 2024 aluminum alloy were forced through an adjulstable gap between two hardened steel rollers by pulling or pushing. The rollers were either free to rotate or were locked in position so that conditions comparable with drawing, rolling, ad containerless extrusion could be created at will. Push or pull forces as well as roll separatirg forces were measured. Forming efficiency and coefficients of friction were determined. For- slow-rate deformation the values ot µ wrere between 0.09 and 0.14. Possibilities for further investigation are indicated. THIS work was undertaken with the aim of a) determining the principal parameters of cold drawing under simplified conditions directly, without recourse to speculative assumptions and b) comparing drawing with rolling and extrusion from the viewpoint of forces involved and deformation efficiency. Data of type a) relating forces in axially-symmet-rical drawing to die geometry. drafting schedules, material properties and lubrication conditions are abundant. Their intrinsic value is. however. limited as long as the radial die forces are unknown. On the other hand. the difficulties associated with measurement of these forces are serious as witnessed by the extreme paucity of such information."" Comparative investigations of type b) were also remarkably few and they all employed ring-shaped dies through which round bars were either drawn or pushed.2-4 Only in one case were the applied and the die splitting forces measured simultaneously.2 In order to simplify the problem, deformation under approximately biaxial conditions was adopted in the present work;. This enables both the drawing (rolling, extruding) efforts and the separating forces to be measured with reasonable ease by conventional methods. Since drawing, extrusion, and rolling can be carried out under virtually identical conditions only in a roller die. an adjustable tool of this type was constructed. The circular die profile involved a difficulty with interpreting the drawing and extrusion data. This was obviated by arbitrarily defining the angle between a contact chord and the drawing plane as the -.equivalent" die semiangle. The simplification was considered permissible since the effect of die angle was not specifically investigated. An additional conlplication was caused by the square cross section of the processed bars. This shape was selected as a compromise between the desire to have as massive as possible specimens and the capacity of the roller die. The metal was only partially restrained from spreading laterally. the flow conditions being therefore intermediate between plane stress and plane strain. On the Huber-Mises yield criterion the constrained and uni-axial yield strengths differ by up to 16 pct but the actual error due to the ignorance of the constraint factor was presumably much smaller than the maximum. In spite of these reservations it was felt that the method employed and results obtained have some merit. With certain further refinements to be indicated later, this technique can yield data perhaps more useful for checking metal forming theories than other, mostly indirect, methods. EXPERIMENTAL Materials—The metals used together with their principal mechanical properties are listed in Table I.

Jan 1, 1961