Search Documents

By M. A. Mayers, J. A. Thompson

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By J. A. Thompson, M. A. Mayers

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By S. S. Solomons, V. H. Tillmann, L. Smaniotto

INTRODUCTION The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) mines are situated at Broken Hill, New South Wales, Australia (refer Fig. 1). Both companies are wholly owned subsidiaries of Australian Mining and Smelting Limited (AM&S). Annual production from both mines is 2.3 million tonnes of lead, silver and zinc ore mined by a variety of underground methods. From 1911 to 1968, conventional overhand cut and fill stoping (both open and square set timber) was used almost exclusively, though some trials with shrinkage and sublevel stoping were undertaken. The trial stopes used short holes in conparison with today's sublevel open stopes. Mechanised cut and fill methods with regular rockbolt support were introduced in the early 1960's and undercut and fill stoping replaced square set timber stoping for pillar extraction in the late 1960's. Since 1968, increasing emphasis has been placed on longhole open stoping (LHOS) although some areas of the orebodies are comrnrnitted to the abovemehtioned methods since existing stope development makes it impracticable to change. In 1979, approximately half the total production was mined by LHDS and it is expected that the LHOS proportion will increase in the future. A vertical crater retreat method of longhole mining has also been successfully introduced to replace the undercut and fill stoping of some pillars and it is expected that this stoping method will be used in some future primary ore extraction. This paper reviews the progress of LHOS technology at ZC/NBHC with emphasis on the stope planning and design process and the importance of rock mechanics applications. The objective has been to maximise the primary extraction of the orebody giving due consideration to stability and safety. This has led to the design of a novel sloped wall longhole stoping method which should eliminate the formation of pillars by mining the orebody in a "continuous" manner incorporating a sloped sand interface between the blocks of ore being mined and the previously mined sandfilled stope. The expected results include the complete extract of the orebody without the formation of pillars and with minimal dilution of ore with sandfill. The evolution of the method can be best illustrated by following the mining progress of the relatively new Southern 'B1 Lode orebody at the NBHC mine. GEOLOGY Southern '8' Lode is the southern extension of the 'Bt Lode orebody, which is currently being mined further to the north in ZC/NBHC (refer Fig. 2). The ore block being developed and stoped extends for a vertical height of 90 metres from No. 17 level down to approximately ten metres above No. 19 level. The ore minerals are sphalerite and galena with the zinc:lead ratio averaging approximately 3:l with a minor amount of silver associated with the galena. There is a sharp contact between the ore and the country rock on the footwall and keel, while the hanging wall gradates into medium and low grade material. The gangue is primarily quartz together with garnet, biotite, feldspar, gahnite, sericite and minor apatite. In various horizons within the orebody, grey feldspar, quartz and garnet pegmatites occur as stratiform layers. The ore and country rock are competent with some inconpetent boundaries.

Jan 1, 1981

By N. S. Stoloff, M. Gensamer

Pyramidal (1122) slip was observed in cadmium single crystals deformed in compression and bending at room temperature and —196°C. Crystals tested in tension twinned with no evidence of pyramidal slip. A critical resolved shear stress law for the propagation of twin nuclei appears probable. Twinning and low-stress kinking are believed to inhibit the appearance of pyramidal slip under ordinary experimental conditions. SEVERAL reports of nonbasal slip in cadmium have appeared in the literature recently, two of the reports having appeared after work on this project was in progress. Brown1 reported cross slip on electron micrographs, but did not identify the cross-slip plane. Wernick and Thomas2 observed nonbasal slip traces parallel to [1123] on a crystal bent with a pair of tweezers, but this too was an isolated observation, with no confirmation of the glide plane. The critical stress for pyramidal glide, and the temperature and strain rate dependence of glide on this system were not discussed. price3 has reported some observations of nonbasal slip in thin films of cadmium with the aid of transmission electron microscopy, but a full publication of these observations was not available at this writing. Pyramidal (1122) <1123> slip also has been observed on zinc single crystals4, 5 and (1122) <1010> slip on magnesium single crystals,6 all oriented with the basal plane nearly parallel to the specimen axis. Since the choice of slip system in the hexa- gonal metals is generally believed to depend on the axial ratio, with basal slip predominating for high-axial ratios, the occurrence of pyramidal slip in zinc and cadmium is unexpected. The objectives of the present investigation were to confirm the existence of nonbasal slip in cadmium, to identify the slip system, and to obtain an estimate of the critical resolved shear stress, assuming that the resolved shear stress law is applicable. EXPERIMENTAL PROCEDURE Two purities of cadmium, 99.95 pet and 99.99+ pet, were employed. As received bars were cold swaged to 3/16 in. rounds. Bicrystals and tricrystals were prepared by passing the polycrystalline rods through a gradient without seeds. It was desired to obtain a large yield of single crystals oriented xo* < 5 deg, in order to be able to suppress basal slip during deformation by keeping the resolved shear stress on the basal plane to a minimum. Cylindrical single crystals of cadmium were prepared by a seeding technique developed by Weiner,7 to obtain a predetermined orientation. The single-crystal rods were sectioned to specimen size by an acid-cutting technique originally developed for zinc crystals.&apos; An aqueous solution of nitric acid was the cutting agent. The acid was picked up by a plexiglass disc spinning at an optimum cutting speed through the acid, which was contained in a sump-like arrangement. The section to be cut, the acid bath, and the spinning disc were enclosed in a plexiglass case. The rod to be sectioned was coated with a thick layer of collodion. At the points at which sectioning was to be effected, the collodion was removed over a length of about 1/8 in. by dissolving it in acetone. To prepare a surface suitable for microscopic exam-

Jan 1, 1962

By A. F. Meger

Coal treatment by oil spraying receives special attention at the Georgetown plant for the dividends it pays in satisfying present customers and attracting new markets. Customer satisfaction requires care, quality control, and use of suitable oils. REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal CO. who have helped develop, over a number of years, an efficient and flexible method for spraying controlled amounts of oil on coal. Since the Georgetown preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage. The graph, Fig. 1, shows results of the original tests made with a 700-sec residual blend and a 500-sec lubricating oil on Georgetown stoker coal of 1¼x3/8-in. size.* The advantages of better price, improperly blended can raise havoc. Some.,pale oils also, although odorless when delivered, give off a sweet sickening odor when atomized under pressure. It is recommended that all products be tested before they are used. There is a specific place for all spraying oils. For example, at a power plant a severe dust condition exists around the stockpile area and in parts of the plant. The cheapest spraying oil made, regardless of odor, will do an excellent job in this case and will save the company 3 to 5c per gal or more. Domestic trade, on the other hand, must be carefully handled to prevent complaints about odor, and the only way to do this is to stay with the proved products after the odor tests have been made. The preparation plant at Georgetown has facilities to handle either tank car or tank truck deliveries. Steam is available at the unloading point if the weather is severe, and there is an indicator at the unloading point to prevent overflowing the 20,000-gal underground storage tank. Systematic test samples are removed from each delivery and sent to the lubrication engineer to insure quality control. Fig. 3 illustrates the chutes in which smaller sizes of coal are treated. Fig. 4 shows the entire spraying system. Buried in the ground is a 20,000-gal tank with immersion heaters grouped around the feeder line to insure adequate gravity flow to the pump under all conditions of weather. Oil flows to a 500-gal preheating tank where the temperature is kept about 150°F by six 1½-kw immersion heaters thermostatically controlled. Hot oil is fed through a self-cleaning disc-type filter to the hydraulic pump. Valves and piping make it possible to transfer oil from one tank to another or to drain the lines for maintenance purposes. All this equipment is below ground level in a covered pump room,

Jan 1, 1955

By E. H. Edwards, J. Washburn

Zinc crystals were deformed in simple shear and it was found that anisotropic strain hardening occurred in which the inactive slip systems were hardened more than the active system. The formation of dislocation barriers by dislocation interaction was discussed as a possible explanation of the hardening of the latent systems. STRAIN hardening which accompanies slip in a metal crystal is not limited to the slip systems actively contributing to the plastic strain. There is also a strengthening of the latent slip systems which are crystallographically equivalent to the active system. In the case of aluminum deformed in tension, Taylor and Elam1 found that plastic flow on one set of octahedral planes caused either the same or a slightly greater hardening on an inactive set. Similar results have been obtained for crystals of a brass2 and of Cu-A1 solid solutions.3 Experiments by Rohm and Kochendorfer4 indicated that the hardening of the active system exceeded the hardening of any latent system for aluminum crystals deformed in shear. On the other hand, strain hardening in zinc and cadmium crystals tested in simple shear at —196°C was recently found to be greater in the latent than in the active slip direction." When the strain direction was shifted during testing to a direction 60" from the original, a higher stress was required for glide to continue than would have been needed for flow to proceed in the original direction. The relation between the hardening of active and latent systems must be complex, depending upon the relative orientations of the systems and upon the experimental techniques used to deform the crystal. A detailed knowledge of the hardening produced in latent systems would be valuable in choosing between possible dislocation models of the strain-hardening process. The experimental data now available are incomplete and even contradictory. The present study was undertaken to provide quantitative information regarding the relative amount of hardening of active and latent systems for a particularly simple case. Zinc crystals were deformed in simple shear along one of the three crystallographically equivalent directions [250], [1210], and [1120] in the slip plane, and the relative hardening produced in each of these directions was compared. Experimental Procedure and Results The single crystals of 99.99 pct purity zinc used in this investigation were grown from the melt in the form of 1 in. diam spheres. Shear specimens were acid-machined from the crystals by a method which has been described previously. The gage section of the test specimen was a cylinder having a height of 1/8 in. and a cross-sectional area of approximately 1/3 sq in. All specimens were machined with the axis of this cylindrical gage section aligned with the [0001] axis of the crystal. An innovation in the design of the shearing apparatus for these tests was the provision for a rapid shift in the direction of the applied stress from one slip direction to any other slip direction lying in the same slip plane. Fig. 1 shows a section through the specimen and shearing apparatus, and Fig. 2 is a

Jan 1, 1955

By P. Hudock

Thin films of PbS and CdS have been deposited on insulutiug- sapphire substrates by euzploying a subliwzation technique rising near-equilibriurum conditions in ultrahigh vacuum. Oriented polycrystalline PbS and CdS films on sapphire have mobilities approachitzg values characteristic of bulk crystals. In the case of CdS, special purification procedures were crucial in obtaining high-mobility films. By performing the depositiotz of a compound within a small chamber heated to a UNiform temperature within a Vacuum systerrz, it is possible to approach equiilibrium cod-tions r.~litl~irs the chamber. In this way; the sublimation and condensation proceed under near equilibrium co?zditions, and it was found that the properties of dePosited corrzpounds were similar to those of the source material. Oriented PbS films on sapphire have a roor?l- temperature unobility of 700 sq cm per v sec and a T-5/2 temperature dependence characteristic of bulk crrystnls. CdS layers on sapphive Izazse a resistivity ~uhich is corrlpamble to the resistivity of the souvce crystals over a range of four ordem of rrlagnitude. Irz contrast, Ihe resistivity of CdS films prepared by conventional evaporation depends largely upon the substrate terrzperat~ire and postheating treatrrletlt, vather than upon the properties of&apos; the solirce rrraterial. In the case oj the CdS films the achievment of high carrier mobility required the cargful exclusion of cont~~~~ii~unts from the films. The steps taken to accomplish this included presublimation of the source material, performance of the deposition at a backg-m~ozd pressure less than 10-8 Torr, and a solvent extraction with liquid cadminum, similar to that described by Aven and woodbury. The deposition of ,films under near-equilibrium conditions is being op-plied to other classes oj COmpounds. II should he of 1:allce ,tor llle deposition of nny matevial that decomposes in the vapor state. THIN films of PbS and CdS have been deposited on insulating sapphire substrates by employing a sublimation technique using near-equilibrium conditions in ultrahigh vacuum. Oriented polycrystalline PbS and CdS films on sapphire have Hall mobilities approaching values characteristic of bulk crystals. In the case of CdS, special purification procedures were crucial in obtaining high-mobility films. Depositions were performed in a small quartz sublimation cell shown in Fig. 1 that contained the compound and the single-crystal sapphire substrate. The substrates were etched in tapered solutions of hot phosphoric acid, rinsed in deionized water, dried, and transferred to the cell under dry nitrogen. Graphite crucibles and substrates were used in experiments where it was necessary to provide an inert test vehicle for the analytical determination of impurities in the source crystals and deposited films. The crucibles and substrates were machined out of spectrographic-grade graphite having less than 1 ppm of impurities. A quartz mask was sometimes used to define a pattern which could be used for Hall and resistivity measurements. Close spacing between the compound and substrate was maintained to insure better transport of each component from the source material.

Jan 1, 1968

By Arthur F. Taggart

RECENT jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out of the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely different ways, depending upon the relative sizes of the grains presented to it and those composing it. EXPERIMENTAL The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. C. Dorenfeld, a student in the Mining Department at Columbia. Spheres of different metallic alloys, Y8-in. diameter, were cast with a short piece of fine copper wire frozen in to serve for suspension. A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs. 2 and 3. DEFINITIONS The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a shorlrange product is one closely sized. A bed is loaded when operating with continuous feed

Jan 1, 1943

By D. J. Carney, J. Chipman, N. J. Grant

An absolute calibration has been achieved for sampling and analyzing liquid steel for hydrogen based on Sieverts&apos; values of hydrogen solubility in iron. Further checks were made in nickel, iron-nickel, and 18-8 stainless melts. The sampling method was successfully applied to a large number of commercial steel melts in various types of furnaces. The concurrent problem of sample storage was also solved. THE problem of sampling of liquid steel for hydrogen is more difficult than the problem of analysis. Hydrogen has a greater mobility than any other element; it is the only element that will diffuse out of steel at room temperature. In accordance with the known relation between temperature and diffusivity, the diffusion of hydrogen is extremely rapid at the temperature of liquid steel. Consequently, in the past, attempts to quench molten steel to retain the dissolved hydrogen have not been as successful as similar attempts with nitrogen or oxygen. The retention of hydrogen is especially difficult since it will continue to escape at room temperature even if the molten metal has been rapidly quenched. The hydrogen sampling methods may be classified broadly as (1) the rapid quenching techniques which attempt to preserve super saturation and (2) those methods which attempt to collect the gases evolved as the metal freezes and cools to room temperature. With all methods of sampling but especially with the rapid quenching methods, there is also a concurrent problem of storing the sample until analysis is undertaken. The two problems are interrelated and must be considered together when discussing liquid steel sampling techniques. The major obstacle in liquid steel sampling has been that there was no way of evaluating properly the various sampling and storage techniques which have been developed. It has not been possible to compare the accuracy of the various methods. For evaluation of sampling methods some known standard is required; this may be found in the published work on the equilibrium solubility of hydrogen in liquid iron which has been determined in three separate investigations.1,2,3 The data are shown in table I. Sieverts&apos; original method of obtaining gas solubilities involved measurement of the volume of gas required to saturate the liquid metal contained in an evacuated bulb of known volume. This procedure, improved by introduction of high frequency induction heating, has yielded reproducible results which appear to be entirely dependable. Using Sieverts&apos; method, it has been proved for iron and other metals and alloys that the hydrogen solubility is proportional to the square root of the pressure of the hydrogen gas above the liquid, so that one may work with various partial pressures of hydrogen to put different amounts of hydrogen in solution. From Sieverts&apos; law it is possible to know accurately what amount of hydrogen is dissolved in the liquid metal at the time of sampling. The accuracy of a sampling method may be gauged by reference to this known solubility. It was the purpose of this investigation to develop a method for sampling liquid steel and for storing the sample so that the analytical result would represent the actual hydrogen content of the metal bath. For this purpose an induction furnace was

Jan 1, 1951

By John B. Campbell, George G. Binder, Loren H. Jenks

Conventional methods of producing crude oil generally leave in the depleted reservoir 1 to 3 bbl of oil for every barrel brought to the surface. This paper describes a field test which explores the possibility of using gas-driven liquid propane to improve oil recovery efficiency. Laboratory theoretical and experimental studies leading to the field test indicated that low residual oil values could be obtained using limited amounts of propane driven by gas. The field test involved (I) repressuring the reservoir to the vapor pressure of liquid propane, (2) injecting the liquid propane, and (3) injecting dry natural gas to drive the propane and oil to the producing wells. Considerable preliminary work, including new drilling, work-overs, and a pressure survey was necessary. During the test, oil production rates have averaged about nine times the final primary rates. The field average GOR is still below the pre-test value. Oil recovery to date is 112,000 STB. About one-third of the 143,-000 bbl of propane injected has been produced to date. Results of the C-2 block test are encouraging and larger, more definitive field projects ore indicated. INTRODUCTION The cost of finding new crude oil reservoirs continues to increase. Today the oil industry is drilling more and deeper wells and making fewer big discoveries. Nevertheless, the demand for oil and oil products increases each year. It is natural that oil companies, faced with this situation, concentrate on recovering more of the oil existing in our known crude oil reservoirs. There is room for much improvement. For every barrel of oil brought to the surface by present day methods of producing crude oil, generally 1 to 3 bbl are left behind in the depleted reservoirs. The "unrecoverable" oil in petroleum reservoirs is largely "trapped" by capillarity. Since flushing with a solvent is exceedingly effective in combatting oil loss due to capillarity, much effort in this direction has been made in recent years1,2,3,4,5. Liquefied petroleum gas (LPG) has been suggested as a relatively inexpensive. abundant, easily recoverable solvent for crude. Some operators have observed striking responses in oil recovery at production wells offsetting input wells in LPG storage reservoirs6,7,8. In spite of the low unit cost of LPG, however, it is uneconomic in general to inject a volume of LPG into a reservoir to remove a like volume of oil. A modification of solvent flushing in which a limited quantity of liquid propane is gas driven through a reservoir appears capable of recovering much more than 1 bbl of oil per barrel of propane injected. Also, most of the propane injected should be recoverable for sale or re-use. Since such a process could well have widespread and profitable application, The Carter Oil Co. is making an extensive evaluation of the technique&apos;s possibilities. Laboratory development of the gas-driven propane recovery technique was sufficiently encouraging to justify testing in the field. Since 1952, the Production and Research Departments of The Carter Oil Co. have cooperated in a field test in the C-2 Block leases of the

Jan 1, 1958

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico&apos;s largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company&apos;s State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4&apos; gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico&apos;s largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company&apos;s State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4&apos; gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

In 1846 a bill was pending in Congress to reduce, or eliminate, the tariff on coal; the debate caused the same writer to visit the mines on the north side of the James River and to write a letter about them to the same paper.&apos; Omitting the political arguments, his account follows: "July 13, 1846. "Early in the morning we rose, washed, combed, and ate a first-rate breakfast, and then went to the Tuckahoe, mined by Messrs. Sneed and Dietrock. Coal was first discovered here sixty years ago, and mined by Colonel Thomas Randolph, the proprietor of the land. They were worked by him for his smith-shops. Since which time they have been worked periodically, up to the war of 1812, when they were abandoned; and recommenced in 1837 under the management of Dr. W. T.- Scott. Subsequently a Company was formed called Tuckahoe Coal Mining Company, which purchased the whole track at a cost of $30,000. They commenced the sinking of a shaft and went as far as 412 feet, and then pitched the fat all into the fire by hauling off altogether in despair. In 1843 Major Sneed went to work at it, and succeeded. I may here remark that Major Sneed has been the pioneer in this business on the North side of the River, and has sunk more shafts than any other man who has pursued this vocation in Eastern Virginia. The difficulties and expense in sinking these shafts are sometimes immense. The coal on the outcrop or surface is not always a guide to where it may be found imbedded many hundred feet under earth and rock. "The Tuckahoe Pits are on the Eastern end of the coal field, within twelve hundred yards of the Canal, and about twelve miles from Richmond. They employ fifty hands and raise some three hundred thousand bushels of coal per year. It is highly bituminous and excellent for the manufacture of iron. The Tredegar and Belle Isle Rolling Mills are supplied with it. It must be good and of the right kind&apos;, or they would not use it. These pits are the only. ones on this side troubled-with gas-of course ventillation is necessary. There is not as much water in this Pit as I have found generally in many others, although they have extended their operations to a considerable distance under ground. I have observed in examining the coal mines, that, where they are sunk over four or five hundred feet, they are annoyed by gas, and where there is a less depth they are troubled with water. It is evident, therefore, that water, in the region of these coal fields, does not run through the earth to any extent, even five hundred feet deep, and the farther you go below that the greater the increase of gas. "We next visited William Cottrell&apos;s Pits, situated one mile and a half north of this. He employs some thirty hands, and raises from 4 to 500 bushels per day. "T. & R. Crouch&apos;s Pits are one hundred yards north of Cottrell&apos;s. This firm employ from 80 to 90 hands, and raise from 8 to 900 bushels per day. They are now

Jan 1, 1942

By Regis M. N. Pelloux, N. J. Grant

Five or six alloys each in the systems Ni-C.v, Ni-Mo, and NL-W, spaced to cover the single phase areas as well as a part of the adjacent two-phase field, were prepared as uacuum-melted alloys. Tensile tests at room temperature and stress rupture tests at 1200° and 1500°F we.ve run for time periods to give fracture in 0.1 to 500 hr. Observations mere made of solid-solution and second-phase strengthening or uleakening, coupled with studies of ductility and the role of structure on the noted behavior patterns. THE development of stable creep-resistant alloys while broad and systematic is also highly empirical. A number of simple rules have been suggestedL-" but these are based on scant data. Whereas rules for low-temperature alloy strengthening can be applied with some success in more simple systems, the extension to behavior at high temperatures (greater than about 0.4 of the absolute melting temperature) is very poorly understood and has encountered important exceptions and deviations in terms of atom size or valency effects. In particular, the occurrence of both solid-solution weakening4,5 and second-phase weakening2 at high temperatures is of interest. MATERIALS AND PROCEDURE Nickel was chosen as the base material because of its important role in current high-temperature alloy applications, because of its freedom from a phase transformation, and because of wide solubilities for many elements of interest. The selected alloys were single- and two-phase structures in the Ni-Cr,6 Ni-Mo,7 and Ni-w 8 systems. The alloys were vacuum melted and cast, utilizing high-purity raw materials, in the form of 15 lb ingots. They were readily forged into 1/2-in. bar stock (except the two highest chromium alloys). The alloy compositions are shown in Table I. Typical impurity values are: Carbon: Max 0.03 pct (except for 30 and 35 pct Cr alloys which had 0.07) Nitrogen: Max 0.005 pct (except for two of the Cr alloys which had 0.05) Sulfur: Max 0.004 pct Silicon: Max 0.05 pct Each alloy was solution treated (air quenched) to produce comparable grain size. The two-phase alloys were then overaged in an effort to produce a stable structure for testing at 1200° and 1500°F, The results are summarized in Table 11. Following the heat treatments outlined in Table 11, the bars were machined to a gage section of 1.25-in. long by 0.250-in. diam. In addition to room-temperature tensile tests, stress-rupture tests were run at 1200" and 1500°F for time periods from 0.1 to about 500 hr. RESULTS Room-Temperature Mechanical Properties—The ultimate tensile strength, total elongation, and reduction of area values for all the alloys are plotted vs atomic percent of the solute element in Fig. 1. It can be seen that for the same amount of solute element the ultimate tensile strength increases in the order chromium, molybdenum, tungsten. Elongation increases (reduction of area decreases) with increasing amounts of solute for all the solid solution alloys, the values ranging from 50 to 70 pct. The ultimate tensile strength values for the two-

Jan 1, 1961

By J. P. Heller, H. B. Bradley, A. S. Odeh

It is an accepted procedure to represent oil field displacement problems in which the pressure is relatively constant by a potentiometric model. Variations in reservoir permeability thickness product are represented in the model by proportional variations in electrolyte depth. It is shown that significant errors are present wherever these variations are of such magnitude that the consequent differences in the electrolyte depth in the model or any regions therein are appreciable in comparison with their respective horizontal dimensions. To demonstrate the order of magnitude of this error, a hypothetical linear oil field in which permeability varies linearly with distance was treated both analytic.ally and by potentiometric model. The results obtained from the model are compared with the exact solution for various configurations of linear geometry. Deviations in flow times up to 11 per cent were observed. It is confirmed that these discrepancies can be reduced by increasing the areal scale and/or decreasing the vertical scale of the model. It is the purpose of this work to assist in the design of potentiometric models by indicating the relationship between this error and the chosen scale factors. INTRODUCTION The fundamental geometrical criterion which determines whether the pressure distribution in an oil or gas reservoir may be simulated in a conventional potentiometric model is the requirement that all reservoir parameters be constant along any vertical line between its upper and lower boundaries. This situation never obtains exactly; nevertheless, it is usually assumed that there is no permeability stratification within the section of interest, that all wells completely penetrate the sand, that there are no gravitational effects, and that variations in thickness of the sand are small compared to the horizontal extent of the field. In these ways the reservoir problem is reduced to two dimensions in which there is no variation of pressure in the vertical direction within the limits of the sand. Variations in sand thickness and/or horizontal pesmeability may be taken into account as described by Muskat, by considering the fluid conductivity of the reservoir in its horizontal plane to be proportional to the product of permeability and sand thickness. If the variations in sand thickness are small compared to the horizontal dimensions of the reservoir, then it is a good approximation to consider the reservoir problem to be essentially two dimensional. The same approximation, however, is made in the simulation of the assumed two-dimensional reservoir by the electrolytic model. The model, if it is to take into account variations of permeability-thickness product, must of necessity be made in three dimensions, that is, with variable depth. Most potentiometric model studies and theoretical treatments reported in the literature to date2,3,4,5,6,7,8 are those in which either an average permeability was used or a constant permeability was assumed. This is understandable since detailed permeability data are not usually available for the majority of reservoirs. Many investigators have recognized that the failure to incorporate permeability variations within a reservoir in model studies leads to serious error in predictions made

Jan 1, 1957

By S. F. Reiter, You-Chao Liu, W. R. Hibbard

Cyril Stanley Smith in his classic 1948 Institute of Metals Lecture&apos; noted in the case of annealing twins that: "It is well known that approximately the same number of twins per grain and the same general geometry are maintained in large grains as in small ones, a fact that certainly suggests a mechanism such as the above where boundaries and twins grow proportionately together. If this view is correct, a spherical grain should have no mechanism for keeping its twins." Such a constancy of twins per grain would be of particular interest as a tool for the study of the origin of annealing twins. It has been proposed by Mathewson2 and later by Barrett3 that in face-centered cubic metals slip occurs in the {111} Plane by <112> shears which combine in pairs to produce the macroscopically observed <110> movement. This proposal is schematically inviting since <112> slip permits the atoms of one plane to move along the interatomic valleys of its neighbor rather than up the hills across the atom sites. There is strong experimental evidence? that annealing twins result from the growth of nuclei in the form of "twin faults" produced by single <112> shears. It is possible that more twin faults would form at low deformation temperatures than at high ones, because the more rigid lattice may increase the tendency to "freeze" the twin faults and prevent their dissipation in slip. This is suggested by (1) the greater resistance to slip at low temperatures and (2) greater tendency toward mechanical type twinning at low temperatures (a summary of these factors is presented by Seigle and Brick5). These considerations would suggest the following: a. Constant twin/grain ratio for specimens deformed constant amounts at a constant temperature, but annealed at various temperatures above the recrystalliza-tion temperature. b. Larger twin/grain ratios for re-crystallized specimens previously deformed constant amounts at lower temperatures. The purpose of this investigation is to test these considerations. One half in. rods of phosphorous deoxidized electrolytic copper and 70-30 alpha brass (68.36 pct Cu, 0.005 pct Pb, 0.01 pct Fe, 31.62 pct Zn remainder) were rolled to a thickness of 0.350 in., milled to specimens 0.350 X 0.437 X 2 in., and annealed at 700°C to an average grain size of 0.065 and 0.090 mm, respectively. These specimens of each metal were then rolled 50 pct reduction in thickness and annealed one hour under conditions which were all combinations of the following: Rolling Annealing Temperatures. Temperatures. °C °C -70 400 25 500 200 600 Standard metallographic techniques&apos; were used to prepare specimens. By the method of lineal analysis7 using a minimum of ten samples of fifty grains each for each specimen, the ratios of twins* per total grains, twins per twinned grain, twin families* per total grains and twins per twin family were determined. Recrystallized grain size was determined by A.S.T.M. comparison methods.8 All observations were made on the rolling plane. The results are tabulated in Table 1.

Jan 1, 1950

By P. Marier, T. R. Ingraham

When anhydrous cupric sulfate is heated in a stream of nonreactive gas, cupric oxysulfate is formed. When this reaction is complete, the cupric oxysulfate then decomposes to cupric oxide, which is the normal end product of reaction. The kinetics of each of these reactions has been studied using pellets prepared from finely divided cupric sulfate and from finely divided cupric oxysulfate. In each case, the reactant-product interface within the pellet is well-defined, and by normalizing the decrease in inter facial area with the weight fraction of the pellet decomposed it has been shown that the interface migrates into the pellet at a uniform rate at constant temperature. The activation energy estirnated for the decomposition of cupric sulfate is 57 ± 7 kcal per mole and that for cupric oxysulfate is 67 ± 8 kcal per mole. The rate of interfacial reaction is flow-sensitive, increasing with increasing flow of a sweep gas in the range from 50 to 2000 cu cm per min. The rate of decomposition is retarded by sulphur trioxide in the sweep gas. The relationship between sulfur trioxide Partial pressure and rate is consistent with the Langmuir Adsorption Isotherm governing the retention of sulfur trioxide in the interfacial layer. MOST of the work reported on the thermal decomposition of cupric sulfate and of cupric oxysulfate is related to the thermodynamics of the individual decompositions.&apos;-4 No information is available on the rates of the individual reactions, on their activation energies, or on the effects of gas flow or of partial pressure of sulfur trioxide on the reaction rates. Some dubious conclusions based on relative reaction rates have been drawn from studies on the oxidation of sulfides. For example, on the basis of the products observed in a quenched system, it has been suggested5" that, when copper sulfide is roasted, the cupric oxide which is formed arises from the decomposition of either cupric sulfate or cupric oxysulfate. This is very difficult to reconcile with the thermodynamics of the C-S-O System,3 which support the probability that both cuprous oxide and cupric oxide precede cupric oxysulfate and cupric sulfate in the sequence of products formed during the oxidation of cuprous sulfide. In this paper the individual sulfate decomposition reactions will be examined and suggestions will be advanced for the mechanism of reaction. This will be based on the effects on reaction rate of changes in interfacial area, flow rate, and back-pressure of sulfur trioxide. EXPERIMENTAL Materials. The copper source material used in all experiments was Fisher Certified Reagent Grade anhydrous cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared by roasting cupric sulfate for 48 hr, with frequent rabbling, in an open tray in a muffle furnace maintained at 725°C. At this temperature, cupric sulfate develops about 0.16 atm pressure of combined sulfur trioxide, sulfur dioxide, and oxygen. Cupric oxysulfate develops only about 0.05 atm pressure, and is stable until

Jan 1, 1965

By John McGhee, Jack Newcombe, M. J. Rzasa

A series of water floods was made on laboratory prepared unconsoli-dated sand columns to study the effects on oil recovery of the solid-water-oil contact angle, the oil-water interfacial tension, flood rate, and oil viscosity. A procedure was developed for treating silica sand with silicone polymer to produce surfaces of varying degrees of wettability as evaluated by measuring the contact angle on a flat silica plate that had been simultaneously treated with the sand. Fluid interfacial tensions were changed by the use of surface active agents in the flood water. Water-wet, oil-wet, and intermediate wettability systems were studied at high and at low values of interfacial tension, at several flood rates, and with oils of different viscosities. For both oil-wet and water-wet systems and a low viscosity oil, recoveries were functions of the oil-water interfacial tension; also, increase in flood rate resulted in increased oil recoveries. High interfacial tension floods were more efi- cient than low interfacial tension floods on water-wet systems, while low interfacial tension floods were more eficient on oil-wet systems. Intermediate or neutral wettability systems were less sensitive to rate of flood advance and interfacial tension than either oil-wet or water-wet systems. The eflects of surface forces on oil recovery for high viscosity oils were not so well defined as for low viscosity oils. INTRODUCTION Reservoir rock surfaces vary in their wettability1, some being water-wet while others are apparently oil-wet. The factor of wettability enters into reservoir performance in both primary and secondary recovery, and into laboratory measurements of capillary pressure, connate water saturation, and relative permeabilities.&apos; In theory, the degree of wettability is measured by the contact angle for the system solid-water-oil. A water-wet system is defined as one in which the advancing water contact angle is less than 90". An oil-wet system is one in which the advancing water contact angle is greater than 90°.3 The surface forces in a solid-water-oil system are related by the Young-Dupree equation as follows4: These surface forces are commonly expressed as the difference in adhesion tension, or the product of the water-oil interfacial tension and the contact angle. If the contact angle is less than 90°, the adhesion tension difference is positive and oil displacement by water from a solid surface will be spontaneous and favored by a high oil-water interfacial tension. If the angle is greater than 90" the displacement will not be spontaneous but will require less energy the lower the oil-water interfacial tension. The contact angle and interfacial tension also appear in the capillary pressure equation5: PC = 2ocosejr .... (2) The quantity cos was used by Rapoport and Leas6 s a factor in the generalized form of their "sealing coefficient." Warren and Cal-houn&apos; presented the results of cos on oil recovery in oil-wet systems and correlated their data using a "scaling coefficient" suggested by Jones-Parra and Calhoun.8 The "sealing coefficients" were advanced to help correlate the effects of the variables influencing oil recovery by

Jan 1, 1956

By D. C. Jones

THE term "coal-mine mechanization" is definable in several ways. In its general application it can mean the use of machines instead of manpower in each of the various mining activities necessary for the produc¬tion of coal-so that under this definition a mine that uses mechanical coal cutters could be classed as a mechanized mine. Common usage, however, insists that a mechanized mine is one in which machines are used for the entire process of mining or extraction and transportation of the coal. For the purpose of this paper, then, the second definition of "coal-mine mecha¬nization" will be used, and practices employed in mines where the greater part of the production is obtained through the use of mechanical loaders and conveyors will form the basis for this discussion. PHYSICAL CONTACT HAZARDS If we were to group all the hazards that accompany the use of mechanized equipment in a mine, the predominant class would be that which, for want of a better name, might be termed the "physical contact" hazards; that is, all the sources of danger that lead to accidents through physical contact of workmen with ma¬chines. A survey of accidents in a group of mechanized mines indicated that this class of hazards may be responsible for more than half the number of accidents in mechanized mining. For example, of 21 mining-machine accidents at one mine, 14 were of the physical contact type of 14 loading-machine accidents at the same mine, 8 were the result of physical contact. Certain of these hazards an controllable through the use of guards-¬a guard over the cutting-machine bits whet the machine is being trammed from place to place, or a chain or some similar locking device around the cutter chain, so that an accidental blow or push against the bit control will not cause the cutter chair to move. Other hazards, such as the possibility of. a loader operator having hi foot crushed by a crawler tread, or , brakeman being hit by a loader boon swung too far to one side while a car is being loaded, might be subject to control through the use of guard devices, but the reduction or elimination of all physical contact hazards by such methods doe: not appear feasible. Every accident of the physical contact type should be investigated to discover whether guards could have prevented it, but often the only way in which to combat these hazards will be through the awakened consciousness of each workman as to the danger that exists if he indulges in unsafe practices. A good approach to control of accident: in any mine is the establishment of a set o: safety rules or operating rules. The intent of such rules is to provide guides for the workmen to follow in the operation of equipment. Frequently the workmen have no regard for such rules, and observance is obtained only through compulsion or the part of management. An interesting development in connection with the formation of safety rules occurred during a training program for employees in the

Jan 1, 1946

By J. W. Hickman

INTRODUCTION RECENT work by the authors1 on the oxide films formed on alloys of titanium and zirconium with nickel and copper indicated that an investigation of the oxides which form on alloys of copper and nickel might permit the relative rates of formation and diffusion of the ions of. these metals to be determined. This binary system is of further interest since the alloys which form are of the solid solution-type over-the entire range. In addition nickel is much more oxidation resistant than copper. A comparison of the free energies of formation of the simple oxides which may occur on these alloys indicates that nickel oxide should be observed over the entire time and temperature ranges of oxidation for all alloy compositions.1 In. order for nickel oxide to predominate on the surface, it is necessary that nickel ions form and diffuse to the surface. Two factors which may influence the formation of nickel oxide may be the ionic sizes, where Cu+ is 0.96Å and Ni-++ is 0.70Å, and the charges on the ions. On the basis of size, Ni++ should diffuse more readily than Cu+ while on the basis of charge, Cu+ should form more readily than Ni++. According to Uhlig2 passivity to corrosion in an alloy appears at a critical composition which for copper-nickel alloys is related to the tendency of the d band of electronic energy states to fill with electrons. This composition in the copper-nickel alloys corresponds to 40 at. Pct nickel at which composition Uhlig2 (quoting La Que&apos;s data) states that the alloy system becomes passive. Magnetic and specific heat data indicate that the d band of copper-nickel alloys is filled at 6o at. pct copper or 4o at. pct nickel. Mott and Jones3 have shown that if, on alloying nickel with copper, one considers a copper atom to be identical with a nickel atom except for an extra electron (nickel -has the-configuration: 3d8 4s2 and copper: 3 d10 4s) then at 60 at. pct copper or 4o at. pct nickel enough electrons are contributed by copper to fill the d band of the alloy. At this composition the magnetic susceptibility approximates zero according to Grew.4 Although the electron diffraction data will not determine the rates of the several reactions which may occur during oxidation, yet a determination of the structures of the surface oxides may yield information concerning the relationships, if any, which may&apos; exist between the oxide structures which form and that composition where the magnetic susceptibility approximates zero. It is quite possible, of course, that the mechanisms of the oxidation and corrosion reactions may be so widely different that no correlations between them may be possible. SURVEY OF LITERATURE The metals, copper and nickel, which are face-centered cubic, form solid solution alloys which are face-centered cubic with no superstructure for all compositions. Three oxides of nickel have been investigated structurally by X ray diffraction. Of

Jan 1, 1948