Search Documents

By P. A. Tucker, C. R. Hudgens, D. E. Etter, D. L. Roesch, D. B. Martin

The equilibrium phase diagram of the Pu-Cd system is presented based on data obtained by differential thermal analysis, metallography, and electron-microprobe X-ray analysis. Liquidus temperatures range from 320° to 934°C. The system contains one congruently melting compound, PuCd, (945°C), and three incongruently melting compounds, PuCd, (800°C), PuCd, (730°C), and PuCd11 (410°C). A liquid-miscibility gap extends from 2 to 60 at. pet Cd with the monotectic reaction isotherm at 910°C. INTEREST in the potential use of plutonium alloys as reactor-fuel materials has prompted investigation of the phase equilibria in plutonium binary systems. A cursory investigation of the phase equilibria in the Pu-Cd binary system was conducted by differential thermal analysis (DTA), metallography, and electron-microprobe X-ray analysis (EMX). Extensive solid solubility of cadmium in both e and 6 plutonium was predicted1 based on atomic radii and electronegativities. Liquid immiscibility between these two elements was also predicted based on Mott's extension of Hildebrand's method. In the only previous investigation of the Pu-Cd system,2 two intermetallic compounds, PuCd11 (incon-gruent melting point 406°C) and PuCd8, were identified. EXPERIMENTAL The plutonium metal used in this work had a total impurity content of 500 ppm; the major impurities were: carbon (215 pprn), silicon (75 ppm), iron (60 ppm), nickel (40 ppm), and aluminum (25 ppm). The cadmium was reagent grade with a purity of 99.99 pet. The DTA technique for the study of plutonium alloys was previously described in detail.3 The alloys to be studied were prepared in tantalum DTA specimen capsules which were sealed by inert-gas welding. The alloys were homogenized in the liquid state in these sealed capsules which prevented the loss of cadmium by vaporization. Only the thermal arrests in the DTA heating curves were used to define the transformation temperatures of the system since supercooling affected many of the results during cooling. After the alloys were analyzed by DTA, the same alloys were used for the metallographic studies. Metallographic examinations were conducted in the manner described for plutonium alloys., No reaction was detected between the alloys and the tantalum capsules. Alloys for EMX analysis were placed in metallographic mounts together with specimens of unalloyed plutonium and cadmium which served as standards. The samples were highly polished but unetched. No protective coatings were applied to the surfaces of these radioactive specimens. Such coatings are detrimental to the excitation conditions and have been found to be unnecessary for the control of radioactive contamination. RESULTS The results of the DTA studies are presented in Table I. The phase diagram, constructed from these data plus the metallographic and EMX results, is presented in Fig. 1. The congruently melting compound, PuCd2, was identified by the occurrence of a maximum melting point (945°C) at 33.3 at. pet Pu-66.7 at. pet Cd and by the presence of a single phase in this composition.

Jan 1, 1965

By M. E. Wadsworth, R. C. Peterson, W. M. Fassell

The temperature and pressure dependence of the reaction of tantalum in oxygen were investigated from 500° to 1000°C at pressures from 10 mm Hg to 600 psi total oxygen pressure. Tantalum was found to oxidize linearly under the above conditions. Three distinct regions of temperature dependence were found with different energies of activation. From 500° to 600°C the rate of oxidation of tantalum was found to be essentially independent of the oxygen pressure at the pressure investigated. The oxidation rate increases rapidly with an increase in pressure from 600' to 800°C. The dependence of the oxidation rate on the bulk concentration may be expressed by V = k'?, where k' is the specific rate constant and ?=k1Co2/(l + K1Co2), where k, is the equilibrium constant for the adsorption of oxygen on tantalum. ONLY a limited amount of data has been presented in the literature on the oxidation behavior of tantalum metal. Some values of its oxidation rate were reported in the Corroston Handbook' and by McAdams and Geil.' The first extensive investigation of tantalum was the work of Gulbransen and Andrews." They determined the reaction rates of tantalum in O2 and N2. Their results indicate that this metal follows the parabolic law in the temperature range of 250" to 450°C in O2 at pressures of 7.6 cm Hg with an activation energy of 27,400 cal per mol. In nitrogen, the metal follows the parabolic law from 500" to 800°C at 7.6 cm pressure. All experimental determinations were of 2 hr or less duration and deviations from the parabolic rate conceivably could occur at longer times. A spectrophotometric study of the oxidation of tantalum by Waber, Sturdy, Wise, and Tipton' indicated good agreement between this method and the microbalance technique. The experiments were conducted in air from 220" to 350°C. The metal was found to follow the logarithmic law up to 320°C and the parabolic law at higher temperatures. The activation energies in the logarithmic region were reported as 12.57 kcal per mol and 12.0 kcal per mol, respectively, for the microgravimetric and spectrophotometric methods. In the parabolic region the activation energy was found to be 27.2 kcal per mol, in good agreement with the value of Gulbransen and Andrews." The present paper is concerned with the behavior of tantalum from 500" to 1000°C in oxygen at pressures ranging from 1/2 to 40.8 atm pressure. Earlier preliminary data by McKewan5,6 indicated the following facts concerning the behavior of tantalum: 1—At temperatures from 500" to 600°C, the metal followed the linear law. 2—At 575°C the rate of oxidation was found to increase with O2 pressure. 3—The Arrhenius plot in this temperature region was nonlinear. The nonlinearity of the Arrhenius plot was indicative of a more complex behavior than originally suspected for this metal.

Jan 1, 1955

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated mineral-spyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying 1 per cent is considered good grade; 0.7 to o.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent WO3 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 6o to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By W. I. Duvall, D. E. Stephenson

A theoretical solution is given for the energy that is radiated outward when either a cylindrical or spherical cavity located underground in a uniform stress field is suddenly created or enlarged. The method of derivation shows that the stress field in the solid rock surrounding the opening does work on the rock because of elastic displacements that result when the size of the cavity is increased. The amount of this work is sufficient to account for both the increase in the strain energy in the rock surrounding the opening and the seismic energy that radiates outward. Thus, the source of the radiant seismic energy is mainly the gravitational potential energy and not the strain energy stored in the rock. The amount of the radiant seismic energy is directly proportional to the volume of the rock removed from the opening or relieved of stress. Seismic energies from rockbursts are compared with earthquake energies. Also, the amount of gravitational potential energy released by underground explosions is calculated and found to be small compared to the seismic energy generated by the detonation of the explosive. A review of the early literature on rockbursts shows that a number of investigators calculated the amount of energy released by rockbursts. 1-5 However, none of these papers give the formula used to make these calculations or a reference to the derivation of any formulas. The general impression that one obtains from these early papers is that the main source of the seismic energy released by rock-burst is the strain energy stored in the rock before it is fractured. However, a few of the early papers appear to have considered the solid rock at a distance from the mine opening as a possible source of the seismic energy. Recently Black and starfield7 gave a theoretical solution for the strain energy in a stressed plate with and without a circular hole. Also, Press and Archambeau8 gave the theoretical solution for the seismic energy released when a spherical cavity is created in rock subjected to a three-dimensional stress field. Both of the above theoretical papers start with the condition of no opening and calculate the strain energy before and after the opening is suddenly formed. Neither of these papers appear to have calculated the work done by the applied stress field as the cavity is enlarged. The rockburst problem associated with deep mining is concerned with the failure of the solid rock surrounding an underground opening. Therefore, it seems appropriate to consider theoretically the problem of suddenly enlarging the size of an existing opening. The purpose of this paper is to present the theoretical solution for the energy that is available for release as seismic energy when an underground circular tunnel or spherical cavity is suddenly enlarged in diameter. To keep the mathematics as simple as possible, a uniform radial applied stress field is assumed and the rock is assumed to be isotropic, homogeneous and perfectly elastic.

Jan 1, 1965

By David L. Sikarskie

The measurement of residual stress fields using X-ray diffraction techniques requires the removal of successive layers of material from the specimen. In the process of removing these layers, the underlying residual stress field is altered; hence, if the original stress field is desired, corrections must be made to the measured stresses. Although these corrections already exist for a number of cases, an alternate procedure is outlined herein whereby the corrections are presented in series form. This form is numerically more convenient within certain ranges of correction depths and in its simplicity gives additional insight into the factors affecting the corrections. It, further, readily permits determining the proper slice depth to remove and the effect on the correction of both specimen thickness and magnitude and form of the measured residual stress itself. ONE of the techniques currently being used to determine residual stress fields is X-ray diffraction. Since X-rays are diffracted essentially from the layers of atoms near the surface of the specimen, of the order of 0.0001 to 0.001 in. depending on conditions, the method can only determine stresses* in this very thin surface region. Therefore, if the residual stress field at some depth into the specimen is required it is necessary to remove successive layers of material taking measurements after each cut. In the process of removing a thin surface layer of stressed material, however, the over-all equilibrium of a cross section of the specimen is disturbed with the result that the internal residual stress which existed before the slice of material was removed is altered. This alteration of stress occurs after each slice and its effect is cumulative. Thus, if the original stress distribution is desired, corrections must be applied to the measured stresses. These corrections can be found by satisfying equilibrium on each new cross section. These corrections have been derived in detail for a number of cases, e.g., cylinders, bars, plates,' and also are given in Appendix VI of Ref. 2. In each of the above cases the correction terms require the evaluation of definite integrals of the measured residual stress distribution. In general, this is indeed the way one would proceed with the corrections. There are a number of instances, however, where the integrals can be replaced by a series form of correction which is considerably more convenient numerically and, also, gives added insight into the factors which influence the corrections. Such a form of the correction is particularly useful, for example, if one is interested in designing a test such that stress corrections will be small. Also, the question of what depth of slice to use in relation to both specimen thickness and residual stress distribution itself must invariably be answered. Questions of this type can be readily answered using a series form of correction. In addition, if the correct residual stress distribution is needed only for limited depths into the specimen the series correction provides numerical results which are equivalent to the integral correction. I) DERIVATION OF THE SERIES CORRECTION The problem to be considered here is that of a bar or plate,* i.e., either one or two dimensions of the specimen is large compared with the third. Also, the residual stress distributions considered depend only on z, see Fig. 1. In view of this it can be shown' that a stress correction, based on simple beam theory, satisfies all conditions of "elasticity theory" and hence is the correct (and only) solution. The integral form of the correction (this assumes that the measured residual stress is a piecewise continuous function) as given in Ref. 1 is:

Jan 1, 1968

By B. Ancker, E. R. Parker

The small-angle dislocation-boundary density of nickel and some of its alloys was investigated as a function of strength. It was found that the strength is a linear function of the density for pure nickel and for Ni-Ti alloys, but not for Ni-Co alloys. The results are interpreted in terms of dislocation theory. THE processes by which metals deform are still poorly understood, even though there has been a concentrated research effort in this field during the past fifteen years. Single crystals and individual grains in polycrystalline aggregates often develop a subgrain structure when deformed. Substructure formation occurs as a result of local plastic bending and its development is augmented by annealing at moderate temperatures.' Investigations made to date, largely qualitative in nature, have shown that the substructure is composed of a network of small-angle boundaries. The purpose of the present paper is to present some quantitative data on substructure (obtained by X-ray techniques) and to correlate the results with the strength of the metal in which the substructure existed. Nickel and some of its alloys were used for the experiments. The presence of certain kinds of foreign atoms greatly alters the formation and effect of the substructure. Polycrystalline tensile specimens were prepared from high purity nickel, two Ni-Ti alloys, and two Ni-Co alloys; the composition of these materials is given in Table I. Tensile specimens having a reduced section 1/4 in. diam by 3 in. long were machined from materials which were refined, cast, forged, and swaged in the authors' laboratories. The specimens were annealed for 1/2 hr at 1150°C, a treatment which produced grains having a diameter of approximately 0.5 mm. This rather large grain size was used to facilitate later examination of the substructure. Duplicate specimens of pure nickel and of each alloy were strained various controlled amounts in tension at room temperature and recovered for 1 hr at 800°C. (This strain induced prior to recovery will be referred to hereafter as the "prestrain.") One of each of the recovered specimens was pulled in tension at room temperature to obtain the stress-strain curves. The other bar was cross-sectioned in the gage length, carefully polished, and deeply etched to remove all cold-worked material. This specimen was then examined by the X-ray microscopic technique2 to determine the nature and magnitude of the substructure. The use of duplicate specimens permitted a direct correlation between tensile properties and substructure characteristics. X-ray microscopic studies were made with an apparatus constructed to have an average resolving power of about 4 microns. The monochromatic radiation reflected from grains which were oriented favorably was recorded on fine-grain photographic plates. These were examined at Xl00 which represents the true magnification, since there was essentially none in the X-ray system. This permitted detection of angular differences between subgrains of as little as 10 min. A very large number (over 100) of grains for each specimen was examined at this magnification and the number of substructure boundaries per grain was tabulated. An accurate relative measure was obtained under fixed experimental conditions, e.g., same grain size, resolving power, magnification, etc. The greatest source of error lay in counting the subboundaries, but this proved to be surprisingly small when repeated counts were made by different investigators. Furthermore, as the subsequent analysis indicates, whatever human error was introduced was not significant. Analysis of the Substructure Data When the number of substructure boundaries per grain was plotted against the frequency, skew (asymmetrical) distribution curves of the type shown in Fig. 1 were obtained. These are smoothed curves for the 1 atomic pct Ti in nickel alloy subjected to various prestrains and are representative of the curves obtained with all the metals. Since skew-distribution curves cannot be analyzed by elementary statistical methods, detailed investigations were undertaken in order to 1—test the consistency

Jan 1, 1955

By G. T. Higgins

PREVIOUS workers1,2 have found evidence of exaggerated grain growth or secondary recrystallization on annealing sponge zirconium at temperatures high in the a, phase field, but no details of the orientation relationship between the secondary grains and "as-recrystallized" matrix were reported. In other hexagonal metals, namely dilute Mg-A13 and Cd-zn4 alloys, secondary recrystallization has been observed in which the secondary grains are related to the primary recrystallized structure by rotations about the c axis. These rotations are thus comparable with the rotations about the (111) axis observed in the secondary recrystallization of fcc metals. In the current work secondary recrystallization has been observed on annealing iodide zirconium at 800°C and the associated changes in crystallographic texture have been examined. The material employed was arc-melted iodide zirconium of the following composition: Impurity O H Fe Hf Pb I Ni C1 A1 ppm by wt 130 5 230 98 23 28 200 39 30 This was received as 0.25-in. plate, and, prior to the annealing studies, was cold-rolled to 0.040 in. Specimens 1 in. sq were chemically polished and annealed for various times at 800°C in a vacuum better than 5x 10-6 Torr. For metallographic examination specimens were first chemically polished and then anodized8 to enhance contrast between the grains when examined under polarized light. Changes in crystallographic orientation associated with the development of secondary grains were followed by (1011) and (0002) pole-figure determinations using a conventional Schulz goniometer in reflection. Filtered Cr Ka radiation was employed and great care was taken to avoid spurious re- sults due to the close proximity of the Bragg angles for the (1011) and (0002) reflections. Figs. 1 and 2 illustrate the change in grain structure on annealing at 800°C. After 24 hr the structure has ceased to be equiaxed due to the development of certain grains in preference to others. It is notable that the secondary grains do not grow to the extent observed in sponge zirconium.1,2 This appears to be due in part to the fact that normal grain growth is inhibited in the less pure sponge zirconium, with the result that the driving force for secondary recrystallization remains high, while at the same time the number of grains able to develop in the presence of the impurities is also smaller. As a consequence, in sponge zirconium those grains that do develop preferentially are able to grow into the fine -grained matrix without impingement, while in iodide zirconium the preferential growth of many grains leads to early impingement. The pole figures determined for specimens annealed for 5 min and 24 hr at 800°C are illustrated respectively in Figs. 3 and 4. These indicate that the dominant feature of the initial recrystallized texture consists of basal planes at an angle of 321/2 deg to the sheet surface, with a (1120) axis lying parallel to the

Jan 1, 1967

By Ronald C. Koo

THE effect of grain size on the mechanical properties of the bcc metals has been a subject of intensive theoretical and experimental study.'-l5 Quantitative relationships have been established experimentally between yield stress and grain size and between the ductile-brittle transition temperature and grain size in a number of metals.6"15 Much significance has therefore been attached theoretically to the grain size dependence. In all these experiments, different grain sizes were always achieved by annealing specimens at various temperatures. The implicit assumption was that any change in the dislocation substructure or in the distribution of impurities which might occur simultaneously with the production of various grain sizes had only a negligible effect on the mechanical properties. The validity of this assumption, however, is questionable. transformation in iron-nickel alloys is actually an extraneous phenomenon due to inadvertent compositional changes in the martensite if the heating rate is not sufficiently rapid. This complication can be avoided by up-quenching for the reversal treatment,5 and then the stabilization does not appear. Clearly, the lattice imperfections and strengthening produced by the reverse transformation are not responsible for the marked stabilization which has been observed by other investigators in these alloys. Data will be presented in this note to show that, at least in recrystallized tungsten of commercial purity, the difference in the ductile-brittle transition temperature of specimens annealed at various temperatures is more a result of a variation in the distribution of impurities rather than of the difference in grain size produced by the anneal. Ductile-brittle transition temperatures in tension were determined on powder-metallurgy tungsten specimens recrystallized at various temperatures. Tensile specimens having a gage length of 1.50 in. and gage diam of 0.18 in. were recrystallized at 1450°, 2000°, 2350°, 2550°, 2750°, or 2800" for 30 min in a vacuum furnace at a pressure of 1 x 10"5 mm of Hg and then tested at a constant extension rate of 8 x 10 per sec in an argon atmosphere from 100" to 800". Typical quantitative analyses of impurities are given in the Table. These results show that, within the precision of the analyses, see Table, annealing did not result in any detectable change in the impurity contents of the specimens, nor was there any detectable difference in purity between specimens having large differences in grain size annealed at the same temperatures . The results of the tensile tests yielded three distinct ductile-brittle transition curves approximately 225' apart. As shown in Fig. 1, data of specimens annealed at 1450°C and those of specimens annealed at 2000°C (O) fell on Curve A. Data of specimens annealed at 2350" and 2550°C fell on Curve B, and those of specimens annealed at 2750" and 2800°C fell on Curve C. The decrease in ductility with increase in annealing temperature became so pronounced that one third of the specimens annealed at 2750" and two thirds of the specimens

Jan 1, 1963

By Thomas E. Garnar

Zirconium and hafnium are curious elements because they are almost always found together in nature. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium's chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and Von-Heresey detected it using x-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO4) and less commonly as the oxide baddeleyite (ZrO2). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. Zircon is always a coproduct from TiO2 mining and processing. During World War I it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s when Zircon Rutile, Ltd. began mining at Byron Bay on the east coast of Australia that zircon was first used as a foundry sand. Later in the 1940s, NL Industries, Humphreys Gold Corp., and E. I. du Pont de Nemours & Co., Inc. began production of zircon sands from fossil beaches in northeast and northcentral Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties as well as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by South Africa and the US. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, China, Thailand, and Brazil. Undeveloped heavy mineral beach sand reserves containing zircon are known to occur in Egypt, Malawi, Senegal, and Tanzania. Locations are shown in Fig. 1. Mineralogy Zirconium and hafnium are always present together in naturally occurring compounds. Most commonly they form as the silicate sometimes containing iron, calcium, sodium, manganese, and other elements. Less commonly they are found as oxides in combination with titanium, thorium, calcium, and iron. Zircon is the most common form. It is extremely resistant to weathering, therefore, often it is present in ancient beach sands and placer deposits. Although resistant to alteration from external sources, it is vulnerable to internal alteration as the result of thorium and uranium substituting for zirconium either in the zircon lattice or in solid solution. Alteration to the metamict state takes place as radioactive emanations from these elements disorder the crystal lattice, accompanied by hydration, reduction in specific gravity, and changes in color. The mineralogy of zircon and baddeleyite and variation of physical and chemical properties are shown in Table 1. The effects of zircon's internal alteration and darkened color can be corrected by heating to 1000°C for 30 min or so. A certain time-temperature relationship makes it possible for decolorization and reordering of the crystal lattice to take place when heating at higher temperatures for shorter periods or at lower temperatures for longer periods. After heating, x-ray diffraction patterns are sharper, the grains may be harder, and except for particles of malacon, the grains will be white or colorless in the absence of grain surface coatings. The color change is only temporary and the particles slowly darken with time. Zircon fluoresces light yellow in shortwave ultraviolet light. If exposed to ultraviolet light for extended periods of time, white (calcined) zircon turns purple. With time the induced color begins to fade and eventually disappears (e.g., calcined Florida zircon exposed to ultraviolet light for 24 hr still retains faint, but discernible, purple color after six months).

Jan 1, 1983

By R. F. Krueger, L. C. Vogel, P. W. Fischer

Previous studies have shown that the permeabilities of sandstone cores are markedly reduced following exposure to drilling fluid and subsequent clean-up with oil at high-pressure gradients. Laboratory experiments reported in this paper indicate that permeability damage from drilling mud or water can be substantially avoided through use of an initial low-pressure gradient followed by gradually increasing gradients during clean-up by reverse oil flow. On the other hand, attempts to improve the permeability of damaged Berea and oil formation cores with high-rate oil backflush (simulated well stimulation) and low-rate clean-up gave erratic results. Essentfully complete permeability repair was achieved in most of the fresh water-damaged cores from Miocene and Pliocene oil-producing formations; only minor improvement was noted generally in tests with both water-and mud-damaged Berea sandstone. Field well stimulation treatments using high-rate back-flush resulted in long-term productivity improvement when production was brought in at gradually increasing production rates and then restricted to a steady value less than the maximum possible rate. Wellbore plugging at high production rates correlated with increasing solids content in the produced oil. Observations and results from these tests agree with current concepts that formation damage in water-sensitive rocks results from movement and bridging of formation fines, rather than from clay swelling alone. INTRODUCTION Many laboratory studies1-g have shown that the permeabilities of sandstone cores are often markedly reduced following exposure to fresh water or water-base drilling mud filtrate. However, work with cores in the restored state has demonstrated that, although permeabilities to water may be very low for sandstones containing hy-dratable clays, flow of oil can often restore a substantial portion of the effective permeabilities to oi1.Neverthe- less, water invasion into water-sensitive sandstone cores results in varying degrees of permanent reduction in permeability to oil.24' Based on field data, Wade's statistical study" of well completion effectiveness also indicated a correlation between productivity damage and water invasion during completion. Similar damage can result from fluid invasion during workover. Nowak and Krueger' and Bertness4 observed in their early work (1951-53) that formation damage in water-sensitive sandstones was associated not only with swelling of expandable clays but also with movement of dispersed particles. Subsequent work by Monaghan et al." (1959), Atwood'' (19641, Mungan" (1965) and Gray and Rex'" (1965) has led to general acceptance of the hypothesis that permeability damage in water-sensitive formations is caused by migration of finely dispersed minerals and bridging in "brush heap" arrangements at pore constructions. In laboratory studies, Monaghan et al.' found the use of chemicals to be of only minor value for repairing formation damage. Atwood? however, was successful in substantially repairing damage in a number of low-permeability cores using an n-hexanol flush. In the field, except for treatments with acids, the use of chemical washes to reduce wellbore damage has had limited and sporadic success and generally is unpredictable. A statistical analysis of stimulation treatments in silt-blocked wells has shown that physical manipulation of wash materials is more important than chemical composition." The recent work reported on formation damage in water-sensitive sands brings to mind the results of some unpublished exploratory work done in 1954 in connection with drilling fluid studies.' This laboratory work and subsequent field stimulation treatments indicated a beneficial effect of controlled pressure drawdown and the associated production rate on formation clean-up. This paper reports the results of this work and more recent supplemental experiments on the clean-up of water-sensitive sandstones damaged by water or filtrate invasion. PERMEABILITY RECOVERY AFTER DAMAGE BY DRILLING MUD APPARATUS AND TEST SAMPLES A drilling mud circulating system was used to expose cores to simulated wellbore conditions. The mud flow system is the same as that described by Krueger and Voge17 except that no provision was made for scraping

By Tasuku Fuwa, John Chipman, David H. Kirkwood

Fe-C-Si alloys in silica crucibles were held at 1600°C in a controlled atmosphere of CO and Co2 and the approach to equilibrium was obsertsed. Results were not of sufficient precision to establish the activity and interaction coefficients. Observations 012 the equilibrium provided an average value for the standard free-energy change which differed by + 1.1 kcal from the earlier accepted value. The C-SL relation at other temperatures is calculated and shown graphically. IN the refining of steel in an acid-lined furnace, it is well known that, unlike in basic refining, a very significant amount of silicon may remain dissolved in the metal even when the carbon content approaches a final endpoint. Further, it is known that the residual silicon increases with increasing temperature. The quantitative relation between silicon and carbon can be calculated for equilibrium conditions from data already available on the Fe-C-O and the Fe-Si-O systems. Such equilibrium calculations could show us approximately the limitations within which the reaction would be expected to operate in practice. In the oxidation of a bath containing both carbon and silicon it is well known that at low temperatures silicon is preferentially oxidized first. It can be shown by calculation that at high temperatures carbon will be oxidized preferentially. It is the purpose of this paper to record direct observations on the Si-C relation by means of experiments carried out in an atmosphere of carbon monoxide for Fe-C-Si alloys contained in silica crucibles. When such a system is brought into equilibrium, at a fixed temperature, the composition of the liquid metal is governed by the following equations: Both K1 and K2 are known with a fair degree of accuracy, and may be calculated from the tabulated In general the percentage of CO2 is extremely small compared to that of CO and in the experiments to be described the partial pressure of the latter was generally only slightly below 1 atm. EXPERIMENTAL METHOD The induction furnace employed was the same as that described by Rist and chipman' and by Fuwa and chipman.2 It was modified slightly in view of the change from alumina to silica crucibles. The small silica crucible was surrounded by a thin susceptor of molybdenum sheet which in turn rested inside a zirconia crucible. Since the zirconia was subject to breakage, it was supported inside an alumina crucible. The charge consisted of 30 to 35 g of electrolytic iron along with the required amounts of refined silicon and graphite to produce a melt of required composition. Purified carbon monoxide and carbon dioxide were passed into the furnace through carefully calibrated flow meters. Two separate and independent series of experiments were carried out. In Series I (D.H.K.) the melt was held in the furnace at 1600°C for periods of time up to 6 hr. Samples were taken at intervals in silica tubes and were analyzed for carbon and silicon. The results of the last one or two samples taken from each experiment and the direction in which equilibrium appeared to be approached are shown in Table I. In Series II (T.F.) the silica crucibles were of less satisfactory strength and the melts were held at 1600° C for periods of only 2 to 4 hr. In heats number 29 to 45 inclusive, the metal was cooled in the furnace and the ingot itself served as a sample for analysis. In heat 46 and all subsequent heats, samples were withdrawn in silica tubes at the termination of the heat, and these samples were analyzed. The results of all of these experiments in which equilibrium appeared to be approached are listed in Table II.

Jan 1, 1965

By D. D. Pollock

Many constitution diagrams do not indicate the limits oJ solid solubility of the silver-rich solid solutions below 200°C. Thermoelectric measurements were employed to determine this limit in the nieighborhood of room temperature. The appearance of a second phase causes a discontinuity to occur in the tkevtrroelectric power as a function of cornposition at constant temperature and pressure. This discontinuity was employed to determine the limits of the silver-rich terzinal solid solutions of the Ag-A l, Ag-As, Ag- Bi, Ag--Ge, Ag-In, Ag-Pb, Ag-Sb, and Ag-Sn systenls at 30°C. CONSIDERABLE work has been done on the constitution of binary alloys of silver. The available data have been compiled by Hansen1 and Elliott.2 However, many of the binary diagrams do not show the limits of solid solubility of the silver-rich solutions below about 200° C. This work was undertaken in an attempt to extend these limits to the neighborhood of room temperature . PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pct (by weight) of impurities. The materials were weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony alloys were melted in A1203 crucibles, under a boric anhydride cover, and were poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles; they were also covered with boric anhydride and poured into split graphite finger molds. The $-in.-diam ingots were heated to 750°C and were forged and hot-rolled down to 0.1 by 0.1 in. The wires were pickled in a 25 pct HNO3-75 pct H2O solution to remove any oxygen-rich surfaces. The wires were then annealed at 550°C for 2 hr in a dissociated ammonia atmosphere. They were then furnace-cooled for 20 hr to room temperature in this atmosphere. The wires were cold-drawn to 0.0808 in. diam. The finished wires were again annealed at 550°C in the same manner as in the first anneal. Thermoelectric Power. The thermoelectric power of a single specimen of each alloy was determined against pure silver which contained a maximum impurity content of 0.014 pct by weight. The wire specimens were straightened and then cleaned with ethyl alcohol. They were then reannealed in the same way as the finished wires to assure that any residual stress would be at a minimum level. Previous work has shown that the presence of small amounts of stress has the effect of decreasing the thermoelectric power. The alloy specimen was soldered to the pure silver wire to form the measuring junction. A standard set of copper leads was then soldered to the reference junctions of the thermocouple. These junctions were maintained in separate dewar flasks which contained finely shaved melting ice during the test. The thermal electromotive forces of the thermocouples were measured at four temperatures between 15° and 45°C. A known source of electromotive force was balanced against the output of the thermocouple until a null balance was reached. The data were then expressed in terms of the thermoelectric power at 30°C. The results were then converted to absolute thermoelectric power, s303.3 These data have an average error of less than ±0.2 pct. RESULTS AND DISCUSSION All of the experimental data are given in Table 11. Since the electromotive forces of the binary alloys of silver were determined against the pure silver from which they were made, the resultant thermoelectric powers are only a function of the intentionally added binary elements at the constant test temperatures. This provides a direct measure of the effects of the alloying elements. The absolute thermoelectric power of an alloy of silver is given4 by:

Jan 1, 1968

By Roy J. Helfinstine, Gilbert H. Cady

One of the most urgent needs in the field of coal combustion is the ability to predict the performance of a coal from knowledge gained from small-scale tests. Numerous types of analyses and tests are conducted on coal, including the proximate and ultimate analyses, heating value, varieties of sulphur, ash analysis, ash fusion temperatures, free swelling index, petrographic analysis, and Gieseler. plasticity. The Illinois Geological Survey has made an intensive study of the value of these tests for judging the performance characteristics of the coal as actually utilized. To date, three reports1,2,3 have been issued, and another is being prepared. The present paper briefly summarizes some of the results found in the studies. Equipment The equipment used for the tests is described in some detail in the above mentioned publications. Briefly, it consisted of a domestic stoker, cast-iron boiler, and water-cooled heat exchanger, which were operated as a forced circulation hot-water system. The entire unit was mounted on scales. Instruments for recording the per- formance of the coal included a hot-water meter to indicate the quantity of water flowing through the boiler; a two-pen, mercury-actuated thermometer to record the temperatures of the water entering and leaving the boiler; a chemical-type meter to record the percentage of CO2 in the stack gases; a pressure gauge to record the static pressure in the stoker-air duct; and a multipoint potentiometer to record the temperatures in the stack and room, and the opacity of the stack gases. A 16 mm motion picture camera was available for taking pictures of either the fuel bed or the scale dial. Procedure The tests described in this report can be conveniently divided into three phases. For the first phase, a load of 5 or 6 tons of unwashed coal (usually screenings) was obtained from each of fourteen Illinois mines. These coals were all crushed and screened to a size of 35 in. (square hole) by 8 mesh. Combustion tests were made on a part of this raw, screened coal. Another portion was passed over a concentrating table to reduce the ash to what was considered to be commercially reasonable, and combustion tests were made on this upgraded coal. The ash content of the remaining coal was reduced to a still lower figure by passing it over the washing table with greater reject, or by standard float-sink procedure. This cleaned fraction was then tested in the stoker-boiler unit. Thus three coals with varying ash content were tested from each mine. For the second phase reported here, coals were obtained from four Arkansas mines and tested as received and after passing over the concentrating table with a normal reject. One Illinois coal was tested in the "washed" condition only. The third phase included tests on commercially prepared stoker coals

Jan 1, 1950

By S. R. B. Cooke, Y. S. Kim, I. Iwasaki

lron oxides or the gangue minerals of iron ores can be made to float, depending upon the choice of collector. The selectivity of the separation is controlled by the accompanying chemical and operating conditions. In this report the findings on the general flotation characteristics of magnetite are summarized and the results are compared with those obtained for other iron oxides. Depending upon the choice of collector, either the iron oxides or the gangue minerals of iron ores can be made to float, the selectivity of the separation being controlled by the accompanying chemical and operating conditions. The mechanism by which a collector exerts preferential affinity for either group of minerals has been a subject of extended discussion. Previous investigations on the electrokinetic properties and flotation characteristics of hematite,' goethite,2 and quartz3 have demonstrated the electrical nature of the interaction of the collector with these oxide surfaces; anionic collectors are effective on positively charged surfaces and cationic collectors on negatively charged surfaces. Thus, from the differences in the electrokinetic properties of the above-named oxides, a theoretical basis has been provided for their separation by some typical collectors. Examination of the results reported for hematite and goethite shows that their electrokinetic properties and flotation characteristics are remarkably similar. It is of considerable interest, therefore, to examine similar information for magnetite, another common iron oxide, in order to consolidate the flotation characteristics of the three principal minerals of oxide iron ores. Such information is practically significant in the up-grading of both natural and artificial mag- netite produced from taconite, and in the treatment of partially oxidized magnetite ores. Information on maghemite and lepidocrocite, polymorphs of hematite, and goethite, respectively, is also of some theoretical interest in ascertaining the effects of crystal structure and of hydration in the iron oxide group. This article reports the findings on the general flotation characttxistics of magnetite, and compares the results with those obtained for other iron oxides. Experimentally, tlhe surface properties of magnetite were investigated by electrophoresis, and by measurement of the aclsorption of some typical flotation collectors. Its flotation behavior was tested by contact angle measurements and by simple flotation tests using a modified Hallimond tube. The basic information thus gathered was shown to be directly applicable to the interpretation of the results of batch flotation tests made on an artificial mixture of magnetite and quartz. EXPERIMENTAL MATERIALS Magnetite: Magnetite concentrate from Port Henry, N. Y., was further purified by fine crushing and magnetic separaiion, and was used throughout this investigation. For flotation tests the 150/200 mesh fraction was iso1ated and was cleaned by leaching briefly with warn 0.1 N HC1 followed by repeated washing with demineralized water. The final sample analyzed 71.71 pct Fe, 22.37 pct Fe" and 0.47 pct insoluble, and was stored in demineralized water. For e1ectrophoresis and adsorption measurements, the —400 mesh fraction of the magnetite concentrate was ground dry in a pebble mill. The surface area of the ground sample, as determined by the gas permeability method, was 70,000 sq cm per g. Since artificial magnetite has been reported to possess somewhat different physical properties than those of natural magnetite, it also was briefly examined. Preliminary flotation tests on a sample of artificial magnelite, prepared by reducing Brazilian hematite in a C0/CO2 mixture and analyzing 71.94 pct Fe and 23.78 pct Fe'', gave, however, nearly identical results with those using natural magnetite. It was concluded that artificial magnetite behaves similarly to natural magnetite. Samples which had been magnetically separated showed a tendency to cluster together due to residual

Jan 1, 1962

By W. R. Aufricht, E. H. Koepf

The theory, measurement, and application of capillary forces in reservoir rock have been treated ex-tensively in the various petroleum publications.1,2,3,4 These forces are of prime importance in oil production, and data on capillary properties are among the most important tools used in the study of reservoir mechanics. The principal application of measured capillary pressure data by the production and reservoir engineer is in the determination of the initial distribution and mobility of fluids in the reservoir. The distribution refers to the magnitude of the oil and interstitial water saturations under capillary equilibrium conditions and to their variation throughout the reservoir as a result of changes in rock properties and nearness to free water. The magnitude of the water (or oil) saturation, as well as the porosity, is required in volumetric calculations of oil in place. In low permeability reservoirs, where long transition zones are common, the magnitude of the oil content, even below the depth interval where commercial rates of flow of oil can be obtained, must be evaluated since this oil contains energy available to the production of the remainder of the reservoir. The mobility of the water phase is of particular importance in water-flood calculations since mobile water may condemn what would otherwise be a successful water flood. In reservoirs with predominantly small pores, high immobile water contents are possible. Conversely, reservoirs with predominantly large pores may contain mobile water even though the interstitial water contents are relatively low. This presentation reviews the distribution and mobility of interstitial water contents as determined from capillary pressure data and shows typical data for various types of carbonate reservoirs. A discussion of the variations found in different types of carbonate reservoirs is given. DISCUSSION Interpretation of Laboratory Data Fig. 1 is a typical laboratory capillary Pressure curve where water saturation as Per cent of Pore space is plotted vs capillary Pressure (psig) for an air-water system. This par- ticular curve was obtained by measurement on a sample of San Andres dolomite with intergranular-type porosity. The sample studied had a permeability of 10.0 md and a porosity of 18.8 per cent. The capillary pressure-saturation relationship illustrated is an inherent property of the rock (a function of the size and distribution of the pores) and represents the ability of this water-wet rock to retain water against the pressure differential exerted by a non-wetting fluid (oil or gas) to remove it. In the laboratory a known pressure differential is exerted from a pressure source; in the reservoir the pressure differential is controlled by the density difference between the hvdrocarbons and the water. The laboratory capillary pressure values may be converted into terms of equivalent height of water column using known values of reservoir oil and water density and measured or average values of interfacial tension

Jan 1, 1958

By J. H. Wernick, S. Geller

A number of new AB, compounds, in which A is a rare earth or yttrium atom and B is Al, Mn, Fe, Co, or Ni, having the cubic MgCu, structure (Laves phase) are reported. In most of the compounds, the interatomic distances are normal; the lanthanide contraction is observed. However, in the compounds CeB2, B = Fe, Co, Ni, Ce appears to have a valence substantially greater than three; in CeAl2, Ce appears to be trivalent. These results are interpreted as vesulting from an energetically more favorable situation for the 4f electron of Ce to be lost to the 3d band of Fe, Co, nnd Ni. Evidence for the existence of homogeneitj! ranges in these compounds is presented. THE purpose of this paper is to report on the crys-tallographic investigations of a large number of new compounds, Table I, with the MgCuz structure (cubic Laves phase). It is a part of a continuing study of the magnetic properties and structures of binary systems involving the rare earths. In a previous paper' some of the magnetic properties of such systems were reported briefly. We have also reported2 a number of compounds of the CusCa type. The compounds were prepared by induction melting in Argon atmosphere of mixtures of stoichiomet-ric amounts of the constituent elements.* For most of the compounds fused alumina or silica crucibles were used as the containing vessel; graphite crucibles were used to prepare CeA12, NdAl2 and TbA12. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis-type Norelco cameras of 114.6 mm diam. The compounds AB2 belong to space group Fd3m-Ol with 8A in a): (000; 01/2 '/2;3) + 000-; b % XA and 16B in dl: (000; oVa %; 3) + 5/87; % %; 7e % Vs\£>. Because the intensities of the reflections on the powder photographs of the different compounds are similar, relative intensities were computed only for DyMnz for CrKa radiation, Table 11. In the calculation of intensities, the Thomas and umeda3 atomic scattering factors, corrected for dispersion,4 were used. The agreement between observed and calculated intensities leaves little doubt that DyMnz has the MgCuz structure. Crystallographic data for the ABz compounds are given in Table JII. Twelve of these compounds have been reported by other authors. A comparison of the published results with our work is given in Table W.* ers of elements of lower purity, to peritectic reactions in some cases, and to the presence of homogeneity ranges in these alloys, so that melting losses would still result in single phase alloys. The possibility of existence of homogeneity ranges in these compounds was investigated systematically only for GdMnz. At room temperature, the solid solution range is between

Jan 1, 1961

By Frank T. Weems

The basic operating properties of the DorrClone are discussed and certain metallurgical applications which exploit these properties are presented. An effective method of controlling the consistency of the DorrClone underflow is described. THIS paper presents in a general manner some of the applications of the DorrClone (Dutch States Mines cyclone) in the metallurgical and heavy chemical fields. Technical or mathematical analyses of the design factors and of the mechanism whereby the cyclone effects its separation have been capably treated in a series of previous papers.'-' Engineering and operational aspects of a few installations and laboratory tests have been chosen to emphasize the unique classification characteristics of the DorrClone and to illustrate its utility in certain difficult situations. Its use in coal washing and heavy-media operations are not considered. Some 25 or more industrial installations and applications of the DorrClone in the metallurgical fields are operating at present, ranging from single trial units to complete batteries composed of a multiplicity of units. The data were obtained in part from some of these, and in part from operations of units at the Westport Mill, the laboratories and testing plant of the Dorr Co. at Westport, Conn. The DorrClone was developed, in principle, by the research dept. of the State Mines, Limburg, Holland, during World War 11. Its first use was to dewater a —50 micron sand used as a dense medium in coal washing. The metallurgical wet cyclone was first publicized by Driessen and Yancey and Geer.6 ince then the cyclone has been studied as a means of de-watering, heavy media concentration, and fine size classification. The DorrClone is shown in Figs. 1 and 2. pulp to be treated is pumped through the feed nozzle, A, into the feed cylinder, B. The feed nozzle is of rectangular cross-section, the outermost edge being tangent to the feed cylinder walls. Feed shims, C, may be attached to the innermost walls to adjust the open area of the feed nozzle available to entering pulp. The tangential injection of feed under pressure supports the vortex action of the pulp that has been detained in the cyclone; the centrifugal forces of this vortex throw the coarse particles to the walls of the cone, D, where they collect and pass downward and out through the adjustable apex opening, E. The fine particles contained in most of the water that entered with the feed pulp move to the inner spiral of the vortex and flow out through the vortex finder, F, contained in the orifice plate, G, which forms the top of cyclone chamber. The overflow pulp may then spray freely into a spray chamber, H, surmounting the cyclone or pass directly into a 90' elbow, I, of somewhat larger diameter than the vortex finder. Installation Where more than one cyclone is to be installed, best overall efficiency and ease of control are obtained with equal distribution of both pulp volume and weight of solids among the cyclones, and with the same pressure being maintained at each cyclone feed nozzle. Fig. 3 is a suggested arrangement for feeding two or more cyclones in parallel. Feed pressure control: Under normal operating conditions it is not unusual for some surge to exist in the feed that is to be sent to the cyclone. As will be discussed later, surges in the solids content of the pulp are usually not of great operational consequence, but surges in feed volume are a problem. Several systems have been devised for absorbing surges in feed volume, each involving a surge tank. If the surges are small and fairly rhythmical, a tank of sufficient size might be installed to dampen out

Jan 1, 1952

By Robert L. Davidoff

INTRODUCTION The impact of taxation differs substantially from state to state in a complex fashion that depends on both the physical characteristics of a mineral deposit and on the price of the mineral commodity relative to its costs of production. A comparative analysis of the tax structures of eight states (Arizona, Colorado, Idaho, Montana, Nevada, New Mexico, Utah and Wisconsin) showed wide variations in rates of return for any given type of mineral property, with no state having either the most burdensome or least burdensome tax structure under all circumstances. Three hypothetical mineral operations were analyzed: a producing open-pit copper property, a non-producing underground platinum operation, and a non-producing underground gold operation. None of them corresponds exactly to an existing property. Each of these property types is further defined to have ore feed grades at three different levels, leading to three potential profitability levels, referred to in this paper as "economic", "marginal" and "subeconomic". Thus the differential impact of state tax structures is measured for mineral properties of different types, as well as for different profitability levels. Montana is used as the base case. This study does not address the topic of corporate structures or tax consolidation. There are no costs assumed external to the operation of the deposit (e.g. exploration to locate additional deposits). Two types of analyses were performed for this study. The first calculates the total cumulative tax payments in each state using all applicable taxes (including U.S. federal income taxes and examines the resultant differences in discounted cash-flows rate of returns DCFROR's amoung the eight states. The second is a sensitivity analysis that examines each type of state tax separately (i.e. state income, property, and severance taxes) in order to isolate and examine the differences in tax payments that are due to the difference in rates and methods of computing specific types of taxes in each state. The results of this study serve to illustrate the complex nature of interactions among various taxes. For example, property tax is a deduction in calculating severance tax in some state. Changes in property-tax and severance-tax payments both enter into the calculation of state and federal income-tax liability. This, in turn, could change the timing and usage of tax-loss carry forward amounts and investment tax credits. Additionally, the physical characteristics of a property, the method and costs at which the mineral will be extracted, and the profitability level at which each property operates will affect tax treatment. Each mineral operation was evaluated at three different predetermined profitability levels, referred to using the terms economic, marginal and sub-economic. These three profitability levels are defined by the ore feed grades of the primary commodity that yield in constant terms, approximately an "economic" 18% DCFROR, "a marginal." 10% DCFROR, and a "sub-economic" 5% DCFROR, respectively, under the Montana tax structure. In the analyses, the mining and processing parameters for each of the three types of properties were assumed to be identical for each of the eight states. It was assumed that each operation produces at full operating capacity throughout its life. This implies the level of mineral commodity demand will support the inferred commodity price, such that each operation will be able to sell all its output. The analyses performed for this study were done using a comprehensive economic evaluation simulator that is used in the Bureau of Mines, Division of Minerals Availability MAS program to perform DCFROR analyses. All economic evaluations performed upon these data (see appendix 2) were in constant January 1981 dollars. By-product prices used for the analyses were: [Gold $425.00/troy ounce Palladium$200.00/troy ounce Silver $ 10.00/troy ounce] Typical cash-flow calculation layout is given in Appendix 3. The initial step for each evaluation is to define an "economic" profitability level scenario. An 18% DCFROR rate in Montana was considered the

Jan 1, 1985

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days' production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

By John W. Bell

In the introduction to an excellent pamphlet, John Gross' makes the following statements: Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere. Realizing the situation, the Milling Committee of the American Institute of Mining and Metallurgical Engineers, through its secretary, E. A. Hersam, studied the milling industry and, because of the apparently hopeless lack of agreement in the Kick versus Rittinger dispute (5, 13, 14, 0, i8, 19, 21, 22, 23. 24, 30. 34), concluded that a foundation for the theory of crushing was of primary importance. The numbers in the paragraph quoted refer to papers listed by Mr. Gross in his Bibliography on Crushing and Grinding.1 One is obliged to infer that these papers show "hopeless lack of agreement in the Kick versus Rittinger dispute." No. 22 is a paper by Arthur O. Gates2 and No. 23 is one by the writer.3 Employing the subject matter contained in papers Nos. 22 and 23 2,3 the writer will show that their authors formulated identical conclusions, based solely on experimental evidence. Exactly the same defect in the Stadler hypothesis was described in each of the two papers, although entirely different experimental methods were employed in uncovering it. Both of the authors, independently, formulated the conclusion that Rittinger's was a true hypothesis and Stadler's false. The evidence in a third paper4 will be employed to prove that Stadler's hypothesis, when examined experimentally, is worthless. STADLER'S HYPOTHESIS WORTHLESS It is the writer's opinion that the evidence available in 1915 and the corroborating evidence in 1916 was amply sufficient to eliminate the need for any further consideration of Stadler's hypothesis. Certainly the evidence produced in 1918 dealt this hypothesis its coup de grace. It follows, therefore, that in the year 1918 there was only one credible hypothesis left-the Rittinger hypothesis. Gates' Opinion What information is available in Mr. Gates' paper?2 His conclusions are not consecutively summarized, none the less they are perfectly clear. On page 876, Gates says, and it is a very significant utterance: But my results show, among other things, that many more of Stadler's energy units are obtained per foot-pound-applied in coarse than in fine crushing. This suggests a doubt as to the correctness of his unit, since one would expect a foot-pound-applied to produce the same number of "energy units," whether the feed and resulting product were coarse or fine. When Rittinger's theory is applied, the number of mesh-tons (my unit of surface produced) is

Jan 1, 1942