Search Documents

By D. J. Freeh, W. E. Horst, R. C. Kellner

This paper is concerned with the description of grinding characteristics in a batch grinding system. A mathematical model was developed and used for simulating the system on an analog computer. A general equation describing the change of selected size fractions with respect to time is presented. The empirical verification of the model is discussed. In order to understand the performance of a grinding system, it would be desirable to have a mathematical description of the system's behavior. The development of a mathematical model to describe the performance of a batch dry-grinding operation was investigated. This is the first step toward reaching the objective of a practical mathematical description of a grinding system that could be employed for process control and optimization of a simple or complex grinding circuit. Although this article is concerned only with batch grinding performance, experimental work is being conducted to extend the model to continuous grinding systems. BASIC PROCESS CONSIDERATIONS In a paper dealing with the probability theory of wet ball milling, Roberts1 correlated the rate of change of oversize material, C, with energy input, E, as follows where the energy input is expressed in power/unit mass and k is a constant for each particle size. Experimental grinding studies were made by Bowdish2 to extend the previous work of Roberts. The work of Bowdish also showed that the rate of breaking of oversize particles in a ball mill is proportional to the concentration of oversize particles present. He further demonstrated that breaking of oversize particles is proportional to the surface area of the balls used for grinding. Rate equations were presented and it was concluded that grinding could be considered as a first order phenomenon according to the rate equation [2] di which is in accordance with Eq. 1. In Eq. 2, the effect of ball area is included in the constant k,. Other rate equations were reported to show the effect of a change in ball area and removal of fines during grinding. Correlation studies made by Arbiter and BhranY indicate a first-order rate equation for quartz; however, their data showed less than first-order rates existed for some of the other materials evaluated. More recently Kelsall4 has shown that the rate of breakage of any narrow size range of quartz could be described by a first-order rate equation. Several other investigators5-7 have described grinding behavior in terms of rate equations or kinetics. In general, the rate equations have been described for each particle size; however, the interactions between sizes and the overall relationships that exist have not been considered, at least not in the form of solving a group of simultaneous differential equations. Extensive work has been conducted by various investigators using a probabilistic approach which has expanded stein's' earlier work. Selection and breakage matrices are incorporated in the probabilistic model as contrasted with the deterministic method presented here. A batch grinding operation may be considered as an unsteady-state process from the standpoint that the conditions within the mill are a function of time. Therefore, a plot of mass fraction of the i-th size versus time would give a set of curves as shown in Fig. 1. In these curves X , represents the mass fraction of large size material, X2 intermediate size, and X3 small size material. An examination of these curves shows a strong similarity to the curves that would be obtained from a chemical reaction of the type9 A?B?C, [3] where A would be comparable to the largest size material being broken to an intermediate size, 3, and

Jan 1, 1968

By Arthur Hockman, Howard W. Jaffe, Howard F. Carl

THE problem of establishing practical techniques for evaluating natural corundum ores arose from the desire to improve the existing purchase specifications for crystal corundum procured by the Federal Government for stockpiling. Such purchase specifications had been developed for a large number of products, including minerals and ores considered to be critical and strategic because of the country's dependence on foreign sources of supply. It will be apparent to anyone considering the subject of purchase specifications that the determination of whether or not a submittal meets the specifications is a prime consideration. Consequently satisfactory specifications for minerals should not only incorporate physical, chemical, and mineralogical requirements that are practical but should also establish the means by which both buyer and seller can be assured that materials meet stated requirements. The Munition Board's Material Purchase Specification for corundum, dated February 1954, covered two grades of crystal corundum intended primarily for abrasive use. It established limits of size and of composition: Grade A, at least 95 pct +3 mesh and 92 pct alumina (Al2O3); Grade B, at least 95 pct +7 mesh and 90 pct alumina. It also specified that "of each lot of material, not less than 95 percent shall have a hardness equal to or exceeding nine (9) on Moh's Scale." These specifications were unsatisfactory for several reasons. They did not allow the purchase of lower grades of corundum being used by industry. Neither did they specify exactly what a corundum ore actually was, except that it should contain so much alumina and have a certain scratch hardness. Nothing was said about the abrasive qualities of the material that was to be purchased primarily for abrasive use. During the period 1946 to 1948 supplies of the two grades defined in the then current specifications continued to decrease. Early in 1949 industry recommended that the finer sizes of corundum known as "crystal corundum concentrates," ¼-in. to 16-mesh material, be added to the stockpile specifications and that lower grades of crystal corundum also be included. In the spring of 1949 the National Bureau of Standards and the Bureau of Mines were asked by the Munitions Board to cooperate in developing more practical specifications for grading natural corundum ores. The National Bureau of Standards indicated that it would investigate physical test methods for determining abrasive characteristics of corundum, and the Eastern Experiment Station of the Bureau of Mines at College Park, Md., stated that it would consider the mineralogical aspects of the problem. Members of these two agencies, in consultation with representatives of the Office of Materials Resources of the Munitions Board and of the Federal Supply Service of the General Services Administration, and with the cooperation of industrial suppliers and consumers of abrasive corundum, developed, in a fairly short time, more practical specifications for six grades of corundum ores. The new specifications, issued January 1951, were for corundum, natural crystals, as by this time high-purity synthetic corundum was available and widely used. Nevertheless, for certain specific applications the natural product was preferred over the synthetic material. It has been extensively used in forming snagging wheels. It breaks into more or less cubical particles, whereas artificial corundum fractures into splintery shapes. These produce irregular cuts in glass, while the more symmetrical shape produces a more uniform ground surface. For this reason natural corundum has been preferred for certain types of lens grinding. Pure corundum is clear, colorless alpha alumina (A12O3), but it is rarely found in nature in this form. The most important gem varieties include the blue and yellow sapphires and the ruby. Minute impurities of titanic oxide impart a blue color,

Jan 1, 1955

By G. Derge, R. E. Grace

Diffusivity of bismuth in liquid Pb-Bi alloys has been measured by the capillary reservoir method as a function of temperature and composition. Fair agreement between theory and experiment is found for the measured diffusion coefficients and activation energies of diffusivity and viscosity in dilute lead alloys. The measured diffusion coefficients in the high bismuth alloys describe mass transport in special concentration gradients. THE study of diffusion in liquid metals has been restricted largely to the amalgams over small ranges of temperature and composition. In contrast to this, diffusion and transport of ions and molecules in aqueous and organic solvents have been studied extensively for the past 50 years. The general difficulty of measuring diffusion coefficients in both gases and liquids at high temperatures has been that of eliminating convection currents. Measuring techniques based on freezing and sectioning after the diffusion period1 are not particularly satisfactory because of the volume changes and segregation which occur during freezing. The most promising technique which is currently being developed for liquid metals is the capillary reservoir method. This eliminates convection currents from the diffusion zone and requires measurements only of the length and initial and final compositions of the alloy within the capillary. Anderson and Saddington' have measured the diffusion coefficient of tungstate anions in aqueous Na,W04; Wane4' and Hoffman- ave studied structure and self-diffusion in water and self-diffusion in mercury, respectively, by similar techniques. Selection of the Pb-Bi system for initial study was made for several reasons: I—It afforded a low temperature system for development of techniques which would be suitable for high temperature measurements in liquid iron. This research on diffusion in liquid iron is now in progress as a part of a general program on the rates and mechanisms of slag-metal reactions. 2—Activity data on liquid Pb-Bi alloys of all compositions are available from the emf meas- urements of Strickler and Seltz.9 3—Some data are available on the diffusion of bismuth into solid lead. The measurements on solid alloys were made by von Hevesy and Seith7 for the concentration range of 0 to 2 pct Bi. An appropriate solution to Fick's law (unsteady state) for the capillary reservoir has been found by considering the mass flow which passes through a unit area of surface on a slab of infinite thickness as a function of time. This is the first application of this solution to diffusion measurements, although a similar solution is available for identical boundary conditions.' By analogy with heat conduction, the problem reduces to a perfectly insulated infinite slab at temperature C,, one surface of which is quenched to C, for all times, t. Heat is permitted to flow from quenched surface of the slab to an infinite supply of coolant at C.' (see Appendix). For the corresponding solution for diffusion in liquids, these terms become Where Cu is the initial concentration of component A" in entire capillary at t - 0, C, is the final con- In this case. component A is bismuth, and C, = 0. centration of component A in entire capillary at t = t, C, is the concentration of component A in bath for all t, 1 is the length of the capillary in centimeters, t is the time of diffusion period in seconds, and D is the diffusion coefficient in square centimeters per second. By comparison with solutions to Fick's law used in the solid state, this solution for liquids is similar to the Grube solution for solids, where the change in D with chemical composition is not taken into consideration. Difficulty is to be expected if large concentration gradients are employed and if the concentration gradients extend over an appreciable length of the capillary.

Jan 1, 1956

By L. H. Robinson

Triaxial compression tests on Indiana limestone indicate that chemical additives in the pore fluids can increase or decrease the strength in plastic failure but not in brittle failure. Tests using a series of the sodium salts of dicarboxylic acids show that odd-number carbon-atom chains decrease the yield strength as much as 3.0 x 10 3 psi, and even-number carbon-atom chains increase the yield strength as much as 9.0 x 102 psi. ,The most effective chemical (sodium citrate) decreased the yield strength of Indiana limestone from 16.0 x 103 to 12.0 x 103 psi. The chemical additives investigated have no influence on microbit drilling rate when drilling with zero differential pressure. However, when drilling at a 2.0 x 103-psi pressure differeniial and using an odd-number carbon chain compound as the circulating fluid, the roller bit drilling rates were slower than with water whereas the drag bit drilling rates were faster. One even-number carbon chain compound added to the circulating fluid produces the opposite effect: the roller bit drilling rate is slightly faster than with water and the drag bit slower than with water. INTRODUCTION A Russian book by Rehbinderl published in 1944 generated much interest in the possibility of aiding and accelerating the destruction of solids by the action of a liquid in which the solids are deformed. This book describes a process in which microcracks are generated during elastic deformation. To describe this process, the rock is divided into three zones: (1) the zone in which the destruction takes place, (2) the predestruc-tion zone (an affected area immediately below the destroyed zone) and (3) the undisturbed specimen. Consider a load applied normally to a surface of an infinite slab of rock. Immediately below the point of application of the load, the rock is destroyed by compression or shear forces. Below this area of destruction, because of a great number of discontinuities ranging from defects to weak points in crystals of discontinuities in crystal latices, very small cracks are created in or between the crystals (often referred to as microcracks). Upon removing the load, the broken rock in the destroyed zone could be removed. In the lower predestruction zone, however, the microcracks in and between the crystals could disappear by the process of rehealing, i.e., the molecular attraction from one side of the crack to the other side being sufficient to completely eliminate the crack. Thus, a large number of these microcracks possibly exist only for a relatively short period of time. The concept of small cracks being generated within the crystals of a rock is not unreasonable. If the rock matrix is deformed below the yield point, some of the defects present within the crystalline structure could start small cracks through the interior of the grains. Upon removal of the load, these microcracks reheal (or the newly generated surfaces come back together) so that all evidence of cracks completely disappears. Under various types of loading, and in various types of fluids, the rehealing of these cracks would be time dependent. If a liquid adhered to the surface of a rock, it could penetrate into the microcracks and thus delay or prevent the rehealing process. This suggests that the prevention of healing of the microcracks may be dependent upon the wetting characteristics of the solid. Thus, rocks which are water-wet should be more easily destroyed in water than in nonpolar hydrocarbon liquid. Adsorption of a liquid could also reduce the free surface energy which could explain the decrease in strengths of materials under nonrepetitive-type loading. Rehbinder's work prompted Boozer, Hiller and Serdengecti 2 to examine the effects of pore fluids on the deformation of rocks subjected to triaxial compression over a range of confining pressures, temperatures and strain rates. Fluids which strongly adsorbed on the rock grain surfaces decreased the strength of sandstone and limestone, which deformed plastically. For certain strain

By M. E. Wadsworth, C. H. Pitt

Nickel corrosion in sulfuric acid solutions at elevated temperatures and oxygen wer-pressures was imestigated. Weight loss was 1inear with time and varied directly with oxygen concentration. Independent variation of the possible active species in solution indicated that the undissociated sulfuric acid molecule plays an important part in the corrosion mechanism. The rate determining step was considered to be the adsorption of oxygen on a site containing adsorbed H2SO4. THE tendency for a metal to go into solution depends on a number of factors some of which are: 1) the position of the metal in the electrochemical series; 2) the type and concentration of corroding species in solution; 3) the concentration of oxygen in solution; 4) the type of film formed at the liquid-metal interface; and 5) the physical state of the metal. The corrosion of a metal in an aqueous solution may be considered to be a heterogeneous reaction that occurs at the liquid-metal interface. The reaction is generally considered to occur as a result of electrochemical potential differences within the system. Little work has been published in the literature concerning the corrosion of pure nickel. A great deal has been publistled dealing with the experimental and theoretical aspects of the over-all corrosion process. Evans,1 Uhlig,' and recently Todt 3 and Tomashoff,4 have published books which review the results of experiments which have been conducted on corrosion, and have developed some of the basic ideas of the more widely accepted theories of corrosion. Friend5 states that. nickel does not readily discharge hydrogen from any of the common nonoxidiz-ing acids and that a supply of some oxidizing agent is necessary for appreciable rates of corrosion. He further notes that at temperatures between atmospheric and close to boiling, corrosion rates tend to vary with concentration, temperature, and aeration in acid concentrations up to 25 pct. Whitman and Russel6 studied the effect of dissolved oxygen on a number of metals in acid solutions and found that oxygen accelerates the rate of corrosion of nickel in sulfuric acid. Flowers and Kelley7 in studying the action of dissolved CO, on electroplated nickel postulated that nickel dissolves as NiHCO3 in the presence of CO, and air. It was found that oxygen was necessary for corrosion to take place and that the rate increased with increasing amounts of oxygen in solution. Flowers and Kelley attributed the oxygen effect to cathodic depolarization. MacGillavry, Rosenbaum, and wensson' determined metal solution potentials of nickel in various electrolytes. They found that nickel has no tendency to corrode in alkaline solutions in the presence or absence of air. In acid solutions in the presence of air, metal solution potential increases in the order of 1/2 v were observed. This increase was attributed to probable chemisorption of oxygen on the nickel surface and the corrosion mechanism suggested was the interaction of H+ ions with the nickel oxide formed at the surface. Delahay9 observed the reduction of oxygen on various metals. A polarograph was used to measure the course of the reaction. With some metals hydrogen peroxide was produced as an intermediate compound. However, nickel was not considered to be a hdrogen peroxide producer. Van Rysselberghe 10,11 and associates attributed the accelerating effect of carbon dioxide on the corrosion process to the presence of percarbonic acid produced in solution reacting with the hydrogen peroxide. The percarbonic acid can be reduced at less negative potentials than hydrogen peroxide and as a result accelerates the reaction. EXPERIMENTAL Since a complete description of the apparatus used can be obtained elsewhere,12'13 no attempt will be made here to describe the equipment other than to note that it consisted essentially of an autoclave unit from which samples could be withdrawn periodically without disturbing the interior state of the autoclave. A titanium autoclave liner was used to protect the autoclave from the solution.

Jan 1, 1961

By David V. Ragone, James A. Craig, Richard E. Balzhiser

The Gibbs free energies of formation of UC2 and UC were measured by equilibrating two-phase mixtures of UC2 + C and UC, + UC with liquid bismuth. The measured equilibrium concentrations of uranium in the bismuth combined with available activity coefficient information yielded uranium activities in these two-phase regions. Measurements on UC2 were performed over the range 1015 to 1160 K and on UC over the range 1115° to 1165°K. The values obtained for UC2 are in excellent agveement with values determined using combustton calorimetry and low-temperature heat capacity measurements. The UC values are in fair agreement with the calorimetric values, differing by about 10 pct from the calorimetric determination. MUCH interest has been shown in the uranium carbides in recent years because of their potential as nuclear fuels. As nuclear reactor operating temperatures have been raised to increase thermal efficiency, new fuels have been required. The uranium carbides are of interest because of their high melting points, >2000°C, high thermal conductivity, and resistance to irradiation damage. The manufacture and use of uranium carbides are aided by a knowledge of their stability and reactivity under various conditions. In this regard the thermo-chemical properties of the carbides, i.e., heat capacity, heat of formation, free energy of formation, and so forth, are particularly important. A great amount of work has recently been done on the thermodynamics of the U-C system. Unfortunately, however, there has not been good agreement among the various investigations. This study of the free energies of formation of uranium monocarbide and uranium di-carbide in the temperature region 1100°-1200° K was undertaken to help clarify the situation. It should be noted that in the temperature range of this investigation, 1100°- 1200° K, the thermodynam-ically stable phase in equilibrium with graphite is U2C3, not UC2, Fig. 1. However, U2C3 is reported to be stable only under extremely low oxygen and nitrogen pressure. Although UC2 is metastable below 150O°C, it exists under most experimental conditions. It should also be noted that "UC," never exists as UC2 but with compositions near UC1.9. However, "UC2" will be used to designate the dicarbide phase except when the stoi-chiometry is necessary for clarity. METHOD The approach taken in this study of the free energies of formation of UC and UC2 was to determine the thermo- dynamic activities of uranium in the two-phase regions UC, + C and UC + UC, by equilibrating the two-phase mixtures with the liquid bismuth. When a mixture of solid UC2 + C is brought to equilibrium with liquid bismuth, the reaction that occurs is: Neither carbon nor UC, could be detected as dissolved material in the bismuth. The standard free energy for this reaction may be written: In the two-phase region UC, + C, Fig. 1, the thermo-dynamic activities of UC2 and carbon are unity. The activity of uranium in this region was determined by measuring the concentration of uranium in a liquid bismuth melt in equilibrium with the two-phase mixture. This concentration was then used in conjunction with the activity coefficient data of uranium in bismuth reported by Tien et al.' to determine the activity of uranium in the two-phase region, UC, + C. All of the quantities in Eq. [2] were then known, and the AG; (uc,) was evaluated. UC + UC2. For the studies involving UC + UC,, the reaction taking place when the two-phase mixture is brought to equilibrium with liquid bismuth is: The standard free-energy change for this reaction is given by:

Jan 1, 1969

By Frederick C. Pearson, Albert Brown, Emil R. Ermert

EARLY in 1946 the Shen-Penn Production Co., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenandoah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1-An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2-Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3-Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1952

By S. F. Frederick, W. A. Bailey

The relationship between microstructure and mechanical properties of cast 356-type aluminum alloys was studied to determine the cause of the variations in properties resulting from differences in solidification rate. It was found that variations in strength are a consequence of variations in ductility and that ductility is inversely proportional to the dendrite cell size. A mechanism is proposed to account for this correlation based on the fracture strain of the inter-dendritic silicon particles and the differential strain across dendrite cell boundaries. IT has long been assumed that permanent mold castings of aluminum are superior to sand castings because of their finer grain structure and reduced porosity.' A systematic variation of static properties was noted during unpublished studies of fatigue-strength variations with solidification rate of A356-T6. Of particular interest was the observation that for a given composition and heat-treatment, both ductility and the ultimate strength increased with higher solidification rate. Because the A1-Si system forms the basis of many alloys used for castings and welding wire, a study was initiated to determine the details of how higher cooling rates improved mechanical properties of these alloys. The results of this study are presented here. EXPERIMENTAL PROCEDURE Specimens were prepared from 356-T6 to supplement the A365-T6 alloy data from earlier studies. This allowed a comparison of behavior of alloys with substantially different strengths but with only small differences in alloy composition. The composition and heat treatment of both alloys are given in Table I. The specimens were cut from a chill plate casting,' which is a 6 by 9-in. plate, 1 in. thick, which has one end heavily chilled, and a large riser at the other so that solidification is essentially unidirectional from the chill end to the riser. Although not measured here, solidification times measured on similar specimens by embedded thermocouples are a few seconds at the chill end and up to 5 min near the riser. Specimens were obtained by cutting slabs from the plate, parallel to the chill; these represented different cooling rates, with essentially the same composition. For the tests, either 0.125 or 0.250-in. thick slabs were cut for standard 2-in. gage length specimens. The thicker specimens were tested to failure at 2000 lb per min while the thinner specimens were tested in an Instron machine at a constant cross-head speed of 0.02 in. per min. These thin specimens were intended for trans- mission electron microscopy. Some thin specimens were tested to failure while the remainder were given various amounts of prestrain. Dendrite cell sizes were measured by the linear intercept method on photomicrographs at either X100 or X50, depending on the cell size. It was assumed that the dendrite cells were outlined by the silicon particles. Determinations were made on two mutually perpendicular planes and an rms average taken. Electron fractographs of representative tensile specimens were made in the conventional manner using the two-stage replica technique.3 Samples for transmission electron microscopy were prepared by chemical milling followed by electropolishing. RESULTS AND DISCUSSION The results of the tensile tests and the dendrite cell-size determinations are given in Figs. 1 and 2. All data show the same trends, namely, a decrease in ultimate strength and elongation with increasing distance from the chill (and solidification time), and a corresponding increase in dendrite cell size. The yield strength remains essentially constant. The constancy of the yield strength was particularly significant since it indicated that variation in the solidification rate does not affect the stress required to initiate plastic flow. By plotting true stress-true strain curves as in Fig. 3, it can be seen that both

Jan 1, 1969

By F. W. Jessen, R. W. Durie

The development in the laboratory of mall salt cavities illustrated that the rate at which salt dissolved was affected by the rate at which fresh water was injected into the cavity. Experiments carried out with small salt cores indicated, however, that the rate of salt removal with forced convection was not significantly different from that with natural convection, provided the flow was in the laminar range. The rate of salt removal was apparently controlled by the water salinity, which was indirectly determined by the rate at which fresh water was injected. With turbulent flow at the salt surface, the rate of salt removal could be increased several-fold with the same salinity in the cavity. A quantitative evaluation of the rate of salt removal under natural convection was attempted by using techniques developed for the analogous heat convection system. The values of the rate of salt removal obtained experimentally were considerably greater than the calculated values due to surface irregularities. To determine the effect of these irregularities, the rate of salt removal was found for a smooth surface by experimentally determining the rate of salt removal as an irregular surface developed and then extrapolating this trend back to initial time. Excellent agreement between the experimental and calculated values then were obtained. INTRODUCTION Underground cavities leached from massive salt formations have been used extensively for many years for storing LPG products. The development techniques for storing methane gases in the liquid state at a low temperature leads to speculation that underground salt cavities of controlled geometry may be quite important in this field. In any case, the increasing number of salt cavities used for storage indicates an impending need for a better knowledge of the washing process to efficiently develop maximum storage volumes within specified regions. It is the purpose of this paper to discuss some aspects of -the mechanism of the dissolution of salt in the formation of cavities of controlled geometry. Although no attempt is made to resolve the problems that may be associated with the storage of methane in the liquid state in salt formations, the fact that salt cavities can be formed at reasonable cost would appear to justify investigation in this direction. Further, underground cavities have the advantage of allowing storage at higher pressures (and hence higher temperatures) than surface installations. Although the thermal conductivity of salt is somewhat higher than frozen earths, 0.017 cal/(sec) (cm)(c) for salt at 32F vs 0.005 cal/(sec) (cm) () for ice at this temperature, this disadvantage is offset by the higher storage temperature in underground cavities. For example, at atmospheric pressure, the temperature of liquid methane would be —258F. In a storage cavity at 2,000 ft, the pressure would be approximately 1,000 psia, which would allow a storage temperature of -9OF. The formation temperature would be roughly 110F at this depth, hence the total temperature differential would be 200F. Under surface storage conditions the corresponding temperature difference would be some 333 F (75 F + 258 F). The results of this difference can be compared more readily by substituting the appropriate values of thermal conductivity, temperature difference, heat capacity and density into the solution of the diffusion equation for the unsteady linear conduction of heat. For the underground salt storage, the heat flux is 15cal/(sec) (sq cm), where t is the time in seconds from the initiation of the cooling. For the surface system, and using the thermal properties of ice at the average temperature, the corresponding figure is 21cal/(sec) (sq cm). Hence, the heat losses through ice under surface conditions would be some 30 per cent higher than the underground salt storage. This ratio would vary, considerablv. Of course, for other conditions, but it indicates that an advantage over surface facilities may be obtained by storage in underground salt cavities.

Jan 1, 1965

By E. S. Machlin, C. W. Chen

RECENTLY Chen and Machlin' proposed a mechanism for intercrystalline cracking in metals during high-temperature stressing. According to this mechanism the formation of voids at grain boundaries is primarily responsible for intercrystalline cracking. A model has been provided to demonstrate the initiation of submicroscopic cracks and voids at jogs of grain boundaries where grain boundary sliding is inhibited. Submicroscopic cracks can grow as a result of either further grain boundary sliding or localized tensile stress. In the former case, it is believed that grain boundary sliding produces more voids which link together to produce macroscopic cracks and which may lead to the eventual failure of the metal. Concurrently, Nield and Quarrell2 reported their interesting results obtained in a systematic investigation of intercrystalline cracking in two aluminum alloys under various creep conditions. Their observations are generally in agreement with the above mechanism, especially the conclusion that voids are formed as a direct consequence of grain boundary sliding. On the basis of the volume fraction occupied by voids, they could find no confirmation of vacancy condensation as the mechanism for void growth. Furthermore, an important feature of intercrystalline cracking has been likewise pointed out by them that the majority of cracks are not formed at grain corners. Nield and Quarrel1 meanwhile emphasized the importance of grain boundary migration by designating it as one of two main processes operative in the mechanism of crack formation during creep. The designation seems unnecessary because overemphasis of grain boundary migration only complicates the mechanism of void formation. There are two reasons which militate against the inclusion of grain boundary migration in the mechanism of void formation. In the first place, the formation of intercrystalline voids per se does not require grain boundary migration. Secondly, in addition to grain boundary migration, void formation may be minimized by any other process such as plastic deformation which is capable of relieving localized stresses around jogs. Chang and Grant3 have shown that intercrystalline cracking is prevented in aluminum by lattice bending in high stress regions. The influential role played by grain boundary migration in creep has also been realized in our studies. In several cases, voids did not appear at all in grain boundaries whenever grain boundary migration took place prominently during creep. The purpose of this paper is to discuss the effect of grain boundary migration on the formation of intercrystalline voids and other related rupture properties. Experimental evidence indicates that in an unstable grain structure void formation may be markedly modified by structural changes. The abnormally high ductility and the transcrystalline mode of fracture observed in copper at elevated temperatures reveals that effective grain boundary migration minimizes void formation. Grain boundary migration has long been known as a common high-temperature phenomenon in metals with the grain configuration in a nonequilibrium state. Its effect on ductility and mode of fracture has not been recognized until recently.4 Since the introduction of the term "Equicohesive Temperature," the conventional belief has been that below the equicohesive temperature the ductility of metals increases moderately with decreasing temperature until the ductile-to-brittle transition temperature of fracture is reached. In this temperature range, metals fracture in a ductile mode with a "cup-and-cone" fracture surface. Above the equicohesive temperature, ductility remains invariably low and decreases slightly with increasing temperature. The mode of fracture is strictly brittle and intercrystalline. Typical examples have been shown for a brass and copper in Fig. 1 and 9, respectively, in the paper by Greenwood, Miller, and Suiter.5 The observation in the upper temperature range that ductility of metals is low and insensitive to temperature may be explained in terms of void formation at grain boundaries. It is also in accordance with the findings of McLean6 and Fazen, Sherby, and Dorn7

Jan 1, 1961

By L. Burris, C. H. Stockman, I. G. Dillion

Zone melting is a purification process in which separation of impurities is effected by slowly moving a narrow melted zone through a bar of solid material. Equations are presented which 1—predict the concentration profiles after successive passes of the zone and 2—give the limiting distribution of solute along the bar after an infinite number of passes of the molten zone. These equations take into account the effect of normal freezing in the last zone length. These equations were solved numerically using an electronic computer, and the concentration profiles are presented as a function of the solute distribution coefficient and the ratio of molten zone to total bar length. ZONE MELTING is a purification process in which separation of impurities is effected by slowly moving a narrow melted zone through a bar of solid material. Separation occurs if the solid freezing from a solution at any moment has a composition different from that of the liquid from which it is freezing. Solutes which lower the freezing point will tend to remain in solution and will be moved in the direction of zone travel. Solutes which raise the freezing point will preferentially freeze out, and they will be moved in a direction opposite to that of zone travel. After repeated unidirectional passage of a molten zone through a bar of material, impurities will be concentrated in the ends of the bar. A limiting concentration gradient will be reached in the bar after a large number of passes of the molten zone. Both the magnitude of this limiting concentration gradient and the rate of movement of solute in any pass depend on the zone length and on the equilibrium concentrations of solute in the liquid and solid phases. The basic theory of zone melting was thoroughly covered by Pfann.1 The purpose of this paper is to extend the theory of zone melting by presenting 1—equations which relate the concentration profiles in successive passes of the zone and 2—equations which give the limiting distribution of solute along the bar after an infinite number of passes of the molten zone. These equations take into account the effect of normal freezing* in the last zone length concentration of a given solute in the solid to the concentration of the same solute in the liquid. Analytical methods for determining the concentration profiles after any pass have been developed by Lord2 and Reiss. The method developed by Lord does not take into account normal freezing in the last zone and also becomes very complicated when the number of passes becomes large. The method developed by Reiss enables the direct calculation of the complete concentration profiles (including that in the last zone) after any pass for values of k close to unity (0.9 < k < 1.1). Both methods are useful and provide valuable insight into the zone melting process. The equations given in this article are based on the same assumptions used by Pfann. These are: 1—uniform composition in the liquid, 2—negligible diffusion in the solid, 3—constant distribution coefficient, 4—constant length of the liquid zone (except at the ends), and 5—solubility of the solute in the melt is not exceeded at any point. Equations for Concentrations in Successive Passes For a melted zone of length 1 at the left-hand end of a bar of uniform unit cross-section, the amount of solute in the liquid is J0Cn-1(x) dx [1] where the subscript is the number of the pass. Cn-1(x) represents the concentration (expressed as weight per unit volume) obtained in the previous

Jan 1, 1956

By J. W. Downey, R. A. Morris, M. V. Nevitt

An experimental survey has determined the occurrence of Ti2 Ni-type phases in binary and ternary alloys of Ti, Zr, or Hf with first, second, or third long-period transition metals and also in ternary systems in which 0 is the third component. The existence of eleven previously unreported isomorphs is cited and some approximate phase boundaries are given. Lattice parameters are reported for the new phases. The periodic table relationships involved in the occurrence of the phase are discussed. A previous paper&apos; reported the occurrence of a group of Ti2Ni-type phases (structure-type E93) containing Zr in combination with Rh, Ir, and Pt, and Hf in combination with Rh, Pd, Ir, and Pt, and cited evidence to show that all of the Zr phases and the Hf-Pd phase are not binary phases but occur only when 0 is present. More recently one of the present authors found that in the ternary systems of Ti and 0 with Cr, Mn, Fe, Co, and Ni the occurrence of the Ti2Ni-type phase could be correlated qualitatively with valency electron concentration, and that the role of 0 appeared to be that of an electron acceptor.&apos; This paper describes the results of a broader investigation of the occurrence of Ti2Ni-type phases in binary and ternary systems containing Ti, Zr, or Hf. EXPERIMENTAL PROCEDURE Alloys were prepared by arc melting. The purity of the metals Zr, Rh, Hf, Ir, Pd, and Pt was given in the previous paper.&apos; The additional materials used for this work were metals with a minimum purity of 99.9 pct and reagent grade ZrO2, TiO2, Cr2O3, and NiO. Chemical analysis of several alloys in each system indicated good agreement between intended compositions and cast-button compositions. For the heat treatment precautions were taken to avoid oxygen contamination. The specimens were wrapped in Mo foil and sealed in fused quartz tubes at a room temperature pressure of 1 x mm of Hg. These capsules were then annealed in a vacuum furnace at an external pressure of 5 X mm of Hg. Since the major constituent in most of the alloys studied was the brittle Ti2Ni-type phase, Debye-Scherrer patterns with sharp lines could be obtained with powder crushed from the annealed solid samples without being reannealed. Metallographic, X-ray diffraction, and density determination techniques previously described1, 2 were used. RESULTS AND DISCUSSION Zr-Rh-O, Zr-Ir-Oand Zr-Pt-O Systems-Figs. 1 through 3 show the approximate boundaries of the Ti2Ni-type phase fields at the temperatures indicated in the ternary systems Zr-Rh-O, Zr-Ir-O and Zr-Pt-0. In each isothermal section the Ti2Ni-type phase field is labeled E and the unidentified binary phase found in the previous work&apos; is labeled ?. The dotted lines, which are not phase boundaries, correspond to the composition (Zr2 B)1-xOx. In each system the Ti2Ni-type phase field is displaced to the high-Zr side of this composition line. However, the departures from Zr2B stoichiometry for the metal components are not as high as Zr3B, as was inferred from the previous work. Lattice parameters of the Ti2Ni-type phases in the alloys shown as triangular data points in Figs. 1 through 3 are given in Table IA. The probable compositions of the Ti2Ni-type phases have been estimated from the isothermal sections. Although there are a few exceptions that probably result from uncertainties in phase boundary location and from the effect of variation of oxygen content, the generalization can be

Jan 1, 1961

By Fredrick C. Pearson, Albert Brown, Emil R. Ermert

EARLY in 1946 the Shen-Penn Production CO., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenan-doah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,-000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1—An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2—Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3—Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1953

By Albert Brown, Emil R. Ermert, Fredrick C. Pearson

EARLY in 1946 the Shen-Penn Production CO., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenan-doah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,-000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1—An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2—Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3—Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1953

By Frank J. Tolonen, Nicholas H. Manderfield, Paul Jasberg

EARLY in the study of the low grade iron formations of Michigan, wide variations in their structure and texture became evident. Because of these variations no simple method of concentration is possible, and those portions of the formations that can be exploited profitably under a given stage of metallurgical progress and existing economic conditions must be searched for carefully. Both structure and texture of the formations have an important bearing on their amenability to bene-ficiation. By structure is meant the banding planes of easy fracture, the porosity, and the degree of leaching. Texture, which includes grain sizes, shapes, and degree of interlocking, determines the amount of grinding necessary to liberate the mineral grains. Structure determines the liberation of portions richer in one mineral. Structure and texture may be termed the gross features of the formation. Earliest surveys of the formations were conducted to outline the parts that could be concentrated at % in. (3 mesh). Operators agreed on this size because anything finer required sintering or other agglomeration processes. At 3 mesh only the structural features, as defined above, would be liberated. With suitable ores concentration was easy, as any of the gravity methods could be used. Sink-and-float gave good results, but with this method only limited portions of the iron formations yielded a desilrable product.1,2 n general, the iroa content could be raised to shipping grade, but the silica content remained too high—sometimes 20 pct—instead of 9 or 10 pct. Grinding did not greatly increase the liberation ofsilica until 2010 mesh or finer was reached. To find the reason fpr this T. M. Broderick began micros~opic examin&apos;ations of the formations in 1933.3 Procedure: The purpose of this discussion is to correlate the appearance of typical portions of the iron formations with their amenability to concentration. As liberation is essential before separation becomes possible, much of the work is based on measuring the liberation achieved by crushing and grinding. Both heavy media and magnetic tube tests were used in this work. On the basis of general structural features such as banding, degree of alteration, and leaching, a specimen was selected from each part of the iron formations studied. The specimen represents the gross features of the formation and not necessarily the particular formation quantitatively. One half of the specimen was polished for macro-study, and the remainder was used for analyses to obtain the grades represented by variations appearing in the macrosection. Specimens for microscopic examination were also prepared for each variation in gross appearance. For correlation of microstructure with liberation, the previous work by sink-and-float methods was supplemented by magnetizing roasting followed by magnetic separation. The results show the liberation of silica to be very important at the sizes used, because any silica particle with iron minerals occluded would be held in the concentrate. A magnetizing roast changes the crushing and grinding character of the sample. For partly leached soft samples the change is slight, but with harder types and those in which there is a considerable change in crystal structure of the minerals, the increase in liberation of the iron minerals may be 30 pct more than that of unroasted samples at the same crusheH size. Gogebic Range Iron Formations: The Gogebic Iron Range is located in the extreme western and southern parts of Michigan&apos;s Upper Peninsula, extending westward into Wisconsin. Samples for this study were obtained from the Ironwood formation, comprising three chief members—the Plymouth, Norrie, and Ahvil—with several intermediate slates and thick overlying slates. (The slates are not considered in this discussion because grinding finer than present practice is usually required to liberate the iron minerals.) The predominant iron mineral is hematite, about half of which is hydrated to goe-thite. Limonite occurs in some of the partly leached areas, and siderite in parts of the formation.

Jan 1, 1958

By Heribert Wiedemeier, Ali Khan

The tetnperature-conposition phase diagram of the syste,n MnS-CdS has been investigated over a range fro)n 600° to 1000° C. The small degree of solid solution on the MnS rich slde cornpared to the large CdS rich single-plzase region could be esplained by the difference in strzrctures of the cotnponents and the relative sizes of the metal ions. The change in lattice parameter as a function of cot)zposition is linear atzd jollous Vegavd&apos;s rule within experittzental limits of error. Mns and CdS have gained considerable attention in recent years because of their interesting solid state properties. In order to investigate such properties and thermodynamic quantities of mixed compositions of transition metal chalcogenides, it is necessary to establish their phase diagrams. Two earlier publications are concerned with the MnS-CdS system. Schnaase&apos; found complete miscibility when MnS and CdS were co-precipitated in aqueous solutions at room temperature. However, there is evidence that the mixed crystals were not stable over the entire range of composition. roger&apos;s&apos; investigation of the ternary system ZnS-CdS-MnS at 900" C indicates a solution of 48 mole pct MnS in CdS. During the course of this work which covers a temperature range from 600" to 100O° C, emphasis has been placed on the use of high-purity materials and well-defined modifications of starting products. EXPERIMENTAL Starting Materials. The stable green modification of MnS with NaCl structure was prepared by direct fusion of the elements and by chemical transport reaction. Stoichiometric amounts of manganese of 99.99+ pct purity and of sulfur of 99.999 pct purity from Gallard-Schlesinger Corp. were sealed in an evacuated quartz tube at a pressure of 10"5 mm Hg and annealed for 48 to 60 hr at 800°C. The quartz tubes used throughout this work were outgassed under high vacuum at a temperature of 90OU to 1000° C for 12 to 18 hr. For the synthesis of MnS by chemical transport3 stoichiometric ratios of elemental manganese and sulfur and small amounts of iodine were sealed under vacuum in a quartz tube, which was placed in the temperature gradient, 900/800-C, of a two zone furnace. Single crystals of MnS in form of platelets and octahedra were deposited at the cooler end of the tube. The manganese content was determined by EDTA titratin. A typical result of several analyses was 63.05 pct Mn which agreed well with the computed value, 63.14 pct. Commercially available CdS of 99.9+ pct purity, a mixture of the cubic and hexagonal forms, was converted into the hexagonal high-temperature modification by annealing CdS under vacuum in quartz tubes at 700° C for about 36 hr. As a second method, cadmium sulfide was transported in a temperature gradient, 70O° /650" C, with in vacuo sublimed iodine from the hot to the cooler zone of the tube. Large sized crystals in form of hexagonal columns and some platelets were obtained. An average result of the cadmium analysis by EDTA titration4 was 77.93 pct in good agreement with the computed value, 77.81 pct. Only the NaCl modification of MnS and the wurtzite modification of CdS were used for the solid solutions. Preparation of Solid Solutions. Finely powdered MnS and CdS samples were thoroughly mixed in molar ratios and compressed into pellets of about 6 mm diam and 2 mm in height at a pressure of approximately 13,500 atm.

Jan 1, 1969

By M. van Swaay, C. E. Birchenall

A. S. lBrling (Johnson, Matthey & Co. Ltd., Laboratories)— Because of its initial emphasis upon the production of membranes by powder metallurgy and by normal casting and rolling techniques, this paper is of considerable interest to those concerned with the design and application of industrial diffusion units. As the subsequent performances of the three grades of palladium were not compared in detail, it can perhaps be concluded that specific permeabilities were very similar. A short table in which the absolute diffusion rates obtained by the Authors with their three grades of palladium were compared with those of other investigators18-25 would, however, have been of particular value in view of the very variable results obtained with this membrane material. The Authors state early in the paper that the permeability of the thoriated samples decreased in much the same way as that of the nonthoriated samples. Later, they emphasize that sintered palladium without thoria was very susceptible to poisoning and did not respond as well as the other materials to the decontamination treatment. These results, which suggest that sintered membranes are less effective than those produced by normal methods, have considerable industrial implications, and amplified experimental details would be very welcome. The results of the Authors differ in one important respect from those of other investigators. Thus, no "bleeding" was required to maintain a constant rate of diffusion, although Davis, Darling, and De Rosset found this to be necessary. Davisz3 found that "bleeding" was necessary even when the hydrogen had already been purified by diffusion through a palladium tube, and it would be of value to know the purity of the gas stream emerging from the purification train shown on Fig. 1 of the Authors&apos; paper. The Authors show that diffusion rates varied according to the square root of the pressure difference providing that the palladium membrane was not contaminated in any way. This finding is in agreement with the results of those workers2,18,19,23,24 who diffused their hydrogen through the membrane into a partly or completely evacuated system.Those workers who did not find this square-root law dependence did not have a partial vacuum on the downstream-side of the membrane.&apos;&apos; The difference between the two experimental con- ditions appears to be significant, as the absolute diffusion rates per sq cm of diffusion area are lower when the square-root law dependence is not observed. While the effect could be attributable to poisoning of the membrane it is conceivable that a positive pressure on the downstream side of the membrane might influence the mechanism of diffusion. In view of the capricious behavior of palladium, factors of this type, which are likely to influence its industrial significance, should be carefully considered. M. van Swaay and C. E. Birchenall (authors&apos; 9-eply) — Our Eq. 191 may be compared with several others for hydrogen diffusion in palladium: D = 5.95 x exp (-5770/1)&apos; D = 3.55 x 10"3 exp (-5550/)&apos; D = 4.3 x 10"3 exp (-5620/1&apos;)&apos; Other values are given in the literature, but in many cases surface poisoning may have affected the results. No analysis was performed on the hydrogen gas stream after purification. It should be noted that the presence of liquid nitrogen traps near the heated membranes may have set up convection currents and provided the equivalent of "bleeding." The question of whether a partial vacuum existed on the downstream side of the membrane is not clear. Does it imply that there is something unique about the permeability measured near one atmosphere pressure? We do not believe that there is. When square root pressure dependence is not observed, diffusion rates are not measured. Is "absolute diffusion rate per sq. cm. of diffusion area" equivalent to permeability? The terminology is new to us. In any case we doubt very much that pressures of the order of several atmospheres can affect the mechanism of diffusion.

Jan 1, 1962

By Roland de Wit

Conclusions reached in a paper by weertmanl are amplified in a mathematical and graphical way. It is shown that in a stressed crystal a straight dis-location may be in a position of unstable equilibrium with respect to helix development, and how a small perturbation may start the dislocation off on its helical path. Helix development occurs by diffision; bulk diffusion is necessary for development from a screw, but core diffision is sufficient for development from an edge dislocation. For a mixed dislocation helix development can take place by core diffusion if the helix also climbs; a diffusion reversal takes place when the slope of the helix equals the slope of the Burgers vector. The work done on a crystal by the external forces is graphically shown to be consistent with the direction of motion of the dislocation in helix development. Finally a detailed mechanism for tangle formation from helices is presented. In the course of helix development a glide situation may be reached where a segment of each helix loop lies in a slip plane in which it can expand by glide. Thus is it visualized how a helix can deteriorate into a tangle. A paper by weertmanl proposes dislocation-tangle formation by a helical dislocation mechanism. The present paper amplifies Weertman&apos;s arguments in a mathematical and graphical way and presents some further ramifications of the proposed model. The importance of dislocation tangles is discussed in Weertman&apos;s paper and the references cited therein. The mechanism of their formation is not yet understood. Weertman proposes that in cold-worked crystals conditions exist suitable for the conversion of straight dislocations into helices and subsequently into tangles. Helix formation occurs by a diffusion process and Weertman proposes that at low temperatures only core diffusion is important. The present paper necessarily repeats some of Weertman&apos;s work. Since the mathematical development and notation used are slightly different from his, this was thought necessary for clarity. GEOMETRY OF THE HELIX weertman2 has shown that the equilibrium form of any dislocation line is a helix if it is assumed that the energy per unit length (line tension) of the dis- location is constant. For the special case that no external forces act on the dislocation, the helix reduces to a straight line. We shall assume in this paper that the dislocation has a helical form even when it is not in equilibrium. The parametric equation of a helix is, see Fig. l: where a is the radius of the cylinder tangent to the helix, and 270 the pitch of the helix. The pitch is related to v, the number of turns per unit length (along the axis) by the relation: When a = 0 Eq. [I] gives a straight line in the z direction. The growth of a straight dislocation into a helix is now described mathematically by letting a vary from zero to its final value. The tangent to the helix is given by where is the path length along the helix. This gives the direction of t and since its magnitude is unity we must have So that dcp/ds = (a2 +p2)-"&apos;. The curvature of the helix is given by where n = -(cos + sin) is a unit vector normal to the helix. Note that the vectors k and n always point toward the axis of the helix, Fig. 1. FORCE ON THE HELIX The external force which makes the straight dis-

Jan 1, 1963

By R. A. Greenkorn, R. C. Smith

Hele-Shaw cells are used to model creeping flow through porous media (where Darcy&apos;s law is valid). The effects of inertia on flow about obstructions in a Hele-Shaw cell can be calculated by a perturbation method if one can determine a solution to Laplace&apos;s equation. Results of a computer solution for flow about circular, square and elliptical obstructions are presented. These results show that or a modified Reynolds number of less than I, the inertia terms are small; and for values of less than 3, the average streamline predicts the ideal flow. Therefore, the analogy might be used for studying flow in porous media up to a modified Reynolds number of at least 3. INTRODUCTION The nature of fluid flow in porous media is of interest in the fields of soil mechanics, ground water flow, petroleum production, filtration and flow in packed beds. Because it is very difficult to study the phenomenological behavior of flow in porous media, homologs and analogs are used to study flow characteristics. A Hele-Shaw model, made of two closely spaced plates - usually glass — is often used as an analogy to two-dimensional flow in porous media. Hele-Shaw2 showed experimentally that the streamline configuration for creeping flow around an obstacle located between two closely spaced parallel plates is the same as for two-dimensional, ideal flow about the same obstacle. Stokes7 verified these observations mathematically. The usual equation of motion for flow in porous media is Darcy&apos;s law. The form of the mathematical statement of Darcy&apos;s law is identical, within a multiplicative constant, to the expression for the average velocity over the plate gap in the plane of a Hele-Shaw model. These models may be used to describe flow in both homogeneous and heterogeneous porous media. In the mathematical proof of the Hele-Shaw analogy it is assumed that the convective terms in the Navier-Stokes equations are negligible and that the equations of motion degenerate to Laplace&apos;s equation, with pressure the dependent variable. Whenever a Hele-Shaw model is used as an analogy to flow in porous media, .the validity of this assumption is in question. Riegels5 showed that if convection is not neglected, the velocity distribution around a cylindrical obstruction in the flow field depends on a Reynolds number, the plate spacing, and a dimension characteristic of the obstacle. Riegels&apos; solution, a perturbation solution, uses the boundary condition that the flow rate into the obstacle averaged over the plate gap at any point on the obstacle is zero. The method requires that a solution to Poisson&apos;s equation for the perturbation pressure be found. Riegels evaluated this solution for the case of the cylindrical obstruction. His method may be simplified by eliminating the need for solving Poisson&apos;s equation for the perturbation pressure. Instead, an analytic expression for the perturbation pressure gradient is obtained (valid for arbitrary shapes) and used to eliminate pressure from the equations for the perturbation velocities. The results show, for symmetrical shapes, that if NRe < 1, the convective acceleration terms are small, and that the average velocities represent ideal flow up to at least NRe = 3, where: L is a characteristic dimension of the obstacle perpendicular to flow, b is the plate spacing, u is viscosity, v, is velocity of approach and p is density. THEORY* Incompressible fluid flow through a Hele-Shaw model and a porous medium are analogous because the equations for the average velocity components in two-dimensional flow are identical if:

Jan 1, 1970

By R. D. Young, E. A. Harre

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth&apos;s atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Certain bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent required by succeeding nonleguminous crops. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. These organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen at high temperatures and pressures and in the presence of a catalyst to form ammonia. Modern plants use air, water, and natural gas or other hydrogen sources to produce the ammonia that is now the key building block of the fixed nitrogen industry. Several major problems that developed in the 1970s continue with the nitrogen industry into the 1980s. These are (1) the continuing sharp escalation in the cost of feedstocks for ammonia production as well as all energy sources, and (2) the very steep increase in the investment cost of production facilities. More than 75% of the fixed nitrogen produced domestically is consumed as fertilizers. The types of materials used as fertilizers have changed significantly during the past years. There has been a trend from the use of low-analysis fertilizers to types which contain high percentages of plant nutrients. The average plant nutrient content (N + P2O5 + K2O) of fertilizers used in the United States has increased from 18% in 1930 to 32% in 1960 and today approaches an average of 44%. In the case of nitrogen fertilizers, the low analysis natural nitrates (16% N) gave way to ammonium sulfate (20% N) after about 1920. After World War II, ammonium nitrate (33.5% N) previously used in munitions, became established as the leading nitrogen fertilizer. Urea use as a fertilizer (46% N) began in the 1960s, and in the past 10 years has become the world&apos;s leading solid nitrogen fertilizer. Nitrogen Materials Anhydrous Ammonia-Anhydrous ammonia is a colorless gas at ambient temperatures and pressures and has a sharp pungent odor. Anhydrous ammonia is stored and transported as a liquid in high-pressure cylinders and tanks at ambient temperature, and in low-pressure tanks, barges, and ships at -28°F. Anhydrous ammonia is applied directly at 4 to 7-in. depths in the soil as a high-pressure liquid by special applicators, after which it expands to a gas that dissolves in the soil moisture or is absorbed on soil colloids. In other systems ammonia is metered into irrigation water and is thereby introduced into the soil.

Jan 1, 1983