Search Documents

By M. Albertson

AT Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin' Was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 in.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 in.), the width at the lower lobe was about. 1000 ft., and the, width at the narrows probably. 400 to 500 ft. The original depth of water varied from 20, to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft.. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the. lake. About

Jan 2, 1921

By Frank Firmstone

The furnace from which the brick here referred to were taken, was lined under my supervision and blown-in in May, 1902. It was 75 ft. high and 18 ft. in greatest diameter, and used coke to smelt a lean magnetic iron-ore. The lining was put in as follows:—First, blocks 14 in. long by 6 in. thick; second, 2 in. of loam; third, 13.5 in. of 9-in. fire-brick (one-and-ahalf brick wall) laid in English bond; fourth, red brick to within 2 in. of the iron shell; and fifth, 2 in. of slag-wool between the red brick and the shell. The brand of brick used has been known to me for over 20 years, and in my observation had always proved very durable, notably when used in a small furnace 50 k. high which treated the same magnetic. ore. On revisiting and examining the furnace in March, 1903, it was found that the whole of the lining of 14in. blocks at the top, and for an unknown distance (more than 20 ft.) below, had completely disappeared; and a few weeks later the 13.5-in. lining and the red brick at the top likewise vanished, and the furnace was blown out. N~twithstanding the complete failure of the lining higher up, measurements taken after blowing-out showed no unusual wear in the lower part of the furnace. The exact position in the furnace of the piece of brick-work used in the analysis, given below, is not known; but it came from between 30 and 40 ft. above the bottom. It had formed part of the 13.5-in. wall (no 14-in. brick remaining at that level) and consisted of parts of several bricks so firmly sintered together that fracture occurred indifferently through the joints and through the body of the brick. The joints could, however, be traced by a close examination. The surface which had been in contact with the material in the furnace was covered with a yellowish, translucent glaze, somewhat vesicular, and from

Jan 1, 1904

By E. Gaujot

IN connection with the question of coal waste and economy in mining, we would call the attention of those interested to an apparatus invented by M. Dernencourt, Superintendent of the Anzin Division of the Anzin Coal Company, North of France. This apparatus is known in France and Belgium under the name of prop screw-jack (vis botte), and has been used with good results in the above-named countries for some years past. M. Ponson gives, in his " Trait6 de I'exploitation des Mines," a description of it (page 533), but as the description given is old, the work not widely known in this country, and as some valuable improvements have been made since, I thought it might be useful to give a description of it, having seen it in 'operation in 1867, while in Europe to attend the great Exposition, and on a scientific tour to the mining districts of France, Germany, Belgium, and Italy. The prop screw-jack is composed of the following pieces : I. The body or column B, Fig. 4 [Plate (I)], of oak or yellow pine, sawed square, the bark taken off, and any length, proportionate to the vein. The smallest are 10 inches diameter at the base, and 9 inches at the top, the height being from 12 to 15 inches less than the size of the vein. In the axis of this column, and at the top end, is a cylindrical opening or hole, C, 22 inches diameter, 10 inches deep, for the screw, S. II. Two wrought-iron rings, R R, to strengthen the two extremities of the column ; the rings must be put on hot. III. A cast,-iron washer, E, with hole in centre a little larger than the screw, to be put on the top of the column, and on which the nut is to rest; the top side of this washer must be faced on the lathe, also the bottom of the nut, to prevent friction. IV. The screw, S, having a total length of 12 inches and a diameter of 24 inches (for very high veins this diameter may be increased to 3 inches), and has on its top a wrought-iron plate, T,

By J. A. Solomon, H. E. Shafer

As a result of the great demand for metallic aluminum and the scarcity of domestic bauxite, numerous processes have been proposed and developed to extract the oxide of this metal (Al2o3) from clays, shales, and other low-grade raw materials.1-4 An exploratory study was made to extract alumina with sulfuric acid from relatively impure coal-associated draw-slate and to establish an optimum calcination temperature for maximum recovery. Draw-slate is the term used to describe the hard, slaty material directly overlying many coal seams and may range from a few inches to a few feet in thickness. Alumina content of these draw-slates may range from as low as 15% to over 35%. Although the following results are limited in scope, some of the data should prove beneficial for further work. Coal-associated clay, shale, and gob heretofore have been considered nuisance products; any successful alumina extraction process would greatly enhance the worth of these almost limitless resources. This research demonstrated that an optimum calcination temperature for alumina extraction could be established for a coal-associated draw-slate and that this temperature was lower than those suggested in previous work with unspecified clay types. It should be noted that slightly higher acid concentrations and somewhat finer particle sizes were used in this series of tests as compared to previous work. EXPERIMENTAL WORK Essentially, alumina extraction proceeded in four steps: 1) grinding, 2) calcining, 3) acid leaching, and 4) precipitating of aluminum sulfate. An initial series of reference tests to determine the optimum temperature of solubility for alumina was run using relatively pure kaolin. Kaolin forming clays are hydrous aluminum silicates of the approximate composition 2H2O A12O3 2SiO and kaolinite is the mineral that predominates in most kaolins. 5 The kaolin was ground to -30 mesh and subsequently calcined at temperatures ranging from 100°C to 700°C. Each sample was calcined for 1 hr in a muffle furnace and in turn subjected to sulfuric-acid leaching (H2SO4, 9 molar) for a 2-hr period. The filtrates were analyzed for the amount of dissolved alumina recovered.637 Also, each sample of leached or barren residue was

Jan 1, 1968

By T. Egleston

AT the Dover meeting of the Institute, Mr. F. A. Canfield showed some of the members a machine which he had invented for dressing mineralogical and geological specimens, which he has since modified and brought to such a high state of perfection, that after having used it for several months in preparing specimens for the cabinet of the

Jan 1, 1876

By T. Egleston

At the Dover meeting of the Institute, Mr. F. A. Canfield showed some of the members a machine which he had invented for dressing mineralogical and geological specimens, which he has since modified and brought to such a high state of perfection, that after having used it for several months in preparing specimens for the cabinet of the

J. Lainson Wills, Ottawa, Can. (Communication to the Secretary) : The localities of the Quebec and Ontario apatite deposits, and the nature of their occurrence haye been often described in the Transactions and in other publications that are readily available, and I do not, therefore, intend to discuss the many details advanced in Mr. Small's paper beyond the following two points:

Jan 1, 1893

Reserves of Lake Superior Manganiferous Iron Ores Appendix-to paper by CARL ZAPFFE, presented at the Cleveland Meeting and issued, as Pamphlet No. 1664-C, with MINING AND METALLURGY, May, 1927. The author has made several test calculations on the basis of manganese units that are and may be involved. These are summarized here, as follows: On the basis of ore produced since 1902, the average annual requirement of manganese units would be 91,000 tons; on the basis of the production of the past 4 or 5 years, the requirement would be 145,000 tons; on the basis of the year 1925 only, the requirement would be 155,000 tons. Applying the percentage of increase for the next 20 years, as determined by the plat shown as Fig. 3, the total requirement for 20 years would be 3,254,000 to 3,572,000 tons, if one used either 145,000 tons or 155,000 tons as a starting point. We have the following interesting facts: (1) The Michigan ores contain only about one-half the manganese that the Cuyuna ore does; (2) the Cuyuna district now produces one-half the ore required; (3) the known tonnage of Cuyuna reserves is greater than the speculative reserve offered for Michigan; (4) at the present rate of production considered by tons, Michigan ores ought to be exhausted in 20 years or less while Cuyuna ores would last up to 44 years. We should now reduce the estimated reserves to a basis of manganese, units. Using the tonnages listed in Combinations 2, 3, 4 and 5, the reserves total 3,118,225 tons, 3,781,995 tons, 5,041,995 tons and 5,560,342 tons, respectively. Therefore, needing at the most 3,572,000 tons, as shown above, either Combination 3, 4 or 5 will not only suffice but will leave an excess-enough for 1 or 2 years for Combination 3, 9 or 10 years for Combination 4, and 12' to 13 years for Combination 5. This means that for Combination 5, without using tonnages obtained from beneficiating or from mixing poor ores, the reserves are ample for about 33 years.

Jan 5, 1927

By Everett Carpenter

THE average daily production of crude oil-in Kansas a1 the beginning of the year was about 71,000 1 bbl. and, at its close, 82,000 bbl.-an increase of 11,000 bbl. per day. The total production for the state during the year was about 28,250,000 bbl., or an average of practically 77,500 bbl. per day for the year. This increase in the production was the result of the discovery of several new pools of high-grade oil. COWLEY AND SUMNER COUNTIES One of the principal factors in bringing the production of the. state back to its former level was the newly discovered pools in western Cowley County. During December, 1923, the Waite Phillips Co. completed its Johnson No. 1 in Sec. 20, T. 33 S., R. 3 E., which opened up the Rainbow pool about 12 miles southwest of Winfield. In this pool, the production comes from the Burbank sand, locally called the "Rainbow," found at a depth of 3200 ft. The sand varies in thickness from 25 to 40 ft. in the seventeen wells completed during the year, and the initial productions ranged from 300 to 3000 bbl. per day of 40° Be. oil. The Rainbow pool is purely a wildcat discovery, for no. rocks suitable for the use of the geologist are present. To determine the geologic conditions, the larger companies core-drilled the Rainbow area immediately after the discovery. The Marland Refining, Co., drilling on the Graham farm in Sec. 9, T. 33, R. 3, failed to find the Burbank sand and continued to the Siliceous lime, often erroneously called the Wilcox, at 3505 ft., where a well with an initial production of 900 bbl. of 40 Be. oil was obtained. In the development following this discovery, 4 additional wells were completed, 3 of which encountered pay sand at 2500 ft., the initial productions each being about 200 barrels. Judging by the sands already proved and the area indicated as probably oil bearing by the development to date, these pools have a very promising outlook for the future. It is not unlikely that a field second only to El Dorado may have been opened.

Jan 3, 1925

By J. E. Schaefer

A summary of oil and gas development in Ohio for 1936 is necessarily brief and, in some details incomplete, owing to the lack of a central state agency for the collection of data and statistics on well drilling and production. The information used in this report was compiled from the records of the several companies operating in the state. Drilling activity in Ohio increased during 1936 as compared to the two preceding years. During the year 1157 wells were completed, as compared to 1022 wells in 1935 and 1055 wells in 1934. However, in spite of this increase in drilling activity, both oil and gas production declined for the year. Activity by Fields Trenton Sand Field.—The Trenton sand field is located in 15 counties of northwestern Ohio, trending from Toledo on the north, south and west through Findlay into Indiana. About 40 years ago the Trenton field was one of the most important oil-producing fields in the United States, but it has declined to a position of minor importance. During the year 1936 there were 52 completions in this field—29 gas wells, 19 oil wells and 4 dry holes. Clinton Sand Field.—The Clinton sand is by far the most important gas-producing field in the state. Production is located in small pools separated by nonproducing areas, on a band of varying width reaching from Cleveland on the north to Lawrence County on the Ohio River on the south. During 1936 a small pool of patchy character was developed in Butler township, Knox County. Seventeen wells were completed in the Clinton sand, of which 13 were gas wells and 4 were dry holes. The average initial production secured per well drilled, including dry holes, was 1,288,000 cu. ft. The average depth of the Clinton sand was 3000 feet. A gas well was completed in lot 9 of Franklin township, Tuscarawas County. Production was found in the first Clinton sand at a depth of 4354 ft. The initial open flow after shot was 828,000 cu. ft. and the rock

Jan 1, 1937

Francis Drake, Bulawayo, Rhodesia, So. Africa (communication to the Secretary *):—I should like to place on record some data in addition to those given by Mr. Canby in his paper. I regret that my notes have been destroyed so that I can give no accurate measurements of the water jacket that I am about to describe. This furnace mas erected in Cerro Gordo, Inyo county, Cal., early in 1875, and I think it quite possible that it was the first applied in lead smelting. It was made of plate iron and elliptic in shape, the inner dimensions being about 54 by 42 in. by 48 in. high. The distance between the inner and outer plates was about 6 in. Tuyere holes, one at the back and two on each side, about 12 in. in diameter, were made in this, and in these were placed cast-iron water tuyeres about 16 in. long, the diameter of the blast orifice at the point being about 3 in. The height from tuyeres to feed door was about 9 ft., but the top of the charge was kept about 5 ft. above the tuyeres. There was a space of about 12 in. between the jacket and the top brick-work. This brick-work was supported by a cast-iron plate resting on four cast-iron columns. At the beginning, the jacket was lined with air-dried radial bricks, made of crushed quartz and fire-clay, as it was thought that the jacket would not stand the heat on its bare plates. After a short time the practice was altered and no lining mas put in. The jacket was closed at the top and had a steam drum connected by two pipes at the back. This steam drum was connected to the boiler in which the steam was made for driving the Baker blower, the rock breaker and the pumps. The bottom of the jacket mas also connected to the boiler. The jacket was run under boiler pressure (80 Ib.) for some time, but eventually cracks developed in the inner plate between the tuyere holes,

Jan 1, 1913

By J. F. Myers, F. M. Lewis

The purpose of the mill tests reported herein, was to determine the relative power efficiency of fast and slow rod mill speeds on the ores of the Tennessee Copper Co. The tests were carried out at the Isabella Mill of the Tennessee Copper Co. under normal operating conditions. Every effort was made to keep the ore supply and other conditions constant, but it will be noted that some slight variation did occur. The open circuit 6 by 9 rod mill, and ore, used in these tests have been previously described.' Four motor drive pinions were available and the tests were performed in the following manner: each pinion was used to drive the mill for a period of one week. Constant sampling prevailed during the test run, and a composite sample for each speed test was made. Realizing that some slight liner wear took place during the four-week test-run, and that some slight variation of the ore may have taken place, a second and then a third series of four-week test-runs were made with the four different pinions. The screen analysis of each of the three-week run samples at the various speeds were composited and the results are shown in Table 2. The authors feel that the 22 weeks of operation consumed during these test-runs would represent fairly the effect of each mil1 speed. The data of line 37 show that within the error of sampling and plant operation, the tons of minus 65-mesh material generated per horsepower hour was the same at all four speeds. Obviously, rod and liner consumption could not be determined for each mill speed in so short a time. The rod load was maintained at a uniform level throughout the series of tests. The authors have operated rod mills at various speeds over the past several years, and it is their observation that rod consumption is directly proportional to the mill speed. Likewise, that the rod consumption per unit of work performed is a constant, providing that all other operating factors remain the same. It is a well known fact that the efficiency increases in a ball mill as the speed decreases. This is due to lateral segregation of the large and

Jan 1, 1950

By J. Ostachowicz, B. Holynska, M. Lankosz

The paper presents an analyzer and the method for the continuous determination of weight percentage of ore grains with diameter smaller than 75 µm in mineral slurries. The method is based upon the measurement of characteristic x-rays of copper excited by primary radiation of two different energies 16.5 keV and 60 keV from Pu238 and Am241 sources respectively. Additionally the backscattered primary radiation is measured in order to correct the variations of the solids content in the slurry. Since the particle size distribution of slurry can be described by the Rosin-Rammler formula, some calculations have been carried out in order to evaluate the influence of distribution parameters upon the results of the measurements of weight percentage U75 of particles smaller than 75 µm. The influence of solids content and of the copper concentration variation on the results has been also evaluated.1 It resulted from the calculations that the ratio rl/rz, where rl and r2 are the relative intensities of copper characteristic x-rays excited with 16.5 keV and 60 keV photons respectively does not depend on the copper content within the range 1 % to 4% of copper and is slightly dependent on the solids weight fraction and its chemical composition. The change of the dispersion parameter of the Rosin- Rammler distribution from 0.5 to 0.9 results in a change of value of U75 of approximately 3.0%. The results of calculations have been confirmed by the results of laboratory experiments. Therefore, a prototype of industrial analyzer for continuous determination of weight percentage of particles smaller than 75 µm has been designed and made. Its schematic drawing is shown in [Fig. 1]. Slurry is flowing down through steel flow-cell of the length equal to approx. 2 m. In the center, two XRF measuring heads (1) and (2) are located. Each of the heads comprises a rigid waterproof cover (3) with the mylar window (4), in which a proportional counter of resolution 15% for 6.4 keV is mounted with a preamplifier (5). The low- energy isotope source (6) is centrally located above the detector

Jan 1, 1980

By F. J. Tuck

The Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3? in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1½-in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1939

THE relation of labor to the accident rate in mines is admirably epitomized by Thomas T. Read in his paper presented at the St. Louis meeting, in the sentence "Reliance for accident prevention must be upon the individual worker himself." In connection with the inspection of mines for the fixing of merit premium rates for insurance under workmen's compensation, it has been the practice of The Associated Companies to allow 60 per cent.of the credits for safeguarding of the physical hazards of the mine and 40 per cent. for the human element. By "human element" is meant. that inherent tendency of the industrial worker to be careless, negligent or disobedient, in respect to his own safety, and after that also f his fellow workman. This is a tendency not only of the laborer or of the skilled miner, but of all human beings, working or traveling, anywhere. This element of mine safety, sometimes called the moral hazard, has been admirably shown by statistics compiled from the records of the Department of Mines of the Union of South Africa to be clue in about equal measure to the carelessness of the miner and to that of the operator. These statistics show that about one-half the fatalities in mines are clue to the so-called hazard of the industry, or what is sometimes called the dangers inherent to work or misadventure. Of 2497 fatalities investigated, including over 200,000 employees, for a period of over 2 ½ years, it was found that 17.5 per cent. were due to faulty plant or material, fault of the foreman, or of the management-in short were-clue to the operator; 17.1 per cent. to disobedience of orders, carelessness or ignorance of injured persons; and 5.9 per cent. through fault of others, including fellow workmen. The fault of the operator is evidenced by failure to give proper warning, failure to inspect, failure to furnish proper equipment, and neglecting to comply with the recommendations of the inspector. That education and training of the mine operator as well as of the mine worker

Jan 2, 1918

By F. J. Tuck

The Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3? in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1½-in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1939

By Gilbert Cady

EXTENSIVE Sampling of coal in Illinois during the past 10 or 12 years by the State Geological Survey, in cooperation with various organizations, such as the U. S. Bureau of Mines, the University of Illinois, and the Illinois Cooperative Mining Investigations, has made possible the delineation of two areas of low-sulfur coal in the southern part of Illinois. The sulfur content is less than 1.25 per cent., so that, if otherwise suitable, these coals can be employed for metallurgical uses and for the manufacture of water-gas and retort gas. One of these areas is small and lies in Jack-son County, near Murphysboro, the other is much larger and includes a large part of the famous Franklin County field. A small area of No. 2, or Murphysboro, coal has been worked for many years near the town of Murphysboro, Jackson County, Ill. In two mines, at least, the coal has a sulfur content of less than 1.25 per cent. It is doubtful, however, whether this field will ever be a source of large tonnage as the total area underlain by low-sulfur coal in workable thickness is probably less than 15 sq. mi. (24.14 sq. km.), and a large part of it has already been worked out. The location of the area of low-sulfur coal in the Franklin County field is shown in the accompanying map. The small area underlain by the Murphysboro low-sulfur coal is shown near the town of that name in the central part of Jackson County. The larger area lies in the west side of Franklin County, extending also about 6 mi. (9.65 km.) south into Williamson County, about 4 mi. (6.43 km.) west into northern Jackson and western Perry County, and northward an undetermined distance into Jefferson County. All but the northern limit of the area is fairly well defined by sampling in numerous mines. The inner cross-lined area is underlain by coal having less than 1 per cent. sulfur, the outer boundary surrounding the area Underlain by coal having less than 1.25 per cent, sulfur.

Jan 7, 1919

By J. C. Platt

1 desire to call the attention of the Institute to what is believed to be a new improvement in 'the construction of journal-bearings, having for its object the reduction of original cost as well as cost of renewals. In an ordinary railroad car we find the space between the top of the axle and the top of the box is filled with a "brass," weighing from seven to ten pounds. Of this amount of metal a comparatively small portion is subjected to the wear which it is intended to meet. The balance is, practically, a filling material, which from habit has long been constructed of the same metal. The Defreest bearing is made of three parts, namely, a malleableiron back, a bronze bearing-piece, and between them a filling-piece of sheet lead. The bronze takes the wear of the axle, the iron fills up the space and acts as a backing to the bronze, and the lead, being soft, adapts itself to the inequalities in the surfaces of the iron and bronze castings, thus insuring a uniform bearing on all points, and making it unnecessary to bore out the iron or turn off the bronze to bring them to a perfect contact at all points. These three park are joined together by two soft brass rivets, with counter-sunk heads, to prevent separation in handling. A groove is cast in the iron, and a corresponding rib on the bronze, to prevent the latter from turning with the axle when in place. In renewals it is ordinarily necessary simply to drive out the rivets and renew the bronze and lead. The iron part is not subjected to much wear and should last for years. It is evident that the first cost of these journals, and also the cost of renewals, must be much less than the old form. This difference amounts, at the present price of materials, to $9.60 for an eightwheel car, in first cost, and $4.72 for renewals. These bearings have been in use, and found to do what is claimed for them.

Jan 1, 1880

By Frank Hultgren

The influence of grain boundaries and polygonized subsructure on the flow stress of commercially pure aluminum has hem studied. A systematic inz-estigoti017 of grain size and subgrain size and mis-orientation was pursued; the contributions of pain boundary md substruture hardening were found to he additive fuiictions. Subgrain boundaries exert greater influence on hardening at room temperature than do grain boundnries. Both subgrain diameter and misorientation influence flow stress, but only to the extent that both contribute to the dislocation density. The flow stress due to substructure may he described by the equation of = abp1/2. THE origin of substructure hardening in metals has remained unclear for a long time. Lately, both theory and experimental techniques have become more exact and merit a closer examination of the subject. In the present work, the influence of polygonized substructure size and misorientation in commercially pure aluminum on mechanical properties has been systematically investigated. The influence of substructure on mechanical properties has been compared with that of grain boundaries. In addition, the works of several authors are compared with theoretical predictions of substructure hardening. EXPERIMENTAL TECHNIQUES Aluminum of 99.9 pet purity (0.04 Fe, 0.046 Si, 0.00 Cu) was employed. Various grain sizes were produced by heavy (over 90 pet reduction in area) cold drawing and recrystallization at various temperatures. A (111) fiber texture was observed in all specimens. Grain sizes were analyzed statistically. Substructure of varying size and misorientation was produced by prestraining specimens of various recrystallized grain sizes. Specimens for mechanical testing and substructure analysis were recrystallized, prestrained, and annealed together. The samples were prestrained from 5 to 25 pet in tension at room temperature and annealed at 200" to 370°C for 2 hr. All samples were rapidly cooled (in air) from the anneal to retain the subgrain wall structure developed at the annealing temperature. A clearly polygonized substructure was developed in all cases. Substructure size was measured by the Berg-~arrett' technique and analyzed statistically. Substructure misorientation was measured in the following manner. Individual grains in the polycrys-talline aggregate were isolated and their intensity distributions mapped using an X-ray goniometer and Geiger counter. From the observed profiles, the

Jan 1, 1964

By AIME AIME

LEADING off the Thursday morning session on Non-metallics was C. E. Heinrichs' paper, "Phosphate Flotation, Its Place in the Technology and Economics of the Phosphate Industry." Mr. Heinrichs also presented a closely related paper, "Milling Methods and Costs at the No. 2 Concentrator of the Phosphate Recovery Corporation," by H. S. Martin. The first of the papers points out the great significance of flotation to the phosphate industry, inasmuch as flotation practically doubles the potential recovery, thereby decreasing production costs and increasing reserves materially. The second paper describes three such plants, two of which are in Florida, the third being at Wales, Tenn. Operating characteristics and costs are reviewed. Answering inquiries from the floor, Mr. Heinrichs said that the adoption of a new parallel-shell dryer, from 60 to 80 ft. long, instead of the old single-shell countercurrent dryer, had increased the unit drying capacity over 300 per cent and had reduced the drying cost to less than 25c. per long ton of dried product. The initial moisture is from 15 to 18 per cent and the final about 2 per cent.

Jan 1, 1933