Search Documents

By W. L. Chen

The Batac jig was first introduced in the US for fine coal cleaning in 1973 (Tackett, 1977; Hake, 1976). Since then, a total of six such jigs of various sizes have been installed in five US plants for a total capacity of 2346 t/h. The raw coal size ranges from 19 mm x 0 to 9.5 mm x 0-fraction sizes previously fed to heavy medium cyclones, Deister tables, or water only cyclones. Growing interest in the Batac jig as a replacement for the above equipment is due to the following reasons: • Unlike heavy medium cyclones, no magnetite is required. As a result, the operating cost of the plant is reduced. • The compactness of equipment is unique on a unit ton per hour basis as compared to other equipment. • Solid state electronic control of jig stroke length, frequency, and jig bed depth makes the equipment highly efficient. Installations of Batac jigs in the US as of June 1980 are shown in [Table 1]. Use of the Batac jig is even greater outside the US (Anonymous, 1980; Chen, 1980). Its use is not limited to fine coal but is applied to coarse coal as well, with 102 mm size in the feed (Zimmerman, 1975). In countries where consumption of magnetite associated with the heavy medium system of coal cleaning is considered a waste of iron ore resource, the Batac jig is regarded as the primary choice in the selection of cleaning equipment (Chen, 1980).

Jan 1, 1981

By Keith C. Hendrick

The mining industry of Canada, stretching from coast to coast and reaching into the most remote regions of the country, is of fundamental importance to the national economy and the well being of many communities outside the main urban areas. The production, processing and transportation of a host of mineral products provide employment for about 9% of the country's labour force; and their shipment to export markets provides an important contribution to the balance of payments. In 1976 Canada's metal and mineral production had a value of $5.24 billion, of which zinc and lead accounted for $862 and $129 million respectively, or 19% of the total. By all standards the Canadian zinc and lead industry is large and, therefore, important to the country as a producer and the world as a supplier. This report will review the development, describe the present status and discus current problems and future potential of the industry. The discovery and successful development of the major lead-zinc deposits at Kimberley, British Columbia, provided Canada with a solid base from which to grow. The breakthrough in metallurgical technology using differential flotation to separate the lead and zinc sulphides and the refining of high purity metal by electrolytic methods not only helped Canada to compete with other world producers but also provided a new source of these metals at prices and qualities that encouraged the development of new end uses.

Jan 1, 1977

By R. A. Meussner, R. T. DeHoff, F. N. Rhines

ZINC diffuses through copper more rapidly than does tin. Accordingly, when a ternary diffusion couple is made, by bringing an 0 copper-zinc brass into contact with an a copper-tin bronze at fixed high temperature, it is to be expected that zinc will diffuse into the bronze faster than tin diffuses into the brass. Adjacent to the brass side of the couple the total alloy content (zinc plus tin) should diminish, therefore, while next to the bronze side the alloy content should increase. Since the path of compo- sition change must be continuous, in a single-phased alloy, it should follow a curved and, in general, an S-shaped course. The realization of this prediction is demonstrated in Fig. 1, where the composition paths of two ternary diffusion couples are plotted on the appropriate isotherm of the copper-tin-zinc phase diagram. The diffusion couples were both made from a binary copper-tin alloy analyzing 5.0 pct tin placed against binary copper-zinc alloys analyzing 18.9 and 29.3 pct Zn, respectively. These alloys were produced from electrolytic grades of copper and zinc and a pure grade of straits tin, melted under borax in clay-graphite crucibles and cast in a vertical iron mold. Cylindrical pieces 1 in. in diam and 1 % in. long were machined from the casting and were faced by metallographic polishing to good matching end surfaces. Pairs of the cylindrical pieces were held

Jan 1, 1959

By H. W. Seamon

THE data here given were obtained by 1500 tests made, by the United Verde Copper Co. to determine the most economical air pressure for the operation of hammer drills under the varying conditions of use, and to investigate the variation in drilling speed at different air pressures Twelve models of drills were used at gage pressures ranging from 40 to 130 lb. No effort was made to harmonize theory and practice; but rather to formulate empiric rules that would cover the. average variation of the results obtained. These rules on the performance of hammer drills, based on the air pressure as the main variable, however, are not necessarily of universal application, but they apparently satisfy the results obtained in this series of tests. The drilling conditions at this property vary widely; an average of twenty-one machine shifts to a 3-ft. (0.9-m.) round has been found necessary in some of the development work, while an, advance of 56. ft. has been made in seven shifts in the "oxide" ground. This range pre-eludes the adoption of one type of drill as a standard; consequently almost every kind of hammer drill sold in this country has been tested. At present, sixteen models are in use, of which two types of the heavy (150 to 160 lb.) mounted drills, one of the light mounted drill, one stoper, and two hand plugging drills are considered as standard.

Jan 1, 1921

By Fred Van Covern

Before getting into a discussion of the subject of my paper, I want first to make it clear to everyone that I am speaking as an individual; and that any expressions of opinion that are contained herein, or may be expressed in any oral discussion that may follow its presentation, are entirely my own, and must not be construed to be the official opinion of the American Petroleum Institute. Demand fob Motor Fuel, 1936 During the year just closed the domestic demand for gasoline exceeded 481 million barrels. This compares with 434,810,000 bbl. consumed during 1935 and indicates an increase of 10.46 per cent. Export shipments amounted to 27,831,000 bbl. while in 1935 they totaled 30,613,000 bbl. Total demand, therefore, was 509,422,000 bbl., or 9.16 per cent above the 465,423,000 bbl. of 1935. Following are the figures for several years: Already we are supplying gasoline domestically and as foreign shipments at a rate almost 25 per cent greater than our low level of 1933. Before giving figures for 1937, I should like to spend a moment or two in discussion of gasoline inventories, from the point of view of minimum working stocks and other requirements and of probable actual levels. Inventories of Gasoline The year 1936 closed with about 62,900,000 bbl. of finished and unfinished gasoline in storage—about 6 million barrels more than was on hand

Jan 1, 1937

By Ben B. Cox

During the past year considerable progress was made in the exploitation of Iraq's resources, although no new fields were discovered. The principal development was the completion of the much heralded pipe line from Kirkuk to the Mediterranean, by the Iraq Petroleum Co., Ltd., and the beginning of crude exports to Europe on the second of August. Official ceremonies for the opening of the lines took place in January, 1935. The line in itself is sufficient achievement under the existing natural handicaps to deserve a moment's attention. It is 1151 miles long, composed of two independent lines made up mostly of 12-in. with some 10-in. and 8-in. pipe, and extends from Kirkuk westward 156 miles to beyond the Euphrates River as a double line. From that point, near the village of Haditha inside the Iraq border, it bifurcates, one leg going as a single line to Haifa through the British Mandated Territories of Trans-Jordania and Palestine, and the other to Tripoli through the French Mandates of Syria and the Leban(on)ese Republics. The total length of the Tripoli line is 532 miles, of the Haifa line 619 miles. The line leaves Kirkuk at an elevation of 1013 ft., drops to 350 ft. at the Tigris, to 200 ft. at Wadi Tharthar west of the Tigris and again to 300 ft. at the Euphrates, rises to more than 3150 ft. at mile 451 on the central Arabian steppe along the south line and to more than 2500 ft. at mile 466 along the north line. On crossing the rift valley of the Jordan River south of Galilee, it drops abruptly below 850 ft. below sea level, requiring the use of extra heavy 8-in. pipe and a relief station to reduce the pressure. A picked group of American welders, under H. S. Austin, of the Ajax Pipe Line Co., laid the line. It is coated, wrapped, and buried 30 in. beneath the surface in solid rock along much of the route. It crosses four large rivers and wide stretches of alkaline soils. Twelve pumping stations are employed, three of which are double east of the bifurcation. Each single station houses three 500-hp. crude-burning deisel engines flexible-coupled to reciproratirig pumps. Each pumping unit is capable of handling a minimum of 21,000 bbl. of oil, giving the entire system a

Jan 1, 1935

By AIME AIME

A SIDE from the technical sessions held as noted elsewhere, the chairman of the various sub-committees of the Mining Methods Committee, together with a few other specialists, were invited to a conference with President Bradley, which was held on Wednesday afternoon, Feb. 20. The general plan of a comprehensive series of comparable papers descriptive of mining practice in various parts of the country, launched by this committee some seven years ago having been adopted by the U. S. Bureau of Mines, the feeling was general that the Committee could safely 1eave.that part of its work in these capable hands and turn its attention to other matters. The plans of the Bureau were presented as below by Charles William Wright of the Bureau.

Jan 1, 1929

By R. F. Miller

DUE to wartime secrecy restrictions a large part of the technical information developed by government and industrial laboratories was withheld from distribution. Much of this information has now been released or "declassified" and reports of technical work carried out during the war in allied and enemy countries are also becoming available. Information on the latter subject has been augmented by the work of the Technical Industrial Intelligence Corps of the U. S. Army. Through the Joint Chiefs of Staff, rep¬resentatives of this Corps co-operated with the British Combined Intelligence Observations Subcommittee, and some of the observations were made by combined personnel of both groups. The U. S. Government has undertaken the indexing and abstracting of all of this information in the Bibliography of Scientific and Industrial Reports, a weekly bulletin which appeared first early in 1946. Other publications, such as the Bulletin of the British Iron and Steel Institute and The Metals Review of the American Society for Metals, provide abstracts of domestic and foreign magazine articles and papers presented to technical societies. However, they do not cover the industrial and government reports recently released by the Government nor the reports of the Army investigators hence the new bibliography is a welcome addition to our metallurgical library.

Jan 1, 1947

WALTER N. CRAFTS,* Toronto, Canada (written discussion?).-During the forging of 9.2-in. shells -for the United States Army, it was noticed that better results were obtained in certain instances when test bars had been held sometime before pulling. An investigation, therefore, was made by our metallographer, Mr. F. M. Arnold, to determine the effect of seasoning. The forging consists of a single operation, piercing a solid cast blank. The test sections were cut from the walls by an oxyacetylene flame, one piece from the nose end and one from the base on the opposite side. The test pieces were not heat treated in any way and the tests and seasonings were carried on at normal atmospheric temperatures. The specifica-tions were as follows: Standard 2-in. test bar, 0.505 in. in diameter; elastic limit, over 19 long tons, or 42,500 lb.; ultimate stress, 39.6 to 49.1 long tons, or 87,500 to 110,000 lb. per sq. in.; elongation, over 13 per cent. As a preliminary test two heats were selected; BP555, which was tested and reported failed on elongation on Aug. 20; and B01771, which was tested and reported failed on Aug. 24. On Aug. 29, retests were cut and machined from the same shells and held till Sept. 3 (5 days) when they were pulled. Both sets of results are given below.

Jan 12, 1919

By F. F. Sharpless

ON Saturday evening, Sept. 9, a small party of Institute members, their wives and friends, left New York to attend the Fall Meeting of the Institute at San Francisco. In this party there were: President and Mrs. Arthur S. Dwight; Mr. and Mrs. George D. Barron; Mr. and Mrs. H. J. Stehli; N. S. Spencer and Miss Spencer; the Secretary and Mrs. F. F. Sharpless. They were joined at Chicago by E. F. Eurich, and by Mr. and Mrs. R. L. Baldwin and daughter. Our party was met at Chicago by Mr. and Mrs. L. V. Rice, Mr. and Mrs. A. D. Terrell and W. F. Boericke, who constituted themselves an impromptu entertainment committee and proceeded to carry out a delightful little program. We were taken to the Lake Shore drive, where a stiff wind off the lake refreshed us after a sultry day on the train, and on our return to the city saw Chicago illuminated with all its brilliance of electricity. We were entertained at dinner at the Drake Hotel. In spite of being two hours late getting into Omaha, we were right on the dot at Denver on Tuesday morn-ing. Horace F. Lunt came to the hotel soon after breakfast, and told us that a trip to the mountains had been planned. Having learned the number in the party, he began to gather up his automobiles for a 10 o'clock start.

Jan 10, 1922

By George W. Maynard

In the Journal of the Iron and Steel Institute for the year 1878, in the account of the proceedings of the annual meeting in March of that year, when Mr. Bell read his paper On the Separation of Phosphorus from Pig-Iron, occurs the following statement, as part of the reported discussion of that paper: " Mr. Sidney Thomas stated that he had succeeded in effecting the almost complete removal of phosphorus in the Bessemer process. Experiments had been carried on at Blaenavon, with the co-operation of Mr. Martin, on quantities varying between 6 lbs. and 10 cwt., and some hundred analyses made by Mr. Gilchrist (who had the conduct of the experiments from the first) showing the removal of from 20 per cent. to 99.9 per cent. of phosphorus in the converter. He believed the practical difficulties in the way had been overcome, and that Cleveland pig might be made into good steel without any intermediate process. He hoped on a future occasion to lay full details before the Institute." I was present at that meeting, and I doubt if any one in the hall knew, either by sight or name, the young man who had dared to rise in that august body and claim that he had accomplished that after which the great metallurgists of Europe had been unsuccessfully striving ever since Mr. Bessemer's great discovery. I remember distinctly the pitying smile of derision and the stony stare

Jan 1, 1885

By Thomas Clagett

THE Pocahontas coal field comprises the area in Tazewell County, Va., and Mercer and McDowell Counties, W. Va., in which Nos. 3 and 4 Pocahontas seams of bituminous coal are mined. It is a mountainous region with ridges rising 300 to 1000 ft. (91 to 305m.) above the very narrow valleys and, except for some poorly kept farms along the tops of the ridges and the area occupied by the mining and coking plants and villages, is wooded throughout. First shipments were made from Pocahontas in 1883. There are now, about 100 mines, 95 per cent. of which are drift mines. At the end of 1920, approximately 298,000,000 gross tons of coal had been produced and 35,000 acres of coal mined. No. 3 seam is from 4 to 10 ft. (1.2 to 3 m.) thick, but the change is gradual and the thickness fairly uniform in any particular locality. It has a streak of bone, about 2 in. (5 cm.) thick, io which the coal adheres on both sides. In parts of the field this bone is replaced by hard slate, usually from 2 to 4 in. thick. The seam has a slate or fireclay bottom and a draw-slate top. No. 4 seam is from 65 to 80 ft. (19.8 to 24 m.) above No. 3 seam, and of minable section only in the western part of the field. It is from 3 to 8 ft. thick and has two streaks off bone, each from 1 to 2 in. thick. It has a fireclay or slate bottom and is overlaid by from 4 to 24 in. of a laminated coal and slate, locally termed "black rash," which is separated from the coal seam by about 3 in. of slate. This "black rash" averages about 25 per cent. ash, but contains some clean coal. The coal in both seams is quite soft. Cleavage sufficiently well defined to exert an influence on the mining is rare. Overlying strata are slates, shales, and sandstones, the sandstones predominating, extending from .30 to 1000 ft. above No. 3 seam. The strata directly above the. draw slate of No. 3 seam, or "black rash" of No., 4 seam, and up to the first sandstone are usually slates or shales, about 10 ft. thick over the

Jan 5, 1922

By P. W. Davies, B. Wilshire

PREVIOUS investigations on the effect of stress changes on the high-temperature creep and fracture behavior of metals have been confined mainly to the testing of complex alloys.172 Most of these alloys are structurally unstable during creep because of such effects as recrystallization, overaging, and so forth, so that the results are of limited application. The only pure metals on which observations have been made appear to be lead3,4 and aluminum5 tested under conditions which allow rapid recovery to take place. The present work describes the effect of a single stress change on the creep and fracture properties of a metal in which recovery is very slow. A Ni 0.1 at. pct Pd alloy was used so that grain growth and recrystallization did not occur during creep testing. Specimens of this material were heat-treated to give a uniform grain size of 10 grains per mm. Creep tests were carried out at 500°C using Denison T.47 machines; details of the creep-testing procedure have been given elsewhere.' All specimens were tested at a constant initial stress of 5 tpsi which gives, in an uninterrupted test, a minimum creep rate of ~10-3 pct per rnin and a life of -7000 min. Specimens were loaded under these standard conditions and after 1500 min, when secondary creep was well-established, the stress was changed to either 8, 7, 6, 4, 2, or 0 tpsi for a period of 180 min. After this time the original load was reapplied and the tests continued to fracture. The results are shown in Fig. 1. No detectable creep occurred during the period of reduced load, even at 4 tpsi, and on reverting to 5 tpsi the creep rate returned to its original value immediately. Increasing the stress to 8, 7, or 6 tpsi resulted in an instantaneous extension followed by a period of transient creep leading to a new steady creep rate. On returning from these higher stresses, the resulting creep rate at 5 tpsi was very low compared with the original value. Furthermore, the higher the stress during the stress change, the lower was the final creep rate. It is significant that the rupture life is comparatively unaffected by any of these stress changes.

Jan 1, 1965

By C. Richard Tinsley

SUMMARY A detailed analysis of nickel, copper, and cobalt recovery from manganese nodules shows simple rates of return of 9-15% in 1985. A sulfur dioxide roast process yields a slightly better return than an ammonia leach technique. Nodule tonnage predictions tend to be over-optimistic and more conservative forecasts show that market penetrations are only significant for cobalt and manganese. However, cobalt prices are unlikely to fall to the level of nickel. Between now and 1985, cobalt is expected to be in balanced to tight availability. INTRODUCTION Deep-ocean manganese nodules are one- to two-inch concretions which cover 2040% of large areas of the ocean bottom. Commercial targets far these black, potato-like nodules are located in the North Pacific at water depths of 5,000-6,000 m. in a belt roughly midway between Hawaii and Mexico. However, good grade nodules are not solely limited to this belt as areas southwest and northwest of Hawaii, as well as in the Indian Ocean, contain concentrations of acceptable grade manganese nodules. Some 90% of the nodules are found half-buried on the deep ocean bottom. A siliceous-ooze host soil combined with low sedimentation rates, certain ocean currents, and possible geo- thermal effects are favorable factors far nodule formation. The viewpoints and analyses in this paper are the author's own and should not be attributed in any way to Amoco Minerals Co.

Jan 1, 1976

By Ray Schmidt

When your committee approached me for a talk on "Mechanics of Secondary Metals Collection," I replied that this subject would probably not be very interesting to a group of engineers and requested permission to dwell on the Westinghouse Salvage Setup. I will attempt to avoid duplicating the points covered by Mr. Bliven. The Westinghouse Electric and Manufacturing Co. has main manufacturing Divisions in 25 cities and 9 different states, scattered throughout the country, as well as Naval Ordnance Plants in two midwest cities, and a Merchant Marine Turbine Plant, and two special War Production Plants in Eastern cities. You can, therefore, see that we must have a well rounded pro- gram with the entire respect and sponsorship of the various Division Managements. That was not so easy to get. Management has been a great deal like the general public in the past. I am sure most of you can remember the not very ancient day when each town had a ragman who had a horse and wagon and went through the streets of the town, from door to door, picking up what scrap he could accumulate. He was known as a junk man, and indeed, with the exception of the very last few years, the attitude of manufacturing management was: "We have a job to do. We have a product to manufacture. We don't have time to bother with the junk business."

Jan 1, 1943

By Wendell E. Dunn

INTRODUCTION The early history of the chloride process has been recorded in a chapter of a Bureau of Mines bulletin (9 by one of the inventors of a chloride process, Stewart Croasdale, who is famous for the Pohle- Croasdale Process. The earliest use of chlorine in metallurgy was in 1557 by Bartholome Medina. But apparently even earlier there was knowledge that salt could be used in gold and silver extraction because a treatise, de la Pyrotechnica, published in 1540 in Venice, asserted that silver could be obtained from its ores by a wet salt process. In 1609 a priest, Alonzo Barba, invented a process using a copper vessel and boiling a solution of salt to extract silver chloride ores. The copper vessel was, of course, one of the reactants. This led to the Kronke process introduced in Chile in 1860 which substituted cuprous chloride for the kettle. A major step was taken in Europe in the late 1700's to chloridize roasted silver ores in combination with amalgamation using iron to reduce the silver chloride. By 1843 the Augustan process was introduced. Ores were roasted with salt and leached with a saturated salt solution. The silver chlorides passed into solution from which silver was precipitated by copper. In 1848 sodium or calcium thiosulfate solution of silver chloride was suggested by Dr. John Percy, and the idea was applied in 1856 by Von Patera in Bohemia.

Jan 1, 1983

By FREDERICK W. BRADLEY

MINING is one of the world's oldest industries and has pioneered the civilization of all new lands. Today, mining is not only one of the essential and basic industries of the world, but it is constantly growing in magnitude and becoming more important. We think that the most of our mining is done in the western portion of this country, but in the old State of Pennsylvania mines and products derived from minerals account for about two-thirds of the entire productive wealth of the State. As our forests are denuded, mining furnishes substitutes for timber in the way of concrete, gypsum board, etc. ; and as civilization increases the wants of mankind, mining is producing metals and minerals of every kind in increasing quantities. For example: during the past ten years the per capita consumption of copper in the United States has increased 49 per cent, to 14.56 Ib.; that of lead has increased 35 per cent, to 12.24 lb.; and that of zinc has increased 70 per cent, to 9.57 Ib. The consumption in European countries is about one-half of this, and there are other countries with large populations where there is virtually no consumption; so when all other countries catch up in consumption with our country, you can see what an enormous demand there is going to be for the metals, even to the extent of having to find substitutes for copper, lead, and zinc.

Jan 1, 1929

By W. L. Zeigler

THE tailing from the gravity concentration plant of the Hecla Mining Co., Gem, Idaho, was former-ly loaded into railroad cars to be used for ballast, highway surfacing material, or concrete work, or dis-posed of by an aerial tramway, which dumped it into another gulch. The tailing averages about 1.2 per cent lead and 0.8 oz. silver to the ton. Further treatment for the recovery of the valuable metals had been investigat-ed several times with results that did not warrant the construction of a retreatment plant; but early in 1925 experimental work was again started with small tests, and later with a 10 tons per day flotation test plant. This showed that the tailing could be ground and treat-ed by flotation at a profit. It was decided to make the new flotation plant an addition to, rather than incor-porate it in the old concentrator, the original capacity of which had been increased many times, the present arrangement being by no means ideal. The old mill buildings were of timber and board contruction, creat-ing more or less fire hazard, so all new construction was made fireproof. Construction work on the new plant was started in the middle of July, 1925, and the plant was placed in operation early in December. The building is of concrete and steel with hollow tile walls, steel sash and corrugated asbestos roofing. The ball-mill floor has for its foundation a cellular reinforced concrete block about 14 ft. deep, extending to cemented river gravel, and the cells filled with tailing to give weight to the block. Overhead, built into the steel frame, is a 5-ton hand-operated traveling crane. With both ball-mills running fully loaded, there is not the slightest trace of vibra-tion in the foundation or building. The flotation floor is of reinforced concrete beam construction and spans Canyon Creek. Adjustable plunger feeders are arranged under the the tailing-bin, which feed by gravity to a 14-in. eleva-tor, discharging to a short 18-in. conveyor. From the conveyor the tailing is discharged into a dividing hop-per, from which point the plant is arranged in three separate units. Each unit consists of a ball-mill in closed circuit with a classifier, and an 8-cell flotation machine and has an approximate capacity of 300 tons per 24 hours.

Jan 8, 1927

The State Mining Experiment Station, Missouri School of Mines and Metallurgy, Rolla, Mo Charles H. Fulton, Director of the School of Mines Martin H. Thornberry, Director of the Mining Experiment Station. From the State Mining Experiment Station are issued all the general and technical bulletins of the School of Mines The latest bulletin containing a complete list of publications will be sent upon application to the Director of the Station Residents of the state may obtain bulletins as issued without charge, or may ask to be placed on the mailing list. Nonresidents should write to the Director for further information concerning specific bulletins. From the long list of bulletins the following have been care¬fully selected as being most likely to interest the geologist and the mining engineer. Vol 8, No. 1 (1916), Bibliography of concentrating ores by flotation, by J Cunningham, vol 1, No 3 (1912), Some apparatus and methods for demonstrating rock drilling and the loading of drill holes in tunneling, by L E Young, vol 2, No 1 (1915), Comparative tests of piston drill bits, by C R Forbes and L M Cummings; vol 2, No 3 (1916), Cupellation losses in assaying, by H. T Mann and C. Y Clayton; vol 4, No 1 (1917), The hydrometallurgy and electrolytic precipitation of zinc, by F D. James; vol 4, No 2 (1917), The effect of additional agents in flotation, pt 1, by M. H. Thornberry and H T. Mann, vol 5, No 1 (1919), The carbonization of Missouri cannel coals, by H L. Dunlap, K. K. Kershner and V. X Smiley. Vol 5, No. 4 (1921), Coal mining methods in Missouri, by W W Weigel, vol 6, No 1 (1921), The problem of the St Peter sand¬stone, by C L Dake, 50 cents, vol 6, No. 2 (1922), Bibliography on the electrothermic metallurgy of zinc, by B M. O'Harra, vol 6, No. 4 (1923), Experiments on the distillation of zinc from complex zinc-lead-silver ores, by B M. O'Harra and E S. Wheeler, vol 7, No 3 (1924), Underground loading devices, by C. E. van Barneveld, 81; vol 7, No. 4 (1924), Briquetting of zinc ores, by B. M. O'Harra; vol. 8, No 2 (1925), A treatise of Missouri clays, by M. H. Thornberry.

Jan 1, 1933

By W. F. Stowasser

Robert E. Hagen (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Stowasser and his associates are to be congratulated on their achievements in developing the design of a pilot agglomerating plant, based on information obtained from experiments made in a laboratory sinter pot, and subsequently constructing and successfully operating this plant. In his Transactions article, May 1955 (vol. 201) Mr. Stowasser stated that the output of his heat treating strand was about 2 Lt per sq ft of grate area per day and that the fuel consumption was 0.7 to 0.8 million Btu per Lt of product. If it is assumed that the burning zone extends from the back of the ignition furnace to the beginning of the recuperation windbox, only about 1/3 of the grate area over the windboxes is utilized for burning pellets, and the actual rate at which partially dried pellets are burned is about 6 Lt per sq ft of grate area per day. It may be interesting to compare the above operating data with that obtained at the Extaca plant, where taconite concentrate is treated on a conventional sin- tering machine using limestone or hydrated lime additives with no recuperation of heat. The entire windbox area is used for burning, and a production rate of 2.5 Lt per sq ft of windbox area per day has been attained at a fuel consumption of 1.8 to 2.0 million Btu per Lt of product, the latter being considerably in excess of that reported by Mr. Stowasser, partly because a circulating load of returns amounting to 28 to 30 pct of the machine feed is used and because no attempt is made to recuperate heat from the waste gases. With the high capital and labor costs prevailing today, it seems that future development of the downdraft grate pelletizing process should be directed toward taking advantage of the high burning rate of predried pellets and increasing capacity, perhaps at the expense of fuel economy, by decreasing the proportion of grate area utilized by ancillary functions. For example, eliminating the cooling zone and using this area for burning would increase the proportion of grate area available for burning from 33 to 50 pct of the total windbox area, and a proportionate increase in capacity would result.

Jan 1, 1956