Search Documents

By R. Lee-Aston

HALLOWAY mine of Tennessee Copper Co. at Copperhill, Tenn., has been under development for several years. It has two shafts, the A shaft, 1336 ft deep from the surface to the 16 level, and the B shaft, lying 500 ft to the southeast and extending 1385 ft deep from the 10 level down to the 24 level. A section through the two shafts, Fig. 1, shows the development work entailed by the proposal and the area involved. The Problem: For operational reasons it was necessary to extend the B shaft from the 10 level to surface, and the pilot hole and raising method was chosen. This method had been used to extend the Company's Boyd manshaft from the 10 to the 14 level in 1954, but no satisfactory hole surveying method had been employed. In that instance, when the hole was located it was found to be about 8 ft from its calculated position. The success of this shaft extension method lies in the ability to keep the pilot hole within the proposed shaft diameter for nearly the entire length. The approximate 670 ft of extension distance in one hole was thought to be excessive because of deflection encountered locally in other core drilling. Since a connection between the two shafts, intermediate between the surface and the 10 level, would be required at some future date, the pilot hole drilling was done in two sections. This intermediate level was fixed at the 6 level and distances became 470 ft from surface to the 6 level and 230 ft from the 6 to the 10 level. A rock pentice of 25 ft was left temporarily in place just above the 10 level.

Jan 3, 1958

By C. H. Curtis

THE valuable mineral content of the current feed to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalcocite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil, as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0).

Jan 1, 1950

By AIME AIME

ON Thursday, Oct. 9, oil men from far and wide gathered at Beaumont, Texas to participate in a three-day celebration of the fortieth anniversary of the completion of the famous Lucas gusher well at Spindletop field just south of Beaumont, and to pay tribute to Anthony F. Lucas, for whom the Lucas Medal of the A.I.M.E. is named. In the afternoon the gathered host drove to the site of the discovery well to dedicate a 58-ft. granite monu¬ment erected on the spot where the original derrick stood. Representatives of the A.I.M.E. took a prominent part in the dedication ceremonies, giving the two principal addresses of the afternoon's program. Everette DeGolyer, past President, paid a personal tribute to Capt. Lucas, as a pioneer producer, an engineer, and a friend and well wisher of all young engineers. He gave a splendid picture of the useful and full life of Capt. Lucas who always took a great interest in the activities of the Petroleum Division of the Institute, from its inception to the time of his death.

Jan 1, 1941

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS, Secretary, 55 Wall St., Now York, N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. W. E. C. EUSTIS. Chairman. R. L. AGASSIZ, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annualmeeting in September or October. STANLY A. EASTON,- Chairman FREDERIC KEFFER,-Vice-Chairman: LYNDON K. ARMSTRONG, Secretary-Treasurer, P.O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 10, 1916

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hydroscillator. This increased grinding efficiency 28 pct over conventional units.

Jan 1, 1950

By A. H. Cottrel

SINCE metallurgy exists to provide strong, tough, engineering materials it must inevitably be perpetually concerned with the problem of brittle-ness. The steel-making industry was created because chemically unrefined iron is brittle. The steel-working and alloy-steel industries exist partly because hardness and ductility are mutually exclusive qualities in structurally unrefined steel. Yet, in spite of these immense industries, the brittle failure of steel ships hulls, bridges, pressure vessels, and pipelines, is still a contemporary problem. In fact, brittleness is a normal property of most solids, including metals and alloys, at low temperatures. Only face-centred cubic metals are commonly ductile at the lowest temperatures, and even here exceptions are known.'," Expensive are-melting processes. under inert gases or vacuum, have been developed to overcome brittleness in titanium, zirconium, columbium. and molybdenum. Polycrystal-line zinc, magnesium, and uranium have little ductility at room temperature. Beryllium, chromium, and tungsten have even less; similarly for antimony, bismuth, germanium, silicon, intermetallic compounds, and metallic carbides, nitrides, silicides, and borides. Oxides and other ceramics would be ideal creep-resistant materials but for their extreme brittleness when cold, and great efforts have been made to overcome this problem by mixing ceramics with metals. In fact, the traditional use of the name metallurgy for what is really the science of engineering materials is a recognition that most non-metallic solids have so far been precluded, by their extreme brittleness, from use as major structural materials in mechanical engineering. Most of what we know about brittleness in metals has come from studies of structural steel, and it is this material that shall mainly be considered. The things we have learned from it have a wider application, at least to other body-centred cubic transition metals, although the extent to which similar ideas can be applied to hexagonal metals and other materials is not yet clear. Fracture and Plastic Deformation The theoretical breaking strength of an ideal solid, about E/10 where E is Young's modulus, has been approached reasonably closely in experiments on fibres. But large specimens break at much lower stresses. For example, brittle cracks in large structural steel assemblies have been observed to spread catastrophically at speeds of 6000 ft per sec under stresses of about 10,000 psi, i.e. about E/3000. There are two sources of weakness; stress concentrations, and chemical agents in grain boundaries or on crack faces that lower the surface energy y of the material. Although we shall deal mainly only with the first of these, much of the discussion is also applicable to the second when different values of y are used. Griffith's well-known formula p = [ 2Ey/p(1 - v2)c]1/2 [1] gives the smallest tensile stress p able to propagate an atomically sharp surface crack of length c or interior crack of length 2c through a thick plate (compared with c) of elastically isotropic material of

Jan 1, 1959

By Potts N. L., Eilerts C. K., Summer E. F.

The second-order, nonlinear, partial- dillerential equation representing the transient radial flow of gas - condensate fluids in reservoirs has been integmted by using finite -dillerence equations and electronic computers. Effect was given to pressure -dependent permeability, viscosity, and compressibility and to distance-dependent permeability. The influence of a second-degree velocity term in the Darcy equation was investigated. Implicit methods were used and practical, convergent solutions were obtained with material balance to less than 6 x 10-4 for recovery of one- hall the reserve at constant flow rate. Integration results provide the productive period of a reservoir for a given constant rate and the fraction of the fluid initially in place that can be recovered in that period. The properties of a lean and a rich fluid are represented in a set of integrations designed to demonstrate the effect of different constant-recovery rates and significant variables emphasized one at a time. INTRODUCTION A method is needed for computing the availability or reserve of a gas in a formation, making use of all technical and engineering information that is pertinent. As a step in this direction, a program for computing transient linear flow1 was developed that utilizes principles of earlier finite-difference computing for a similar purpose2-4 and gives effect to significant pressure- and distance-dependent properties of reservoirs and their contents. The present paper pertains to transient, radial flow of gas-condensate fluids. In the partial-differential equation of flow, effect is given to the variables viscosity and compressibility,5 and also to permeability. Included in the study is the quadratic form of the Darcy equation of flow that has been the subject of field tests6 and that has been applied to a gas with constant properties in transient flow computing. 7 Inclusion in the differential equation of variable coefficients to represent properties greatly complicates the higher derivatives of the equation. Because it was impractical to make a required improvement in certain of the finite-difference derivatives by Taylor-series expansion, five-term derivatives were used in the implicit computing. Related methods were developed that can improve general facility in manipulating finite-difference equations. BASIC EQUATIONS PARTIAL DIFFERENTIAL EQUATION The basic partial differential equation for transient radial flow in the direction of decreasing radius is l_ a(vpr) _? .......(1) r gr at where r = radius, L v = apparent velocity aIong radius, L/t p = density, M/L3 t = time, t Ø = porosity, dimensionless. In this equation, only the porosity is regarded constant. The density is where p = pressure, m/Lt2 M = molecular weight of fluid, m T = constant temperature of fluid, T z(p) = pressure-dependent compressibility factor, dimensionless R = gas Constant, mL2/t2t. The physical boundary of the reservoir is at re, and the producing boundary is defined to be at tq with rq = re /200. By definition,

Jan 1, 1966

By William E. Ford, Edward Salisbury Dana

This section includes the common calcium titano-silicate, Tiianite; also a number of silicates which contain titanium, but whose relations are not altogether clear; further the titanate, Perovskite, and niobo-titanate, Dysanalyte, which is intermediate between Perovskite and the species Pyrochlore, Micro- lite, Koppite of the following section. In general the part played by titanium in the many silicates in which it enters is more or less uncertain. It is probably in most cases, as shown in the preceding ages, to be taken as replacing the silicon; in others however, it seems to play the part of agaaic element; in schorlomite (p. 510) it may enter) in both relations.

Jan 1, 1922

By Paul M. Tyler

MILITARY power stems from industrial power and industrial power in turn depends predominantly upon an ample and assured supply of mineral raw materials. It thus becomes the duty of mineral economists to collate the vast array of data and logical deductions in order to reach an unemotional judgment as to the ability of the Soviet economy to withstand the strain of prolonged military action on the modern scale. Russian publications, reports: and official speeches have been laboriously screened and analyzed. Since these are the sources of information for the lower echelons of the Soviet industrial organization itself, they carry factual data that can be pieced together to show the present-day pattern. Apparent contradictions and obvious distortions or omissions can often be rationalized on the basis of observations made by foreign engineers and consultants during the 1930'5 and by checking against the technical literature published before even so-called technical articles were riddled by bombastic and presumptuous claims.

Jan 6, 1951

By K. W. Grubaugh, L. W. Saperstein

The recently enacted federal surface mine law (P. L. 95-87) increases further the complexity of securing a reclamation permit This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the construction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance, and improved cost control.

Jan 1, 1981

By J. T. Ryan

POISONOUS, irritating, or explosive gases are found in almost every industry, and manufacturers of gas masks are called upon to provide gas mask protection for a great variety of conditions, such as operators in horseradish factories, fumigators of homes and ocean liners, and men engaged in the manufacture of tetra-ethyl-lead, the new motor fuel. The modern type of gas mask and respirator, to provide protection against all such industrial gases, is an outgrowth of the gas mask developed during the World War to protect the soldiers against the poisonous war gases. So far, it has been possible to develop ample mask protection from all known noxious gases and fumes present in atmospheres encountered in mines, metallurgical works, and chemical and other industries, so long as there is sufficient oxygen present to support the flame of an oil lamp. The most important development of the gas mask was in providing protection against carbon monoxide- which is the noxious gas that mining men are most concerned with and, in fact, is the noxious gas that man is most frequently exposed to. This paper will be con- fined largely to the discussion of masks for underground use in metal mines. Gases that contaminate the normal air in mines can be divided into two classes: those that are given off normally by the workings, and those that are produced in mine operation.

Jan 1, 1926

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the first half of March: James C. H. Ferguson, San Francisco, Cal. Capt. A. F. Lucas, Washington, D.C. Henry Adams, Stamford, Conn. Dexter P. Cooper, New York, N. Y. H. A. Wheeler, St. Louis, Mo. L. D. Moore, Chatham, N. J. John M. Sherrerd, Easton, Pa. Hennen Jennings, Washington, D. C. R. T. White, formerly General Manager of the Braden Copper Co., Chile, is to take charge of a copper company in Caucasus, South Russia.

Jan 4, 1914

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Apr. 10 to May 10, 1915: William W. Elmer, Tuttletown, Cal. R. R. Freeman, Jr., Wollaston, Mass. Lawrence Addicks, Douglas, Ariz. Francis R. Pyne, Elizabeth, N. J. W. F. Durand, Stanford Univ., Cal. George B. Pickett, Ophir, Colo. S. P. Cooper, New York, N. Y. R. V. Norris has been elected President of the Columbia School of Mines Alumni Association. Robert C. Sticht has been elected President of the Australian Insti¬tute of Mining Engineers.

Jan 6, 1915

By Andrews Allen

WE all remember when, a few years ago the preparation of coal was nothing but a matter of having somebody at the face or somebody in the railroad car pick out the impurities; also the sizes were generally' made" over a bar screen. Anything that was black was coal; and the only matecia1 picked out was the slate or rock-impurities that could be distinguished by eye or by hefting. This was all right as long. & coal could be sold at. a good price. After all, we are all in business to -make the most money honestly out of a certain acreage of coal and a certain plant. For this purpose what is required is the greatest possible recovery of marketable coal and the highest market price.

Jan 1, 1929

Jan 1, 1886

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

Reducing Fusion: The impure or low grade uranium concentrate is mixed with a formulated flux of sodium carbonate, salt, and sawdust or fuel oil and heated, while being stirred, to about 950°C. This reduces the uranium to the black, water insoluble uranium dioxide and with the exception of nonamphoteric metals forms water soluble sodium salts of the vanadium, alumina, silica, phosphates, and other constituents of the cake. The cooled melt is then water leached, leaving a residue of black insoluble uranium dioxide. "Green Sludge" Digestion and Liquor Purification: The green sludge is redissolved in acid, and by selective precipitation involving pH adjustments and a final neutralization

Jun 1, 1956

By FRANK RIEBERS

IN DISCUSSING the selection of a geophysical method, much of what the writer will say is applicable to any of the various methods and to their use in prospecting, whether for oil or for other minerals. Specifically, the writer's subject is the problem, particularly pressing on the Pacific Coast, of checking the rising cost of the discovery of new fields by the proper employment of geophysical methods. Table I was prepared from statistics published by the California State Milling Bureau. The writer selected five of the largest a:ld most active companies operating in California, segregated the number of wild-

Jan 1, 1930

C. Edward Stafford, Chester, Pa.:—Doring all my business life, I have been engaged in the manufacture of Bessemer and open-hearth steels, but, during my long connection with the Shoenberger Steel Co. of Pittsburg, I had some experience in the manufacture of high-grade puddled iron for horseshoes, and in making, by Dr. Otto Wuth's process, extremely pure, low-phosphorus puddled blooms (analyzing from 0.005 to 0.01 per cent. of phosphorus and sulphur), which were melted with low-phosphorus pig-iron in acid open-hearth furnaces, to make extra locomotive fire-box steel. I have also seen the Danks puddlers in operation at different times and places, notably where they were most successful, at the Otis Steel Works, Cleveland, Ohio; then under the management of our friend, Mr. S. T. Wellman. These Danks blooms were made solely for open-hearth melting-stock, to which they were well adapted. (The unavoidable presence of bits of ore-fix imbedded in the mass of the metal always prevents the profitable manufacture of merchant iron from Danks' blooms.) With the experience just described, I was to some degree in position to value fairly the means, methods and results of Mr. Roe's mechanical puddling from the metallurgical or technical and economic points of view, when given an opportunity by Mr. Roe to see his puddling-furnace or machine in operation in Pottstown, Pa. Briefly, the furnace, with water-cooled bottom, is rectangular in plan, about 20 by 8 ft. in the clear, suspended by trunnions at the middle of the long sides, at a height of 17 or 18 ft. above the general level. The oscillation (65" each way from the vertical) is accomplished by geared segments (attached to the downward-projecting side or trunnion-plates) with which engage pinions driven by a reversing engine. The whole section

Jan 1, 1906

By Donald Barton

THIS paper outlines a time-saving graphical method of calculation for application to the interpretation of observations with the Eötvös torsion balance. Preliminary to the treatment of this short cut method which has been found practicable, the principal formu-las by which the student of interpretation can calculate the gradient and differential curvature produced by different types of bodies in different types of situa-tions are presented and discussed. It is necessary to split most geologic bodies into a series of simpler ones for which not too complicated formulas are avail-able. The gradient and differential curvature effects are calculated for each of the simple bodies and then summed to the total effect for the whole body. The calculations are considerable in number and, though more tedious than difficult, should be' entrusted to an experienced calculator. Considerable facility in qualitative interpretation can be acquired by the geophysicist from experience and from a thorough study of the types of gradient and differential curvature anomalies produced by the dif-ferent types of possible structural situations. How-ever, semi-quantitative calculations' of the probable structure bring out many relations that are not evident in a simple inspection of torsion balance results ; it throws out as impossible or improbable certain of the alternative structural possibilities that may seem equally probable under simple inspection of the results; it will determine more accurately the position of the crest of the structure; and reduce considerably the un-certainty in the interpretation and it is necessary to intelligent interpretations. The calculation of such cross-sections consists of a trial-and-error calculation of a body that will give gradient and differential curvature effects as closely as possible the same as those observed. From his knowledge of the gradient and differential curvature produced by different types of bodies, the geophysicist sketches a tentative cross-section of the structure as indicated-to him-by the observed results of the torsion balance survey, and the calculator then splits the struc-ture into blocks, and calculates the gradient and differ-ential curvature block by block. If, as rather usual, the calculated .gradient and differential curvature pro-files diverge considerably from, the respective observed ones, it is necessary to add and subtract blocks from the cross-section until a close agreement is obtained .between the calculated and observed profiles. The com-plete calculations have to be gone through for each block that is added or subtracted.

Jan 9, 1928