Search Documents

By Henry Louis

Henry Louis, Newcastle-upon-Tyne, England (communication to the Secretary*).—In this paper Mr. Simons derives the various forms of revolving slime tables, of which the Harz and the Linkenbach tables are typical examples, from the old rectangular or box buddle. This I believe to be an error, at any rate if Mr. Simons attaches the same meaning as I do to the ((evolution" of a dressing appliance. By the '(evolution" of such an appliance I understand the progressive development and improvement of an appliance acting on a definite principle, such improvements having usually for their object the economy of labor in working the same, or the increase of its capacity; when an entirely new principle is introduced, I no longer look upon this as evolution from the old type, but as the origination of an independent type of appliance. The box buddle was no doubt the predecessor of the old Cornish round buddle, which was evolved from it with the object of saving the labor required to work the box buddle; both machines are horizontal-current separators, in which the separation of sands of different densities is effected by their differential rates of fall in a horizontal current of water of considerable depth. These appliances, though well suited to sands, are for obvious reasons not adapted to the treatment of slimes. The revolving tables of the Harz and similar types, on the other hand, act on the principle which I have called separation in thin films of water, and which Mr. Simons calls the film sizing principle, in which the resistance of the surface over which the pulp flows plays an essential part in determining the separation of the particles, and which is well suited to the treatment of slimes. Unlike the last principle, it will not work in deep bodies of water and cannot be used where considerable depth of material accumulates in the appliance, as in the box buddle and round buddle. As I have shown in my book, The Dressing of Minerals, p. 326, these revolving tables are a development of the appliance known variously as the flat buddle, flat table, or frame, the last name, which is the old Cornish one, being the one that I personally prefer. These primitive appliances, as well as the continuous-acting round tables described by Mr. Simons (his Figs. 10 et seq.) all work on the principle of separation in thin films, and are all adapted for the treatment of slimes; his buddles and round tables (Figs. 1 to 9) do not work upon this principle, and should therefore be sharply differentiated from the former. The evolution in each case of the continuous acting, more or less automatic, circular appliance from the primitive, intermittent, hand-worked, rectangular appliance has proceeded upon strictly parallel lines. The question of the evolution of the respective types involves a point of some importance as regards the principles of ore dressing.

Jan 1, 1915

President MRS THORNS E LLOYD 14 Green Hill Road Morristown, N J First Vice-President MRS A B PARSONS 52 Edgewood Road Scarsdale, N Y Second Vice-President MRS H A PROSSER 1001 Park Avenue New York, N Y Third Vice-President MRS HARRY J WOLF 3 Glenwood Avenue Littleneck, N Y Fourth Vice-President MRS MARK LAWRENCE REQUA 140 North Plymouth Blvd Los Angeles, Calif Fifth Vice-President MRS NEWELL G ALFORD 314 South Homewood Avenue Pittsburgh, Pa

Jan 1, 1952

E. H. Dix, JR., Chairman L. W. M. PEIRCE, Past-chairman R. F. MEHL, Vice-chairman ALBERT J. PHILLIPS, Vice-chairman E. M. WISE, Secretary International Nickel Co., Bayonne, N. J. W. M. CORSE, Treasurer LOUIS JORDAN, Executive Secretary 29 West 39th St., New York, N. Y. Executive Committee W. H. BASSETT, JR. R. H. LEACH' W. H. FINKELDEY W. E. REMMERS2 J. A. GANN H. J. ROAST G. O. HIERS C. S. SMITHS L ZICKRICK

Jan 1, 1936

E. G. SPILSBURY, New York, N. Y.-I would like to ask Mr. Wemple what is the total loss in redistillation; not merely the weight of the lead removed, but also the loss clue to rehandling of a large amount of blue powder, and that clue to the final remelting in the tank furnace? LELAND E. WEMPLE.-The loss of zinc by redistillation, on the first operation, is approximately 5 per cent. This loss does not cover the lead

Jan 4, 1918

By J. S. Ll. Leach, M. B. Bever

THE system copper-nickel exhibits complete solid and liquid miscibility1 The thermodynamic properties of such a system would not be expected to deviate greatly from ideality. Although the evidence is conflicting, anomalies in the composition dependence of various physical properties of solid copper-nickel alloys suggest that mixing may not be ideal.' From measurements of the Hall coefficient it has been concluded that clustering occurs in these alloys. ' Considerations involving the phase diagram of the ternary system copper-nickel-chromium have led Mei-jering3 to predict a positive heat of formation for solid copper-nickel alloys. An electrochemical investigation of the activity of nickel in copper-nickel alloys showed unexpectedly large positive deviations from ideality.4 wagner5 has proposed that if the entropy can be considered ideal, these measurements would yield the following equation for the heat of mixing at 700°C H" = 3380 x,vl (l-xVi) cal per g atom [I1 The heat of formation at 722°C of solid copper-nickel alloys of the equiatomic composition has been measured in a reaction calorimeter as 540 cal per g atom. This note reports calorimetric measurements of the heat effects on dissolution of some copper-nickel ndon: in tin. These measurements were preliminary to a larger investigation, which was later discontinued. From them the heats of formation of the alloys can be calculated, if certain assumptions are

Jan 1, 1960

By F. L. Robertson, C. H. Bacon, J. W. Till

A description is given of the development of a process for making low sulphur steel on furnaces fired with 2 1/2 pet sulphur oil. Slag and metal are analyzed at melt. Slag weight is estimated. A simple method for calculating necessary lime additions for making 0.025 and 0.035 pct sulphur steel is given. DURING the last 15 years John Summers & Sons have been confronted increasingly by the problem of producing a low sulphur steel from high sulphur materials. The principles adopted, the processes used, the data collected on a furnace specially set aside to study this problem, and speculation on future developments are dealt with in this paper. This study is limited to two melting shops which make sheet steel only, of the following analysis: C, 0.06 pct; Mn, 0.33; S, 0.04, 0.035, 0.03, and 0.025; and P, 0.02 and 0.015. All the processes described have reference to the manufacturing of this steel and are not necessarily applicable, without modification, to other steels. The raw materials used are given in Table I. Development of Process About 1934, Schenck's work on phosphorus was applied to frame quantitative rules for the removal of phosphorus, with great success. We could however, neither in our own work nor in the voluminous literature, find any assistance to frame quantitative furnace rules to remove sulphur. Perhaps, we should have persevered with Schenck's outstanding chapter on sulphur in The Physical Chemistry of Steelmaking, but we missed the importance of one (Ss) sentence on p. 478. "Evidently this ratio -------- is [S] the important quantity to be considered from the point of view of chemical reaction; it is clear that the sulphur content of the steel alone, as frequently given in the literature cannot suffice for judging the success of the reaction unless special details are given regarding the sulphur charge and the amount of slag."' We were not however very successful in getting values for Schenck's "n" that agreed with (S) arrived at by our direct analysis. [S] In addition to Schenck's work much attention was given to V value. The formula selected for V was: (SCaO) — 1.57 (2 P2O5) (S SiO2) After plotting many charges a curve was obtained, based upon the relationship between the percentage sulphur in the finished steel and V value, Fig. 1. For a long time this was used as standard with about a 60 to 70 pct success on producer-gas fired furnaces, if all uprising scrap was used and no bought scrap used. An inspection of this curve shows clearly that it is not a quantitative manufacturing process, and that it was not sure enough to go to the trouble and expense of doing stage analysis for P,O,,

Jan 1, 1952

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by [P OL, plotting So = Ao as a function of eo = Lo] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors' It was shown that the true physical behavior of the material in the tension test could best be represented [by plotting the average true stress, S = P as a function of e = q' = log o = log Log] where P, A, L, S, e, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such- curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.' Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor. The nickel sulfide concentrate is leached under pressure with air and ammonia to dissolve the nickel, copper, and cobalt and most of the sulfur, leaving a residue of iron and siliceous material to be discarded.2,3 During a subsequent distillation stage to recirculate part of the ammonia used for leaching, copper is recovered from the solution as a high-grade sulfide. After further purification to remove traces of copper and undesirable sulfur compounds, the nickel is precipitated by hydrogen under pressure at an elevated temperature. The cobalt, together with unreduced nickel, is precipitated as a mixed metal sulfide by hydrogen sulfide for eventual cobalt recovery. The end solution is then evaporated to produce a crystalline ammonium sulfate byproduct. As shown in Fig. 1, the nickel concentrate is leached in a continuous, two-stage, countercurrent circuit. In the first stage, or adjustment leach, the fresh concentrate is partially leached (60 pct) in the liquor produced in the second stage, or final leach. This system is necessary to produce a solution suitable for treatment in the copper sulfide precipitation step. Both stages are carried out at 170" to 180°F under a total pressure, with air, of 100 to 120 psig in large, horizontal, water-cooled autoclaves. The autoclaves are divided by overflow weirs into four compartments to give a certain amount of staging during leaching. In each compartment a relatively slow-speed (100 to 150 rpm) agitator maintains the nickel concentrate in suspension. Adjustment leaching, carried out in two autoclaves in parallel, is followed by a thickener-filter liquid-solids separation. Final leaching is done in two parallel trains of three autoclaves using aqueous ammonia to extract metal values from the adjustment leach residues. This too is followed by a thickener-filter circuit. Here the residues are repulped once with aqueous ammonia and twice with process water and refiltered after each repulping stage, to insure a maximum recovery of soluble metal, before being discarded to the tailings pond. The adjustment leach is followed by a seven-disk Dorr-Oliver American filter, with an agitator in the filter boot to keep the residues in suspension. Agitators have also been installed beneath the four ten-disk filters following the final leach thickener. Slurry Characteristics: A typical analysis of the Lynn Lake nickel concentrate, produced by differential flotation,' is given in Table I. The concentrate comprises 35 to 49 pct pentlandite, (Fe, Ni)S; 3 to 6 pct chalcopyrite, CuFeS,; 1 to 4 pct pyrite, FeS2; and 24 to 42 pct pyrrhotite, Fe1-2S (where x varies between 0 and 0.2) together with various siliceous minerals such as actinolite, hornblende, and talc. During leaching, the sulfur in the pentlandite, chalcopyrite, and part of the pyrrhotite is successively oxidized through the thiosulfate and poly-thionate radicals to sulfate and sulfamate." Simultaneously the nickel, copper, and cobalt are converted to soluble ammine complexes and the iron in the pentlandite, chalcopyrite, and part of the pyrrhotite is oxidized to a spongy hydrated iron oxide. The hydrated iron oxide is readily broken down by the agitation needed to sustain the concentrate in suspension and to maintain a satisfactory mass transfer of the oxygen from the air to the slurry. Table I shows typical chemical, screen, and

Jan 1, 1961

By C. G. Durdaller, W. H. Robinson, G. M. Pound

The nucleation rate of the a (pay) to 0 (white) tin transformation was measured as a function of temperature and a tin particle size using an X-ray diffraction technique. The powder specimens of a tin were essentially monodisperse and the small dinzension of the particles of these specimens was varied from 13 to 75 p. Several types of nucleation sites of differing potency were fbund to be operative in the nucleation process, but it could not be determined whether these sites were on the free surface of the tin particles or within the volume. Assuming that they were on the free surface, the average density of the most potent sites was calculated to be 2.5 to 5.3 x 10' sites per sq cnz through the application of a Poisson distribztion finction to the isothermal data. Analysis of the temperature dependence' of the rate constmts at a given fraction transformed suggests that the active sites are regions of higher free energy and not catalytic interfaces. Appreciable induction periods were observed at the lower temperatures of transformation. Experimental studies1 of solid-solid phase transformations have led to the belief that the new phase nucleates at structural imperfections. The purpose of the present work was to learn more about the mechanism of nucleation in solids and the nature of the singularities at which nucleation occurs. In this investigation nucleation rates in the isothermal transformation of gray to white tin were measured by an X-ray diffraction technique using essentially monodisperse powders of gray tin. This particular phase transformation was chosen for study because it presented fewer experimental difficulties than most others. The experimental temperature-control problems were minimal because the two phases coexist in equilibrium at 13.3"C, and measurable transformation rates occur at temperatures only slightly above room temperature. The growth rate of the P phase into the a2 is sufficiently fast to make the measured transformation rate equivalent to the nucleation rate, provided that the particle size of the samples is small enough; for the experimental temperatures used in this study, the particle diameter must be less than 100 p. EXPERIMENTAL TECHNIQUE The P tin used in this study was obtained from Capper Pass and Son Ltd., North Ferriby, Yorkshire, England, and was of 99.999 pct purity. It was transformedS to the a phase and ground into a fine powder in an agate mortar. This powder was separated by a Roller air classifier into seven fractions whose dimensions, as determined by microscopic measurement of many thousands of particles, are given in Table I and whose distribution of size within each fraction is given in Figs. 1 and 2. The shape of the particles was roughly that of an oblate spheroid,

Jan 1, 1964

Discussion of the papers of Dorsey A. Lyon and Samuel S. Arentz, p. 789; S. E. Bretherton, p. 802; H. A. Wentworth, p. 809; and Richard D. Drvine, p. 814. GeoRge W. RiteR, Salt Lake City, Utah.—We have every reason to believe that oil flotation will soon come into general use as a final guard against slime losses in concentrating mills, not only in the case of zinc ores, but also in the case of other semi-precious ores. It also promises much as a primary process for the concentration of minerals that are not adapted to gravity methods. Moreover, modifications of the process involving selective or preferential flotation are gradually becoming understood, and will make it possible to eliminate pyrite and other minerals occurring as undesirable impurities in zinc concentrates. And what perhaps is of equal importance, further modifications promise an effective method of separating zinc blende from ores that are chiefly valuable for copper, lead, and precious metals, thereby making an asset out of zinc which has heretofore been a liability. The tendency of certain pulverized minerals to float on water, especially after having been in contact with grease, has been known to mill-men for a long time, and was formerly something to be deplored and to be striven against. All at once, this tendency has become a saving grace; and now, like tardy converts to a new faith, we are zealous advocates of something we once despised. I was once employed at a mine in the Tintic mining district of Utah— the old Eureka Hill property—where ores that were too low in value to warrant being sent to copper or lead smelters were treated in a combination mill. The ores contained gold, silver, lead, copper, zinc, manganese, arsenic, etc., in varying quantities and in varying mineral forms, mingled in a quartz and calcite gangue. The material was stamped fine and then concentrated on Frue vanners so as to make a smelting concentrate, after which the tailings were thickened and treated in amalgamating pans for the recovery of non-concentratable precious metals. In the amalgamating pans, under the influence of heat and agitation, a dark greasy froth or scum sometimes formed on the surface of the ore mixture. This froth or scum was composed mainly of mineral sulphides, and its occurrence might have meant only casual losses in the previous concentration, except that the phenomenon was accompanied by faulty amalgamation of the precious metals and by excessive losses in the mill tailings. Grease and oil, present by accident, were the cause of the trouble. Whether the intense vibration in the mill, due to the pounding of the heavy stamps, had caused small particles of grease to be shaken loose

Jan 1, 1915

D. F. HEWETT, Washington, D. C. (communication to the Secretary*).-I am not prepared to discuss the metallurgical use of manganese in the form of alloys. In connection with other work for the U. S. Geological Survey, however, I have been investigating incidentally, for about 5 years, the American as well as other sources of manganese. There are some conclusions that come out of this investigation that may interest those whose greatest interest lies in the use of the alloys. From a geological point of view, most manganese ore deposits may be regarded as concentrated masses of manganese oxides, as there are few masses of the other manganese minerals that are rich enough in manganese and low enough in silica to warrant smelting. The deposits of the Huelva district, in Spain, which are largely manganese carbonate and silicate, are exceptions to this statement. Some deposits of manganese oxides, such as those of Russia and Cuba, are bedded with ancient sediments, and although they are clearly concentrated under unique conditions, the source of the manganese cannot be determined. Probably 60 per cent. of the world's production of manganese ore, or 95 per cent., if that of Russia be excluded, is derived from the superficial parts of deposits that have undergone weathering and enrichment near the surface. In other words, the situation with the manganese ore supply is such as it would be with regard to copper, if instead of being derived largely from deep zones of deposits of deep-seated origin, such as veins, it were derived solely from the zone of secondary enrichment. Manganese oxide occurs in all rocks but is most abundant in igneous rocks, of which, according to Clarke, it forms an average of 0.10 per cent. It also forms 0.05 per cent, of the average limestone, but only traces are present in shales and sandstones. It is interesting that although many commercially important manganese deposits occur in rocks that are but slightly richer in manganese than the average, the most important deposits occur in rocks of unusual character that are much richer in manganese than the average. Thus, the most important deposits of India and Brazil overlie or occur near masses of rocks that contain excessive amounts of manganese garnet and pyroxene.

Jan 5, 1917

By D. J. Schmatz, H. I. Aaronson, H. A. Domian

Diffusion kinetics in disordered hcp Cd-Mg alloys have been investigated by means of the Kirkendall effect and concentration-penetration curves determined with an electron-microprobe analyzer. Self-diffusion coefficients of both species were determined at the three marker compositions obtained, averaging 27.6, 46. 7, and 78.1 at. pct Mg, by means of the Darken analysis. These coefficients were then corrected for the unequal and concentration-dependent partial molar volumes of the two elements with the Balluffi analysis, and for the vacancy flux effect by the Manning analysis. The latter correction reduced the Balluffi correction produced larger changes in the self-diffusiv-ities; neither, however, produced statistically significant changes in the Do's or the H'S. The most striking result of this investigation is that at all three compositions and at all temperatures studied both the uncorrected and corrected self-difjusivities of magnesium are higher than those of cadmium. The Cd-Mg system is the first one found in which the higher melting, lower vapor pressure element diffuses more rapidly. Both an empirical correlation due to Toth and Searcy and considerations of the atomic mechanism of diffusion indicate that this anomaly is probably due to a comparatively low value of the activation energy required for a magnesium atom and a vacancy to exchange sites, perhaps occasioned by the higher compressibility of magnesium atoms. KIRKENDALL effect studies have been previously reported for only two hcp solid solutions: the E phase of the Zn-Cu system1 and the a phase of the Cd-Hg system.' In neither investigation were the marker-movement studies supplemented with the concentration-penetration curve determinations necessary to evaluate self-diffusivities by means of the atano and the Darken analyses. The present program was undertaken to obtain both types of data on a hexagonal solid solution in order to provide more detailed information relevant to the mechanism of diffusion in this type of lattice. The Cd-Mg system was chosen for this study because the disordered solid solution extends across the entire phase diagram at temperatures above 253"c5 and the substantial difference in the melting points of the component pure metals promised that marker movements would occur at reasonably rapid rates should the diffusivities of the two species be as unequal as might be anticipated. The experimental convenience of the relatively low melting points of cad-miun and magnesium and the availability of extensive and accurate activity data6 (required for application of the Darken analysis) were additional reasons for selecting this alloy system. Since the anisotropy of diffusion is not large in either pure cadmium7 or pure magnesium,' the diffusion couples were prepared from polycrystalline components. The presence of a well-defined texture in the couples—the c axis of individual crystals tended to be normal to the diffusion direction— however, provides a fair degree of crystallographic definition to the data obtained. The principal (and entirely unexpected) finding of this investigation, that magnesium, the high-melting low-vapor pressure element, diffuses more rapidly than cadmium, in contradiction to a broad range of results in fcc and bcc alloys, as well as in the previously studied hcp alloys,172 makes the self-diffusivity determinations of immediate interest in understanding the origin of this anomalous result. EXPERIMENTAL PROCEDURE The cadmium (Belmont Smelting and Refining Co.) and magnesium (Dow Chemical Co.) used in this study were both of 99.99 pct purity. Alloys containing 51.0 and 65.6 at. pct Mg were prepared from these materials by melting under a MgC12-base flux in a high-purity graphite crucible. These alloys were subsequently hot-worked and then homogenized in a helium atmosphere at temperatures close to their solidus points. Sandwich-type diffusion couples of the type g/d/g were prepared from the pure metals by solid-state diffusion. Two-piece alloy couples of Mg/65.5 at. pct Mg (Mg/gCd) and Cd/51.0 at. pct Mg (Cd/CdMg) were welded by a liquation technique. The individual components of both types of couple were initially cylinders 1.27 cm in diam and in length; the ends of these cylinders were machined accurately flat and parallel. For both welding techniques, the pure cadmium cylinders and the alloys were chemically polished in a mixture of 40 pct ethyl alcohol, 40 pct hydrogen peroxide (30 pct conc), and 20 pct nitric acid,g while those of pure magnesium were polished in a solution of 10 pct nitric acid in ethyl alcohol.' Immediately afterwards, both metals were rinsed in freshly distilled acetone, and then in similarly purified methanol.' The Mg/Cd/g couples were assembled in a carefully cleaned stainless-steel welding fixture, in which a screw operating through a self-centering arrangement permitted a controlled pressure to be exerted upon a couple prior to welding.'' Tungsten marker wires 0.005 cm in diam were placed at the d:g interfaces of some of these couples, and imbedded in the couples during the application of pressure. As soon as a couple had been assembled, the welding fixture was inserted into a Pyrex capsule containing a packet of zirconium chips at each end. The capsule

Jan 1, 1967

[ZAY JEFFRRIES, Vice-chairman PAUL D, MERICA, Chairman W, M, CORSE, Secretary Executive Committee J. It, FREEMAN, JR., Local Section S. SKOWRONSKI, Papers Committee R. S, ARCHER, Non-ferrous Data Sheets H, C, JENNISON, Membership Committee E, C, BAIN, Journal Committee L, W. SPRING Local Section Committee J. R, FREEMAN, JR,, Chairman R. J, ANDERSON, Cincinnati R. L. DOWDELL, Minneapolis R. S. WILLIAMS, Boston G, H, CLAMER, Philadelphia W. A. SCHEUCH, Chicago R, F, WOOD, New York]

Jan 1, 1928

By E. T. Turkdogan, J. H. Swisher

bi the fivst part of the paper results ave given on the rate of decarburization of Fe-C melts ln CO2-CO atmospheres at 1580°C. The rate -controlling step is believed to he that irvlloluing dissociation of curbotz dioxide on the suvfuce of the melt. 4 genevral reaction mechanistm is poslnlated jor gels-t11eta1 veactions oc-curit~g on the surface of iron coutcotamncited with chemi-sovbed osygesL. Oxygen the present work on decavbuvization of liquid iron and previous studies on the kinetics of nitrogen absorption and desorplion are discussed in terms of the postulated mechanism, ManY of the early studies of rate of decarburization of liquid steel were of an exploratory nature and laboratory exppriments carried out pertained to open-hearth or oxygen steelmaking processes. References to previous work on this subject may be found in a literature survey made by Ward. Using more sophisticated experimental techniques, several investigators have recently studied the kinetics of decarburization of molten Fe-C alloys in oxygen-bearing gases. For example, Baker et al2.' reported their findings on the rate of decarburization of liquid iron, levitated by an electromagnetic field, in carbon dioxide-carbon monoxide-helium atmospheres. In these levitation experiments the samples used were small in size, e.g., -0.6-cm-diam spheres weighing -0.7 g, and the rates were measured for decarburization from about 5 to 1 pct C at 1660°C. The rates obtained under their experimental conditions were considered to be controlled primarily by gaseous diffusion through the boundary layer at the surface of the levitated melt. Parlee and coworkers3 measured the rate of absorption of carbon monoxide in liquid iron. The rates were found to follow first-order reaction kinetics, yielding a reaction velocity or a mass transfer coefficient in the range 0.2 to 0.4 cm per min. The coefficient was found to decrease with increasing carbon content of the melt. These investigators attributed the observed rates to the transfer of carbon or oxygen through the diffusion boundary layer adjacent to the surface of the melt. In the work to be reported in this paper, an attempt has been made to study the kinetics of gas-metal surface reactions involved in the decarburization of liquid iron. EXPERIMENTAL The experiments consisted of melting 80-g samples from an Fe-1 pct C master alloy in an induction furnace and decarburizing in controlled CO2-CO mixtures at 1 atm pressure and 1580°C. The master alloy was prepared by adding graphite to electrolytic "Plastiron" melted in racuo. None of the impurities in the master alloy exceeded 0.005 pct. The reacting gases were dried by passage through columns of anhydrone; in addition, CO2 impurity in carbon monoxide was removed by passage through a column of ascarite. A schematic diagram of the apparatus is shown in Fig. 1. A 1.25-in.-diam recrys-tallized alumina crucible containing the sample was placed inside a 3-in.-diam quartz reaction tube, all of which was surrounded by an induction coil. A 450-kcps induction generator was used as the power source. Water-cooled brass flanges, which contained the gas inlet, gas exit, and sight port, were sealed to the top of the reaction tube with epoxy resin. The reacting gases were metered with capillary flowmeters and passed through a platinum wire-wound alumina preheating tube, 0.25 in. ID and 11 in. long. The gases were preheated to about 1300°C. A disappearing-filament optical pyrometer was used to measure the melt temperature. The pyrometer was initially calibrated against a Pt-6 pct Rh/Pt-30 pct Rh thermocouple. The temperature was controlled to within +10°C by manually adjusting the power input to the induction coil. In a typical experiment, an 80-g sample of the master alloy was melted in a CO2-CO atmosphere having pcO2/pco = 0.02 and flowing at 1 liter per min. A negligible amount of carbon was lost and no significant reduction of alumina from the crucible occurred during melting, e.g., 0.005 pct Al in the metal. After reaching the experimental temperature of 1580°C, the gas composition was changed to that desired for a particular series of decarburization experiments. The duration of the transient period for obtaining the desired gas composition at the surface of the melt was about 20 sec . The flow rate of the reacting gas was maintained at 1 liter per min. After a predetermined reaction time, the power to the furnace was turned off. During freezing, which took about 10 sec, the amount of gas evolution was not sufficient to result in a significant loss of carbon. The samples were analyzed for carbon by combustion and in a few cases they were analyzed for oxygen by the vacuum-fusion method. RESULTS A marked increase in the rate of decarburization of iron with increasing pcO2/pco ratio in the gas stream is demonstrated by the experimental results given in Figs. 2 and 3 for pco2/pco ratios from 0.033 to 4.0. In one series of experiments, denoted by filled triangles in Fig. 2, the reacting gas was diluted with argon (48 vol pct) resulting in a slower rate of decarburization. Samples from two series of experiments with pco2/pco = 0.033 and pco2/pco = 0.10 (with argon dilufion) were analyzed for oxygen. In these Samples the oxygen content increased with reaction time

Jan 1, 1968

Jan 1, 1883

By Satyajeet Ghosh, Edward F. Glynn

Many of the proposed techniques for calculating the reliability of rock slopes utilize Monte Carlo simulation. Monte Carlo approaches are attractive because they provide means of solving probabilistic problems with deterministic algorithms. One disadvantage shared by all simulation-based stability analyses is that they assume all the random variables are independently distributed. The paper focuses on the independence assumption and examines the effect of correlation on the probability of failure. In particular it considers the influence of possible (albeit hypothetical) correlation between joint attitudes [(8)] and joint friction angles [($)]. The study indicates that neglecting correlation can introduce significant errors into the reliability computations. With a modest positive correlation between [8] and [$] the error can lead to a 100% overestimate of the probability of failure.

Jan 1, 1982

By AIME AIME

A CERTAIN area in the State of Indiana seems to be a breeding place for presidents and near president about eighteen miles southeast of Elwood is the little village of Daleville, and there, on April 9, 1890, John Robert Suman, newly elected President of the A.I.M.E., was born. It was not long before he migrated to California, however, where he went to the Los Angeles High School, then for two years to the University of Southern California, after which he went up to Berkeley

Jan 1, 1940

By Glenn A. Marsh, George Bernard

It is often assumed that aerated oil field brines which are to be injected underground contain dissolved oxygen in amounts which will cause appreciable corrosion. Through the use of a new portable dissolved oxygen meter, accurate determinations were made at three brine conditioning plants. At two older plants, dissolved oxygen concentration in the final treated brine was found to he almost zero In spite of aeration during the conditioning process. At a new plant, dissolved oxygen was initially present but disappeared soon after the brine was "inoculated" with oxygen-free brine from one of the other plants. Corrosion tests at the two older plants have substantiated predictions that the brines would lint be corrosive. These results show that mechanical deaeration may not always be required in brine treating plants. INTRODUCTION The present work was undertaken to add to our knowledge of aeration and deaeration of oil field brines in brine conditioning plants. It is commonly assumed that brines which are exposed to the air soon become more or less saturated with dissolved oxygen. Since oxygen-containing brines are known to be corrosive, precautions are often taken to keep air out of brine through the use of closed systems or mechanical deaeration. The study of oxygen in brine has been seriously hampered in the past because of the lack of a suitable analytical tool. The standard Winkler method for the determination of dis-solved oxygen is satisfactory for use in fresh water, but not in many oil field brines. Corrections have to be made for a number of reducing substances such as ferrous iron and hydrogen sulfide which are commonly present in natural brines. Very often the correction factors are much greater in magnitude than the amounts of oxygen which are to be determined, and consequently erroneous results are obtained. Also. erratic Winkler data are obtained when appreciable concentrations of calcium and magnesium salts are present. The first step in carrying out a systematic study involved designing a portable dissolved oxygen apparatus which would operate in natural brines. Subsequently, this apparatus was used in three brine conditioning plants. Dissolved oxygen data obtained here, and certain corrosion rate data, illustrate the interesting behavior of oxygen in these oil field brines. APPARATUS A portable dissolved oxygen meter described in detail elsewhere,' was developed specifically for use with oil field brines. It is a polarographic apparatus employing a small rotating platinum electrode (cathode) and calomel reference electrode (anode). A potential of 0.7 volts is applied across the electrodes while they are immersed in the brine to be tested. 4References given at end of paper.

Jan 1, 1952

By Charles Hart

THE-report of the advisory committee to the U. S. Bureau of Mines, on the use of oxygen in metallurgy, brings to the art of steelmaking a radical change in the method of operation of the many processes of this widely diversified industry. When completed, the improvements suggested by the use of oxygen will be far-reaching and revolutionary. As to its effect upon the iron blast furnace, the use of oxygen should be as important as any of the improvements in the art of iron smelting and should take its place beside the German "Hochofen" which was the first attempt to use a shaft for preheating the stock, and beside the hot-blast stove which heated the blast before entering the furnace. The former initially produced molten iron and the latter made unbelievable economies in fuel consumption. It would seem that a discussion of this paper would be best served by following the conclusions on page 17 of the report and analyzing them seriatim. 1. (a) A decrease in costs, due to higher smelting heats is only attainable by taking full advantage of these heat units. This is affected by, adding additional ore to the burden which in turn increases production and yields a larger tonnage upon which to figure costs. These economies appear in decreased cost per ton of iron for coke and limestone consumed, and a proportionate reduction in all items entering the cost above materials. We can take no exception to these. premises. It is a well-known fact that silicon in the iron and sulfur removed" are the result of hearth temperature, other matters remaining constant. To a practical furnaceman the most satisfactory manner of controlling a furnace is by increasing the burden. It is not necessary, therefore, to consider the question of refractories, for this discussion presupposes that the temperatures in the furnaces will be kept practically where they now stand for making the various grades of iron. The same situation obtains in regard to the height of the furnace, which, as intimated, was one of the great strides forward in this art, and its abandonment at this time, is inconceivable. The shaft prepares the stock so that at each succeeding step we have exactly the proper conditions. All the stock entering the furnace is dried and preheated. The limestone is calcined by sensible heat practically at no cost, for this is sensible heat which otherwise would pass from the top with the gases. Under normal conditions, external calcination has been attempted without tangible results. Under normal average furnace operation, limestone requires about 760 B.t.u. for calcination and the loss of sensible

Jan 11, 1924

By C. M. Moncrief, B C. Craft

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946