Search Documents

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5'7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

By E. G. SINCLAIR

DRILLING wildcat wells in Wyoming differs a little from methods used in any other field. Here it is always advisable to start the hole as large as is convenient in order to carry each string of pipe as far as possible, so that drilling can be continued a thousand feet deeper if necessary, as there is always sand a few hundred feet ahead that really ought to be tested. This plan may seem ambitious, but if it is adhered to, it will save a great deal of trouble before the well is completed. In making the location, one representative from the operating department and one from the geological department should work together, so that the well may be in the best possible place for obtaining oil and the most feasible place to drill for the operating department. In Wyoming nearly all wells are drilled with standard tools, as with them a better log can be kept and better time made in completing the hole. The shales of Wyoming are very hard and do not mix well in a wet hole. The shale cuts into large pieces, too large to be circulated out of the hole, and forms a mat on the rotary which soon cuts off circulation. Then if this mat cannot be jarred from the bit, the drilling string has to be pulled and the mat cut off from the bit with a pick or an axe. I have seen standard tools come out of a wet hole with 10 to 16 in. of mat on the bottom of the bit. Rotary tools have drilled wells satisfactorily in the Big Muddy field and at Billy Creek, but in the other fields the wells have been drilled much more economically with cable tools.

Jan 1, 1926

By F. T. Davis

Many contributors have added to the fund of knowledge in the basic sciences related to mineral dressing during the past year. During 1964, the French edition of the Proceedings of the VIth International Mineral Processing Congress together with discussions was printed. Also, complete Preprints of papers delivered at the VIIth IMPC were published in September1. Over a third of the papers presented at VIIth IMPC dealt with fundamentals. COMMINUTION It has been postulated by Ponceleta that flaws need not exist before a stress is applied but rather the flaws are created at the tip of a propagating crack at a stress well below the theoretical breaking stress.

Jan 2, 1965

By B. D. Cullity

A distribution of residual stress after plastic elongation is proposed, in which the bulk of the material is strained in compression and a very small portion in tension, This distribution is shown to account both for the X-ray observations and for the effect of plastic straining on magnetic losses in silicon steel. The regions left in compression are tentatively identified with the interiors of the sub-grains revealed by the electron microscope. THIS paper is concerned with the general problem of the nature of the residual stress which is produced in metals by plastic elongation. A particular stress distribution will be suggested which accounts for the main X-ray diffraction observations which have been made. It will also be shown that certain magnetic measurements made on silicon steel can be understood in terms of this stress distribution. X-RAY OBSERVATIONS Uniform straining of a crystal lattice (macro-strain) causes a diffracted X-ray beam to shift its position, and nonuniform straining (microstrain) causes line broadening. If a bar of metal is plastically elongated in the longitudinal x direction and then unloaded, diffracted X-ray lines are observed to be both shifted and broadened.'-= Although the observed line shift indicates the presence of macro-strain, experiments have shown that no macrostrain, in the usual engineering sense of the term, exists.5"7 For example, removal of a layer from one surface of a stretched and unloaded bar does not produce curvature in the remainder of the bar 5'7 Fig. 1 shows the variation of lattice strain in the x direction, as determined from X-ray line shifts, with the applied stress in the same direction. The curve ABC is the normal stress-strain curve of the material, AB being the elastic portion and BC the plastic. In the elastic region AB, the strain measured by X-rays, called the lattice strain, and the strain measured mechanically are both proportional to the applied stress, and both return to zero when the applied stress is removed. Above the elastic limit the lattice strain would be expected to continue to increase along the line BD. Actually, it increases less rapidly with respect to stress, or even decreases, as shown by BE. If the applied stress is then decreased, the lattice strain decreases along EF, which is parallel to AB. As a result, there is a compressive residual lattice strain FA after unloading. STRESS DISTRIBUTION. Since a stretched and unloaded bar does not contain macrostress, it follows that the observed line shift must be due to a special distribution of mi-crostress. Such a distribution is shown in Fig. 2, which shows the variation of the stress u, across a stretched and unloaded bar. The material is assumed to consist of two kinds of regions: regions C, stressed more or less uniformly in compression, comprising the bulk of the volume of the material and responsible for the observed diffrac-

Jan 1, 1963

By E. D. Peters

It frequently occurs in the establishment of reduction works, in an entirely new and untried mining district, that the metallurgist in charge finds considerable difficulty in determining the process best adapted to the ores which he receives for treatment. At the first glance it would seem easy enough to decide what style of furnace is best adapted for beneficiating any one class of minerals. If the ore possessed a quartzose gangue and was comparatively free from base metals, while salt could be obtained at a reasonable price, one would naturally resort to a chloridizing roasting, and pan or barrel amalgamation for the extraction of its silver contents. If galena or carbonate of lead was the prevailing mineral, and charcoal could be obtained at moderate figures, the blast-furnace would beneficiate the ores most advantageously. But if, as is usually the case in Colorado, the ores consisted of an intimate mixture of galena, zinc-blende, copper-pyrites, and noble silver minerals, associated with an overwhelming mass of siliceous heavy spar, or limestone gangue, the common reverberatory furnace can be used to the greatest advantage ; and, although the product is only a copper matte, I do not hesitate to affirm that it can be treated, and the silver, gold, and copper produced at nearly the same price for which silver and lead can be separated. In Germany, blast-furnaces are frequently used for this same purpose, both for argentiferous and non-argeutiferous copper ores; but any one who will take the trouble to examine the statistics of smelting at Fahlun, the Oberharz, and other Continental works of this description, will see that the expenses are far too great, and the production much too small to think of employing this method in our mining districts, where only the softest and most miserable kind of charcoal is obtainable. I propose in this paper to give an accurate account of the expenses incurred at the Mount Lincoln Smelting Works in treating the same kind of ore, and producing the same end-product in both blast and reverberatory furnaces. I have taken for comparison a favorable campaign of the blast-furnace, and a good average month's running of the reverberatory. In the blast-furnace estimate I have included the calcining and concentration of the matte produced during that campaign, as I always, when possible, concentrated the regulus made

By HOMER L. WILLIAMS

WHILE some of the mining companies have been pumping a small amount of water for some time, it is only in recent years that large quantities of water have been encountered in the Tonopah district. The water appears to be in different zones or belts so that the draining of one property does not necessarily affect the one adjoining. Consequently, each company has its own pumping plant and its own conditions. The companies panes handling the largest amount of water are the Tonopah Extension Mining Co., Halifax Tonopah Mining Co., West Tonopah Consolidated Mining Co., and Great Western Consolidated Mining Co. The Halifax shaft is on the eastern end of the district and the other three properties on the western. The ore-bearing formation occurs at greater depth on -the eastern and western ends, hence the water problem in these properties.

Jan 1, 1921

By Stephen Krickovic

AS it is commonly understood in the bituminous coal mining industry, pillaring means removal, as completely as is practical, of all pillars formed in the development of headings and rooms on first mining. The degree to which this can be accomplished, termed percent of recovery, is of course dependent generally upon the physical conditions of the bottom and the overburden, the system of min-

Jan 1, 1956

By Charles F. Park

Mining in the Pacific Coastal Region has passed through three stages of development. First came the gold rush days, a period when gold and silver were the objects of intensive search. Second was the development of the high-grade base-metal deposits and of the smaller and more refractory precious metal deposits. And third was the modern period that covers the discovery and development of the rarer metals, of large low-grade deposits, and of the industrial and nonmetallic minerals. Brief discussions of the salient geologic features of the region and of a few of the better known mineral deposits are given. The regional geology is favorable for continued exploration and discovery of new deposits and districts.

Jan 1, 1968

By Ove Sandberg, Olav Bowitz

The operational characteristics of the Soderberg vertical spike anode are briefly discussed stressing the importance of the flow properties of paste in the fluid zone, the thermal shrinkage in the carbonizing zone, and the surface disintegration in the consumption zone. The requirements for paste recipe and binder quality are combined with design and operation of cell. A low temperature susceptibility of viscosity and low thermal shrinkage of paste together with a low microporosity of the binder coke are important properties. PRACTICAL application of Soderberg's idea of a selfbaking carbon electrode proved successful just before 1920. Shortly after, experimental work was started with the aim of developing a continuous electrode that could be adopted as anode in aluminium reduction cells. The intermittent operation of a large number of small prebaked anodes made the idea of developing a continuous anode for electrolytic production of aluminium especially tempting. Moreover, the electrode consumption in this process, even on a theoretical basis, is very high. Many installations were carried out in the 1930's and during the Second World War. During the tremendous post-war expansion of the aluminium industry, the Soderberg electrode has been steadily more widely adopted. Thus, today more than 60 pct of the Western World's output of aluminium is produced in cells with selfbaking anodes, see Big. 1. The quality of the anode paste of Sfiderberg elec- trodes is considered a major factor influencing the specific carbon consumption. The purpose of this paper is to survey the fundamental requirements which must be met in order to obtain good anode operation. We have limited this paper to a discussion of Elektrokemisk's research on the vertical spike type anode. I) FUNDAMEKI'TALS OF ANODE CARBON PERFORMANCE A) Brief Introduction. The only practical method for producing a conductive carbon anode of the size required is to form and carbonize a mixture of a carbonaceous binder and a precalcined dry aggregate coke. In the Soderberg electrode, the forming and carbonization take place in the electrolytic cell

Jan 1, 1962

By Charles Morgan

AN increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2).

Jan 1, 1937

By Thomas F. Donnelly

The Province of San Cristobal is situated on the south side of the island of Santo Domingo about 25 miles west of Santo Domingo city, the capital of the republic. The copper mineraliza,tion is found about 8 miles north of the town of San Cristobal,. in the section known as Bucaro Hill; in San Francisco Hill; on the Nigua River; and on the Jaina River. The district is reached by automobile from Santo Domingo city over an excellent road for 25 miles to San Cristobal, and then, by horseback 6 or 8 miles up the Nigua River to what is locally known as "Camp

Jan 1, 1916

By Dick Whittington, W. R. Taylor

GENERAL In mid-1974, a representative of ARCO Petroleum Company walked into our Austin offices and asked for a permit for ARCO's first Clay West Mine site. This was the first in situ uranium mining permit issued in the United States. That initial permit, issued in January 1975, was for three acres. The four years since have been characterized by growth and change. Today there are 16 permits approved for approximately 1,540 production acres issued to five companies at eight sites in four counties. There are approximately seven additional permit applications being processed or on the verge of being submitted for an estimated 2,000 additional acres of production. As a rough gauge of the financial scope of this activity, at the typical 40 production wells per acre and an estimated $2,000/well, operators hale installed or committed $122 million for production wells. This does not account for the exploration and development wells installed to delineate the ore or the cost of processing facilities for extracting the uranium. HISTORY OF URANIUM MINING IN TEXAS Information I have concerning early in situ uranium mining activities is "sketchy" but the apparent first on-site test of in situ uranium mining was conducted between 1967 and 1971 at the Dueterstat site, north of Yorktown in Gonzales County, by City Service. Others ran tests at the Bruni site in Webb County and the Burns and Clay West sites in Live Oak County in the mid-70's. During this period, Texas Water Quality Board personnel in the central and district offices maintained a general surveillance of these various test activities. Regulation of in situ uranium mining was formalized with the issuance of a permit in January 1975 with the advent of ARCO's initial production scale (3 acre) effort in the Clay West area at the Moser mine site. Since 1975, the accelerating rate of mining and exploration activity is noticeable. There were 16 exploratory rigs operating early in 1977. This year, the rig count is averaging 46--a 287% increase. HISTORY OF LEGISLATION Paralleling this mining activity was state and federal legislation which subjected in situ mining to environmental regulation. The following is a brief chronology of the legislation that is directly or indirectly related to uranium mining. As most of you know, disposal wells are an integral part of most in situ uranium mines operating in Texas. They are used both during production and during aquifer restoration following production. The wells are regulated by the Texas Injection Well Act, enacted in 1961 by the Texas Legislature. In 1967, the Water Quality Act established the Texas Water Quality Board, and provided for the regulation of water quality by the so-called permit system. In 1969, the Solid Waste Act was enacted by the Texas Legislature. The legislation provides for control of wastes from manufacturing, mining, and agriculture. This Act regulated uranium surface mining activities until 1975 when the Texas Surface and Mining Reclamation Act placed responsibility with the Railroad Commission for uranium open-pit mining and surface mining of coal and lignite. In 1972, the Federal Water Pollution Control Act (Public Law 92-500) was passed. This legislation forms the legal base for the NPDES (National Pollutant Discharge Elimination System) and the subsequent point source effluent guidelines and standards. The November 6, 1975 issue of the Federal Register published interim final rules for Best Practical Treatment levels for effluent discharges from ore mining and dressing operations. Litigation was immediately initiated by eleven companies against these proposed rules, and they are currently being reconsidered for reissuance in 1979. In 1974, the Federal Safe Drinking Water Act (Public Law 93-523) was enacted. A part of this legislation is the Underground Injection Congrol Program. The regulations implementing this program have undergone various public hearings and it is expected that they will be published in the Federal Register before the end of 1978. In 1975, the Texas Surface Mining and Reclamation Act (Senate Bill 55), providing for the Railroad Commission's authority to require reclamation of surface mines, was passed. In 1977, an amendment to Senate Bill 55 was introduced that proposed to place regulation of in situ mining of coal, lignite, and

Jan 1, 1979

The University of North Dakota, State Geological Survey, Grand Forks, N. D A G. Leonard, State Geologist. Two publications of the State Geological Survey are of interest Fourth Biennial Report, The clays and clay industries of North Dakota, and Bulletin 4, Lignite deposits and lignite industries of North Dakota. Bulletin 11 of the University is of interest: Geology and natural resources of North Dakota For further information, address the above

Jan 1, 1933

By C. G. Dunn

NUCLEI that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,1 that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclassesf of the 36 third- order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of de- formation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a {110} plane in a < 100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is notparticularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1946

William H. Blauvelt, Syracuse, N. Y.:—Is the coal itself from which the briquettes are made of good quality for steam-ing-purposes? Mr. Parker :—It is an anthracite coal mined near Bank-head arid used on the Canadian Pacific railroad. It contains about 83 of carbon, 8 of ash, and 8 per cent. of volatile material. With regard to briquetting of a mixture of fine coal and coke-dust, I understand that a plant has been installed near Detroit in which coke is mixed with anthracite; also the plant of the United Gas Improvement Co. near Philadelphia is briquetting a mixture of anthracite coal, the resultant briquettes being used in the gas-retorts. Mr. Blauvelt:—The purpose of the Detroit briquette-plant of the Solvay Process Co. has been partly to use up the coke-breeze from the by-product ovens and partly to utilize the pitch. There is no necessity for mixing anthracite with the coke-breeze, but the supply of breeze is limited, and anthracite

Jan 1, 1909

MINING METHODS W. J. COULTER, Chairman P. B. BUCKY, Vice-Chairman CLYDE E. WEED, Vice-Chairman ROBERT S. PALMER, Secretary Alluvial Mining CLINTON BERNARD O. B. FERRY NORMAN CLEAVELAND C. M. ROMANOWITZ R. B. EARLING J. B. STAPLER BENERE H. GRANTCHARLES THURMAN

Jan 1, 1944

By W. B. Triplett, H. I. Aaronson, G. M. Andes

THE morphology and mechanism of the proeutectoid a and the eutectoid reactions have been recently investigated in some detail in an iodide-base Ti—7.22 pct Cr alloy.&apos; These studies have now been extended to an iodide-base Ti—10.8 pct Cr alloy in order to evaluate the effects of composition on the proeutectoid and eutectoid transformations in titanium-chromium alloys. The alloy used in this investigation had the following composition: 10.8 Cr, 0.0327 0, 0.011 N, 0.0063 H, and 0.011 pct C. Specimens of this alloy were heat treated in evacuated and internally get-tered Vycor capsules. The specimens were solu-

Jan 1, 1959

COLORADO LOCAL SECTION Executive Committee CHARLES A. CHASE, Chairman S. A. IONIDES, Vice-Chairman C. LORIMER COLBURN, Secretary-Treasure, 614 Ideal Bldg., Denver, Colo. F. H. BOSTWICK, W. G. SWART. The annual meeting of the Colorado Local Section of the Institute was held at the Savoy Hotel, Denver, Jan. 15.- The Chairman, Frank Bulkley, presided and made a short address on the work of the Section. The following officers were elected:

Jan 3, 1915

By Lawrence A. Soltis

Senior engineering or executive management positions are filled by engineers who are evaluated on their performance, knowledge, skill, and maturity. Not only is technical expertise required but a knowledge of sales and marketing, finance, law, industrial relations, and public affairs is necessary. The University of Wisconsin-Extension offers an innovative post-baccalaureate degree program blending technical and professional subjects the Professional Development Degree in engineering (PDD)-designed to bring various opportunities for learn-

Jan 4, 1978

By Burt C. Mariacher

Extraction of uranium from ores is being accomplished by processes which, for the most part, subject the entire ore to acid or carbonate leaching. Ore deposits with a U3O8 content below 0.10 pct U3O8 are seldom considered suitable for treatment by leaching. A preliminary concentration that would enrich the uranium content of an ore by a simple, low cost process based on physical properties of the ore might result in some low grade deposits becoming commercial ores. In addition, the process might be employed in existing operations to reduce transportation and leaching costs and to increase capacity of existing leaching plants.

Oct 1, 1956