Search Documents

By B. C. Craft, Murray F. Hawkins, John R. Rayne

A reservoir mechanism of sulfur recovery by the Frasch process is presented. Improving the economic, of recovery appears to be largely a well, rather than a reservoir problem. A most important factor is the limitation of the lateral extraction of .sulfur about the wells due to the almost vertical .flow of the injected hot water. Model studies are described which confirin the mechanism of sulfur recovery by presently used methods. Studies on a five-spot system indicate improved econo171ics regarding recovery, recovery rate, therinal efficiency, and well spacing. INTRODUCTION Sulfur mining by the Frasch process is one of the most important methods of sulfur production. Developed by Herman Frasch in 1894, it enjoyed a rapid growth and presently supplies 40 per cent of the world's sulfur and about 80 per cent of the U. S. sulfur." The Frasch process of mining the underground native sulfur deposits involves melting the sulfur in place by introducing super-heated water into the sulfur bearing formations, and producing the sulfur as a liquid. Many problems are encountered in mining these native sulfur deposits, and sulfur production depends chiefly upon the nature of the sulfur deposit and the underground thermal efficiency of the heat transfer system. THE RECOVERY MECHANISM Sulfur is typically found in salt dome cap rock as crystal aggregates occurring within the cavities, seams, and pores of limestone and gypsum formations.' Sulfur-bearing limestone is typically cavernous, vugular, and fractured. Porosity averages about 20 per cent and sulfur saturation averages approximately 25 per cent by weight.1,15 Vhe sulfur bearing formations are very heterogeneous in nature and physical characteristics vary widely within small distances. Total cap rock thickness may vary from 50 to more than 1,000 ft, and net productive thicknesses from a few feet to a few hundred feet. In most cases the upper portion of the limestone formation is barren of sulfur, varying from 5 to 200 ft in thickness.1,15,33 The immediately overlying sediments and the underlying dense anhydrite formation provide permeability barriers to the flow of water from the cap rock section.'" Sulfur wells are drilled with conventional oilfield drilling rigs. Fig. 1 illustrates the casing program of a completed sulfur well. The cap rock sections are drilled with core bits and continuous core logs are recorded. After coring, the cap rock section is underreamed to a diameter of 9 7/8 in. The bottom of the 8-in. casing is welded closed and rests on the bottom of the drill hole, which extends through the cap rock to a few feet above the bottom of the sulfur-bearing formation. The 8-in. pipe contains 5 ft of 3/4-in. perforations on 6-in. centers and 15 ft of 1-in. perforations on 1-ft centers. The 20-ft perforated section is set opposite the lower 20 ft of the sulfur-bearing formation. The 4-in. sulfur pipe is set inside the 8-in. water line on a seat ring at the top of the 5-ft section of 3/4-in. perforations. The mining water, heated to about 330°F under a pressure of 250 psi, is forced down the annulus between the 8-in. and 441-1. pipes and through the 1-in. perforations to the sulfur-bearing formation. Compressed air, at 400 psi pressure, is supplied through a 1-in. air line near the bottom of the well to provide air-lift of the liquid

Jan 1, 1957

By Frank Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper, wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength; consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig.1 was drawn.

Jan 1, 1928

By W. E. Howlett, R. L. Slobod

Jan 1, 1965

By AIME AIME

COAL occupied a large place in the technical sessions of the Institute at its annual meeting for in addition to three sessions specifically de- voted to coal the two sessions on mine ventilation and the two on ground movement and subsidence, which are reported under their own headings, were primarily concerned with coal. The first session on coal was a joint one with the Iron and Steel Division, on Wednesday afternoon, with F. H. Crockard and J. R. Campbell presiding as joint chairmen and the latter actually officiating. The principal topic of discussion was G. S. Scott's paper "Evaluation of Coal for the Making of Blast- Furnace Coke," which has been published as T. P. 159. The author made a brief statement of its con- tents to start the discussion and the chairman, after briefly reviewing it himself, called on C. A. Meissner to start the discussion. He briefly reviewed the economic factors in the use of coal for coke-making, saying that not only .does the removal of 1 per cent of ash from the coal reduce the cost of pig iron 12 or 13c. per ton, but it also permits coke of satisfactory structures to be made from a coal which otherwise could not be used. He stressed the importance of uniformity in blast-furnace fuel and discussed the benefit of mixing different coals as raw material for the coke oven and cited experience with Illinois coals.

Jan 1, 1929

By J. D. Braun, C. W. Powell

Diffusion between gold and indium at two temperatures below the melting point of indium (155.4oC) was investigated. The major, component of the diffusion zone was determined to be AuIn2; the other, intermediate phases in the system occur in much narrower layers In order of decreasing layer width these are: Au9In4, AuIn, Au4In. Inter diffusion coefficients of the four intermediate phases and the terminal solid solutions lie in the range of 2.4 x 10-l3 to 1.8 x 10-11 sq cm per sec. WHEN two metals which do not form a continuous series of solid solutions interdiffuse, each phase in equilibrium at the diffusion temperature should appear as a separate layer in the diffusion zone. In the Au-In system, diffusion plays a significant part in many commercial applications, particularly where indium alloys are used as solders for electrical contacts with very fine gold wire, for estab- lishing electrical contact to thin metallic films, and for mounting metal-coated piezoelectric crystals. A knowledge of the number, extent, and type of phases which form at diffusion temperatures below the melting point of indium, 155.4oC,1 and the diffusion constants for the system would be useful for these practical applications. Of more basic significance, additional information on polyphase diffusion in a system not previously investigated would be gained. The phase relationships in the Au-In system were determined primarily by Kubaschewski and Weibke1 and are based on thermal, microscopic, and X-ray analysis, Fig. 1. There are five intermediate phases in the system having approximate compositions corresponding to the formulas: Au4ln (ß)—80.0 at. pet Au; Au3In (?)— 75.0 at. pet Au; Au9In4 (d)—69.2 at. pet Au; AuIn—50.0 at. pet Au; AuIn2—33.3 at. pet Au. Solid solubility of indium in gold at 700°C is reported as 12.64 at. pet and at 406°C as 10.36 at. pet. No solid solubility of gold in indium is reported.

Jan 1, 1964

By W. R. Ingalls

In reviewing the history of the metallurgy of zinc, I shall pass hastily over what is only of antiquarian interest. That has been excellently treated by Dr. Bernhard Neumann in "Die Metalle" (1904) and has been described briefly in my "Production and Properties of Zinc" (1902), in my "Lead and Zinc in the United States " (1908), and in other metallurgical works of more or less the same date. In this present monograph, I have it in mind to confine myself mainly to technical practice, especially to that of the last 75 years, prior to which period advance was slow and of no great moment. The ancients made brass by the cementation process, i.e., embedding copper in a mixture of calamine and carbon and heating, whereby zinc oxide was reduced and zinc was vaporized and combined with the copper. Zinc was isolated by some of the alchemists, who named it and knew something of its properties, but made no use of it. Long before then, however, zinc was produced in India. Later it was produced in southern China. Possibly the Chinese obtained their knowledge from India. The Chinese in remote places still produce small quantities of zinc. I have seen photographs of their furnaces; or pots, for they hardly deserve the dignity of being called furnaces. I imagine that they are the same that were used centuries ago, for I cannot conceive of anything more primitive. Anyway, it is certain that the idea of a commercial production of zinc in Europe was imported from the Orient, where the metal was known in commerce as Speauter and Spiauter, whence speltrum and finally our term spelter. Tutanego and Tuteneague are other old names. Dr. Isaac Lawson went to China about 1730, expressly to discover the method of its production. What connection there was between Isaac Lawson and John Champion we do not know, but the latter obtained in 1739 a patent for a process of distillation downward and at some time between 1740 and 1743 erected a works at Bristol and actually began the manufacture of spelter. A production of 200 tons per annum is mentioned. In about the year 1766, Rishop Watson visited the Champion works and saw the process in operation, which previously had been

Jan 1, 1937

By Robert F. Mehl

EXTENSION of physical and chemical methods of research in the study of metallic behavior continues rapidly, particularly in the correlation of behavior with crystal structure, and in the analysis of elastic and plastic properties. The growth of the science of metals during 1933 calls for special comment; the need for special reviews and for textbooks and monographs is now acute, as might he supposed from the number of references appended to this article, a list which is much abbreviated.

Jan 1, 1934

By Floyd Kelley

THE literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be util-ized to the fullest extent there must be a thorough investigation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibrium produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizing1 which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure.

Jan 1, 1928

By H. W. Gillett

Unlike most previous Howe lecturers, I had not the good fortune to be associated with Henry Marion Howe, nor to be directly one of his students. Yet, through his writings, he has been my teacher, as he has of all American metallurgists. Instructive as his writings are—I use the present tense because Howe thought so keenly and reasoned so surely, seeing clearly, as if by intuition, what was hazy to lesser minds, that his writings are still vital—it is not those books and papers, nor even the minds he trained in his classes, that were his most outstanding service. It was the spirit of Howe in his approach to the problems of metallurgy, his broad-mindedness and fairness, his recognition of the need for theories and hypotheses to explain metallurgical phenomena, his willingness to use them as servants, as well as his questioning attitude—his refusal to accept them as masters—that comprise his greatest service. This most thoroughly warrants the honor the Institute pays each year to his memory. These traits I so respect and honor in any man that I glory in this opportunity to do reverence to him in whom they were so notably united. Howe's Discussion of a Creep Problem I have often wished that Howe were still with us to turn his keen insight upon the problems of the use of metals at high temperatures, a field much studied but still very hazy. Indeed, 53 years ago, in a paper1 before this Institute, Howe stated a problem closely allied to some that still perplex metallurgists and engineers dealing with the high-temperature field. Howe was intrigued by a report2 from another old master, Robert Henry Thurston, on the behavior of annealed vs. cold-drawn iron wire, and in order to broaden the foundation for metallurgical generalization, Howe made experiments of his own on copper and silver. In these tests by Thurston and by Howe, the wires were rapidly loaded to determine the

Jan 1, 1939

By Frank W. Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength, consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig. 1 was drawn.

Jan 1, 1928

By A. C. Fieldner

In November, 1926, the American Engineering Standards Committee (now the American Standards Association) called a meeting of representatives of various professional societies and industrial, educational and governmental organizations to consider what action, if any, should be taken on the classification of North American coals. This meeting was called because a system for the use classification of coal, proposed by George H. Ashley, had been referred to the committee by the Coal Mining Institute of America. This meeting, at Pittsburgh, was well attended and was definitely in favor of taking up the whole question of scientific and use classification of coals, including all the various ranks from lignite to anthracite. The American Society for Testing Materials was recommended as the sponsor organization to take charge of the work and organize the sectional committee according to the rules of the American Standards Association. The American Society for Testing Materials proceeded with the organization of the sectional committee, holding a meeting in Philadelphia, June 10, 1927. Officers were elected, regulations adopted, and general plans for carrying out the work were outlined. The total membership of 28 comprising the sectional committee consists of 8 producers, 2 distributors, 9 consumers and 9 members representing general and scientific interest. From this committee three technical committees of 10 to 12 members each were organized: Scientific Classification, H. J. Rose, chairman; Use Classification, W. H. Fulweiler, chairman; Marketing Practice, F. R. Wadleigh, chairman. The Technical Committee on Scientific Classification was requested to formulate a system of coal classification based on chemical and physical properties of coal and with reference to origin and constitution. The Technical Committee on Use Classification was charged with developing a system of classification, if possible, based primarily on the uses of coal and commercial practice; this system to be correlated with the scientific system as far as possible and desirable. The Technical Commitlee on Marketing Practice was formed to collect and collate information on commercial practice for the benefit of the other two committees. The first meetings of the technical committees were held on Nov. 17, 1927, and the first informal progress reports were submitted to the

Jan 1, 1930

By P. Pietrokowsky

RECENTLY a comprehensive investigation of the various sigma binary alloys was published by Duwez and Baen.1 It was shown that the following conditions are necessary for the formation of the sigma phase: (1) the difference in atomic diameters of the two alloying metals must not be more than about 8 pct; (2) of the two elements which form sigma, one must exhibit a body-centered cubic structure while the second metal must be face-centered cubic, at least in one of its allotropic forms. In addition, a tetragonal unit cell was proposed and powder patterns of six sigma phases were indexed for d spacings greater than 1.640 kx. Since the indexing, based on tetragonal symmetry, led to only fair agreement, the possibility of sigma being orthorhombic was investigated. Various methods for indexing orthorhombic powder patterns are de- scribed in the literature.' The method used in this investigation was a graphical examination of the differences in values of sin' 9 for the adjacent lines of the powder diffraction pattern. This method led to a complete indexing of the Cr-Co (60-40) pattern. Because of the strong similarity between the various sigma alloys, it was then possible to assign indexes to the patterns of Fe-Cr (50-50), Fe-Cr-Mo (30-30-40), Fe-V (50-50), Co-V (50-50), and Ni-V (50-50). The values of sin' 9 and indexes of the six sigma alloys, together with visually estimated intensities, are presented in table 1. In general, the similitude between the six patterns is quite good. For spacings greater than 1.75 kx a few differences are noticeable. In the Ni-V pattern, no (320) exists and the two strong lines (030) and (031) are separated by only two lines of lower intensity, unlike any of the other sigma patterns. However, very little is known about the Ni-V phase diagram and it is possible that the equal atomic percentage composition in this system lies in a two-phase region. At lower spacings there is a close analogy between the patterns. The planes

Jan 1, 1951

By John W. Wagner, Robert K. Willardson

Single crystals of Pbl-xSnxTe have been grown from nonstoichiometric, cation-rich melts with the objective of producing as-grown, bulk material containing carrier concentrations ranging from 1016 per cu cm to 1018 per cu cm. Three specific crystal composi-tions were investigated in detail; x = 0.00, 0.10, and 0.17. Pull rates of from I to 3 mm per hr were used. Single crystals were successfully pulled from melts containing as little as 30 at. pct Te. Hall coefficients, resistivities, and carrier mobilities of these materials were determined. The relationship between the composition of the melt and the carrier concentration in the as-grown crystal has been studied for the three crystal compositions of interest. BULK single crystals of Pb,-,Sn,Te have previously been grown from stoichiometric melts.1,2 Such crystals are p-type and have relatively high carrier concentrations ranging from -9 x 1018 per cu cm for PbTe to -8 x l020 per cu cm for SnTe at 77°K. These carrier concentrations result from deviations from stoichiometry (lead vacancies) in the as-grown crystals. Since lower carrier concentrations are desirable for electrooptic device applications, these crystals are usually subjected to long-term, isothermal anneals.' This paper reports on the growth of Pbl-xSnxTe single crystals from nonstoichiometric melts with the primary objective of producing as-grown material containing relatively low (1016 to 1018 per cu cm) carrier concentrations and also reports on the general characteristics of these crystals. The phase relationships in the Pbl-xSnxTe systems are such that materials solidifying from nonstoichiometric, cation-rich melts will have smaller deviations from stoichiometry than materials grown from stoichiometric melts. Fig. 1 is the T-x phase diagram for PbTe in the vicinity of the stoichiometric composition.3 A crystal grown from a stoichiometric melt will solidify at a melting point maximum at which the solid will contain -0.5002 atom fraction of tellurium. PbTe single crystals grown in our laboratories from stoichiometric melts have carrier concentrations of 9 x 10" per cu cm, indicating that the excess tellurium in the crystals is as expected from this phase diagram. However, growth of PbTe from a lead-rich melt will result in material having a more nearly stoichiometric composition. Although the addition of Sn to the melt shifts the solidus curve further toward the tellurium-rich side,4 the general discussion given for PbTe applies to the Pbl-xSnxTe systems as well. EXPERIMENTAL Single crystals of Pb1-xSnxTe have been grown in our laboratories from nonstoichiometric, cation-rich melts using the Czochralski technique and boric oxide liquid encapsulation. The details of the growth apparatus and growth technique have been reported in a previous paper on growth of these alloys from stoichiometric melts.2 In the present study, three specific crystal compositions were investigated in detail; x = 0.00, 0.10, and 0.17. Growth of alloy crystals from nonstoichiometric melts requires considerable care, and good quality single crystals were obtained in this study only by optimizing the mechanical and thermal stability of the growth system and by using pull rates of from 1 to 3 mm per hr (Pbl-xSnxTe crystals are easily pulled from stoichiometric melts at rates of from 5 to 10 mm per hr). The liquid encapsulation technique was found to yield near-ideal conditions, since the B2O3 layer increased the thermal stability at the growth interface, permitted easy attainment of near-ideal thermal gradients, and dampened vibrations at the melt surface. The hygroscopic character of the B2O3 was a slight problem and vacuum heat treating was necessary to completely remove the water from the boric oxide. During initial growth, the seed diameter was reduced and a narrow neck (1 to 2 mm diam) of several millimeters length was grown. The latter steps were found to be necessary for the growth of single crystals, i.e., if either of these two requirements were

Jan 1, 1970

By Floyd C. Kelley

THE literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be utilized to the fullest extent there must be a thorough investigation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibrium produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizing1 which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure. DIFFUSION OF METALS IN IRON It seems to be a general law, whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, that a comparatively rapid, or abnormal, grain growth results. The grains

Jan 1, 1928

By Raymond B. Ladoo, C. A. Stokes

Bruce C. Netschert—It is unfortunate that the authors of this paper consider it necessary to begin with an expression of concern over possible false interpretations of the word "economics." In their preoccupation with the definition of economics, they have adopted a definition of mineral economics which is, to say the least, unduly narrow. Just as the broad field of economics is not confined to a study of the profitability of business concerns, but includes the problems of production, distribution, and consumption as they pertain to society as a whole; so an inclusive definition of mineral economics should not be confined to the determination of the profitability of mineral-producing and processing enterprises, but should include the significance of the unique characteristics of mineral resources as raw materials for the use of society. Such features as the exhaustibility and localized, haphazard occurrence of deposits, the existence of a secondary (scrap) supply, and the increasing cost of operation during the life of a mining enterprise are obviously factors which concern those businesses which are producing mineral raw materials, since they partially determine the profitability of such enterprises. They are also of concern to society as a whole, however, as characteristics of one of the basic elements of the economic system. In the last analysis, the contribution which mineral economics can make as a means of determining and guiding social policy with respect to the production and utilization of mineral resources is perhaps more important than its use as a basis for determining the cost accounting procedure of individual firms. The list of "economic factors peculiar to the industrial minerals" which the authors present is in reality an application of such a broad definition of mineral economics. An inconsistency appears, however, in the inclusion of items 8 and 9 in the list. As this writer sees it, the point in question is: What influences do the characteristics of industrial minerals have on the characteristics and operating procedures of industrial mineral enterprises which are not present in the metallic mineral field? In answering this question with items 8 and 9, Messrs. Ladoo and Stokes do not recognize that there are two distinct types of differences between the two fields of enterprise. There are, on the one hand, important basic economic distinctions due to inherent economic characteristics of industrial minerals which do not pertain to metallic minerals. On the other hand are those characteristics of the industrial mineral enterprises peculiar to them alone, but which are superficial and temporary, in that they may be changed or eliminated at the discretion of the managers of those enterprises. The lack of adequate research and development in industrial mineral production, processing, and marketing (item 8) is not due to an inherent characteristic of industrial minerals. It is true that one may perhaps describe the field of industrial mineral enterprise in terms of such a deficiency, just as one could, until recently, point to a similar lack of research and development in the coal industry; but unless it can be shown that the deficiency has been wholly or partially due to the very nature of industrial minerals themselves it is not an "economic factor peculiar to the industrial minerals" but a temporary characteristic peculiar to the industry. In the writer's opinion, the authors have not demonstrated that the former relationship exists. Similarly, item 9, the "influence of technologic developments," is also not inherently peculiar to industrial minerals. Nowhere in the discussion of this item do the authors mention anything that is not equally applicable to the field of metallic minerals. This is not meant to imply that the specific technologic developments which the authors list are of equal significance in both fields. It does mean that such a statement as, "technological advances together with new consuming areas to provide markets make deposits commercially valuable which once were of no interest" cannot be considered as an argument that technological developments have significance in the field of industrial minerals alone. In considering the problem of stockpiling, the authors note that the stockpiling of nonstrategic materials might be desirable if future wartime needs could exceed domestic production capacity, but dismiss this as hardly adequate to justify such stockpiling. The problem, however, can be stated in broader economic terms, i.e., the real costs (as distinguished from the money costs) of prewar versus wartime production. In other words, it might well be that the labor and capital required to produce a given amount of a certain mineral raw material could be used more efficiently in another industry. In such a case it is obviously advantageous to stockpile the material in prewar times rather than forego the benefits of additional production in another line of endeavor during wartime under conditions which demand the optimum use of all resources, including manpower and capital. To the writer's knowl-

Jan 1, 1951

By Raymond B. Ladoo, C. A. Stokes

Bruce C. Netschert—It is unfortunate that the authors of this paper consider it necessary to begin with an expression of concern over possible false interpretations of the word "economics." In their preoccupation with the definition of economics, they have adopted a definition of mineral economics which is, to say the least, unduly narrow. Just as the broad field of economics is not confined to a study of the profitability of business concerns, but includes the problems of production, distribution, and consumption as they pertain to society as a whole; so an inclusive definition of mineral economics should not be confined to the determination of the profitability of mineral-producing and processing enterprises, but should include the significance of the unique characteristics of mineral resources as raw materials for the use of society. Such features as the exhaustibility and localized, haphazard occurrence of deposits, the existence of a secondary (scrap) supply, and the increasing cost of operation during the life of a mining enterprise are obviously factors which concern those businesses which are producing mineral raw materials, since they partially determine the profitability of such enterprises. They are also of concern to society as a whole, however, as characteristics of one of the basic elements of the economic system. In the last analysis, the contribution which mineral economics can make as a means of determining and guiding social policy with respect to the production and utilization of mineral resources is perhaps more important than its use as a basis for determining the cost accounting procedure of individual firms. The list of "economic factors peculiar to the industrial minerals" which the authors present is in reality an application of such a broad definition of mineral economics. An inconsistency appears, however, in the inclusion of items 8 and 9 in the list. As this writer sees it, the point in question is: What influences do the characteristics of industrial minerals have on the characteristics and operating procedures of industrial mineral enterprises which are not present in the metallic mineral field? In answering this question with items 8 and 9, Messrs. Ladoo and Stokes do not recognize that there are two distinct types of differences between the two fields of enterprise. There are, on the one hand, important basic economic distinctions due to inherent economic characteristics of industrial minerals which do not pertain to metallic minerals. On the other hand are those characteristics of the industrial mineral enterprises peculiar to them alone, but which are superficial and temporary, in that they may be changed or eliminated at the discretion of the managers of those enterprises. The lack of adequate research and development in industrial mineral production, processing, and marketing (item 8) is not due to an inherent characteristic of industrial minerals. It is true that one may perhaps describe the field of industrial mineral enterprise in terms of such a deficiency, just as one could, until recently, point to a similar lack of research and development in the coal industry; but unless it can be shown that the deficiency has been wholly or partially due to the very nature of industrial minerals themselves it is not an "economic factor peculiar to the industrial minerals" but a temporary characteristic peculiar to the industry. In the writer's opinion, the authors have not demonstrated that the former relationship exists. Similarly, item 9, the "influence of technologic developments," is also not inherently peculiar to industrial minerals. Nowhere in the discussion of this item do the authors mention anything that is not equally applicable to the field of metallic minerals. This is not meant to imply that the specific technologic developments which the authors list are of equal significance in both fields. It does mean that such a statement as, "technological advances together with new consuming areas to provide markets make deposits commercially valuable which once were of no interest" cannot be considered as an argument that technological developments have significance in the field of industrial minerals alone. In considering the problem of stockpiling, the authors note that the stockpiling of nonstrategic materials might be desirable if future wartime needs could exceed domestic production capacity, but dismiss this as hardly adequate to justify such stockpiling. The problem, however, can be stated in broader economic terms, i.e., the real costs (as distinguished from the money costs) of prewar versus wartime production. In other words, it might well be that the labor and capital required to produce a given amount of a certain mineral raw material could be used more efficiently in another industry. In such a case it is obviously advantageous to stockpile the material in prewar times rather than forego the benefits of additional production in another line of endeavor during wartime under conditions which demand the optimum use of all resources, including manpower and capital. To the writer's knowl-

Jan 1, 1951

By R. E. Somers

I. Introduction...........................604 1. Location, Topography, and Climate...............604 2. Scope of Work and Acknowledgments...............606 3. History and Mining......................606 11. General Geology.........................609 1. Introduction...........................609 2. Granite. :..........................610 3. Quartz Porphyry......................... 612 4. Monzonite........................... 614 5. Volcanic Breccia........,................ 618 6. Gravels............................. 619 111. Economic Geology......................... 619 1. Introduction........................... 619 2. Mineralogy........................... 619 3. Occurrence of the Ores...................... 622 4. Oxidation and Downward Enrichment............... 630 5. Rock Alteration........................639 6. Genesis of the Ores........................ 643 I. Introduction 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant county. The group is made up of two distinct mountain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy downpour of rain. The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 1, 1916

By Ogden B. Malin

In conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructures of several compositions under various conditions of working were examined in an effort to establish this as a fact. Survey of Previous Work in Studying Extrusion Defects Very little has been published concerning defects in extruded and forged brass. In 1921, R. Genders1 $ delivered a paper before the British Institute of Metals, relative to a defect inherent in the extrusion process. This defect, commonly found in extruded brass rod, shows up in the form of a circle in a transverse section consisting of oxides and impurities, and is generally present in the last 25 to 30 per cent of the rod. Genders concluded that the defect is caused by the turning inward of the skin of the billet at the edge of the plunger because the inside of the billet is more plastic than the outside, which is in contact with the cooler container; the outside skin will lag behind to form the rear end of the rod. Genders suggested a movable die as a remedy, and while this met with fair success, it is not used in present practice. About the same time as Genders' experiments, Tucker2 and Rosen-hain3 conducted experiments using colored plasticene in the form of a billet, and found much the same defect as Genders. Dr. Rosenhain State College, Pa.

Jan 1, 1932

By Eugene Stephenson

IN most instances the fluids produced from underground reservoirs have been described as they appear at the surface, and usually it has not been necessary to distinguish between surface and reservoir phases. More recently it has become imperative to recognize the fact that changes in phase may occur between the reservoir and the receiving unit. The simple terminology of "wet" and "dry" gases and "crude petro-leum oil" served our needs fairly well in the shallow, low-temperature and low-pressure fields. It has been left to the legislatures, regulatory com-missions, and courts to decide whether a field is or was a gas field, an oil field, or both. This they have done by direct definition and also by implication. For example, in Texas:1 (d) The term "gas well" is any well (a) which produces natural gas not associated or blended with crude petroleum oil at the time of production, or (b) which produces more than one hundred thousand (100,000) cubic feet of natural, gas to each barrel of crude petroleum oil from the same producing horizon, or (c) which produces natural gas from a formation or producing horizon productive of gas only encountered in a well bore through which crude petroleum oil is also produced through the inside of another string of casing. (e) The term "oil well" is any well which produces one (1) barrel or more of crude petroleum oil to each one hundred thousand (100,000) cubic feet of natural gas.

Jan 1, 1938

By F. A. Crossley

The additions: o, Sn, Zr, Cb, Mo, and V were studied for their effects on the a/a + Ti3A1 boundary of Ti-A1 base ternary alloys. These additions were chosen because of their importance to commercial titanium alloy practice—oxygen as the major impurity (in terms of influence on mechanical properties) and the others as major alloying additions. The composition and temperature ranges of investigation varied according to the system as shown in Table I. The principal means of investigation was light-microscopy. The basis of the ternary studies was the recently determined titanium-rich end of the Ti-A1 system.' MATERIALS, METHODS, AND PROCEDURES Ingots were prepared in 15 g size for all alloys except those of the Ti-Al-Mo and Ti-A1-V systems which were prepared in 20 g size. These alloys were prepared from high-purity, electrolytically refined titanium obtained from the Bureau of Mines, Boulder City Metallurgical Laboratory, Boulder City, Col., and Chicago Development Corp., Riverdale, Md., for the 15 g and 20 g ingots, respectively. The alloying additions were obtained from commercial sources, and were at least of 99.9 pct purity, except the V-15 wt pct A1 master alloy for vanadium additions. This alloy was of 98.2 pct purity; the major impurities were 0.37 wt pct Fe and 0.38 wt pct Si. The ingots were prepared by multiple melting in a nonconsum-able-electrode arc furnace. The ingots were covered with Markal coating "CR-T22" (Markal Co., Chicago) to protect them from scaling. Markal coating is applied as a slurry of solids in a volatile carrier liquid. The coated article is air dried. Upon heating to the hot working temperature the coating fuses to form a glassy, protective film. The ingots were heated to 1000°C and rolled to 0.16 in. thickness, reheating after each pass. The glassy film was removed by sand blasting. Ten mils were removed from all surfaces by grinding and/or pickling (3 pct HF, 30 pct HN03, balance water). Grinding was always followed by pickling to remove traces of the grindmg medium. Hydrogen removal was accomplished by vacuum annealing at 1000°C for 2 hr to a final pressure of about 0.02 µ Hg. This was followed by annealing in evacuated Vycor bulbs (800°C, 2 hr, ice brine quenched (IBQ)) in order to maximize ductility. The materials were then lightly pickled and cold rolled to 0.12 in. thickness or cracking, whichever occurred first. After rolling, 1/2 by 1/4 in. specimens were cut for the equilibration anneals given in Table 11 and carried out as previously described.1 Final polishing of the specimens for metallographic examination was done by electrolytic means. Specimens were first examined without etching under bright field and polarized light illumination, for this is the only means of detecting the "two-phase" phenomenon.1,2 The term "two-phase syndrome" refers to Ti-A1 al-loys which appear on the bases of their chemical, phys-ical, and mechanical properties, to be two-phase, but are actually single phase and inhomogeneous in composition. Since processing and heat treatment of the alloys of the first group were completed before the two-phase syndrome was discovered, a number of the specimens were found to exhibit this phenomenon—80 pct of those of the Ti-Al-Zr system, 5 pct of those of the Ti-Al-Sn system, 30 pct of those of the Ti-Al-Zr system. The affected specimens were homogenized by heating above the ß transus temperature and quenching. The heat treatment and working schedules to accomplish this are given in Table 111. After rolling, specimens were pickled (3 pctHF, 30 pct HNO3 in water) to remove 1 to 2 mils from the

Jan 1, 1970