Search Documents

By A. Kounosu, T. Fujita, J. Shimoiizaka, K. Nakatsuka

Stable aqueous dispersion of magnetite colloid of about 10 nm in diameter was obtained by allowing an anionic or nonionic surfactant to adsorb on the hydrophobic surface of magnetite particles prepared by monomolecular adsorption of oleate. Sodium dodecylbenzene sulfonate, sodium oleate and poly (oxyethylene) nonyl phenyl ethers whose hydrophilic-lipophilic balance (HLB) are higher than 12 were suitable for giving a second adsorption layer to obtain a stable dispersion. Stability of the colloidal suspensions depends upon pH of the solution and is controlled by the dissociation of the adsorbed surfactant in the second layer. The addition of ethyleneglycol, which was used for lowering the freezing point of the dispersion, did not affect the stability when used in amounts smaller than 60% of water. Preparation of diester-based ferrofluids was also attempted by the same procedure using a nonionic surfactant as second layer molecule. Hydrophobic magnetite colloid, which had been preliminarily coated with mono-molecular oleate, was suspended in di(2-ethylhexyl) agipate, azerate, and sebacate respectively, and dispersion stability was investigated by adding various poly (oxyethylene) nonyl phenyl ethers of different HLB values. It was found that those with HLB values between 10.9 and 13.3 were suitable for this purpose. Stabilities of the dispersions in a magnetic field were investigated up to 1 T by applying an electromagnetic field. No separation of dispersant was observed and each magnetite dispersion displayed the characteristics of a magnetic fluid.

Jan 1, 1980

By T. V. Philip, Paul A. Beck

IN a previous note1 it was pointed out that the available information suggests a distinct correlation between the occurrence of the CsCl-type ordered structures formed in equi-atomic binary alloys of transition elements and the location of the components in the periodic table. A definite increase in the bond strength between unlike atoms, as compared with that between like atoms, is indicated when, in binary alloys of iron group elements, the other component is changed from chromium to vanadium or tantalum, to titanium. Laves and Wallbaum,2 eported a CsCl-type ordered structure for the stable intermediate phase at the equi-atomic composition in the Ti-Fe system (and also in the Ti-Ru and Ti-Os systems). On the other hand, Tagaya, Nenno, and Nishiyama8 found no ordering of this kind in the body-centered-cubic solid solutions in the Cr-Fe system. It was concluded' that the occurrence of a CsC1-type ordered phase of intermediate stability may be expected in the V-Fe system. Preliminary results were described: suggesting that at least some degree of order does exist in the equi-atomic alloy VFe, annealed at 1200° C and quenched in cold water. Using CrK radiation, at least one weak superlattice line was found in the X-ray diffraction pattern which could be indexed as (100). and which disappeared, as expected, when FeK radiation was used. It was found more recently that the impurity phase (presumably VN), previously giving rise to additional X-ray diffraction lines and thus preventing definite indentification of the (111) superlattice line,' can be eliminated by preparing the alloy by arc melting in a helium atmosphere. The alloy specimen melted in this manner had clean surfaces and showed very littte, if any, nitride phase in the microstructure after annealing in vacuum at 1250°C and quenching. The relative intensity of the (100). superlattice line with CrK radiation was greatly increased and, in addition, a fairly strong (Ill) , superlattice line and even a detectable (210) , super- lattice line was obtained, when the powder produced by filing from the 1250°C annealed and quenched specimen was reannealed in vacuum at 625°C for 1 hr. By using a cellulose acetate film as a filter in front of the photographic film in order to absorb the soft radiation resulting from air fluorescence, the background intensity could be reduced considerably in relation to the intensity of the diffraction lines. All three superlattice lines, (100),, (111)., and (210)a, disappeared, as expected, when a radiation other than CrK, was used.1 For the powder reannealed at 625ºC, the strongest lines of the s pattern also appeared weakly, indicating that during an: nealing at 625°C a small amount of transformation took place from the body-centered-cubic to the u phase. However, since all superlattice lines to be expected in the 0 angle range used were actually very clearly present, it was evident that the high temperature body-centered-cubic phase had transformed into a CsCl-type ordered structure before much s phase could form. Reannealing filings for 1 hr at 700°C resulted in complete transformation into the u phase. After 1 hr at 650°C the transformation into IT was not quite complete, the strongest body-centered-cubic diffraction lines were still present, although fairly weak, and only the (100), super-lattice line was detectable (extremely weak). These findings not only confirm the previous conclusionsL as to the existence of a CsCl-type ordered structure in the Fe-V system, but they also indicate that this metastable ordered structure forms at about 600°C preceding the formation of the stable s phase, while at 1250°C the disordered body-centered-cubic phase is stable. The faint (loo) , super-lattice line previously observed in specimens quenched from 1200°C was probably due to the fact that the quenching of the powder in an evacuated fuse:! quartz capsule was not fast enough to prevent completely the ordering reaction on cooling. The present results conform with the suggestion that the A-B bond, in relation to the A-A and B-B bonds, increases in strength from CrFe to VFe to TiFc. It is, therefore, of interest to compare the measured values of the average atomic diameter for these three alloys with the corresponding average atomic diameters calculated from the atomic radii of the elements concerned. ASSUming A-B contacts

Jan 1, 1958

By M. Semchyshen, A. P. Coldren, W. G. Scholz

A survey of the Fe-Mo-B system was made to determine the extent to which boron might affect the microstructure and strength properties of iron-rich Fe-Mo alloys. Seventeen vacuum-induc tion melted ingots were prepared with approximate mo-lybednum contents 01 2, 4, 9, and 19 wt pct and approximate boron contents of 5, 14,50, and 630 ppm by weight. Phases extracted from annealed specimens and identified by X-ray diffraction analysis included E Fe3MO2, Mo2FeB2, and an oxide hazling a diffraction pattern practically identical to that of MnFez04. Three types of alloy strengthening were observed: a) Fe-2 pct Mo-B alloys were hardenable by a bainitic-type transformtion of austenite to ferrile; b) Fe-4 pct Mo-B alloys were hardened by the solid-solution mechanism; and C) Fe-9 pct Mo-B and Fe-19 pct Mo-B alloys were hardened by precipitation of the E Fe3Moz phase. Boron was observed to have a very strong hardening effect in the Fe-2 pct Mo alloys and a mild strengthening effect on the 1200°F properties of the Fe-4 pct Mo alloys. In the Fe-9 pct Mo alloys there was no consistent effect of boron on strength at either room temperature or 1200° F. The Fe-19 pct Mo alloys were so brittle that meaningful tensile or creep-rupture data could not he obtained. No dispersion hardening from borides was recognized in any of the alloys. THE high-temperature properties of iron-rich Fe-Mo alloys were studied by Reiter and Hibbard.' They found that the strength of the alloys increased markedly as the molybdenum content was raised from 0 to 15.9 pct by weight. The authors explained the various degrees of strengthening in terms of a) solid-solution strengthening, b) strengthening from a martensitic-type transformation, and C) precipitation strengthening. The objective of the present investigation was to conduct a survey of the iron-rich portion of the Fe-Mo-B system to determine whether the beneficial effects of molybdenum on the strength of iron can be enhanced by the presence of boron. It was thought that perhaps fine dispersions of molybdenum- rich borides would be found which could improve the high-temperature strength of ferritic alloys beyond the strengths attainable by molybdenum additions alone. Also, it was considered worthwhile to study the effects of boron in alloys which are essentially free of carbon. Most, if not all, of our present knowledge about boron in high-temperature alloys pertains to alloys containing carbon and carbides. EXPERIMENTAL PROCEDURES Alloy Preparation. Seventeen 8-lb ingots were prepared from electrolytic Plastiron, unalloyed molybdenum chips, and boron powder by a vacuum-induction melting procedure employing hydrogen as the main deoxidizer. The alloys were melted in alumina crucibles using 35-lb melts, with each melt being split four ways to achieve varying boron contents within four Fe-Mo base compositions. The results of chemical analyses conducted on chips machined from the chilled ends of the ingots are presented in Table I. The boron analyses were performed by a spectrographic method utilizing primary standards prepared from boric acid. They indicated that in ingots to which no boron was

Jan 1, 1964

By Arnulf Muan

PHASE relations in three isothermal sections (l000°, 1100°, 1200°C) of the system Ag-Fe-Pd have been determined as part of a program to develop improved crucible materials for containing low-melting iron silicates at low oxygen potentials. The following experimental method was used: Two- to 3- g samples of each of forty different alloys within the system Ag-Fe-Pd were made up from metals of 99.9 pct purity. The mixed metal powders were contained in a 1-cc crucible of dense recrystal-lized alumina and heated in a protective atmosphere (90 vol pct A, 10 vol pct H2), first to complete melting for approximately 30 min and subsequently at the desired equilibration temperature (1000°, 1100°, or 1200°C) for approximately 24 hr. The samples were then quenched rapidly to room temperature and examined metallographically as well as by X-ray techniques. Unit cell dimensions were compared with standards obtained by study of one-phase alloys of known compositions. The results are summarized in diagrams (a), (b), and (c) shown in Fig. 1. Heavy solid curves outline areas comprising compositions of mixtures consisting of the phases labeled for each area. Mixtures in which liquid is the only condensed phase present are confined to very narrow areas adjacent to the Ag-Pd join at high silver contents. An enlarged, distorted picture of the phase relations prevailing in these areas is shown in the upper-left circular insert. Particular attention is directed toward the misci-bility gap which occupies major parts of the composi-

Jan 1, 1962

By Chester A. Fulton

SUPPLYING as it does a necessity for healthy animal and vegetable phosphate production is a most important industry. We human beings also are animal as this war so surely proves. Unlike many other elements no substitnite is available for phosphorus or its compounds. Marvelous as are modern plastics none can lake the place of phosphorus in making hone structures. As meassured in these times the phosphate industry is not a large industry. Output of phosphate rock, the original source of our agricultural and ,chemical phophates amounts to only some twelve million long tons per annum in the entire world. Phosphates are compounds of phosphorus, which is always found in nature combined with other elements. It never occurs in nature as such. The first choice of the element phosphorus is tie itself strongly to oxygen and then to water moisture - thus becomeing phosphlic acid. This phosphoric acid in turn hunts around for a base such as lime for instance and together they make phosphate of lime.

Jan 1, 1944

By Arnold Hoffman

A RESPONSIBLE steel executive recently declared that scrap shortages, despite fantastic prices reaching up to $50 per ton, are responsible for the loss of 140,000 tons of steel a month and that in March 1947 alone 25 more steel furnaces could have been operating were it not for scrap scarcities. His answer to this serious situation was to ask for a speedier flow of scrap and also abolition of Government control over pig iron distribution. It would be more logical, perhaps, if an answer to this growing problem of scrap deficiency were sought within the steel industry itself. As long ago as 1933, L. B. Lindemuth, a consulting steel metallurgist, warned the steel industry that a shortage of scrap was inevitable and that beyond 1938, adequate supplies for open-hearth furnaces could not be expected. The outbreak of war, with consequent phenomenal demands on the industry, accelerated production of steel and further worsened the scrap situation. Today we are suffering from a condition which could have been prevented had the industry been more far-seeing and provided for an inevitable contingency. However, better late than never, and measures can now be taken to alleviate permanently scrap shortages in the future. This can be done by greater utilization of heavy sinter which experience proved is an excellent substitute for scrao and lump ore.

Jan 1, 1947

By R. W. Raymond

to same extent, the assumptions tinderlying Dr. Ilu?ley's con alusions. These amrrmptions are: that 'the loss of metal per million tons of trafffc, depends, first upon the circrtnistances under which the rail is worn; secondly, upon the proportions of its various constituents, ancl that the anlorlnt of loss is afEect~d by eacb constitnent in a cer tain ratio, so that if the circunlstances were the same for all tlie mils, the wear per nliilion tons might he upproxi91ately expre~sed by an equation of the form I + Cc + Pp + SR + Mm = R, io wtlioh I is an unknown valne, dependi~.rg on the quantity of iron (and other ingre dients not determined) in the rail, and assumed to be constant for all the rails ; c, p, s, and m are the experimentally determined quan tities of carhon, phosphorus, sulphur, and manganese, as tabulater1 in YIates VT and VII of Dr. Dudley's paper; and R is the experirnen tdlly dcterlnincd wear per million tons; while C, P, S, and M are onknown wfficients. In other words, it is assunled that the differ ence in wear is proportional to a difference in c, p, s, or m, and that the effects of a change in the amonnt of either are independent of the amount of the rest-—within the experinlental limit5 of the problem. It is also assr~med that sulphar, copper, and other ingredients, not determined, are qually present in all the rails, or at least {lo not affect the wear, since I is taken as constant. Dr. Dudley tacitly assumes the coefficient6 C, P, S, and M to be positive; and assigns certain valries to them, by means of which he redom t.he equation to the form I + Pa: = R, x being equal to cc + Es +Mm i Pp, or tjje uanjbe,. of so-called phosphorus units in the rail. But we do not have R directly given under constant circumstances. The varying weights (per engine, car, or train) and the varying epds, we must neglect for lack of data, and assume that in these rwpects the rails examined have been treated srlbstantially alike. But there remain the varying conditions as to track, which mnst he elirninsted. Dr. Dudley gives six clrlsses, four of which contain 8 rails each, and two 16 rails each. Beginning with the 6~st (tangent grade), take the mean of the figures expressing wear for that clam; and continaing tliis process through the other five, we obtain six expressions in quantity of loss 'by wear, which we assome tc, represent, in their differences, the varying conditions of the trarli, with respect to grade and direction. We now take the mean of these moans (giving double weight to the gmiip containing 16 ohwrvafieras). This general rnean is the 10 of metal per million tons of trafio for a rail of avorage constitution under mean ciroumstances.

Jan 1, 1881

By Juan Sodi, John F. Elliott

The standard free energy of ReS2 has been measured in the range of 1050° to 1250°K using H2/H2S mixtures and a slight variation of the method described by Hager and Elliott.1 The result is: The experimental method and apparatus were modified slightly for this study. Measurements on Cu2S were made to verify the application of the method to the work on ReS2. THE EXPERIMENTS AND RESULTS Briefly, the experimental method consisted of exposing a chip of copper or rhenium at a known temperature for 8 hr to a slowly flowing gas stream at the same temperature in which Ph2S and PH2 were known. The chip was withdrawn quickly from the hot furnace, and subsequently it was inspected for the presence of a sulfided surface. In the experiments described here, there was no ambiguity in any case as to the presence or the absence of the sulfide. At a given temperature, gas compositions for sulfidization were explored systematically until two compositions were found whose values of ?G°, Eqs. [I] and [2], were within approximately 100 cal of each other, one of which was sulfi-dizing and the other was not. These are termed the "straddle" compositions and it is assumed that the equilibrium composition lies between them. The chief modification to the apparatus, which is shown schematically in Fig. 1 of Ref. 1, was to support the metal specimen on a small alumina boat which could be moved along the reaction tube, 6 mm ID, by platinum wires. An appropriate seal at each end of the reaction tube permitted the sample to be moved from the cold end of the tube into the hot zone in 2 to 3 sec, and the sample could be withdrawn equally rapidly. Thus, it was possible essentially to quench the specimen from the reaction temperature with the reaction gas or helium flowing and without danger of breaking the reaction tube. The usual practice at the end of the experiment was to switch the gas system to the helium tank, flood the reaction chamber with helium, and pull the sample out of the hot zone. The purpose of the modification was to permit study of the sulfidization of copper without the complication of the back-reaction between the gas and the specimen as the latter cooled during slow withdrawal of it from the hot zone; this was a problem in the earlier work.&apos; A further improvement located the tip of the temperature-indieating thermocouple and the specimen precisely at the hottest part of the furnace. A carefully calibrated thermocouple, with its tip at the position of the specimen and with other conditions duplicating those of an actual experiment, showed that in the temperature range of 900° to 1122°C the temperature of the specimen differed from that of the tip of the indicating thermocouple by less than 0.5°C. The two positions were 0.5 cm apart. The reaction gas was prepared from ultrahigh-purity hydrogen (<l ppm O2, <0.5 ppm H2O) and CP grade hydrogen sulfide (99.5 pct H2S). High-purity helium (99.995 pct He) was used. All of these gases were purchased from the Matheson Co. All flow meters were recalibrated by the soap-bubble method with hydrogen, H2S, helium, and several gas compositions used during the study. These calibrations gave a linear relationship with a slope of 1.0 for the plot of log flow rate vs log pressure drop across the flow meter, in accordance with the Hagen-Poiseuille equation. The analysis of the gas was determined in the same manner as was reported previously. Good checks were obtained between the composition of the gas established by the flow-meter settings and by chemical analysis of the gas taken after the mixing bulb and ahead of the furnace. The pressures of H2S, H2, S2, and HS in the equilibrium gas at temperature were calculated from the following data :3 The pressures of the species S and S8 were negligible for the conditions of the experiments.3 There was no sign of vaporization of ReS2 either by weight loss or deposits in the reaction tube. Thus it is not possible to account for the apparent volatility of the compound reported by Juza and Biltz.2 The inlet gas composition and the calculated equilibrium ratio of PH2 S/PH2 for the "straddle" points of each experiment are shown in Table I. The specimens of metal for the experiment were small clippings of annealed copper (99.9+ pct) sheet 0.005 in. thick that was obtained from Baker and Adamson and of "high-purity" rhenium (99.9+ pct) sheet 0.005 in. thick that was purchased from Chase Brass and Copper Co. A specimen was removed from the apparatus; inspected for the presence of the sulfide, and then stored in a sealed vial. A fresh clipping was used in each measurement. The condition of the surface of each specimen after the experiment is noted in Table I.

Jan 1, 1969

By K. BRUCE DAVIDSON

-The North Central Texas area includes the following counties in Railroad Commission of Texas District 7-B: Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, S

Jan 1, 1946

By Paul E. Rosten

Introduction This papers describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Co. to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Co. operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously (Lindroos and Koski, 1966; Villar and Dawe, 1975; Koski, 1977). Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and fur¬nished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate¬kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to: (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1981

By William H. Spice

Drilling activities in South Central Texas for the year 1945 continued the steady increase over the past two years, while new fields discovered for the year included four new gas fields and one field extension. In the 30 counties included in this area, which comprises district No. 1, Oil and Gas Division, Railroad Commission of Texas, 141 exploratory wells were completed, compared with 61 drilled in 1944 and 29 drilled in 1943. Of these 141 tests, 55 were field well and 86 were wildcats; 38 were completed as oil wells, S as gas and gas-distillate producers, and 95 were abandoned as dry. Atascosa and McMullen Counties were the most active in the district, accounting for 73 of the wells drilled.

Jan 1, 1946

By V. A. Phillips, M. Safdar Ali

The tensile properties of Cu-0.20 pct Al, Cu-0.45 pct Mg, Cu-0.27 pct Cr, and Cu-0.22 pct Be solid-solution alloys were studied at -196°, 18°, 2509 and 500°C on wires internally oxidized at 900°and 1000°C. Internal oxidation produced marked increases in yield strength relative to pure copper, particularly at low temperature. The yield strength decreased with increase in temperature to a much greater extent than predicted by current theories of dispersion hardening. The strengthening effect of internal oxidation persisted throughout the entire stress-strain curve, but since a marked loss of ductility occurred at all test temperatures, only modest increases in tensile strength were realized. INTERNAL oxidation involves the preferential oxidation of a baser solute in a relatively noble solvent by diffusion of oxygen into the solid. Since the process is diffusion controlled, it is expedient to carry it out at a high temperature often approaching the melting point. The amount of solute is limited and the oxidation conditions adjusted so that oxygen diffuses inwards to meet the solute causing reaction to progress inwards and form subscale instead of only sur face scale. The reaction can be made to occur throughout the thickness of thin material producing a fine dispersion of oxide inside the metal. C. S. Smith1"3 appears to have been the first to recognize the true nature of the process of internal oxidation. Although extensive kinetic and metal-lographic studies followed by Rhines and coworkers,4-5 Chaston7 andMeijering and Druyvesteyn8 working independently were the first to report hardening effects due to internal oxidation. These results prompted detailed studies of the effects of internal oxidation on the hardness, tensile, creep, and fatigue properties of a number of alloys by G. C. Smith and coworkers9-12 in England, on hardness by Gottardi13 in Italy, and on hardness and tensile properties by wood14 in the U.S.A. Publications dealing with other aspects of internal oxidation will not be reviewed here. Internal oxidation of solutes having a high affinity for oxygen provides a means of obtaining very fine dispersions stable in a suitable atmosphere at temperatures well above those at which most age harden ing precipitates coalesce. The process therefore offers a method of producing thin sheet and wire of possibly outstanding creep resistance. The size limitation might be overcome by internally oxidizing porous powder compacts made from alloy powder before final sintering. PREPARATION OF ALLOYS The alloy ingots, which were approximately 5 1/2 in. long by 1 in. diam, were made up in a high-frequency furnace, using as raw materials OFHC copper, 99.99 + pct Al, high-purity magnesium, and master alloys of Cu-4.19 pct Be and Cu-10 pct Cr. The alloys containing aluminum and magnesium were melted ii closed high-purity graphite crucibles and solidified in the crucible which was lowered partly Out of the coil to give a hot-top effect. The alloys containing beryllium and chromium were made by melting in vacuo in alumina-lined sillimanite crucibles. The magnesium, chromium, and beryllium

Jan 1, 1960

By J. R. Cahoon, W. V. Youdelis

FOR the diffusion of copper in silver-rich alloys, there have been only two previous investigations, that of Seith and Peretti in 1936, and that of Sawatzky and Jaumot2 in 1957. Seith and Peretti obtained a value of 24.8 keal per g-atom for the activation energy of diffusion whereas Sawatzky and Jaumot obtained a value of 46.1 keal per g-atom. Admittedly, Seith and Peretti used relatively high concentrations of 2 at. pet Cu and polycrystalline diffusion couples, while Sawatzky and Jaumot investigated tracer diffusion in single crystals of silver. The difference in the results, however, seems too large to attribute solely to solute concentration, as a change of over 20 keal per g-atom in the activation energy suggests a change in the mechanism of diffusion. Therefore, in the present investigation the diffusion coefficient for copper in polycrystalline Ag-2 at, pet Cu alloy is re-established using conventional sandwich-type diffusion couples and electron-probe microanalyses, and the results are compared with those of the previous studies. The diffusion couples were prepared from high-purity silver (99.999 pet) and high-purity copper (99.999 pet). The silver disks, 1/4 in. long and 4 in. in diam, were machined from an ingot which had been solidified in a dynamic vacuum of 10-3 mm of Hg to eliminate oxygen absorption which otherwise would result in copper oxide precipitation in the weld zone. The alloy disks of similar dimensions were machined from an alloy ingot (nominal composition 2 at. pet Cu) which had been unidirectionally solidified to obtain a predictable solute concentration,3 and homogenized for 1 week at 800°C. Sandwich diffusion couples were made by pressure welding an alloy disk between two silver disks in an induction heating coil. The couples were diffusion-annealed at temperatures of 800°, 756°, 699°, and 630°C in tube furnaces in which the temperature was controlled to better than ± l°C. The diffusion couples were examined metallographically for weld defects, and couples showing even minute defects at the weld interfaces were rejected. Concentration penetration curves were established using an A.R.L. Microprobe analyzer. CuKO radiation was counted and converted to concentration using 0.5 and 1.0 wt pet Cu chemically analyzed standards. Initially, four continuous profiles were obtained, and averaged to obtain the final diffusion curve. The initial analysis was performed commercially and the welds were not located with respect to the profile. Therefore, the results were rechecked by the authors using the Mellon Institute A.R.L. probe. In the latter case, concentrations were obtained at 10-µ steps for four different traverses, and then averaged to obtain

Jan 1, 1968

By R. I. Jaffee, J. W. Roberts, D. N. Williams

DISPERSION hardening as an alloying process has aroused increasing interest in the past few years. This alloying procedure, in which an insoluble phase is dispersed randomly through a metal or alloy, is believed to be especially suited for the attainment of creep strength at elevated temperatures since the dispersed phase is metallurgically stable. Another advantage is that the physical properties of the matrix phase, such as electrical conductivity, remain relatively unaffected by alloying. These two characteristics resulted in interest in the applicability of dispersion hardening to copper and copper alloys. A study of copper alloys prepared by powder metallurgy methods has shown some strengthening from oxide dispersions.&apos; However, powder metallurgy processing would not be economical for large scale production of dispersion hardened copper-base alloys. Therefore, the research described in this article was initiated to examine methods of forming dispersion alloys which would not require powder metallurgy processing. If powder metallurgy processing is to be avoided, a method must be found by which the dispersion material can be introduced into and dispersed through the melt before casting. When the dispersed phase is an oxide or similar nonmetallic, it is extremely difficult to form a satisfactory liquid: solid dispersion since successful mixing requires that the melt wet the dispersed phase. It is almost impossible to force a nonwetted particle beneath the melt surface. This difficulty can be avoided, however, if the oxide particles are produced in molten copper by reaction within the melt. The problem would then reduce to maintaining randomness until solidification. Four procedures were considered for producing an oxide particle within molten copper by reaction. In all cases, the intent was to react oxygen (0) with a reactive metal (X) to form an oxide (XO) within the copper melt. These reactions were as follows: 1) (Cu-X), + (O)g (Cu)1 + (XO)S [1] 2) (Cu-X)1 + (Cu2O)s (Cu)x + (XO)S [2] 3) (Cu-OK)1 + (Cu-X)1 (Cu)1+(XO)9 [3] 4) (Cu-OK)1 +(X)s (Cu)1 +(XO)s [4] The reactions were carried out in an 8-lb melt of 99.98 pct Cu maintained in the vicinity of 2200oF by induction heating. Where possible the amount of the reactants was controlled to give 1 to 5 vol pct oxide. Mechanical stirring during the reaction period was used to minimize agglomeration of the reaction product. The presence of a reaction product was determined metallographically by study of an ingot cast from the melt at the end of the reaction period. Reaction [I] was studied by dissolving aluminum in the melt followed by forcing oxygen through the melt. The melts became quite sluggish during the reaction period suggesting that A12O3 was formed. However, the reaction product rose out of the melt rapidly, possibly due to the flushing action of the oxygen stream, and little dispersed phase was formed. Reaction [2] was examined by dissolving aluminum, silicon, or nickel i; the melt and then adding Cu20 (melting point 2250F). This procedure was unsuccessful. Although Cu2O was easily stirred into cop-

Jan 1, 1961

By Floyd C. Kelley

The literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke&apos;s iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be utilized to the fullest extent there must be a thorough invest,igation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibtiuni produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizingl which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure. Diffusion of Metals in Iron It seems to be a general law, whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, that a comparatively rapid, or abnormal, grain growth results. The grains

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By Frances Hurd, Clark

Iv 1897, Roberts-Austen(l)$ found an arrest in the thermal curves of alloys of 60 per cent. copper and 40 per cent. zinc. This break occurred from 450° to 470° C. Shepherd, (2) working in 1904, was unable to detect any change in the direction of the thermal curve. In 1911, Carpenter and Edwards(3) confirmed the work of Roberts-Austen and called this a eutectoid transformation of beta to alpha plus gamma. Hudson&apos;) in 1914, showed that the beta constituent could be produced synthetically at temperatures below the transformation point. He believed the change in the beta was polymorphic in nature rather than a eutectoid. The work of Matsuda(32) in 1922 demonstrated this break by thermal analysis, microscopic investigations, dilatation, electrical resistance measurements, and a thermoelectric study. He believed the transformation to be continuous from 300° to 480° C., and comparable to the A 2 transformation in iron. Later, in 1924, Andrew and Hay, with electrical resistance measurements, confirmed Matsuda&apos;s work. Imai(28) showed the transformation to be progressive and therefore a function of the temperature rather than the time. He stated that it was neither a eutectoid nor an allotropic change of phase. Atomistically expressed, it was a change, not of atomic configuration, but of atomic energy of some kind; and again it was compared to the A 2 transformation in iron. Imai believed that his analyses by X-rays led to the same conclusion. In order to study this change, at 470&apos;C., in homogeneous 60:40 brass, Homerberg and Williams «0> and Homerberg and Shaw(41) quenched their material in iced brine to obtain the beta solid solution and reheated at various temperatures. At 200° C., a change in the microstructure and physical properties occurred. A fine-grained structure, which they termed alpha and which had the appearance of a sorbitic steel, appeared, with an increase in the tensile strength to 82,750 lb. per sq. in., and a Brinell ball hardness of 240 with 3000 kg. load. At 470° C., the alpha

Jan 1, 1927

By J. C. Bierlein, R. A. Dodd

Endurance strengths at 10&apos; cycles, fatigue-hardening rates, and endurance strength/0.2 pct proof stress ratios have been determined jbr a range of Cu(Ni), Cu(Si), and S.R.0. Cu(Au) solid solutions. Some douht is cast on simple cross slip models of fatigue hardening in view of opposite composition dependencies of hardening displayed by Cu(Si) and Cu(Au). The temperature dependencies of hardening also are the opposite of predictions made on the basis of a cross slip model. A correlation apparently exists between the fatigue strength/0.2 Pc~ proof s1.re.s~ ratios and rates of fatigue hardening. An increase in PS/PS due to alloying or temperature change is accompanied by a decrease in hardening rate, and vice versa. In recent years there has been much interest in the determination of the dislocation structure of fatigued metals and alloys. The accumulated evidence, e.g., Refs. 1 to 5, suggests that the structure may be dependent on the stacking fault energy, 7, of the fatigued metal in the same way that fatigue hardening rates have also been shown to apparently depend on u .6&apos; 7 The above research followed the various earlier theories relating crack nucleation to ease of cross slip, e.g., Refs. 8 to 131 so "ggesting that y may indeed be the parameter of principal significance in all facets of the fatigue process. However, comparatively little attention has been paid to correlating engineering fatigue data with observations of the above type. Certainly, it would be useful if potential engineering fatigue performance could be assessed from a knowledge of easily determined alloy properties, and the present research originated from this standpoint. TO investigate the widest Possible range of 7 would require the use of two solvent bases, e.g., aluminum and copper, but a reasonable coverage can be provided by copper-based solutions alone. Therefore, it was decided to work with Cu(Ni) and Cu(Si) solid solutions, the approximate stackillg fault energies of which are given in Table I. The y range extends from low, Cu(7.5 at- Pet Si), to moderately high in Cu(2-5 at. ~ct ~i) and two of the Cu(Ni) alloys. The values listed in Table I should be regarded as qualitative only, being derived as follows. Dillamore and smallman14 quote a value of 85 i 30 erg.cm-2 for the stacking fault energy of pure copper, based on an earlier value due to Howie and swannl5 corrected by Brown&apos;s formula.&apos;&apos; Since the ratios (alloy)h(pure copper) have been reported17,18 for Cu(Ni) alloys containing up to 30 pct Ni, approximate ) values for these alloys can be computed, and a rough estimate of 7 for Cu(50 at. pct Ni) obtained by extrapolation. The relatively low y value obtained in this way for Cu(50 at. pct Ni) coincides with the observation of Nakajima19 that the stacking fault probability is a maximum at this composition. Likewise, the y values for the three ~u(~i) alloys are estimates based on values given by Swann and Nuttingo corrected on the basis Of Brown&apos;s estimate that the true 7 values are probably 2.3 times greater than those originally computed. In addition to the above alloys it was decided to investigate short-range ordered (s.R.O.) CU(AU) alloys containing up to 25 at. pct Au. This last alloy has been shown to have a well-defined planar arrangement of dislocations when deformed,21,22 probably due to cross slip being restricted by the S.R.O. Engineering fatigue data was to be represented by the determination of endurance strengths, and these were to be correlated with fatigue hardening and mechanical property data. EXPERIMENTAL I, order to study the desired properties and property changes, the following alloys were prepared: Cu(2.5 at. pct Si), Cu(5.0 at. pct Si), Cu(7.5 at. pct Si), Cu(5.0 at. pct Ni), Cu(25.0 at. pct Nil, Cu(50.0 at. pct Ni), Cu(5.0 at. pct AU), Cu(15.0 at. pct AU), Cu(25.0 at. pct AU). The copper and gold were zone-refined, while the silicon was semiconductor grade. The nickel was of 99.95 p,t. purity.* All alloys were induction-melted in a *Kindly supplied by the International Nickel co. helium atmosphere, appropriate precautions being taken to avoid segregation in the Cu-Au series. Rod stock was obtained by rolling and swag,ng. A few Bridgman single crystals were grown for fatigue-hardening studies, but most material was machined into polycrystalline fatigue speciments of the design shown in Fig. 1, and into polycrystalline tensile and fatigue-hardening specimens of simple cylindrical design. All specimens except Cu(Au) were annealed; the latter were quenched from above T, to produce short-range order. A few of the quenched alloys were examined for long-range order by step-scanning over

Jan 1, 1969

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.&apos;*&apos; Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory&apos; except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.&apos; It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------&apos;8&apos;77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.&apos;*&apos; Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory&apos; except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.&apos; It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------&apos;8&apos;77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953