Search Documents

By P. Breidt, E. S. Greiner

THIS note reports a determination of the melting point of germanium, and the liquidus of the Ge-Ga alloys; lattice constants of the a phase are given. The alloys were prepared by melting germanium (>20 ohm-cm resistivity) and gallium (99.6 pct) in evacuated silica tubes. The materials (50 to 70 g) were heated at 1000°C, held in the liquid state for about ¾ hr, and then cooled rapidly in the tubes. Points on the liquidus were obtained by thermal analysis which consisted of obtaining time-temperature data during heating and cooling the materials in high purity graphite crucibles and a helium at- mosphere. Temperatures were determined with a Pt—Pt-Rh thermocouple protected by a silica sheath. The couple was calibrated against a National Bureau of Standards calibrated couple and also against the freezing points of copper, silver, aluminum, and the 28.1 wt pct Cu, 71.9 wt pct Ag alloy eutectic. The samples for X-ray analysis were prepared by heating small pieces of the ingots in evacuated glass or quartz tubes at temperatures between 600" and 900°C for periods ranging from 2 hr to 22 days, periods deemed sufficient for equilibrium to be attained, followed by quenching in water. The heat-treated samples were ground to powder for X-ray analysis. The lattice constants of the germanium-rich phase (a) were determined with a baok-reflection focusing camera. The X-ray reflections (331 and 422 Cr Ka, 422 and 333 Cr KB) were corrected

Jan 1, 1956

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949

Carlisle: Jim Knapp, has been the good friend of hundreds-maybe thousands-of mining men in these western states in the last 40 or 50 years. Jim is going to talk about many of the mining camps of Nevada, where he has done plenty in the mining field during the last 50 years. Jim, for a starter, how did you happen to go to Nevada? Knapp: In the summer of 1902, two years after the discovery at Tonopah, the professor of mining at Stanford sent out myself and another student by the name of Joe Miller to make a report on the camp. We left San Francisco at 8 p.m., got to Reno the next morning, then took the train to Sodaville, arriving about 4:30 in the afternoon. The first man I met when I arrived at the Tonopah station was Tasker Oddie, a gentleman who later became the Govenor of the State and then a United States Senator. Before we got away from the stage station I also met S. H. Brady, the first mining engineer to put out his shingle in Tonopah. He afterwards became general manager of the West End Mining Co.

Jan 3, 1965

By F. W. Aul, R. C. Glenn

EXTRACTION techniques are of particular importance in determining size, shape an: crystal structure of particles smaller than l000Å in steels and other alloys. However, artifacts that can arise during the preparation of extraction replicas may lead to erroneous conclusions. The purpose of this note is to illustrate some of these artifacts and the misinformation that can result from their presence. An alloy of iron with 0.8 pct Cu was investigated in the following conditions: 1) Solution treated 3 days at 925°C in dry hydrogen and quenched in water. Aged in steps to precipitate copper, as follows: heated to 700°C, held 1 day; then furnace cooled to 50O°C, held 3 days; then furnace cooled to room temperature. 2) Solution treated 3 days at 925OC in dry hydrogen and furnace cooled to room temperature. 3) Solution treated 3 days at 925OC or 17 hr at 1100°C in dry hydrogen to dissolve all copper, then quenched in water. A normal parlodion dry-extraction technique was employed after etching the specimens with super picralP or with 2 pct nital. A wet-extraction method

Jan 1, 1962

C W. ROLFE, Professor of Geology, Emeritus, has of-fered a prize of $250 for the most valuable contribu-tion toward a new, better, or increased use of any mineral resource of the State of Illinois. The prize is open to anyone engaged in research, either privately, commercially, or in connection with any univer-sity or college staff, or any state or national bureau or sur-vey. The work must have been done, or at least completed, curing the year named. Three copies of the paper or books must be in the hands of the chairman of the committee on or before 6 p. m., May 1, 1928. If an unpublished paper is submitted, it should be typewritten, double spaced, on 8 1/2 by 11-in. paper. Unpublished results of study, or papers or books pub-lished since May 1, 1927, and before May 1, 1928, may be offered in the competition; but the results of the study must show real present or prospective economic value. Address all contributions and correspondence to Rolfe Prize Committee, 209 Transportation Building, University of Illinois, Urbana, Ill.

Jan 3, 1928

By J. S., Douglas

IN 1880, the late James Douglas, LL.D., was superintendent of the Chemical Copper Co., operating the Hunt & Douglas process for the treatment of the siliceous copper ores of the Jones mine at Phoenixville, Pa. In conjunction with this a refining furnace was operated. After correspondence with Ben Williams, of Bisbee Ariz., who was commencing the mining and smelting of the Copper Queen ore. Dr. Douglas decided-to make his first journey to Arizona. While making plans for the trip lie visited a friend in Philadelphia, a .Mr. Logan, a prominent lawyer. He, through Professor Treadwell, brother of the discoverer of the great Treadwell gold mine of Douglas Island, Alaska, had an option with his min¬ing partner, Mr. Lenig, on the Eureka and Wade Hampton claims near the headwaters of the Verde River in Yavapai County, Arizona. These two claims, later the source of practically all of the wealth of the Jerome district, were then owned by C. P. Head and Co. Prescott merchants. Hugo Richards, banker, and formerly sutler at Camp Apache; Rod and John McKinnon prospectors and Nova Scotians; and perhaps one or two 'other owners of minor interests. Mr. Logan, hearing of Dr. Douglas intended trip to Bisbee, asked him to go first to see the two mining prospects, and this, Douglas, in need of the $500 fee, agreed to do as the time on the option on the claims was running short.

Jan 1, 1935

By F. Valton

In the number of the Engineering and Mining Journal for April 7th, 1877, Mr. W. P. Ward, of Cartersville, Georgia, explains in a very interesting manner, the results he obtained in the manufacture of ferromanganese in the blast furnace. These results may be summed up as follows : Production in the blast furnace of an alloy containing 67.2 per cent. manganese and 3 per cent. of carbon at most, with a utilization of the manganese amounting to 58 per cent. With the exception of the indicated proportion of' carbon, which should be almost doubled to express the true state of facts, we would have had no observations to make on Mr. Ward's paper had he taken into account the results obtained in the same line in other centres of production. Before 1870, spiegel with 8 or 10 per cent. manganese only was known among blast-furnace products. In a journey to Sweden, in 1871,I ascertained that the Schysshyttan works manufactured regolarly a spiegel with 18 per cent. manganese. Later, at the Vienna Exhibition, in 1873, the Sava and Jauerburg works, in Carniola, presented to the jury a ferromanganese, obtained in the blast fur-

Jan 1, 1879

By Theodore B. Counselman

Of all natural resources, iron ore made into steel is the most important both in tonnage and value. The primary reason for the prosperity of the United States in the last century has been its pre-eminence in domestic supplies of iron ore and steel. The depletion of these reserves by two world wars and by the demand for richer blast furnace charges, as well as the constantly growing world- wide demand for steel, has fostered the recent quest for new iron ore mines around the globe. These developments have made a dramatic change in the iron ore picture of the world. It is the purpose here, however, to look briefly at the development of the United States iron ore industry, which has played such an important role in the events leading to the modern day boom in iron ore exploration.

Jan 7, 1965

By Jack A. Crichton, Henry J. Gruy

This paper discusses methods used in the estimation of natural gas reserves and the general conditions under which the various methods are applicable. The factors used in estimating natural gas reserves are reviewed. Errors which have been found to occur frequently are listed. Introduction The estimation of natural gas reserves has become of paramount interest because of the increasing importance of gas in the nation's economy. Gas is a most desirable fuel, a fact substantiated by the continued rise in the market demand. In addition, new uses for gas are being developed by the chemical, plastic, and associated industries, and plants are being built to make gasoline from natural gas. These are a few of the factors contributing to the importance of the nation's natural gas reserves. With the increased importance of gas there is an increase in the need for reliable estimates of the magnitude and availability of natural gas reserves. These estimates are being used currently: (I) to determine which fields contain sufficient available reserves to justify the construction of pipe-line outlets to serve particular markets; (2) to design pipe lines necessary to serve those fields adequately;] (3) to determine the location of industrial and chemical plants; (4) to finance the development of gas properties, and the construction of gas pipe lines; (5) to determine fair and adequate depletion allowances and depreciation rates; (6) to justify applications for gas pipe lines before various regulatory bodies; (7) to determine the number of wells required to exploit the reserves most economically; (8) to aid in establishing values for the purchase or sale of gas properties, and for purposes of inheritance taxes; (9) to determine equities under unitized operations; (10) to provide a basis for calculating the economics of gas-cycling operations. History or Estimation of Natural Gas Reserves The natural gas industry in the United States had its beginning during 1826 when natural gas was used for lighting the city of Fredonia, N. Y. The first natural gas pipe line was a 25-mi]le wooden line constructed from hollowed logs, connecting West Bloomfield and Rochester, N. Y. There is no record of an attempt to estimate the gas reserve at West Bloomfield but an attempt was made to determine the capacity of the well by measuring the time required to 611 a large balloon. One of the earlier publications concerning estimation of natural gas reserves is the "Manual for the Oil and Gas Industry," published by the Treasury Department, United States Internal Revenue, in i9i9. The following methods of computing "gas depletion" are listed: (I) production decline of the gas well or property; (2) decline in open-flow capacity; (3) comparison with the life history of similar wells or properties, particularly those exhausted Art

Jan 1, 1949

The mountains of Utah contain one of the largest deposits of high grade bituminous coal in the world. According to the United States Geological Survey, there are 13,130 square miles of land known to contain workable coal, and these extensive fields contain 196,000,000,000 tons of coal. More remarkable than the extent of the coal fields is the thickness of the coal beds. Over three-fourths of the output of coal in Utah is recovered from beds ranging from 8 to 17 feet in thickness, as com- pared to one-eighth of the output of the entire country from such beds. In 1917, Utah mined one-third of its coal from seams at least 16 feet thick, compared to one-half of one per cent of the total bituminous output of the country from like seams. Coal at Wales, in Sanpete county, and in the vicinity of Coalville, Utah, was, it is reported, the first discovered by white men in the state. Wales claims the distinction of having produced the first coal mined in Utah. Two men, who had been coal miners in Wales, learned of the coal from an old Indian chief who called it "rock that would burn." In 1857, the town of Wales was founded and coal mined, and in 1858 some coke was manufactured and hauled by ox team to Salt Lake City. South of Wales is Castle Valley, in Wasatch Plateau field. From 50 to 60 miles of the old Spanish Trail from Santa Fe. New Mexico, to Monterey, California, lies in Castle Valley. The coal in this field may or may not have been known at the time the trail was used extensively. The first published reference to this coal, however, was made by a party of the Corps of Topographic Engineers in their journal for October 11, 1853.

Jan 1, 1925

By A. U. Seybol

Eight binary iron alloys were examined after ion nitriding experiments to determine the behavior of the following elements: Al, Mo, Mn, Si, Ti, V,Cr, and C. Only Al, Cr, Ti, and V additions caused hardening in binary iron alloys. A few steels were examined to see the effect of Cr, Cr + Al, Cr + Ti, and Cr + V. It is suggested that a useful new class of ni-triding grade steels might be those containing about I pct V. The nitriding of steel, first described by Fry1 about 45 years ago, rapidly attained commercial application with very little knowledge of the fundamentals involved. While Fry,' in describing the status of nitriding in 1932, apparently correctly postulated hardening by precipitated nitrides, the details of the nitriding process were not understood, nor has the situation changed much since that time. It is also interesting to note that the compositions of some typical nitriding steels given by Fry at that time have changed little in the intervening years. Currently used nitriding steels owe their surface hardening to either chromium (as in 4340 steel) or aluminum plus chromium as in the Nitralloy grades, where both CrN and AlN appear to contribute to harden ing. Titanium additions have been studied experimentally, but thus far titanium steels have not won wide commercial acceptance. This subject will be expanded later. The orthodox ammonia nitriding process has been reviewed very adequately many times as in Jenkins3 and Case and VanHorn,4 and their is no need to outline the process here. Ion nitriding is not as well-known, although there have been several descriptions5-9 of the process given, sometimes with comparisons with the ammonia process. Most of these papers are primarily concerned with a description of the equipment, or of the physics or electrical engineering aspects of ion nitriding, but Noren and Kindbom9 gave the results of a metallurgical investigation using both processes. In brief, ion nitriding is carried out in a vacuum chamber from which the air is exhausted and replaced by a N2-H2 mixture, typically containing 10 to 20 pct N2, at about 5 to 10 torr pressure. While ammonia gas has also been used in ion nitriding, there is no evidence that ammonia makes any improvement in the ion nitriding process. A few hundred volts dc is applied between the grounded container wall (positive) and an insulated center post supporting the work (negative) to be nitrided. A glow discharge is created in the ionized gas, accelerating positive nitrogen ions to the work. These ions contain enough energy to form the normally unstable Fe4N "white layer", thus establish- ing surface nitrogen solubility characteristic of the a Fe/Fe4N equilibrium. This creates a substantial concentration gradient, driving dissolved nitrogen into the steel. The temperature employed is in the same range (around 500" to 550°C) as in ammonia nitriding, but because of factors which are not understood at present the nitriding time is ordinarily considerably reduced in ion nitriding. Other advantages have been cited,9 but it is not the purpose of the present work to contrast the two processes. The present objective was to examine the behavior of binary iron alloys during ion nitriding with respect to the microstructure, hardness level, and depth, and to examine some of these factors in steels as well. In this way it was hoped to be able to find out something about the individual role of these elements in steels. While all the work was done by ion nitriding, there seems to be no reason why any conclusions reached would not equally apply to ammonia nitriding, excepting only the kinetic aspects of the process. Another objective was an exploration of the critical-ity of the ion nitriding variables: gas composition, pressure, temperature, and time. EQUIPMENT AND MATERIALS The equipment used was substantially as described by Jones and Martin.8 The vacuum tank was about 12 in. in diam by about 18 in. high, and consisted of water-cooled stainless steel, with a single small window at the top for viewing inside. This sat on a heavy mild steel base equipped with the main pumping port, pressure control port, and vacuum gaging. A series of variable resistances was interposed between the glow discharge and a large-capacity -40 amp variable primary transformer feeding a 1000-v transformer, but 600 v were about the maximum ordinarily used. With the small l-in.-round, 4-in.-thick discs used for nitriding, the electrical load was usually about 500 v at 0.8 amp. The specimen temperature was controlled by a stainless-steel sheathed chromel-alumel couple, whose junction was in the steel stool upon which the flat discs were placed. These were ground through 400 Sic paper. Cycling of the temperature controller caused -0.2 amp variation in ion current, providing an ample control band. The binary iron alloys were made from vacuum-melted hydrogen-deoxidized electrolytic iron and alloys of 99.9 pct purity. Cast ll-lb-square tapered ingots were forged and hot-rolled to about 11/4-in.-diam rounds. Discs of 1/4 in. thickness by about 1 in. diam were machined from the rods for nitriding specimens. The following alloys were prepared: 1 pct each of Mn, Mo, Cr, Ti, Al, V, Si, and an Fe-0.8 pct C alloy. EXPERIMENTAL VARIABLES Of the variables total gas pressure, nitrogen partial pressure, temperature, and time, only nitrogen partial pressure was found to be critical to the operation. A critical nitrogen partial pressure was found corre-

Jan 1, 1970

The Institute maintains a dual relationship with students: (1) an individual relationship with a Student Associate; and (2) a relationship with local organizations of students, known as Affiliated Student Societies or Student Chapters. 1. The conditions of Student Associateship are set forth in Section 8, .Article 1 of the By-laws of the Institute (see p. 45 and following pages) During 1934, sundry amendments were made for the purpose of improving the student relationship. Post-graduate students are now eligible; and the associateship can be maintained, with the payment of the regular dues of $2 per gear, for 18 months following graduation in June. A Student Associate is given a subscription to MINING A ND METALLURGY: he is accorded the privilege of getting special publications such as "The Porphyry Coppers" and "Ore Deposits of the Western States" at the reduced prices applicable to Members; he has the privileges of the Engineering Societies Employment Service and the Engineering Societies Library; and he is not only invited but urged to attend all meetings of the Institute, its Divisions and its Local Sections. The Institute wants to extend the hand of professional fellowship to students following mineral industries curricula.

Jan 1, 1936

By W. P. Lass

(San Francisco Meeting, October, 1911.) TEE purpose of this article is not only to describe the plant and method of cyaniding the Treadwell concentrates, but to present some of the results of the experimental work obtained in the past three years for the Alaska-Treadwell Gold Mining Co., at Douglas Island, Alaska., under the direction of F. W. Bradley, Consulting Engineer, and Robert A. Kinzie, General Superintendent, of the affiliated companies. At the time the experimental work was undertaken the concentrates were being shipped to the smeltery at Tacoma, Wash., and the cost for treatment of 3-oz. (gold) concentrates was $11.95 per ton, divided as follows: Smelting-charges, . $4.00 Loading, freight, insurance, etc., 2.89 Interest due to time lost in transit and in settlement, . 0.05 Loss due to settlement for 95 per cent. of the gold at $20 per ounce, 5.01 Total, . . $11.95 From the experimental work described later, it was estimated that 96 per cent. extraction could be made by treatment on the ground, and that the cost, when treating 80 tons per day, would be $3.25 per ton, divided as follows; Per Day. Per Ton. Labor, . $66.16 $0.827 Chemicals, . 76.60 0.960 Power and steam-heat, 67.60 0.845 Marketing-, refining- and other charges, 49.36 0.617 Totals, . . $259.72 $3.250 Adding to this total the 4 per cent treatment-loss, which on 3-oz. concentrates amounts to $2.48, gives a total cost of $5.73 per ton. Comparing this with $11.95, the cost when shipping to the smelter, leaves a net gain of $6.22 per ton by the local

Feb 1, 1912

By R. Kossowsky

Structural changes in Be-Cu, Be-Ni. Be - Ag, and Be-Fc alloys pressurized in a solid medium were invesligated by resistivity measurements , X-ray diffrac lion in situ and metallogvaphic examination. Some limited tests in liquid medium were also conducted. Good correlation was oblained between diauges of slope of relative resistance us pressure and changes in diffraction pattern. Metallographic examination rez:ealed that the copper, silver, and nickel alloys lwiu heauily due to the applicalion of pressure at room temperature. Using polarized light technique {1012}, {1011}, and possible {1010} twinning planes were identified. At eleuated temperature twinning was moslly confined to the {1012} planes. Although twin-ning could be promoted by application of hydroslutic pvessure (liquid medium), it was strongly enhanced by the pvesence of a nonhydvostatic shear component due to pressurizalion in a solid medium. It was further obserced that a decrease in grain size inlnibiled twinnitzg activily. A great deal of effort has been expended in recent years to render beryllium useful for structural applications. Efforts were concentrated towards a possible phase change and to promoting other than basal deformation modes. Quenching experiments to obtain the high-temperature bcc phase have failed,' nor were alloying additions successful in improving ductility of the brittle hcp phase.2 Herman et a1.3 have reported a new {1011} twinning mode in a Be-4.4 wt pct Cu alloy oriented for a C axis compression sustaining loads to 440,000 psi. A new approach using high-pressure techniques was undertaken at Curtiss-Wright, Wright Aeronautical Division Laboratories. Marder4 reported a 25 pct decrease in relative resistance of commercially pure beryllium at 92 kbar. He proposed that this discontinuity corresponded to the bcc phase found at high temperature; however, X-ray diffraction in silu did not confirm a phase transition.5 contre6 has recently shown that the bcc transition in pure beryllium is lowered to 800°C at 80 kbar accompanied by a 50 pct increase in relative resistance. The purpose of this paper is to report on one phase of an investigation of the effects of high pressures and temperatures in beryllium alloys, namely, twinning behavior in Be-Ni, Be-Cu, Be-Fe, and Be-Ag alloys pressurized to nearly 100 kbar and temperatures up to 200°C. EXPERIMENTAL METHODS Material was obtained from Nuclear Metals, Inc., in the form of a 1.5-mm-diam wire extruded in stainless-steel cladding at 1600° F. Nominal composition of the alloys is listed in Table I, and the major impurities are are given in Table 11. Pressures to 100 kbar* were ob- tained using a National Bureau of Standards type 100/400 ton tetrahedral unit supplied by Barogenics, Inc. This type of apparatus contains a retaining sleeve with a conically tapered internal surface and four pressure-intensifying anvil assemblies with tungsten carbide tips. The 10-mm-long specimen fits into a pyro-

Jan 1, 1968

By Kim Beattie

IN spite of the fact that in 1944 Canada experienced a decline in production of all her leading base metals-nickel, zinc, lead, and copper; despite uncured headaches in the coal-mining industry; and cheerfully ignoring a still further drop in gold, the most valuable product of her mines, which had the lowest output of any year since 1931, the Canadian miner retains the traditional optimism of miners everywhere as he looks forward to the postwar period. Some factors should keep the Canadian mining industry from being too optimistic of the coming era of peace, but the fraternity generally holds that its confident attitude towards the future is based on sound reasons. The decline in production in the Canadian mining industry last year can be almost wholly attributed to the serious shortage of labor and the difficulty in obtaining transport and supplies in remote areas. Some falling off occurred in the demand for certain strategic metals, but the diversion of gold miners, especially, without replacements being obtainable, to direct war work or allied pursuits, was certainly the principal cause of the reduced output in 1944. But that is a situation which will right itself at the close of the conflict.

Jan 1, 1945

By Shun-ichi Satoh

In the previous paper, the writer indicated that the arc welding of cast iron is practicable only when barium carbonate is used to retard the fusion of electrodes. Later, he tested the effects of 48 other elements, to discover the cause of their retarding action. Wrought-iron bars 33 cm. long and 0.53 cm. dia. were used as electrodes. The chemical analysis of the original electrode is given in Table 1. Table 1.—Analysis of Electrode Per Cent. Carbon.................................................. 0.045 Silicon................................................... 0.028 Manganese....................................... Trace Phosphorus.............................................. 0.047 Sulfur................................................... 0.008 Each of the bars was wound with a twine of asbestos (1 mm. dia., weighing 0.5 g.) and then was coated with a mixture of equal quantities of graphite and carborundum and one of the compounds listed in the second column of Table 2. The method used in coating was as follows: The mixtures were reduced to paste by adding to them a solution of water glass (1:3); they were next put in a glass tube of 8 mm. inner diameter, with funnel-shaped mouth (the same tube shown in the previous paper); then the bars were passed through the tube so that the mixtures were coated on them. The glass tube was used only as a means of making the diameters of all coated bars exactly 8 millimeters. The cast iron was deposited on the steel plates by connecting the electrodes first to the positive and then to the negative pole of the generator. The figures representing the time, voltage, amperes and energy required to melt each electrode are given in Table 2. They are arranged in the order of the atomic weights of the elements contained in the coatings. In Figs. 1 to 4, which show respectively the time, current, voltage and energy required in this operation, the abscissas indicate the atomic weights of the elements contained in the coatings, and the ordinates

Jan 1, 1929

By R. H. Hiltz

Three titanium alloys, known to provide a mechanically unstable p structure after quenching, were selected as material for a study of the Origin and nature of stress-induced transformation. Data from hardness and tensile tests were used to study the initiation of marten site and the effect of the transfornation and transformation products on the mechanical properties of B titanium, particularly the stress-strain relationships. With the exception that the materials investigated showed a natural aging reaction in the P condition, their behavior is analogous to that of' stress-transforming stainless steels. The transformation starts after initial yielding and is essentially complete just prior to .maximum loading. Once initiated, the martensite itself is capable of propagating the transformation. The deforn-ing materials show low strength, high ductility, and a high strain-hardening exponent. In metallic systems which undergo a diffusionless transformation on cooling, it is possible to produce a similar transformatiorl by plastic deformation under special conditions. Dewez' in delineating Ms temperatures for the titanium-rich end of most titanium binary systems:, established the point of intersection of Ms with room temperature for those particular alloys. Alloy compositions which would quench to mechanically unstable p were established from these data. The first investigation into the possibility of stress-induced transformation occurring in titanium met with little success. It was concluded that such a transformation in titanium was possible only under very special conditions. Continued effort in this direction, however, showed certain Ti-Mo binaries to be highly susceptible to this phenomenon. This fact was utilized by Liu to study the habit planes of martensite and by Machlin and wenig5 to study the effects of stress and plastic deformation on the P to a prime transformation in titanium alloys. The first investigation of the mechanical properties of these alloys was conducted by Holden and his coworkers at Battelle Memorial Institute.' The potentiality of the alloys i3s sheet-forming material was recognized, and the data reappeared in a survey of this type of titanium material.? The initial optimism was tempered by the difficulties in obtaining homogeneous 2i-Mo alloys in commercial-size ingots. The increasing need for good sheet-forming material kept investigation in this direction active, resulting in the development of a commercial alloy of this type.' This study was undertaken to obtain a clearer picture of the mechanism of stress-induced transformation in titanium. MATERIALS AND TEST PROCEDURE Three alloys were selected for this investigation: one a Ti-Mo alloy; another a Ti-Cr-Mo alloy, known to deform martensitically; and the third, a Ti-V alloy with an Ms below room temperature and an Md above room temperature, but known to contain w phase in the quenched condition. The compositions of these alloys are given in Table I. These alloys were cast as 5-lb experimental ingots, employing skull melting. The ingots were hot-forged into 1-in.-round bars. Two 72-in.-thick slices were cut from each bar for hardness testing; the remainder was cut into 0.252-in. tensile blanks. The tensile blanks and one hardness disc from each bar were heated in salt to a temperature 100°F above the 0 transus, held 2/2 hr, and brine quenched. X-ray analysis showed the pieces to be 100 pct 8.* *Omega cannot be distinguished from p by the technique employed. Tensile blanks were machined to size after this treatment. TO prevent transformation due to machining stresses, the shoulders and gage length were ground. True stress-true strain curves were

Jan 1, 1960

By E. C. W. Perryman

On electropolishing, high-purity Cu-Sn and Cu-Sn-P alloys with more than 5 to 9 pct Sn were found to contain many grain boundaries with a ridge-and-furrow profile. The effect was not eliminated by solution treatment and was present at the new boundaries in recrystallized material. It could be produced by diffusing tin into the 3 pct Sn alloy and it is concluded that the effect is due to enrichment of certain boundaries in tin, or possibly in an impurity present in the tin, in solid solution. IN the hot working of tin bronzes, especially those with moderately high tin contents, considerable difficulty is frequently encountered from intercrystal-line weakness, which results in cracking at the edges in sheet on strip rolling and in the unsupported regions of the rod in rod rolling.' These difficulties are not at all pronounced with up to 3 pct Sn, but at 5 pct Sn impose serious limitations and at higher tin contents, especially if the phosphorus content is also high, they may become very severe. In some work carried out at the laboratories of The British Non-Ferrous Metals Research Association it was found that a notable lack of ductility in tension at elevated temperatures, associated with intercrystal-line failure, was characteristic of tin bronzes even of relatively high purity. That the intercrystalline fracture is not due to a brittle or molten impurity phase at the grain boundaries was shown by the fact that the temperature at which intercrystalline fracture first occurred decreased with decrease of rate of straining. Tensile tests on some commercial tin bronzes, reported by Goetzel,² show a similar fall in ductility with increasing temperature. As no visual evidence had been obtained showing that the grain boundaries of the tin bronzes were different from those in copper, a more detailed microscopical examination was carried out, and the results of this are given in the present report. Several workers"' have observed that electrolytic polishing is a powerful tool for detecting small amounts of a second phase and in particular for detecting high solute concentrations, "equilibrium segregation," at grain boundaries. Since it had been found that the suggested solutions for electropolishing bronze and the standard solutions for brass and copper did not give satisfactory results it was first necessary to find a suitable electropolishing solution.' Experimental Procedure Materials Used: The cast and wrought materials used for this work were the same as those used for the mechanical tests referred to above. They comprised 3, 6, and 9 pct Sn alloys without phosphorus and the same three basic alloys with 0.03 and 0.4 pct P. A 5 pct Sn alloy without phosphorus, of similar purity, was also examined. The basis materials were Chempur tin, high purity 15 pct phosphor-copper and cathode copper, and spectrographic analyses are given in Table I. Treatment: The cathode copper was first melted under charcoal, degassed by plunging marble chips beneath the surface, and cast through a coal gas flame into sand molds to produce a number of small ingots which after machining were of a suitable size for subsequent vacuum melting. Chill cast bars of the alloys, approximately 1¼ in. in diameter, were then made by melting and casting in vacuo, the tern-

Jan 1, 1954

By W. A. Oates, J. A. Lambert, P. T. GaIIagher

Monte Carlo methods have been used to compute the arrangements of interstitial atoms dissolved in tetrahedral sites in bcc lattices. It is assumed that the presence of an interstitial atom "blocks " a certain number of neighboring sites and prevents their occupancy. Sites "blocked" by more than one filled site are allowed for. The computed values of. the mean occupation number (defined as the ratio of the total number of sites blocked to the number of solute atoms are used to calculate the configurational entropies of the solutions. These entropies are compared with those resulting from previous theoretical studies of this problem and also with available experin~ental data for the p Zr-H, Nb-H, V-H, and Ta-H systems. Evidence is also given that the "blocking" explanation of low limiting compositions in these systems, rather than this being due to initial limitations on the number of sites available, is probably correct. THE ideal partial configurational entropy of mixing of an interstitial solute in a metal is given by: where p is the number of interstitial sites per metal atom and Xi is the atomic fraction of the interstitial. For the bcc lattice. which we shall be concerned with in this paper, the interstitial positions are shown in Fig. 1. It can be seen that for the tetrahedral sites, p=6. whereas for the octahedral sites, p = 3. Different emphasis has been placed on the relative importance of energy and entropy effects in determining deviations from ideality in interstitial solid solutions. In some cases the same system, e.g., Fe-C, has been described by the contradictory regular and athermal solution models indicating that the enthalpy and entropy functions, derived from equilibrium data, are frequently not accu.rate enough to differentiate between these treatments. However, for certain metal-hydrogen solutions the equilibrium data is available over sufficiently wide ranges of temperature and composition to permit a reasonably accurate determination of the compositional variation of the heats and entropies. Hoch&apos; has attempted to interpret the results of interstitial solid solutions in terms of a regular solution model. In the case of the Ta-H system where 13 = 6, this model entails fitting the experimental relative partial entropies of solution, asH, to the equation: where ASgs is the relative partial excess entropy of solution of hydrogen. Hoch found that the results of Mallett and Koeh1 could be fitted to this equation with an approximately constant value of AF up to XH = 0.25. However, it is apparent from the solubility isotherms in this system which become asymptotic to the composition TaH that, since (Xh /6 - ~Xh ) becomes infinite only at TaH6, it is necessary that AS<&apos; tends to infinity at TaH. In other words, the low saturation composition of TaH, instead of the anticipated TaH,, eliminates the possibility of applying regular solution theory to such systems. Rather large negative excess configurational entropies must exist at higher hydrogen concentrations in order to explain the lower saturation values. To account for these low limiting compositions and excess entropies two distinctly different approaches have been followed. Rees and many others1-l2 have assumed that not all interstitial sites are crystallographically equivalent with respect to the interstitial addition; that is, in Eq. [I] p is less than the value anticipated from geometrical considerations. To describe, say, a bcc metal-hydrogen system with a limiting composition of MH by this approach one would consider that p = 1 in the first instance instead of p = 6.&apos;j3 In some cases, nonintegral values of B have been taken in order to improve the fit with the experimental data over limited ranges of composition. The other approach which has been used to explain the low saturation compositions is to assume that, although all sites are available for occupancy, strong repulsive interactions exist between the neighboring interstitial atoms, and hence occupancy of any site excludes or blocks a certain number of neighboring sites from being occupied. Earliest treatments of this concept considered the exclusion of an integral number, of nearest-neighbor sites from being occupied at all concentrations. In this case, the partial configurational entropy is given by: These early treatments failed to allow for the overlap of the blocked sites which will arise at all but the very lowest concentrations. More recently attempts have been made to calculate the effect of this decrease in the number of blocked sites on the configurational entropy. Using the quasichemical treatment of interstitial solid solutions as given by Lacher and assuming that an infinite repulsive interaction energy existed between the solute atoms. atom obtained an approximate configurational entropy applicable to the blocking with overlap case:

Jan 1, 1970

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix. Few of the operating companies in the Florida phosphate district have applied isopachous (Greek isos, equal and pachys, thick) to mapping. The writer believes there is a need for the techniques discussed herein and that they can be applied to mapping other geologically similar areas in either economic or scientific investigations. The land-pebble phosphate district of Florida occupies a compact area in the west-central part of the state. It includes mainly the following land survey divisions: Ts. 27 S. through 32 S. and Rs. 20 E. through 26 E. The town of Mulberry, Fla., is in the approximate center of the district. The strata of the area, which is part of the Gulf Coastal Plain, occur in thin formations with broad outcrop belts, and low dips. The topography is subdued and gently rolling with three marine terraces, which are found at 30, 100, and 150 ft above sea level,&apos; accounting for most of the relief. Occasional small sinkhole lakes are present, most of them above the 150-ft shoreline. The phosphate deposits occur in unconsolidated sediments such as clays, sands, and sandy clays. They are overlain by a heterogeneous assemblage of sands, clays, muck, and iron-cemented sand, easily penetrated, in most cases, by a hand auger or drill. Limestone, locally called bedrock, or a calcareous bedclay, thought to be a residue of the limestone, directly underlies the phosphate deposits. General Requirements Most companies and independent prospectors operating in the district have furnished prospecting data to the U. S. Geological Survey. The information is recorded on either field logs or prospecting maps and includes the following information for each hole drilled: location of the hole, thickness of the overburden, thickness of the matrix, phosphate content in long tons per acre, grade of the phosphate content expressed as the percentage of bone phosphate of lime (P2O5 x 2.18) or BPL, and the per- centages of iron-aluminum oxides and insolubles. The phosphate is classified according to size as either pebble or flotation material. The milling processes of the companies vary, and the size classification is necessarily different in many cases. However, pebble may be considered as larger than 14 mesh and flotation material as smaller than 14, but larger than 150 mesh. Some prospecting data include the exact depth at which bedrock or bedclay was reached, and these figures greatly increase the reliability of the data both for isopachous mapping and for mapping the basement. A drilling density of four holes per 40 acres of land furnishes a minimum amount of data for isopachous and related mapping. From the minimum of four, densities up to 32 holes per 40 acres are used. The various drilling densities may influence the choice of the proper scale. Selection of the proper scale is dependent upon the known drilling densities, the subsurface variations to be shown, the extent of the area to be mapped, and the detail desired in the completed map. Scales of 1:24,000, 1:4800, and 1:2400 are used in isopachous and related mapping by the Florida Phosphate Project. The 1:24,000 scale is used most effectively with drilling densities not exceeding eight holes per 40 acres. The subsurface variations should be relatively low and uniform, permitting the use of smaller intervals without undue crowding of the lines. Comparatively large areas can be mapped on this scale, but minute detail is necessarily sacrificed, because the information is drawn from a maximum drilling density of only eight holes per 40 acres. Isopachous and related maps of the 1:4800 scale are made of areas on which the drilling information covers from 4 to 16 holes per 40 acres. Moderate subsurface variations with relatively sharp gradations can be shown accurately. The area represented by the maps is reduced considerably in favor of detail. The 1:2400 scale is most frequently used by the Florida Phosphate Project. It lends itself particularly well to isopachous and related mapping, being easily adapted to the multiform drilling data available. Maps of this scale are prepared with information ranging from 4 to 32 holes per 40 acres; however, use of the minimum drilling density on the

Jan 1, 1952