Search Documents

By M. M. Neale

The pottery department has been aptly described as the "heart of the zinc plant," md every operator of a horizontal-retort plant is acquainted with the fact that good retort practice is the keystone of the smelting process. Since retorts and condensers are clay products, it is obvious that improvements in other branches of the ceramic industry should be observed for possible adoption in the pottery process for zinc smelting. Deaeration of clay bodies is one of the improvements that have become fully, established in many brick and pottery plants. Our investigation of a number of these installations always yielded the same answer—improved practice. Improvement in workability, elimination of laminations, less porosity, greater wet and dry strength, were among the claims put forth for this process. All of these features are exceedingly desirable characteristics in the manufacture of a zinc retort. A preliminary test, which involved truck transportation of deaired slugs over a relatively long distance, did show the value of many of these characteristics in forming the retort. Results from the standpoint of , longer retort life in the smelting furnace were not outstanding. The idea lay dormant for several years but was revived again in 1940, when it was decided to make whatever changes were necessary in the equipment for pottery manufacture to fully demonstrate the process. A number of the manu- facturers of machinery for clay work were asked to submit proposals, and the plan finally adopted was extremely simple and economical. Machine FOR DeaeRRATING Selection of the ''Straight-line'' principle for conversion of the "Wettengel" pug mill to a ''vacuum-extrusion" machine preserved some usable parts of the original equipment, such as the drive mechanism, and main shaft. The converted machine consists of a feed hopper, a compression and shredding zone, a vacuum chamber, and an extrusion barrel, as shown in Fig. I. In operation the clay mix travels from the feed hopper into the compression zone, where it is compressed and finally forced around the tapered cone into the vacuum chamber. As it enters this chamber the clay body is shredded into thin plates, for exFosure to the vacuum. The shredder consists of a hub mounted on the main shaft, to which are bolted segmental sections, each of which carries shredder knives. The compression zone and extrusion barrel function as seals for the vacuum chamber and the shredded clay mix is agitated thoroughly during its exposure to the vacuum. A vacuum pump, equipped with a 3-hp. motor, is attached to this chamber, and maintains 25 to 26 in. vacuum during operation of the mill. Changes in Practice Prior to the adoption of the deaeration process, our standard pottery practice called for double mixing in the combination 7

Jan 1, 1944

By R. E. Salvoti

IN underground coal mining, the increasing trend towards mechanical methods is ever apparent. Figures for 1939 showed that 28 per cent of the total bituminous coal production was mined mechanically 1940 statistic will reveal an even higher figure. Factors causing this trend are varied, but the important are the following;

Jan 1, 1941

By Shiou-Chuan Sun

THE effects of oxidation on the flotation behavior of sulphide minerals have been extensively studied 1-3 but no similar study has been made of coals. Coals of bituminous and lower rank undergo atmospheric oxidation during mining and storage, and their degree of oxidizing increases with temperature, 4,5 and time of exposure." The problem of recovering fine oxidized coal from culm piles, rivers, and streams by froth flotation has become increasingly important to the coal industry as well as to those concerned with air and stream pollution. This paper describes the flotation behavior of oxidized and unoxidized coals and carbons in the presence of oily collectors and presents the reagents found effective in the flotation of oxidized coals and carbons. Except where otherwise stated, flotation tests were performed in a 50-g Denver flotation cell. Solid feed for each test was 30 g, and the pulp dilution was kept at 8.5. The —65 mesh coal sample was wetted by agitation with water in the flotation cell for 6 min, then conditioned with a predetermined amount of collector for 2 min, and finally floated with pine oil as frother for 3 min. The oxidation of coals and carbons was performed in a vertical, electrically heated glass tube, shown in Fig. 1. One hundred grams of —65 mesh coal were fed into the glass tube and heated to 10° to 20 °C below the predetermined temperature of oxidation. Compressed air was admitted to the tube at a rate of 0.05 cu ft per min and the temperature was controlled by a variable voltage regulator. The oxi-

Jan 1, 1955

By Jay R. Burns

Two magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or AM265 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains g per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,1,2 however, demonstrates that H and C alloys are replaced by A8 and AZ91, respectively. That is, A8 represents a magnesium alloy having superior toughness while AZ91 is suitable for high yield strength and pressure-tight applications. The basic difference between the American and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars.3 In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ91 alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. [ ] The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity5 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By David Kramer, Cecil G. Rhodes

Critical transport currents were measured as a function of perpendicular external magnetic field in Ti-22 at. pct Nb wire samples. These samples were heat-treated to yield w Phase precipitates at denslties ranging from 10 to 10 17cm-3. The Precipitates are ellipsoids of revolution with major axes of 50 to 1300A. Flux-Pinning by w precipitates is responsible for the high critical transport currents that were ob- ThE ability of a type II superconductor to sustain a zero-resistance transport current (Jc) in an external magnetic field (H) is due to the presence of micro-structural features which can impede the motion of magnetic flux penetrating the superconductor under the influence of a Lorentz force. Such features are referred to as pinning sites. The pinning strength is tained. A sample cooled from 800°C and annealed 1 hr at 450°C carried a critical tramport current of 10 amp per sq cm at 30 kG. Variations in the current-carrying ability of this alloy are due to changes in its pinning strength which is a function of precipitate density and composition and of the composition of the matrix. the reaction of the bulk superconductor to the Lorentz force and depends on the efficiency of the individual pinning sites and on their volume density. The super -current density increases with pinning strength, other things being equal. The above concepts are discussed in detail in a comprehensive review by Livingston and Schadler.' In Ti-Nb alloys, as in other binary titanium alloys, the metastable hexagonal w phase usually forms below the p/a + p phase boundary near the titanium side of the phase diagram. Stiegler et a1.' have summarized much of what is known about w phase in titanium and zirconium binary alloys. The present work deals with

Jan 1, 1968

Separates of all the Technical Publications published in 1930 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the TRANSACTIONS. Copies of these papers have been mailed to those members of the Institute who are registered in Classes A-Mining Methods; B-Milling and Concentration; C-Iron and Steel Division; D-Non-ferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Non-metallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting, respectively. Other members may obtain copies by writing to the Secretary. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. METAL MINING TECH¬ NICAL PUBLI- TITLE AUTHOR MEETING TRANS CATION VOLUME No. AND PAGE* 264-A.29. Quicksilver Industry in 1929. Im- L. H. Duschak San Francisco T30, 283, 312 provements in the Metallurgy of C. G. Maier and Oct., 1929 Quicksilver and Symposium on The others Present Status of the Quicksilver Industry (With Discussion) (37) 271-A.30 Observation on Ground Movement R. E. Palmer New York T30,168 and Subsidences at Rio Tinto Feb., 1930 Mines, Spain (20) 274-A.31 Development and Installation of the C. L. Berrien New York T30, 139, 166 Hawkesworth Detachable Bit (29) . Feb., 1930 276-A.32 Protective Measures Against Gas O. A. Glaeser New York T30, 129, 187 Hazards at United Verde Mine (11) Feb., 1930 287-A.33 Use and Cost of Compressed Air (12) R. S. Lewis New York Feb., 1930 314-A.34 Miami Copper Company Method of F. W. Maclennan New York T30, 39, 80 Mining Low-grade Orebody (44) Feb., 1930 319-A.35 How Human Beings Respond to W. J. McConnell New York Changing Atmospheric Conditions Feb., 1930 (9)

Jan 1, 1930

The Committee submits the following report: The General Committee met in the Treasury Building at Washington on Oct. 6 and 7, 1919. At the first meeting, Cornelius P. Kelley was appointed chairman, and Paul Armitage, secretary of the Committee. Subcommittees were appointed on Invested Capital, on Mine Valuation, and on Depletion and Depreciation. These subcommittees were directed to meet separately and to report on Oct. 7 to the General Committee. On Oct. 7, the reports of these committees were submitted to the General Committee and on motion were received and referred to the Executive Committee for its information to be used as it deemed wise. A motion was carried that the Executive Committee be constituted a permanent committee to continue the work of the Committee, with full power to add to and increase its membership; that as thus increased it should constitute a permanent organization to act and cooperate with the Treasury Department in matters of mining taxation under the Federal Income and Excess Profits Tax Laws. Thereafter the Executive Committee met and formed a permanent committee as follows: Cornelius F. Kelley, chairman, 42 Broadway, New York City. J. L. Darnell, Office of the Commissioner of Internal Revenue, Washington, D. C. J. Parke Channing, 61 Broadway, New York City. Walter Douglas, 99 John St. New York City. R. V. Norris, 542 Second National Bank Bldg., Wilkes-Barre, Pa. J. E. Spurr, care of Engineering & Mining Journal, 10th Ave. and 36th St., New York City. W. G. Swart, 808 Selwood Bldg., Duluth, Minn. J. P. Finley, 45 Cedar St., New York City. W. A. Williams, Bartlesville, Okla. F. S. Peabody, care of Peabody Coal Co., McCormick Building, Chicago, Ill. Matthew C. Fleming, 71 Broadway, New York City. H. B. Fernald, 54 Wall St., New York City.

Jan 1, 1923

The Committee submits the following report: The General Committee met in the Treasury Building at Washington on Oct. 6 and 7, 1919. At the first meeting, Cornelius P. Kelley was appointed chairman, and Paul Armitage, secretary of the Committee. Subcommittees were appointed on Invested Capital, on Mine Valuation, and on Depletion and Depreciation. These subcommittees were directed to meet separately and to report on Oct. 7 to the General Committee. On Oct. 7, the reports of these committees were submitted to the General Committee and on motion were received and referred to the Executive Committee for its information to be used as it deemed wise. A motion was carried that the Executive Committee be constituted a permanent committee to continue the work of the Committee, with full power to add to and increase its membership; that as thus increased it should constitute a permanent organization to act and cooperate with the Treasury Department in matters of mining taxation under the Federal Income and Excess Profits Tax Laws. Thereafter the Executive Committee met and formed a permanent committee as follows: Cornelius F. Kelley, chairman, 42 Broadway, New York City. J. L. Darnell, Office of the Commissioner of Internal Revenue, Washington, D. C. J. Parke Channing, 61 Broadway, New York City. Walter Douglas, 99 John St. New York City. R. V. Norris, 542 Second National Bank Bldg., Wilkes-Barre, Pa. J. E. Spurr, care of Engineering & Mining Journal, 10th Ave. and 36th St., New York City. W. G. Swart, 808 Selwood Bldg., Duluth, Minn. J. P. Finley, 45 Cedar St., New York City. W. A. Williams, Bartlesville, Okla. F. S. Peabody, care of Peabody Coal Co., McCormick Building, Chicago, Ill. Matthew C. Fleming, 71 Broadway, New York City. H. B. Fernald, 54 Wall St., New York City.

Jan 1, 1923

Mine Taxation On Monday morning, Sept. 22, a session on- Mine Taxation was held in cooperation with the Internal Revenue Dept., U. S. Treasury, Mr. R. C. Allen presiding. This was followed by two adjourned sessions, at which Mr. R. C. Allen and Mr. A.D. Brokaw presided. The following paper was presented: Federal Taxation of Mines. By L. C. Graton. (Presented by the author; dis¬cussed by R. V. Norris, W. O. Hotchkiss, W. P. Beldon, Paul Armitage, R. C. Allen, E. F. Brown, William Belly, A. D. Brokaw, F. W. Sperr, C. H. Benedict, E. P. Griffitts, W. E. Forsythe, and the author). Coal and Gas The first session on Coal and Gas was held on Monday morning, Sept. 22; the second, on the afternoon of the same day. Mr. Curl Scholz presided at both sessions. The following papers were presented: Research on the Coal-mining Industry. By E. A. Holbrook. (Presented by the author.) Some Factors that Affect the Washability of a Coal. By Thomas Fraser and H. F. Yancey. (Presented by the author.) A Use Classification of Coal. By George H. Ashley. (Presented by title.) Distribution of Anthracite. By A; S. Learoyd. (Presented by title.) Height of the Gas Cap in the Safety Lamp. By C. M. Young. (Presented by the author.) Engineering Features of Modern Large Coal Mines in Illinois and Indiana. By C. A. Herbert and C. M. Young. (Presented by the authors.) Gas-producer Practice. By G. S. Brooks and C. C. Nitchie. (Presented by the authors.) Testing of Coals for Byproduct Coking and Gas Manufacture. By Horace C. Porter. (Presented by the author.) Coals of Ohio and their Limitations for Byproduct Coke. By Wilber. Stout. (Presented by the author.) Outdoor Substations in Connection with Coal-mining Installations. By H. W. Young. (Presented by the author.)

Jan 11, 1919

By Joseph Hartshorne

EVER since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published' that, in Germany alone, the loss from the first of the above causes amounts to 500,000 marks per year. The loss from the second cause is, of course, much greater. A process for saving this entire loss, in use at Teplitz, Bohemia, for about three years, would seem to be of value even in this country, where coal is cheaper and where the small economies are not watched as closely as they are in Europe. This process, invented by Mr. Adelbert Kurzwernhart, late Technical Director of the Teplitzer Walzwerk, has been worked out with thoroughness. The loss from each cause can be calculated very closely for any particular furnace, and the results to be expected from the process ascertained. It can easily be decided, therefore, whether it is worthwhile to adopt it under any given conditions. The amount of chamber-gas lost depends upon,-(1), the cubic contents of the chamber, ports and flues upon one side of the furnace, up to the reversing-valve (deducting, of course,

Mar 1, 1906

By Blair R. Benner

This paper describes the installation and operation of a Texas Nuclear on-line silica analyzer (NOLA) coupled with a Leeds and Northrup Microtrac particle-size monitor (Microtrac) at U.S. Steel's Minntac taconite concentrator. An automatic sampling system provides the NOLA with samples of final concentrate. After the sample is analyzed for silica by the NOLA, it is pumped to the Microtrac for size and surface area measurement. A sample is analyzed every six minutes, providing the control room with the silica concentration, the percent passing 270, 400, and 500 mesh, and an equivalent Blaine surface area number. When fed a slurry of final concentrate containing between 20 and 70% solids and 5 to 6% silica, the NOLA analysis is within ±0.2% of the wet chemistry silica. The agreement between the Microtrac output and standard screen analyses is ±1.2% at 270 mesh; ±1.5% at 400 mesh, and ±2% at 500 mesh. The poorer disagreement at the finer sizes is mainly due to inaccuracies in screening at 400 and 500 mesh. The agreement between Microtrac surface area a d laboratory Blaine surface area is about 9 ±80 cm 2/g. These instruments provide rapid and reliable feedback information to the concentrator and feed forward information to the agglomerator.

Jan 1, 1984

By L. Graydon Carpenter, Donald E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO3. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about L. G. CARPENTER and D. E. GARRETT are with the Research Dept., American Potash & Chemical Corp., Trona, Calif. TP 47881. Manuscript, Nov. 4, 1958. AlME Trans., Vol. 214, 1959. 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley.

Jan 3, 1959

By B. E. Field

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The com¬mercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depending upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

The following is an incomplete list of members and guests who called at Institute headquarters during the period May 10, 1919, to June 10, 1919. Victor C. Alderson, Golden, Colo. E. Fleming L'Engle, Joplin, Mo. H. Foster Bain, Washington, D. C. W. D. Mainwaring, Philadelphia, Pa. J. J. Beeson, Master Engr. Sr. Gr. W. G. Matteson, Fort Worth, Tex. Gunnar Bergstrom, Stockholm, Sweden. C. E. MacDonald, Toronto, Can. Corry T. Brown, Socorro, N. Met. Francis Nicholson, Charlotte, Va. Geo. W. Brymer, Scranton, Pa. Richard A. Parker, Denver, Colo. W. Burns, Santa Fe, N. Mex. S. B. Patteson, Jr., Allentown, Pa. H. C. Carlisle, The Pas, Manitoba, Can. G. W. Ponton, Ottawa, Canada. J. Carson Adkerson, Va. W. H. Reber, Ensign, Dallas, Tex. C. A. Cheney, Madison, Wis. T. C. Roberts, New York City. J. M. Clark, Toronto, Canada W. A. Rukeyser, Ensign, N. F. Corps. John J. Doyle, St. Louis, Mo. W. H. Staver, New York City. H. S. Emlaw, Grand Haven, Mich. D. B. Sterrett, Washington, D. C. E. Francis, Birmingham, Ala. T. V. Smirnoff, Russia. Rudolf Gahl, Denver, Colo. E. C. Templeton, New York City. Emit Gthmann, Baltimore, Md. H. A. Toblemann, Ajo, Ariz. A. B. Hardie, Philadelphia, Pa. Priestley Toulmin, Birmingham, Ala. Clarence M. Haight, Franklin, N. J. M. R. Walker, Baltimore, Md. N. V. Hansell, New York City. H. A. Wheeler, St. Louis, Mo. C. A. Heberlein, Nacosari, Mexico. D. B. Whitaker, Santiago, Cuba. Pierre Hines, Milwaukee, Wis. A. W. G. Wilson, Ottawa, Can. J. S. Hollings, Brymoba, Wales. Oba Wiser, Hanover, N. Mex C. Vey Holman, Maine. Harry J. Wolf, Denver, Colo. H. H. Howry, Denver, Colo. F. H. Wood, Mt. Vernon, N. Y. W. Spencer Hutchinson, Boston, Mass. J. P. Wood, New York, N. Y. W. B. Kunhardt, Reading, Pa. Lawrence Addicks sailed on May 17 for London; lie expects to be absent from this country for several months. Roy H. Allen has accepted a position in the research engineering department of the National Aniline & Chemical Co., Buffalo, N. Y. H. Foster Bain has gone to Shanghai, China, where he expects to remain for some time. Percy J. Bandy has accepted a position with the Cia. Minera del Mirasol S. A., at Cusihuiriachic, Chihuahua, Mexico. J. H. Batcheller is now with the North Midas Copper Co., St. Helena, Alaska.

Jan 7, 1919

The Library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions are forced to spend a portion of their time in localities isolated from sources of information. To these the Library; through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention: The Library is prepared, to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general Information on the geology and mineral resources of-all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. HARRISON W. CRAVER, Director.

Jan 4, 1919

By P. D. Zemany, G. W. Sear, B. W. Roberts

Vanadium metal is embrittled by hydrogen at a temperature as low as 250°C when held in the presence of manganese metal and water vapor in a rough vacuum. It is established that the property changes are caused by the catalytic decomposition of water vapor at the vanadium surface and the diffusion into and solution in the vanadium of the resultant hydrogen. It is found that manganese is a necessary component of the catalyst. The manganese is transported in the vapor phase by an unknown molecule. A deuterium tracer experiment demonstates the role of water vapor in the embrittle-ment process. VANADIUM metal foils were observed to become embrittled' at a temperature of about 300 °C when held in the presence of manganese metal and a small amount of moist air, This paper describes the investigation to find the embrittling agent and an understanding of the relatively low temperature reactions that are involved. Experimental The vanadium metal foil used was prepared by cold-rolling and pack-rolling 32 mil sheet" in a series of steps down to 1 mil foil. The original observation was confirmed by sealing vanadium foils of 3 x 10 sq cm into individual Pyrex tubes with manganese powder† and a con- trol tube containing only the vanadium foil. These tubes were evacuated to 10 -5 mm Hg without baking and sealed. After heat treatment for 200 hr at 300°C, the control foil showed no change in duetility, whereas the foil contained in the manganese— containing tube was embrittled. The visual appearance of each was unchanged. A series of Pyrex sample tubes, about 2.5 cm diam and 25 cm long, were prepared, each containing a 3 x 10 sq cm piece of foil and 5 g manganese powder at the lower end of the tube. By reducing the time of anneal and the temperature of these samples, it was found that embrittlement could be created at 250°C in a time as short as 1 hr. Since the vanadium metal used here has been drastically cold-worked by rolling, it is assumed that it contains a maximum number of dislocations. To check the possible necessity of dislocations in this low temperature reaction, a vanadium foil sample was annealed in Vycor for 2 hr at 800°C to re crystallize and reduce the dislocation concentration. Metallographic examination showed grains which were not visible before annealing. The embrittlement procedure was carried out at 300°C and 3 hr. Upon checking the foil no embrittlement was observed. Further experiments demonstrated that about 6 hr at 300°C are required to create embrittlement in the foil. This delay in the onset of embrittlement in the vanadium foil suggests but does not prove that dislocation channels play a role in the embrittlement phenomena. If manganese metal is necessary for this low temperature embrittlement, do other elements in the transition metals group yield the same result? To check this qualitatively, a group of elements of similar atomic radii were obtained and sealed as before into Pyrex tubes with a sheet of vanadium foil. These tubes were annealed at 250°C for 6 hr and included (with radii)-2 A1 (1.4A), As (1.25A), Be (1.2A), Co (1.25A), Cr (1.45A), Cu (1.25A), Fe (1.25A), Ga (1.2A), Ge (1.25L%), Mn (1.3A), Ni (1.25A), Si (1.2A), Ti (1.45A), Zn (1.3A), air, H,O, 10 cm Hg of dry hydrogen, and MnO, powder. Upon testing the above sample foils for brittleness, only the manganese-containing tube yielded a brittle foil. Manganese Transport—To eliminate contact of manganese metal powder and vanadium foil, sample tubes were prepared with fritted glass barriers. The embrittlement reaction was still found to occur. Thus, the mode of transfer of manganese is certainly vapor transport. A vanadium foil was embrittled by this mechanism in an evacuated Pyrex tube for 8 hr at 300°C. By means of X-ray fluorescence analysis,' the amount of manganese added to the surface was established at 5 ±2 x 10 -6 g per sq cm. Since the average rate of manganese deposition is known, an effective average pressure of an assumed carrier compound can be computed. ___ P = M/T v2p mkT

Jan 1, 1959

By Francis P. Sinn

LOW prices have made 1938 a difficult year for the zinc industry of the world. Particularly in the United States, output had to be radically curtailed to bring production into line with consumption. Despite these unfavorable conditions, some additional plant construction is contemplated. In Jugoslavia, through co-operation with the Government, Trepca Mines is lo build a zinc plant to produce 10,000 metric tons annually, the plant to be ready for operation in July, 1941). Cerro de Pasco is proceeding with its plans for an electrolytic plant in Peru. A pilot plant, to be ready next summer, is under construction. In eastern Canada an electrolytic plant is planned in Quebec to treat concentrates from Yoranda and other mines but no defi-

Jan 1, 1939

El Indio, eighty percent -owned by Compania Minera an Jose Inc., a subsidiary of St. Joe Minerals, and twenty percent-owned by private Chilean investors, will open their new flotation and Carbon -In -Pulp plant near La Serena, 480 km (300 miles) north of Santiago, Chile, in early 1981. The underground mine, at an altitude of 4,270 m (14,000 ft), will produce about 1,270 mt per day (1,400 st per day) of ore containing about 2. 2570 Cu, and gold and silver to the extent of 16 and 254 g per mt (0.47 and 7.4 oz per st) respectively. While construction of the plant was underway, development ore, containing some 1,400 kg (45,000 oz) of gold, was shipped to the United States for recovery in a copper smelter. At El Indio the underground ore is rail-hauled to the mill a short distance from the portal where it is crushed, ground, and floated to produce a copper concentrate containing both gold and silver. The crushing plant also crushes waste for use as mine backfill. Approximately 92% of the copper and 60% of the gold and silver are recovered in the flotation concentrate. Flotation tailings, at a grade of 19 g Au and 116 g Ag per mt (3.4 oz Au and 0.55 oz Ag per st), are cyanided for 72 hours in six Pachucas with auxiliary air lifts for pulp transfer. Lime, cyanide, lead nitrate, and a phosphate are also fed to the cyanidation Pachucas. After cyanidation, the pulp is treated in four air lift Carbon-In-Pulp tanks equipped with external vibrating screens for carbon advance. Loaded carbon is stripped in two pressure vessels in parallel. Pressure stripping must be used because of the high altitude. Stripped carbon is dewatered in a spiral classifier before being reactivated in a rotary kiln and returned to the C. I. P. circuit. Pregnant solution is then sent to four banks of four Zadra cells for gold and silver recovery on steel wool. Zadra cell cathodes.are washed with the slimes being captured in a plate and frame filter. The filter cake and the washed cathodes are then dried on an infrared dryer and smelted in two stages to bullion bars. Published reports indicate that the total investment for this unique operation was in the neighborhood of $80 million.

Jan 1, 1981

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By AIME AIME

MOST recently elected to the limited group of Honorary Members in the A.I.M.E. is the distinguished Australian metallurgist, Guillaume Daniel Delprat. His citation reads: "in recognition of his distinguished achievement as metallurgist, engineer, and administrator in the production of ferrous and nonferrous metals," Mr. Delprat's ability and experience in both the ferrous and nonferrous fields at once distinguishes him from most of his professional brothers. Mr. Delprat's nativity was neither Australian nor English, for he was born in Delft, Holland, in 1856, and educated in Amsterdam. At the age of 22 he went to Spain, as metallurgist for the Tharsis Sulphur and Copper Co., Ltd. Afterwards he spent some time with the Bede Metal and Chemical Co., which had mines in both Spain and Norway, and of which company he became general manager. Other positions of responsibility held by Mr. Delprat before he went to Australia included the managing directorship of the Cordova Exploration Co., with properties in Spain and Canada; of the Rincon Silver-Lead Mining Co., in Spain; and of the Deloro Gold Mines, in Canada.

Jan 1, 1936