Search Documents

By Louis A. Panek

The purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fen tress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal held exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The miaximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repiesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: Safe R =(1/4)4p2n2r/g=p2n2r/g [I] in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sec2.

Jan 1, 1949

By P. L. De Bruyn

The adsorption density of dodecylammonium ions at the quartz-solution interface has been Theadsorptiondensitydetermined as a function of collector concentration and pH. A ten thoushasbeenandfold range of amine salt concentration was covered at neutral pH. Experimental results show that over a thousandfold concentration range at neutral pH, the adsorption density (I) is proportional to the square root of collector concentration. Except at high concentrations, I increases with increases with increasing pH, but in general this effect is surprisingly small. . , . . A critical pH curve has been established for the flotation of quartz with dodecylammonium acetate. The conditions along the flotation curve are correlated with the adsorption measurements. THE behavior of collectors at the mineral-solution interfaces is usually explained in terms of an ionic adsorption process. Through the distribution of collector ions between the solid surface and the- co-existing solution phase the mineral is believed to acquire a water-repellent surface coating. Quantitative adsorption studies have been made on simple flotation systems1-4 only within the last few years. Such investigations were made possible by the adoption of the radiotracer method of analysis. As a consequence of these studies a new parameter has been added to aid the understanding of the flotation process. The research investigation to be discussed in this paper was undertaken to obtain a better understanding of the behavior of a cationic-type collector. This objective was approached through the determination of the distribution of dodecylammonium acetate between the quartz-solution interface and the solution as a function of the collector salt concentration and pH. To bring this investigation to focus on the more practical aspect of flotation research, an attempt was also made to correlate the adsorption results with actual flotation tests. Quartz: A —100 mesh ground crystalline quartz was infrasized; the products of the third and fourth cones were mixed together and reserved for experimental purposes. This stock material was cleaned by leaching in boiling concentrated HC1. After leaching the quartz was rinsed with distilled water until the filtrate showed no trace of chloride ian. It was then washed several times and dried. The qwrtz had a specific surface of 1400 cma per g as deterhined by the krypton gas adsorption method. Collector: The distribution of dodecylammonium acetate between the quartz surface and the solution phase was determined by the radiotracer method of analysis with carbon 14 as the tracer element. The radioactive amine salt with C" synthesized into the hydrocarbon chain5 was supplied by Armour and Co. The tracer element was located adjacent to the polar group. The radioactive salt as received had a specific activity of about 0.14 mc per g. When desired, dilution of this activity was effected by addition of non-radioactive dodecylammonium acetate also supplied by Armour and Co. ........ All other inorganic reagents used in this research were of reagent grade. Conductivity water was used for making up all solutions. Adsorption Tests: Two different experimental methods were used. In the first, to be designated as the agitation method, a weighed amount of quartz and a measured volume of amine salt solution were agitated in a 100-ml or 50-ml glass-stoppered pyrex graduated cylinder. The cylinder was filled with solution up to the stopper, since erratic results were obtained when an air space was left over the suspension. Time of agitation varied from 1 to 2 hr. Preliminary tests at different agitation times showed that the amount adsorbed remained constant for all agitation times exceeding 1/2 hr. After this conditioning period, the solids were separated from the solution by filtration through a Buechner fritted-disk funnel. The solution was re-circulated 10 times or more to allow the fused silica disk to come to equilibrium with it. Determinations of the amount of amine adsorbed on the frit itself indicated that this amount was less than 10 pct by weight of the amine acetate abstracted by 10 g of quartz. The funnel with quartz covered by a thin layer of solution was then centrifuged for approximately 5 min, at which time the moisture content of the solids was reduced to about 5 pct by weight. The wet quartz was blown into a tared beaker, re-weighed and allowed to dry at room temperature. A final weighing was then made to determine the moisture content. The second experimental method, similar to the procedure adopted by Gaudinand Bloecher,' will be referred to as the column method. Two liters of solution were passed through a bed of quartz contained in a Buechner funnel attached to a pyrex separatory funnel by means of a ball and socket joint. Preliminary tests showed that increasing the volume of solution above 2 liters does not give a measurable increase in adsorption. From 4 to 4 1/2 hr were required for 2 liters of solution to pass through the column. The moisture content of the quartz was again reduced to a minimum by centrifuging. A slightly modified column apparatus was used for experimenting with alkaline amine solutions. The same basic unit was used, but the underflow from the Buechner funnel was again fed into a Separafory

Jan 1, 1956

By F. O., Garrabrant

ELECTRIC power requirements for Climax are similar to those of most metal mines, except that large blocks of power are used underground and there are a number of other unusual applications. Power is furnished to the Company by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are designed so that with the addition of forced cooling their capacity may be increased a third at 12,000-ft. altitude. On the secondary side of this bank is a 15-kv., 1200-amp. oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. (A more complete description of the electrical distribution system at Climax, with detailed drawings, is contained in T.P. 1734, A.I.M.E., Mining Technology, July, 1944.)

Jan 1, 1946

By Benjamin C. Craft

Oil and gas development in Louisiana during 1935 brought this state at the close of the year up to fourth place in the nation as a producing area. A review of development in North Louisiana centers around Rodessa, the most important reserve discovered in this area in many years. While the producing limits have not been defined, this discovery is one of the major developments of the year. New gas fields were discovered in Lincoln, De Soto and Bossier parishes. The Lincoln Parish discovery, completed flowing a highly saturated gas from the Glen Rose, further indicates the importance of deep-seated prospects in the interior salt-dome area. Minor extensions were made at Sligo and Pine Island. During the year, 126 oil wells and 103 gas wells were completed in North Louisiana as compared with 144 oil wells and 68 gas wells during 1934. The North Louisiana oil production was 9,617,405 bbl. as com-pared with 9,274,050 bbl. during 1934, an increase of 343,355 bbl., while the gas production increased 18 billion cu. ft. in 1935 over its 1934 figure. The Louisiana Department of Conservation gage of Nov. 1, 1935, shows an open-flow capacity of 4,563,725,000 cu. ft. per day from 941 wells in the Monroe field and 682,770,000 cu. ft. from 159 wells in the Rich-land field. A great deal of leasing continues in North Louisiana as a result of the Lincoln Parish discovery and development in the Rodessa field, especially in Bossier, De Soto, Winn, Lincoln, Bienville, Webster, Ouachita and Richland parishes. South Louisiana's position as an area of important reserves was further proved during the past year. Increased drilling resulted in the discovery of seven new fields: Lafitte, Garden Island Bay, Tepetate, Bunkie, St. Martinsville, Jeanerette and Big Lake. New sands or producing horizons proved productive in 15 of the proven fields. The total oil production for South Louisiana during 1935 was 40,731,-056 bbl. as compared with 23,255,437 bbl. during 1934. There were 222 oil and gas wells completed in South Louisiana during 1935 as compared with 214 oil wells during the previous period. Drilling during

Jan 1, 1936

By Benjamin C. Craft

Oil and gas development in Louisiana during 1935 brought this state at the close of the year up to fourth place in the nation as a producing area. A review of development in North Louisiana centers around Rodessa, the most important reserve discovered in this area in many years. While the producing limits have not been defined, this discovery is one of the major developments of the year. New gas fields were discovered in Lincoln, De Soto and Bossier parishes. The Lincoln Parish discovery, completed flowing a highly saturated gas from the Glen Rose, further indicates the importance of deep-seated prospects in the interior salt-dome area. Minor extensions were made at Sligo and Pine Island. During the year, 126 oil wells and 103 gas wells were completed in North Louisiana as compared with 144 oil wells and 68 gas wells during 1934. The North Louisiana oil production was 9,617,405 bbl. as com-pared with 9,274,050 bbl. during 1934, an increase of 343,355 bbl., while the gas production increased 18 billion cu. ft. in 1935 over its 1934 figure. The Louisiana Department of Conservation gage of Nov. 1, 1935, shows an open-flow capacity of 4,563,725,000 cu. ft. per day from 941 wells in the Monroe field and 682,770,000 cu. ft. from 159 wells in the Rich-land field. A great deal of leasing continues in North Louisiana as a result of the Lincoln Parish discovery and development in the Rodessa field, especially in Bossier, De Soto, Winn, Lincoln, Bienville, Webster, Ouachita and Richland parishes. South Louisiana's position as an area of important reserves was further proved during the past year. Increased drilling resulted in the discovery of seven new fields: Lafitte, Garden Island Bay, Tepetate, Bunkie, St. Martinsville, Jeanerette and Big Lake. New sands or producing horizons proved productive in 15 of the proven fields. The total oil production for South Louisiana during 1935 was 40,731,-056 bbl. as compared with 23,255,437 bbl. during 1934. There were 222 oil and gas wells completed in South Louisiana during 1935 as compared with 214 oil wells during the previous period. Drilling during

Jan 1, 1936

By C. C. Hatch, C. R. Larsen, A. L. Mular

INTRODUCTION As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer/winter of 1975 and during the summer of 1978 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses, to permit study of alternative circuit configurations if desired and to perform off-line optimization. This chapter describes the methodology employed to develop the simulator (1,2) along with typical applications thereof. SECONDARY CRUSHING PLANT FLOWSHEET Figure 1 is a schematic diagram of the Brenda Mines Ltd. secondary crushing plant circuit. The 41,000 tonne coarse ore stockpile(a) is -17.8 cm oversize (3B belt) from two 2.4 m x 6.1 m double deck vibrating screens (not shown). The screens are fed by 2 conveyor belts operated in series with two 198 cm apron feeders that handle discharge from a 152 cm x 226 cm primary gyratory crusher(520 KW). The primary crusher (not shown) treats up to 2725 tonne/hr of run of mine ore. Minus 1.9 cm undersize from the primary screens (#19 belt), referred to as the primary fines, joins secondary screen undersize (#18 belt) for conveyance to fine ore bins (not shown). Feed from the coarse ore stockpile is transferred by means of vibrating feeders and two 120 cm conveyors (#6 and #7) to transfer belts #8 and #9 (Figure 1). The belts feed two secondary 2.1 m standard heavy duty cone crushers (bl and b2). Each crusher is equipped with a modified coarse mantle liner and a standard coarse bowl liner. Mantle throw is 9.2 cm; nominal close side set is 3.2 cm. Crusher .countershafts (443 rpm) are driven by single 260 KW synchronous motors (710 rpm). Discharge from the secondary cone crushers joins discharge from four 2.1 m tertiary heavy duty shorthead cone crushers (fl, f2, f3 and f4). With the exception of the cavity (modified medium mantle liner and standard coarse bowl liner; close side set is nominal .84 cm) and motor (224 KW), these machines are similar to the secondary crushers. The combined discharge is transferred from a 183 cm conveyor to #14 belt which empties into a 1452 tonne secondary screen surge bin (c). Vibrating feeders beneath the bins feed five 2.4 m x 6.1 m double deck vibrating screens (dl, d2, d3, d4 and d5) sloped at 200 from the horizontal. The upper decks are punched plates with 2.7 cm x 7.6 cm slots. Lower decks are woven wire (1.27 cm diameter) sections with

Jan 1, 1982

Discussion of the paper of Frank H. Kneeland, Safeguarding the Use of Mining Machinery. By B. F. Tillson and Arthur Williams. 1073 Discussion of the paper of Howard N. Eavenson, Safety Methods and Organization of United States Coal & Coke Co. By William H. Grady, Thomas W. Dawson, C. W. Goodale, J. Parke Charming, B. F. Tillson, George S. Rice, Arthur Hovey Storrs, Harry H. Stoek, Lawson Blenkinsopp, Arthur Williams, and Howard N. Eavenson. 1075 Discussion of the paper of J. Parke Channing, Enlarging the Worth of the Worker and the Perspective of the Employer. By Fred H. Rindge, Jr., S. A. Taylor, Elmer L. Corthell, and Philip W. Henry. . 1095 Discussion of the paper of Walther Mathesius, High Blast Heats in Mesaba Practice. By Joseph W. Richards, W. A. Forbes, J. E. Johnson, Jr., H. P. Howland, and Walther Mathesius. . 1100 Discussion of the paper of W. R. Shinier, Effect of Finishing Temperatures of Rails on Their Physical Properties and Microstructure. By William R. Webster, Henry M. Howe, A. A. Stevenson, G. K. Burgess, and Samuel L. Hoyt . 1107 Discussion of the paper of George K. Burgess and Sir Robert A. Hadfield, Sound Steel Ingots and Rails. By Albert Sauveur, Henry M. Howe, Henry D. Hibbard, Joseph W. Richards, F. W. Wood, and George K. Burgess. . 1112 Discussion of the paper of Henry M. Howe and Arthur G. Levy, Are the Deformation Lines in Manganese Steel Twins or Slip Bands? By J. E. Stead 1116 Discussion of the paper of F. C. Langenberg and R. G. Webber, Structures and Hysteresis Loss in Medium-Carbon Steel. By Henry M. Howe. . . 1117 Discussion of the paper of Charles H. MacDowell, German and Other Sources of Potash Supply. By George S. Rice, Charles H. MacDowell, and V.C. Grubnau . . 1118 Discussion of the paper of Joel H. Watkins, White-Burning Clays of the Southern Appalachian States. By H. Ries 1120

Jan 5, 1915

By Wayne A. Greenwalt

A method that determines venture participation when the decision maker's level of risk aversion varies according to venture profitability and risk investment is presented. The decision maker's fundamental aversion to risk is established by the selection of a desired working interest for a venture that anticipates only a discounted payout.

Jan 1, 1982

By A. C. Fraker, H. H. Stadelmaier

WIENER and Bergerl reported the existence of the nitrides Fe3NiN and Fe3PtNwith a cubic L1'2 structure. The present note shows that a similar nitride Fe3PdN can be observed and that the composition range between the iron nitride Fe4N and the nitrides Fe3NiN, Fe3PdN, and Fe3PtN is occupied by single-phase cubic nitrides with structures intermediate between L1' and L1'2. The materials used in this investigation were electrolytic iron of 99.9 pct purity, carbonyl nickel of 99.7 pct purity, sponge platinum of 99.95 pct purity, and palladium sheet of 99.8 pct. purity. Binary alloys of the transition metals were induction-melted in a crucible of fused alumina, powdered, and screened to a particle size of - 200 mesh. The powders were nitrided at 600°C in a gas mixture of ammonia and hydrogen, and the crystal structure was determined with the aid of a Wilson powder camera. The results are compiled in Table I together with information from the paper of Wiener and Berger.1 The compound at the nominal composition Fe3PdN has a diffraction pattern with prominent reflections of a face-centered cubic lattice (h2 + k2+l2 = 3, 4, 8, 11, 12, 16) and weaker superstructure lines (h2 + k2 + 12 = 1, 2, 5, 6, 9, 10, 13, 14). With decreasing palladium content the superstructure lines become weaker and approach the intensity of those of Fe4N. No analysis was made of the intensities, but it can be assumed that the structure is that found by Wiener and Bergerl in Fe3NiN and Fe3PtN, namely L1'2 (perovskite structure) with both palladium and the interstitial nitrogen fully ordered. The dependence of the lattice constant upon the solute atom (Ni, Pd, Pt) content can be explained tolerably well by simple lattice expansion due to subsequent work confirms this suggestion, it will be of significance to order-disorder theory. The author is grateful to Lester Guttman for discussions on this topic.

Jan 1, 1961

By Steven T. Mitchell

INTRODUCTION Mill production from the Homestake Mine in 1979 amounted to 1.29 Mt (1.43 million st) of ore containing 5.9 g/t of gold (0.172 oz per st) compared with 1978 production of 1.44 Mt (1.59 million st) containing 6.2 g/t of gold (0.180 oz per st). The average cost per ounce of gold produced in 1979 rose to approximately $250 contrasted with $176 in 1978. This increase in unit cost is the result of inflation, a diminishing ore grade, and productivity losses related to a shortage of experienced miners as well as compliance with federal regulatory requirements. Together, these factors prompted the investigation of several large-scale, highly mechanized underground mining methods. This analysis indicated Vertical Crater Retreat mining to be one of the safest underground methods known today, yet competitive with all other forms of stoping in terms of cost and productivity. Therefore, the feasibility of applying the VCR stoping method at the Homestake Mine was explored. Vertical Crater Retreat stoping is a recent innovation in large- scale underground mining based on C. W. Livingston's crater blasting theories. Figure 1 illustrates the method which consists of drilling 165.1-mm-diameter (6.5-in.) holes from a topsill down-dip to an under- cut on the level below. The bottom of each hole is then loaded from above with a predetermined charge weight and horizontal slices up to 4.27 m (14 ft) in thickness are blasted into the undercut. Broken ore is extracted from drawpoints located on or below the undercut level.

Jan 1, 1983

By S. Terry, J. G. Munro

A unique feature of the recently dedicated pelletizing complex of Hamersley Iron Pty. Ltd. is the dry grinding circuit for the iron ore fines. This facility, located at Dampier, some 800 miles north of Perth, Western Australia, has a rated annual capacity of 2 million tpy of iron ore pellets. The Mt. Tom Price orebody, which supplies the pelletizing plant, is a massive deposit of high-grade hematite containing an estimated 500 million tons of ore averaging 64% iron. The main impurities are ferruginous shales that occur in bands of varying widths in the orebody. An average analysis shows 4.4% SiO2, 2.0% A12O3, 0.05% P and 1.8% LOI.

Jan 5, 1968

By C. Everard Arnold

The Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mine. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising; 15 ft. of sinking was done so that the bearers, collar-set, and three shaftrsets might be installed and concreted, and with this done it mas possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 f't. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. airhoist was installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21 ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8-by 8-in. struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jan 1, 1911

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

E. E. Russell Tratman, New York City (communication to the Secretary): Mr. Glenn's paper brings up again the question of the part played by coal-dust in colliery-explosions. In the discussion of Sir Frederick Abel's paper on " Accidents in Mines," read before the Institution of Civil Engineers,? much was said about the dangerous properties of coal-dust, and several instances were given of the successful use of a spray of water, water and compressed air, or exhaust-steam from an engine, to keep the mine SUEciently damp to prevent the formation of dust clouds. Methods of preventing shots from blowing out; of using water cartridges to prevent flame ; and of using lime cartridges, wedges and other means of breaking down the coal were also discussed. Mr. Emerson Bainbridge referred to the explosive termed " roburite " (ammonium nitrate and

Jan 1, 1895

Prof. Mathesius analyzes the running of Howland's furnace No. 19, according to the method described by him in Stahl and Eisen, 1916, Nos. 30 and, 31, and in his work "Die physikalischen und chemischen Grundlagen den Eisenhüttenwesens" (Spamer, Leipzig). By assuming 500 Cal. lost from the hearth by radiation and cooling water per kilogram of pig iron made, a throat-gas temperature of 600° C., and taking the ratio of C02/CO as 0.64, he finds that his diagram would show 0.68 kg. of carbon oxidized per kilogram of pig iron, while Howland gives 0.66 kg. He expresses himself as well satisfied with this test of the accuracy of his theory. Making the further assumption that the heat losses from the shaft are 1,000 Cal. per kilogram of pig iron (twice as

Jan 5, 1917

By Claude P. Heiner

While the title of this paper embraces the entire West Coast, the author, in the interest of simplification. has confined the discussion to California-particularly the central section. California's population has, risen 45 pct since 1940. Its electric requirements have also increased, not only because of the growth in industry and population but also because of the widespread tendency of all types of electric consumers to use more electricity than ever before. The growth of California's electric utilities is shown by published data covering operations, of three of its large systems and is given in Table 1.

Jan 1, 1949

By John C. Cosgrove

IT was just five minutes past midnight, on Wednesday, Jan. 5, 1938, that Mrs. Cosgrove and I sailed from New York City. Our trip was to completely circle the globe, to cover over 40,000 miles and stop at thirty ports-from New York to Trinidad, to South America, via South Africa to the Orient, to India, to the Malay States, to Indo-China, the Philippines, Australia, New Zealand, Fiji, and across the Pacific home via Honolulu. It is not my intention to make this a complete, technical study of coal or coal mining in the various countries that .we visited but more to outline the general in- formation that the mining engineer and coal operator would absorb in his travels. Coal is the universal fuel and is in use wherever there is commerce and industry. Even on our ship, which, like practically all ocean liners was an oil-burner, a considerable quantity of coal was used for cooking.

Jan 1, 1939

By Kenneth S. Ritchie

TOO often, many foremen; superintendents, managers, and executives, "The Bosses" of the oil and mining industries, do not fully realize: (1) How much personal actions '.on the job" may reduce their effectiveness in getting work done; and, (2) The importance of harmonious relations with their fellow men. Today. these qualities of personality in the people entrusted with the positions of responsibility are more important than ever with the shortages of labor so critical in vital war production. Likewise, many engineers do not fully realize that their work is essentially executive in character; i.e., other people do the actual labor. Without their help. the engineer's work would not be done. A clearer appreciation of this fact would increase their interest: (1) in the nontechnical aspects of their work. and, (2)in their relations with others, particularly the individuals in their own organization. Consequently, these engineers would be more successful in equipping themselves for greater responsibilities and increased remuneration.

Jan 1, 1944

By G. A. Beske, P. Hilsch, J. Wulff

The effects of the growth precipitates on the su-perconduching properties of an Al- 15 al. pel Zu alloy have been studied using magneization, transition lem-perature, and residual resistivity measurements. Aging at 230C for 1/2 to 11 he produces an increase in Hfp, Ike field of first penetration, and tut increase in trapped flux. The upper critical field, Hc2 remains constant for such aging tunes. Aging at 200°C produces a decrease in Hfp and an increase in trapped flux. The transition temperature remains constant at Tc - 1.227° ± 0.02°K for aging at 220°C for tims of from 1/2 to 10 hr, and for aging at 200°C it remains constant at Tc. = 1.18° i 0.02°K for times from 1/2 hv to 26 hr. The observed behavior indicates that the superconducting matrix when aged at 220°C behaves tike a type U su-perconducior, but when aged at 200°C behares like a type I superconductor. The magnetization changes after aging can be attributed to the growth and clutnge in distribution of the precipitate in a matrix of fixed composition. IT has been realized for some time that the superconducting properties of alloys are highly structure-sensitive. This is evident in the work of Mould and Mapother1 who examined the properties of an aluminum alloy. Precipitation effects have also been briefly mentioned in other studies.2-4 Bonnin and coworkers5 have observed a sharp inc rease in trapped flux in an A1-Mg alloy when the residual resistivity reaches a value that indicates it is a type II superconductor. Recently Blanc, Goodman, and Nemoz5p have reported on precipitation effects in A1-Ag alloys. Detailed studies of precipitation in Pb-Sn and Pb-Cd alloys made by Livingston6 serve to show that the upper critical fields are enhanced by quenched-in solute. Furthermore. at various stages in the precipitation process? the upper critical field is determined largely by the remanent solute. The observed magnetic hysteresis and trapped flux in such alloys result from the interaction between precipitate and the flux filaments in the mixed state. The flux trapping appears to depend largely on the precipitate distribution and is greater if the superconductor is type II than if it is type I. To examine the effect of precipitation in another alloy system, particularly one in which the composition of the superconducting phase does not change significantly during the course of precipitation, the Al-Zn system seems interesting, especially in view of the transition temperature and resistivity studies of Chiou and seraphim.' Furthermore, the recent detailed electron-microscope studies of an Al-Zn alloy by Richards and Garwood8 provide a guide for relating superconducting properties to changes in structure. For these reasons, magnetization, transition temperature, and residual resistivity measurements for varying times of heat treatment at two temperatures were made with a -15 at. pct Al-Zn alloy. The results are reported in this paper. I) EXPERIMENTAL The alloy used was prepared by Cominco Products Inc. from 99.9999 A1 and 99.999 Zn. It was chill-cast, swaged, and drawn to 0.125-in.-diam rod. The analyzed composition was 15.6 at. pct Zn (31.1 wt pct). A jeweler's saw was used to cut the 0.125-in.-diam rod into the 0.875-in. lengths needed for magnetization measurements. The ends of the cylinders were slightly beveled to remove the sharp edges. A portion of the original 0.125-in.-diam rod was drawn into 0.010-in.-diam wire and used for transition temperature measurements. Specimens were suspended from wires within a vertical furnace during heat treatment. All were homogenized at 500°C for a minimum of 3 days and subsequently solutionized for times in excess of 6 hr. The solutionizing temperature was held constant to +3°C. Individual specimens were homogenized, quenched, and aged several times and no effects indicating loss of zinc were noted. The suspended specimens were quenched by cutting the wires and allowing the specimens to fall into a silicone oil bath held at the aging temperature. They were then isothermally transforked by aging in the same bath used for quenching. After aging for the required time (approximately 10 min aging was necessary before the upper critical field reached a fixed value), they were briefly (1 to 2 sec) dipped into an acetone bath at room temperature to remove adherent oil and then immediately transferred to liquid nitrogen where they remained until inserted into the helium bath (usually within an hour). The temperature of the aging bath was held constant to +3°C for longer aging times. The cryostat used for the measurement of superconducting properties consisted of outer and inner dewars for liquid nitrogen and liquid helium, Stokes 6-in. booster diffusion pump and Stokes Model 212 mechanical pump, temperature controller to measure and control the temperature of the helium bath, and a superconducting solenoid with inserted search coils to provide the magnetic field and measure the magnetic moment of the specimens. A schematic diagram of the cryostat is shown in Fig. 1. An ultimate temperature of 0.85°K was reached with this apparatus. The temperature controller used is similar to the one described by Blake and chase.' A 0.5 pct Allen-Bradley carbon resistor and a nichronle heater (200

Jan 1, 1968