Search Documents

By M. H. HARRINOTON

THE Transactions of the Institute afford abundant evidence of the general recognition by mining engineers of the importance of a safety-lamp which will not only give warning of the presence of fire-damp, but will also indicate the proportion in which it is present.' Mining-men are only too familiar with the frequent and sudden changes that constantly occur at the working-face of a gaseous mine. Nothing illustrates more forcibly the pregnant condition of the strata enfolding the seam and the seam itself, than the fact that a circulation of perhaps 150,000 cu. ft. of air may contain 2 or even 3 per cent. of marsh-gas, representing a volume of from 3,000 to 4,000 cu. ft. of this gas pouring-out each minute from the natural strata into the mine-workings. It would, indeed, be strange if this great outflow of gas were always constant, and it creates no surprise that such earth-breathings, as they may be called, are spasmodic and irregular in their wane and flow. There are other causes that act to vary the gaseous condition of mine-air. Gas has a tendency, often very manifest in mine-workings and airways, to stratify and, at times, to travel long distances in veins or streams. It is common to catch and lose the gas in the lamp when making a test. At times two lamps, held side by side in an air current, will indicate different gaseous conditions of the passing air. When testing for gas, the lamp may suddenly fill with flame, in a mine-chamber, where a moment before a careful test showed the presence of but 1 per cent. of gas. It is sometimes remarked that there is little need of detecting a smaller percentage of gas than is revealed by the common

Jan 1, 1906

By L. Weaver

THE Tennessee Copper Co.'s mines are in the southeast corner of the state of Tennessee, Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails.

Jan 1, 1950

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period Mar. 10, 1917, to Apr. 10, 1917. Frederick R. Ahbe, Athens, Pa. Frank M. Leland, San Francisco, Cal. J. L. W. Birkinbine, Philadelphia, Pa. Edwin Ludlow, Lansford, Pa. Samuel D. Bridge, Monterrey, Mex. E. P. Mathewson, Toronto, Canada. J. R. Buchanan, Pasadena, Cal. E. V. Matlack, Webster Grove, Mo. G. M. Colvocoresses, Humboldt, Ariz. E. C. Potter, Clearwater, Mont. F. G. Cottrell, Washington, D. C. R. B. Stanford, Bluefields, Nicaragua. H. N. Eavenson, Gary, W. Va. R. S. Ransom, Jr., Newark, N. J. H. T. Fisher, Englewood, N. J.. M. L. Requa, San Francisco, Cal. E. P. Fleming, Salt Lake City, Utah. John A. Rice, El Paso, Tex. F. L. Garrison, Philadelphia, Pa. W. E. Rice, Ringwood, N. J. W. M. Grant, So. Bethlehem, Pa. Lewis A. Riley, Philadelphia, Pa. J. F. Hanst, Negaunee, Mich. Hallet R. Robbins, Vancouver, B. C. H. D. Hibbard, Plainfield, N. J. Allen H. Rogers, Boston, Mass. B. B. Hood, Chrome, N. J. A. A. Stevenson, Philadelphia, Pa. Henry M. Howe, Bedford Hills, N. Y. Wm. Huff Wagner, Johnstown, Pa. Hennen Jennings, Washington, D. C. E. E. Watts, Denver, Colo. Oscar Lachmund, Greenwood, B. C. Samuel S. Wyer, Columbus, Ohio. H. W. Aldrich, after ten years of service with the Anaconda Copper Mining Co., at Anaconda, has resigned and accepted a position as general superintendent for the Ladysmith Smelting Works, at Ladysmith, B. C. Charles E. Bunker, formerly superintendent of the Keystone mine, has been appointed superintendent of the Bunker Hill mine near Amador City, Cal.

Jan 5, 1917

By Johnson Crawford, Alan H. Hoagland

Zinc mining at Jefferson City began in 1854 with small scale production of oxidized ore from open pits. Significant production began in 1913 with the development of the Mascot Mine by the American Zinc Company. In 1965, four flotation mills were treating crude ore at the rate of about 12,000 tons per day and the Mascot-Jefferson City district currently is the largest zinc producing area in the United States. The producing mines, Mascot, Young, North Friends Station, New Market Zinc, Grasselli, Davis-Bible, Coy, and the Jefferson City, are 15 to 28 miles northeast of Knoxville in the Valley and Ridge physiographic province, an area of gentle relief lying between the more rugged Great Smoky Mountains and the Cumberland escarpment. The ore is strata bound, occurring essentially within a stratigraphic range of 200 feet in the Lower Kingsport and Upper Longview formations of Lower Ordovician age. In the lower strata of the mineralized section, the ore generally is found in coarsely crystalline elastic dolomite breccia containing silica and chert debris within a sequence of aphanitic limestones. The upper strata of the mineralized section are fine-grained primary dolomites that, in the ore zones, have been fragmented in mosaic patterns by solution collapse with the interfragmental space filled by white gangue dolomite and sphalerite. The mineralogy is unusually simple, sphalerite being the only important sulfide. Pyrite is very sparse. Dolomite gangue is abundant, silica was deposited in quite small amounts, calcite is minor, and fluorite and barite are very rare. The principal ore controlling structures are rubble breccia zones that were formed during the post-Lower Ordovician-pre-Middle Ordovician erosion interval by supergene solution as a phase of the development of a regional karst system of underground drainage that extended to' depths of at least 800 feet. The major Appalachian orogenic structures are post-ore and have been superimposed on the ore bodies. There is substantial evidence to support the current thinking of the writers that the ore deposits were formed at a depth not exc1~eding 800 feet.

Jan 1, 1968

By R. N. Dokken, J. F. Elliott

A high-temperature solution calorimeter was used to measure directly the partial molar heat of mixing of nickel in the Cu-Ni system, 0 to 15 at. pct Ni and 1200°C; of silver in the Cu-Ag system, 0 to 50 at. pct Ag and 1100°C; and of cobalt in the Cu-Co system, 0 to 6 at. pct Co and 1200°C. The heats of fusion of copper and silver were also detervnined directly. The results of these investigations are as follows: Cu-Ni: HM = [2.64 + 0.25Xm JXNiXCy kcal/g-U~OI Cu-Ag: HM =[4.00 + 0.31XAglXAgXCu kcal/g-atom Cu-Co: HF~ = [8- 5X~,]X& kcal/g-atotn Cu, AH, = 3290 * 275 cal/g-atom Ag, AH, = 2890 * 250 cal/g-atom The performance of the calorimeter was enhanced by improving the operational and control procedures, particularly the temperature-wieasuren~ent method and the solute-addition practice. The interpretation of the experimental data was improved by developing machine computational techniques that increased the speed, flexibility, and accuracy of the treatment of the data. THIS paper reports further measurements of the heats of solution of liquid metals with the high-tem- perature solution ca1orimeter.l Measurements were made of the partial molar heats of mixing in the following liquid alloys: Cu-Ni, Cu-Ag, and Cu-Co. In addition the heats of fusion of copper and silver were also determined. The apparatus and the experimental procedure were essentially those of Benz and Elliott.2 Several modifications in the experimental method and the means for interpreting the data were incorporated in this study to improve the results. The operation of the calorimeter and its characteristics will be described only briefly here. The

Jan 1, 1965

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InSb, GaSb, and AlSb were measured over the temperature range 400" to 1450°K using a diphenyl ether drop calorimeter. Smoothed ualues of the thermal properties, H$ - H:9s, have been derived and are tabulated at even temperature intervals. The heats of fusion of the three compounds were determined as, respectively, 5707 *100, 7780 * 100, and 9800 5 3011 cal per g-atorn at the determined melting points of 797" l°, 985" * , and 1330" * 5°K. The calculated entropies of fusion are, respectively, 7.16 0.12, 7.90 * 0.11, and 7.37 * 0.23 cal per deg per g-atotn. The heat capacities increase substantially on tnelting in contrast to the behauior of structurally related germanium and silicon. Deriations from the Kopp-Neumann rule are negative for solid compounds and positive for the liquid phases. Previously obsevrrd "post melting" in InSb is confirmed. The high-temperature thermal properties of 111-V compounds are presently not well-established, despite the technical importance of these semiconducting cbmpounds. Uncertainties in available heats of fusion and heat contents have seriously hampered thermo-chemical evaluations' and thermodynamic analyses of phase equilibria2"" in these systems. This paper reports results of high-temperature heat content investigations of InSb, GaSb, and AlSb measured in the range 400" to 1450°K employing a diphenyl ether drop calorimeter. Similar measurements for InAs and GaAs will be reported in a following publication.~ EXPERIMENTAL PROCEDURES Samples. High-purity samples of the compounds InSb and GaSb were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories and in the form of single crystals by Dr. A. Strauss of the M.I.T. Lincoln Laboratory. Single-crystal samples of semiconductor-grade AlSb were supplied by Dr. W. P. Allred of the Bell and Howell Research Center. Chemical analyses indicated that all compounds were stoichiometric to *0.1 at. pct, which is within the experimental uncertainties of the analyses. Samples were crushed, weighed, and encapsulated in evacuated, thin-walled, fused silica capsules. The capsules were nearly identical in external shape, 2 cm by 2 cm diam, but varied in weight due to differences in wall thickness. One sample of AlSb was contained in a thin-walled, high-purity alumina cup encapsulated in silica and used for heat content determinations of liquid AlSb. The capsule materials showed no visual evidence of reaction with any of the compounds. The sample and capsule weights are given in Table I. Calorimeter. A Bunsen-type calorimeter, similar in design to a previously described instrument6 but employing diphenyl ether (C6H5)'0 as the calorimetric substance, was used for measurements of heat contents above 300.0°K, the melting point of diphenyl ether. Heat input to the calorimeter caused isothermal melting of diphenyl ether, and the resulting increase in volume was measured by displacement of mercury from the calorimeter into a 200 cm horizontal, calibrated capillary, 1.25 * 0.01 mm diam, or into a weighed beaker. The advantages of diphenyl ether over water have been previously pointed out7 and include: i) an increase by a factor of 3.5 in sensitivity as measured by the ratio of the volume change to the enthalpy change on fusion, ii) the smaller required extrapolation from the melting point to the standard temperature of 298.17"K, and iii) the positive volume change on fusion of diphenyl ether in contrast to the contraction which occurs on fusion of ice. Diphenyl ether was purified by fractional crystallization to 99.95 mol pct as determined from the melting point depression with fraction crystallized. During assembly of the calorimeter, the ether was repeatedly outgassed under high vacuum to remove dissolved air. The calorimeter receiving vessel consisted of an 8-in.-long by 1:-in.-diam copper tube with twelve horizontal 3-in.-diam radiator "fins" for dissipating heat to the surrounding mantle of diphenyl ether. Before forming the mantle the chamber surrounding the receiving vessel contained 3300 cu cm of liquid diphenyl ether above 250 cu cm of mercury which was

Jan 1, 1970

By Joseph Hyde Pratt, Douglas B. Sterrett, CHAPEL HILL

I. DESCRIPTION. MONAZITE is one of the minerals which, for a long time, was considered rather rare in its occurrence, but, upon a commercial demand arising for it, prospectors and engineers soon located large deposits of it in the Carolinas and Brazil, and the supply has always been able to meet the demand. During 1908 further sources of supply of monazite have been discovered and developed in Idaho. North and South Carolina, however, are the only States that have thus far put any monazite on the market. Monazite is essentially an anhydrous phosphate of the rare-earth metals, cerium, lanthanum, and didymium (Ce, La, Di)PO;. There is nearly always present a varying but small percentage of thoria, ThO2, and silicic acid, SiO, which are very probably united in the form of a thorium silicate, ThSiO4 Some monazites contain but a fraction of a per cent. of thoria, while others have been recorded that showed the presence of from 18 to 32 per cent. ; but the majority contain from 3 to 9 per cent. of this oxide. It is the presence of the thorium oxide that gives the monazite its commercial value. The analysis occasionally shows also the presence of other constituents, as the yttrium and erbium oxides, zirconia, alumina, magnesia, lime, iron oxides, manganese oxide, and titanium oxide. Monazite is light-yellow, honey-yellow, reddish-, brownish-, or greenish-yellow in color, with a resinous to vitreous luster, and is translucent to subtransparent. It is brittle, with a conchoidal to uneven fracture, and is from 5 to 5.5 in hardness, and from 4.64 to 5.3 in specific gravity. It crystallizes in the monoclinic system, and some crystals have been observed that were 6 in. in length. The more perfect crystals are, however,

Jun 1, 1909

By S. J. Hruska

Rate expressions for the formation of two-and three-dimensional nuclei on foreign substrates are developed, taking into account previously neglected contributions to the standard Gibbs free energy of formation of critical nuclei. The temperature dependence of critical super saturation data predicted using these expressions is in accord with data for cadmium on copper and sodium on CsCl. EXPERIMENTAL data on the heterogeneous nuclea-tion of metal crystals from the vapor phase1&apos;2 exhibit the temperature dependence predicted by a nucleation rate equation derived by Pound et al.3 In their treatment, the critical nuclei are visualized according to the Volmer4 model as cap-shaped (three-dimensional). Accordingly, it seems desirable to compare these data with a nucleation rate equation which is derived on the assumption of disk-shaped (two dimensional) nuclei. Further, Lothe and Pound5 have recently shown that the standard Gibbs free energy of formation of these critical nuclei contains a contribution which has heretofore been neglected. Thus it is necessary to re-examine these nucleation data using a rate equation which contains this contribution. The van&apos;t Hoff isotherm relates n(i), the concentration of nuclei of critical size i (i = number of atoms), to nil), the concentration of adsorbed single atoms: where standard Gibbs free energy of formation of critical nuclei given by is temperature insensitive and is the bulk free energy change/volume of transformed material], T = substrate temperature and k = Boltzmann&apos;s constant. Previously,3 was determined by considering only the contributions of bulk and surface free energies in transforming i atoms from the population nil) to a cluster of i atoms. It has been shown5 that this procedure does not take into account the free energy contribution arising from the multiplicity of sites, q, where the clusters can be situated. If this contribution, -kT In q/n(l),is added to iG3 [Note that this increases n(i) by a factor q/n(l).] Since the above does not affect the remaining terms in the rate expression of Pound et al., the details are referred to their paper. The resulting nucleation rate is If the experimental AGV and T values at some common value of are employed, a plot of vs T(ln C3/l + In p&apos;) should yield a straight line of slope k/B<p and intercept . The corresponding plots for / = 1 nucleus per sq cm sec and C3 = 1018 are shown in Figs. 1 and 2 for cadmium on copper1 and sodium on CsCl2 and the values of obtained therefrom are entered in Table I. It is apparent that the data yield reasonable straight lines with about the same scatter as found using the equation of Pound et al. When the configuration of minimum free energy for a nucleus is a circular monatomic layer, the standard free energy of formation is

Jan 1, 1963

By W. A. Backofen

THE texture of cold-drawn copper wire has been described most often as a composite of [Ill] and [loo] directions aligned parallel to the wire axis.&apos; Hibbard2 suggested that sufficient reduction will result in a single [111] texture and reported that after a reduction in area of 96.4 pct, such a texture was nearly obtained. Other work3-4 has shown that recrystallization within the temperature range of 300" to 1000°C does not alter the texture established by cold-drawing. In general, however, the texture of cold-drawn end annealed copper wire is not as well defined as the deformation texture. In the work reported here it was found that the double-fiber, deformation texture persists even after a reduction in area of 97.3 pct, and after recrystallization the texture is practically all [l00]. The wire used in this work was prepared in the following way. A 3/4-in. diam length of annealed OFHC copper was cold-drawn to a diameter of 1/8 in., a reduction in area of 97.3 pct. Each step in the drawing operation brought about a reduction in area that varied from 6 to 10 pct. Short lengths of this wire were etched in a 50-pct solution of nitric acid to a diameter of approximately 0.01 in. The texture of the cold-drawn specimens was determined with the conventional X-ray transmission diffraction technique using filtered copper radiation. The X-ray beam was directed perpendicularly to the wire axis and the diffraction rings were recorded on a flat film. Fig. la is typical of the photo-grams obtained and reveals that the cold-drawing schedule described above introduces a distinct, double-fiber texture with both [Ill] and [l00] directions aligned parallel to the wire axis. Supplementary measurements with a Geiger-Mueller counter of the intensity of reflection from (111) planes showed that the [111] component was much more predominant than the [l00]. Additional specimens of the drawn and etched wire were annealed in a salt bath at temperatures from 300" to 450°C. The texture of the recrystal-lized wire was studied with the same technique applied to the cold-drawn wire. Fig. lb is an X-ray photogram of a specimen annealed for 1 ½ at 300°C and is typical of those obtained from re-crystallized specimens. The photogram shows that recrystallization of this material is accompanied by the almost complete elimination of the [111] component of the deformation texture. A pronounced strengthening of the [100] component was evident from intensity measurements with a Geiger-Mueller counter. In summary, the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [Ill] and [loo] directions aligned parallel to the wire axis. Recrystallization of such wire at temperatures from 300" to 450°C introduces a texture which consists almost entirely of a [loo] alignment. Acknowledgment Sidney Rolle of the Scomet Engineering Co. generously supplied the OFHC copper used in this work. References &apos;C. S. Barrett: Structure of Metals. p. 382 (1943) New York. McGraw-Hill Book Co. 2 W. R. Hibbard, Jr.: Trans. AIME (1949) -185, p. 598; Journal of Metals (Sept. 1949) TN 19E. 3 P. 422 of ref. 1. &apos;E. Schmid and G. Wasserman: Ztsch. Physik (1926) 40, p. 451.

Jan 1, 1952

By K. G. Davis, P. Fryzuk

A study has been made of the effect of undercooling on the grain structure and solute distribution in small ingots of pure bismuth and of a 100 ppm Ag in bismuth alloy. Autoradiographic evidence shows that in undercooled melts a network of dendrites is formed throughout the melt immediately after nu-cleation. At large undercoolings the dendrites are very thin and closely spaced. The origin of the observed grain morphology can be explained on the basis of information about the mode of solidification revealed by the impurity substructure. WHILE a great number of studies of nucleation in undercooled molten metals have been made, comparatively little attention has been given to the mode of solidification from melts with large undercool- ings. Colligan and Bayles1 and Walker2 have measured the rate of advance of the solid-liquid interface in undercooled nickel melts, but the morphology of the solidifying material remained a matter of speculation. Fehling and Scheil3 have described the grain structure in ingots formed from undercooled melts of nickel, palladium, and copper, and a series of Ni-Cu and Ni-Pd alloys. At small undercoolings, equiaxed structures are observed, the grain diameter tending to increase as the temperature of nucleation is lowered. At greater undercoolings, a columnar structure is developed, while with still further undercooling there is a smaller grain size incorporating rather coarse subgrains. All-bright and Colligan4 examined the grain structure shown by ingots solidified from melts of nickel and of Ni-Ag alloy at an undercooling of 105°C, and concluded that considerable grain growth had taken place after solidification. The object of the present work is to correlate the mode of solidification from undercooled melts with both the grain structure and impurity segregation, using tracers to examine the latter.

Jan 1, 1965

By M. W. BERNEWITZ

IT is 27 years since I last visited Broken Hill, New South Wales, one of the world&apos;s greatest lead-silver-zinc districts. Then, the flota¬tion of ores was in its infancy. The Minerals Separation process had its birth as a practicability in the Central Mill, which is still operating and yielding high recoveries. The average Australian knows that Broken Hill is an important mining center in a "corner" of New South Wales, but he does not know what a factor it is in the lead, silver, and zinc production of the world. Nor does he realize that among the ramifications arising from metal production at Broken Hill are the great lead smelter at Port Pirie, South Australia, 254 miles southeast; the electrolytic zinc works at Risdon, and the limestone mine at Davenport, Tasmania; the acid works at Cockle Creek, New

Jan 1, 1935

By George W. Maynard

(Pittsburg Meeting, March, 1910.) AT the Pittsburg meeting of the Institute, May, 1879, I made the first announcement in America of the results obtained by Sidney Gilchrist Thomas and Percy C. Gilchrist, ill their efforts to eliminate phosphorus in the manufacture of steel in the Bessemer converter and the open-hearth furnace.1 The first published statement in an American newspaper was a reprint of the first Thomas-Gilchrist paper, 2 which I sent to J. C. Bayles, at that time the editor. At the suggestion of many friends who were present at the Pittsburg meeting, and others who are cognizant of the beginnings of the process in the United States, and for the information of the younger generation of the iron and steel fraternity, I have thought it eminently proper that the history of the process in detail should be given where I made the first announcement and where the process has had its largest development. During my residence in England, from April, 1873, to February, 1879, and as a member of the Iron and Steel Institute since 1874, I was present at many of its meetings during those years. At nearly -every meeting the burden of discussion was the question of the use of pig-iron containing phosphorus in the. manufacture of steel by the Bessemer or the open-hearth process. In my biographical notice of Thomas;3 read at the New York meeting of, the Institute, February, 1885, I show that the working-out of the process was not a hap-hazard or accidental inspiration, but the culmination of many years of investigation of experiments and theories which had been carried on and advanced by chemists and metallurgists at home and abroad. 1 Trans., viii., .5 (1879-80). 2 The Iron Age, vol. 22, No. 17, p. 3 (Oct. 24, 1878). 3 Trans.. xiii., 785 to 791.

Jul 1, 1910

By CHARLERS R. FETTEE

A slight decrease in drilling activity occurred in the oil fields of western Pennsylvania during 1945 and a considerable decrease in the shallow-gas territory (Upper Devonian or higher). The number of deep tests (Middle Devonian or deeper) completed was two less than in 1944 and these did not open any new reserves of natural gas. Thus far, no commercial oil has been encountered in sands below the Upper Devonian in Pennsylvania. Oil production declined 8 per cent.

Jan 1, 1946

By A. L. Holley

THIS process is performed in the Pernot puddling furnace; it removes from 75 to 80 per cent. of the phosphorus, most of the sulphur, and practically all the silicon, from crude iron, in from five to eight minutes. It has been in regular use since March, 1877, and has prod uced over seventeen thousand tons of washed metal for the open-hearth furnace. During two years, nearly all, and lately, all the open-hearth steel produced in these works has been made from about 5 tons of washed pig and 2 tons of scrap per open-hearth furnace heat. There are 12 open-hearth furnaces, of which 4 to 9 are running, according to the state of orders. A large amount of highly phosphoric iron from France and Belgium has been also washed and then puddled for parties who have taken, or are expected to take, licenses. The washing of pig for puddling, however, is not a practice at Krupp&apos;s works, because pure pigs are nearly as cheap as impure ones. The author and his assistant, Mr. Laureau, spent, during the last month, three days at Krupp&apos;s works, examining this process. They copied out of the office books characteristic analyses and physical tests, some of which are given herewith. They also brought hone many samples of pig, cleaned metal, puddle bar, and steel, which they saw treated. Analyses of some of these samples appear in Table IV. As there are no blast furnaces at Essen, the iron is melted in two Bessemer cupolas with fore-hearths; they melt 12g pounds of iron with 1 pound of coke. The metal is run by a spout from the fore-hearth into an opening at the side of the main door of the washing-furnace. The Washing furnace.-This is a regenerative gas furnace. It has a Pernot revolving-hearth of 12 feet external diameter and 3 feet depth. (See Plate.) The four regenerator chambers have 780 cubic feet capacity, which is about the same as the average regenerator capacity of open-hearth steel furnaces of equal tonnage. The lining is 13 inches thick on the sides and 9 inches on the bottom, thus giving a hearth 9 feet 10 inches by 2 feet 3 inches deep. The lining is composed of lumps of highly refractory ores

Jan 1, 1880

By H. H. Campbell

MANY attempts have been made to write a formula by which to calculate the strength of steel from its chemical composition, but most of these endeavors have failed because there were too many disturbing conditions. It is idle to collect from the pages of trade-papers, books, or the proceedings of scientific societies, a multitude of observations. The combination of such results will simply show that steel of the same composition will vary in tensile strength through wide limits-a fact that has been known for generations. That cold-working, overheating, and many another form of heat-treatment alter fundamentally the strength of steel, is ancient history, although it is only recently that the microscope has pointed out the road to an explanation of the phenomena. It may be urged that the microscopic structure must be taken into consideration in any formula giving the ultimate strength, but from the standpoint of the present investigation this is unnecessary. We are trying to determine primarily, not what changes in ultimate strength may be made by variations in the condition of carbon, but what effect is produced by changes in the amount of carbon, when its condition remains constant. For such an inquiry, in order that the condition of the carbon should remain as nearly uniform as possible, it is essential that all test-pieces be made under the same conditions; and it is be¬lieved that the tests described in this paper satisfy that require¬ment. The investigations were made at the works of the Pennsylvania Steel Company,. Steelton, Pa.; the ingots from which the tests were made were 6 in. square in every case; they were heated in the same furnace and forged at the same ham

Jan 1, 1905

By C. W. Davis

THE name fuller&apos;s earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller&apos;s earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water -by acid which are equal to or more efficient than an untreated fuller&apos;s earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller&apos;s earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller&apos;s earth and other, adsorbent earths.

Jan 1, 1929

By Bobby P. Faulkner

The Tennessee Copper Co.&apos;s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966

By R. J. Woody

Design of the most economic continuous counter-current decantation (CCD) circuit is based on selection of the number of stages and the wash volume that will give the minimum summation of the following items: 1) Capital and operating costs of the CCD circuit. 2) Capital and operating costs of the precipitation circuit. 3) Value of the dissolved product lost.

Jan 1, 1959

By M. C. LAKE

THE industrial development of the United States has been stimulated by the presence of high-grade iron ore in the Lake Superior district. These great deposits have been susceptible to economical extraction and are conveniently located for cheap lake vessel transportation to the great consuming centers. The district furnishes from 80 to 85 per cent of the iron ore annually consumed in the United States, and a full understanding of the available supply of this great commodity is so important that it is well to consider whether or not the industrial supremacy and national independence attained as a result of the abundance of cheap ore are permanent. The enormous deposits of high-grade ore available in the Lake Superior district have been the foundation upon which the vast industrial structure of the steel and allied industries has been built. It is extremely important to the country as a whole, and especially to those States and communities now dependent on Lake Superior ore for their prosperity, that their industries shall retain the particular advantages with which they are now endowed, and that a generous supply of high-grade raw material be available for their consumption at a satisfactory cost. The steel industry is so basic and fundamental that any fluctuation in the cost of its finished products as determined by the supply and cost of the raw materials involved in its manufacture will necessarily affect the business of a wide variety of industries which are dependent on it.

Jan 1, 1926

By C. W. Davis

THE name fuller&apos;s earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller&apos;s earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water by acid which are equal to or more efficient than an untreated fuller&apos;s earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller&apos;s earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller&apos;s earth and other adsorbent earths.

Jan 1, 1929