Search Documents

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By Daniel Wild, Tobias Scheffer, Marvin Laugwitz, Martin Jochum

Leveling is a standard process in the rolling mill to eliminate flatness deviations. The process layout is based on models and the leveling result depends on the accuracy of the material parameters in these models. Even small deviations from the correct assumptions can have a major effect on the final flatness. Thus, after leveling the products may look optically flat, but subsequent to a final cutting process springback occurs due to residual stresses. The objective of this work is to analyze the influence of material parameters and gravity on the flatness after leveling. To evaluate the sensitivity of the process, an FE parameter study is exerted that reveals the influence of fluctuations in material properties in the case that the leveling setup is fixed. Gravity is neglected to not conceal flatness deviations. Examples of this study are rerun in a further step under consideration of gravity to also analyze its influence on the resulting flatness and residual stresses. Finally, to analyze the consequence of the residual stresses, all information of the plate from the previous step are transferred while gravity is suppressed to prompt springback. This study revealed that slight deviations of the material properties can lead to uneven plates in simulations where gravity is not considered. If gravity is taken into account, the unevenness is concealed and the plate seems flat. A springback simulation of the same plate shows that strong residual stresses are still present and would lead to unevenness if e.g. the plate were cut.

Oct 1, 2019

By Pedro Jorge Walburga Keglevich de Buzin

The steel production in mini mills generates several process residues, among them the electric arc furnace dust (EAFD). This residue has as main elements Fe, O, and Zn, being classified as hazardous by the presence of Pb and Cd. In recent years, a rise in the chlorine content of this residue was observed, motivated by the increased use of scrap with impurities bearing this element. In this work, a qualitative assessment of the presence of chlorine in the electric steelmaking process is made. Complementing it, theoretical considerations based on the computational thermodynamics tool FactSage show the effects of the chlorine on the mineral species in EAFD and on gaseous species in the gas phase (HCl and Cl2). For this study, PVC polymer was used as the chlorine carrier substance which contaminates the EAF charge; presence of other minor elements in the system such as K, Na and Pb were also considered.

Aug 7, 2018

By Kazuya Nakabo

In this article, influences of restraint and MgO content on densification of alumina-magnesia castable during heating were experimentally studied. High thermal expansion-alumina-magnesia castable specimens were surrounded by low thermal expansion-alumina-silica castables, and heated in an electric furnace. Doing so allows restrained heating of alumina-magnesia castable. According to the results of simple calculations, the restraint stresses were estimated to be between 2 to 20 MPa, so the experimental conditions were considered reasonable. As a result of the experiments, it was verified that restraint densifies alumina-magnesia castable, resulting in an increase in modulus of rupture and modulus of elasticity. The densification effect of restraint became larger as the MgO content increased. The effects are attributable to an in-situ spinel forming reaction, which improves corrosion resistance.Taking the temperature distribution in the castable lining into account, large restraint stress is expected for the hot face while only a little effect is expected for back end. Thus, excessive difference in material property in the thickness direction, which is undesirable in terms of structural spalling, is a concern.Hence, the MgO content of alumina-magnesia castable should be determined carefully, taking not only corrosion resistance but also spalling resistance into consideration.

Oct 30, 2017

By Haruki Inami, Takashi Ishida, Kazuhiro Ohara, Hiroyuki Imanari

The highly competitive business environment of the international metals industry is driving demand for more cost-effective operation of steel making facilities, rolling mills, and strip processing lines. Achieving stable operation is vital if the steel industry is to produce high-quality products constantly and productively. In recent years, advances in computer processing speeds, data acquisition rates, and data storage capacity have rapidly led to greater use of the new technologies of big data, analytics, the IoT, and AI by control system designers and process engineers, and the introduction of industrial applications. The “Smart Rolling Mill” solutions for hot strip mills have been developed by our group with the goal of achieving sophisticated, state of the art, and automated operation in steel rolling mills. The various solution engines improve process stability, increase the performance of mill equipment, and provide improved process control. These solution engines are based on extensive knowledge of the rolling process and the associated control systems. Two solution engines in particular are the diagnosis systems for rolling condition and for product quality that contribute to cost-effective operation and lower yield loss. This paper focuses on the diagnosis systems for rolling condition and for product quality in hot strip mills. Advanced information technologies using big data analytics and machine learning are applied to real-time data collected from the automation system that controls operation and the rolling process. We have developed diagnosis solutions for rolling condition and product quality utilizing predictive and clustering diagnosis. Predictive diagnosis prevents serious problems by detecting changes in the state of the plant or in the rolling condition. Clustering diagnosis classifies patterns of fluctuation in product quality trend charts, providing effective tuning guidance for improving product quality. This paper describes these applications with several examples.

Oct 1, 2019

By Wolfgang Oberaigner

Primetals Technologies has always been a driver of innovation in steelmaking, especially by providing sophisticated process expert models for continuous casting machines. This capability is demonstrated by recent advancements in automation solutions that include: DynaPhase, Dynacs 3D, and DynaGap. This state-of-the-art suite of dynamic secondary cooling and soft-reduction packages take into account thermodynamic effects such as shrinkage and phase transitions, and thereby significantly contribute to direct quality improvements during the solidification phase in the continuous casting process. Speed Expert calculates an optimum casting speed for every casting situation, and additionally recommends a strand speed so that the point of final solidification is positioned at the end of a segment for optimum soft reduction. In the case of steel grade changes, the Intermix Expert precisely calculates the chemical properties of the mixed steel, thereby minimizing losses due to deviations from required specifications. The Nozzle Expert is a new model that detects clogged nozzles and broken hoses in secondary cooling systems. The first installations were highly successful and customers are pleased with impressive reductions in maintenance costs and improved steel quality. This paper describes these innovative process automation solutions and gives an overview about the successful results achieved within the first installations.

Aug 16, 2017

By Breno Totti Maia

This work was a continuous and multidisciplinary development. Through studies of the blowing process and its parameters results, evolutions, improvements and adjustments were made on the lance’s hot face with Slagless® technology, as well in the process parameters and mitigating actions of the projection of materials out of the converter. The main results are the increase in the nozzle’s life with a “record mark” of 1785 heats, and water leakage occurrence in the cartridge decreased considerably reaching the mark of one year without any occurrence.

Oct 30, 2017

By Christoph Aichinger

The optimization and improvement of a modern integral iron and steel works gets more and more difficult as each individual plant is already operated at its best efficiency and at the lowest operational expenditures. However very often the individual plants are considered as stand-alone units and there are losses and inconsistencies on interfaces and take over points, which could be avoided and by that improving the overall performance of the iron and steel works as a holistic unit. Primetals Technologies looked into this subject extensively in the recent years and is now ready to offer new tools and services in order to assist operators to find further potential for improvement in processes, which seem to be fully developed at first sight.

Aug 17, 2017

By Nathanael Wagner Sales Morais

Os aços maraging tem grande importância tecnológica devido sua aplicação nas industrias aeroespacial e nuclear. Uma das aplicações para esse material é a fabricação de cilindros de alta resistência pelo processo de estampagem profunda, logo o conhecimento da textura cristalográfica torna-se fundamental. Este trabalho investigou o efeito da laminação à frio seguida por um recozimento sobre a microestrutura, textura e anisotropia plástica no aço maraging 350. A anisotropia foi medida pelo cálculo dos coeficientes de Lankford e dos coeficientes de anisotropia normal (Rm) e planar (?R). Os resultados mostraram o aumento na deformação a frio gera um aumento na intensidade da fibra acompanhada de um aumento no valor de Rm. As análises metalográficas mostram que maiores reduções induzem à um precipitação intermetálica após o recozimento.

Aug 8, 2018

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018

By Massimilinao Svetina

In 2010 Danieli & C. S.p.A. put into operation a new Pickling Tandem Mill in Cremona (Italy) at Acciaieria Arvedi, the last Pickling line coupled Tandem Cold Mill (PLTCM) in Europe. The plant was tailor-made to suit the specific requirements of this customer; a very broad range of sizes and grades (IF to AHSS as well as DP and TRIP1000) including ultra-thin hot band can be processed, achieving a total capacity of 1.6 Mt/y. The Danieli & C. S.p.A. Turboflo® process was selected because of its proven efficiency and ability to handle ultra-thin gauges at speeds exceeding 400 mpm in the pickling tanks. All the equipment, i.e. pickling section and rolling mills was provided with the last generation of Danieli market-oriented technologies. Danieli & C. S.p.A. - with the support of Arvedi and feedback from the field - is continuously improving its technical design solutions and optimizing plant operations.

Aug 16, 2017

By Bianca Proença

Fotocatalisadores de nióbio foram obtidos por anodização a 15 V, utilizando uma solução de K2HPO4 10% p/p em glicerol anidro como eletrólito por 15 minutos. As amostras foram caracterizadas por difração de raios-X para avaliação da estrutura cristalina obtida. A fotodegradação do glicerol (utilizado como agente de sacrifício) foi avaliada pela técnica de cromatografia líquida de alta eficiência.

Aug 16, 2017

By Flávia Tereza dos Santos Fernandes Tolomelli

Este trabalho teve como objetivo estimar as temperaturas de transformação de fases por meio de termodinâmica computacional (A1 e A3), dilatometria (Ac1 e Ac3) e monitoramento do resfriamento ao ar após passes de laminação a quente em escala piloto (Ar3 e Ar1). Objetiva ainda descrever a evolução microestrutural da austenita em um aço baixo C microligado ao Nb onde se almeja a produção de um aço ferrítico-bainítico, coletando-se amostras após cada passe de laminação através do congelamento da microestrutura por intermédio de resfriamento em salmoura com o objetivo adicional de verificar a ocorrência de recristalização entre passes.

Jul 30, 2018

By Caroline Antunes Correa

Durante o processo por estampagem incremental, parâmetros como velocidade relativa, tamanho e material da ferramenta de estampagem, podem mudar as características superficiais do material. Para um biomaterial ser utilizado em implantes, um dos principais aspectos que pode influenciar sobre o processo de osseointegração são propriedades superficiais como rugosidade e molhabilidade. Nesse contexto, esse trabalho visa avaliar o efeito do processo de estampagem incremental seguido pelo tratamento térmico sobre a rugosidade e molhabilidade de chapas de Ti-cp com estampagem. A composição química e a morfologia das superfícies foram avaliadas por MEV/EDS. Resultados preliminares indicaram que a morfologia superficial é fortemente modificada pelo processo de estampagem incremental.

Aug 16, 2017

By Noan Tonini SImonassi

A utilização de compósitos de matriz polimérica reforçados com fibras naturais vem assumindo um papel importante no âmbito da engenharia de materiais. O baixo custo, a biodegradabilidade e a redução do peso especifico torna a utilização desse tipo de compósito bastante atrativa. O objetivo deste trabalho é avaliar o desempenho da fibra de sisal como reforço do policarbonato visando uso utilização militar, especialmente em proteção balística. Antes da confecção dos corpos de prova, foi realizada a redução no tamanho de partícula do policarbonato e da fibra de sisal através de um moinho de facas, posteriormente dos corpos foram submetidos aos ensaios de tração e flexão.

Oct 30, 2017

By Márcio de Morais Tavares

A espectrometria de fluorescência de raios X (FRX ou XRF) é uma das técnicas analíticas mais utilizadas em geoquímica. Na indústria mineral também se utiliza a espectrometria de absorção atômica (AA). A comparação de concentrações de sílica e alumina de oito amostras padronizadas de minério de ferro obtidas a partir das técnicas FRX e absorção atômica, constitui o objetivo deste trabalho. Foram realizadas análises dos mesmos padrões em outros dois laboratórios para reprodutibilidade dos resultados. Foram utilizados um espectrômetro FRX e um espectrômetro de absorção atômica para realização dos ensaios. As análises produziram resultados satisfatórios, com desvios médios de 0,502 para a sílica e 0,096 para a alumina.

Aug 16, 2017

Este trabalho teve como objetivo estudar as possíveis transformações microestruturais ocorridas em um aço de alta dureza submetido a altas taxas de deformação induzida por impacto balístico de um projetil 7,62x51 mm perfurante (Pf). Este aço, produzido por siderúrgicas nacionais, compõe o quadro de materiais nacionais usados como blindagens para proteção veicular. Após o ensaio balístico, a microestrutura do material “como recebido” e da região adjacente ao impacto, foi analisada por meio de microscopia eletrônica de varredura. Os resultados comprovaram o surgimento da microestrutura conhecida por banda de cisalhamento adiabático nos impactos que produziram perfuração, ou seja, penetração completa do projetil, de acordo com o critério da Marinha.

Oct 30, 2017

By Douglas Will Leite

O objetivo deste estudo é recuperar parte do alumínio empregado na fabricação das embalagens de medicamentos do tipo “blister”, por tratamento químico e térmico seguido de separação gravimétrica, resultando na obtenção de alumínio na forma de óxido (Al2O3). A caracterização do produto particulado metálico obtido constitui-se em um caminho para se chegar ao patamar de existência de coleta seletiva após seu descarte, diminuição deste tipo de embalagens nos aterros sanitários e/ou incineradores de lixo doméstico e posterior reaproveitamento com amplos benefícios ambientais. A caracterização morfológica do óxido de alumínio obtido foi realizada utilizando as técnicas instrumentais de ICP/AES e MEV/EDS.

Aug 7, 2018

By Diego Santana Torga

É comum encontrar sintonia de controladores PID que não levam em consideração o sinal de controle aplicado a variável manipulada. Portanto, variações rápidas e amplitudes elevadas podem ser geradas, que, na prática, pode ser inviáveis, devido à limitação física de atuadores e equipamentos industriais. Nesse artigo é desenvolvido um método de sintonia em que os parâmetros do PID são calculados por meio do Algoritmo Genético. A função de custo proposta penaliza tanto a amplitude do erro de controle quanto à variação da variável manipulada. A estabilidade é garantida com as restrições de robustez sobre o pico das funções sensibilidades. Exemplos simulados demonstram as vantagens da sintonia proposta.

Oct 30, 2017