Search Documents

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion- resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Feb 24, 1997

By J. Yue

"Mount Milligan mine is located in northern British Columbia. The concentrator employs conventional SABC grinding circuit with bulk sulphide flotation processes. Commissioning started in September of 2013 and nameplate production of 60,000 TPD was reached in the fourth quarter of 2015. As is typical with many mill ramp ups, bottlenecks developed as throughput increased. Since then, plant modifications and new control philosophies in the comminution and flotation circuits have been implemented and evaluated. The mine-to-mill collaboration played a key role in reaching target throughput rates by improving blast fragmentation and implementing temporary pre-crushing. Results of the projects as well as ongoing challenges/bottlenecks and solutions will be discussed.IntroductionMount Milligan Mine is a copper-gold producer located approximately 253 km northwest of Prince George in British Columbia. Production commenced in September 2013 and reached nameplate capacity of 60,000 TPD in December 2015. Average head grades for the mine life average 0.18% Cu and 0.39 g/t Au.Circuit DesignOriginal process design began with run-of-mine ore from the pit crushed through a 60-110 gyratory crusher, conveyed to a live ore stockpile and fed to the mill via four variable apron feeders. The concentrator circuit employs SAG mill - Ball mill - Pebble Crusher (SABC) grinding configuration to grind the ore down to a target P80 of ~200µm. It is then fed to two parallel trains of flotation tanks, each consisting of five 200 m3 tank cells with the first two being roughers and last three being scavengers. Concentrate streams from roughers and scavengers are separately reground with a closed circuit Tower mill and two open circuit ISA mills operating in parallel, respectively.Three stages of cleaners upgrade roughers/scavenger products to 25% Cu followed by a cleaner scavenger stage. The final concentrate is then thickened and filtered to approximately 9% moisture and shipped off site (Figure 1)."

Jan 1, 2017

By Rocky (Yaokun) Wu

This paper introduces the development and application of a new cable anchor - Cable-Lok for pre-stressed cable bolting in mines. Cable-Lok is a spring-loaded cable anchor suitable for the drill hole diameter of 50 and 65 mm (2" and 2.5") in medium soft rock to hard rocks. The cable anchor is automatically set on installation and the cable can be tensioned immediately to provide active and primary support throughout its length. Post-grouting can be conducted independently. In comparison with the conventional cable bolting, Cable-Lok anchor will greatly speed-up the cable bolting circle and decreases the cost of cable bolting. Cable bolting anchored with Cable-Lok anchor has wide application in mines, e.g. pre-stressed cable bolting in large span drifts and intersections for permanent rock support, or in hanging walls or stopes for temporary support, or cable lace anchoring etc. This paper introduces the principle of pre-stressed cable bolting and the specifications of the Cable-Lok anchor, presented the testing results in laboratory and the application cases in mines.

Oct 1, 2010

By D. T. G. Emmett

[ ] South Africa, by a wide margin, is blessed with the largest known world reserves of platinum. The optimal use of these resources for the benefit of all South Africa?s peoples is a goal shared by industry, government and all South Africans. The challenge is to grow the industry in accordance with demand growth and thus to manage a long-term stable growth pattern for PGM usage world-wide. Amplats and the South African producers are well able to meet this challenge [ ] South Africa plays a critical role in the provision of Platinum Group Metals for world markets. In fact no other country has the productive capacity nor the geological reserves to supply the world?s platinum needs. The world required some 5 million ounces of Platinum in 1997 and South Africa supplied a full 74% thereof. The second major supplier, Russia provided a further 18% of world demand, primarily as a by-product of nickel production. Amplats satisfied about 37% of total world demand followed by Impala 20% and Lonhro at 12%.

Jan 1, 1998

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By Edward A. Barrett, Kathleen M. Kowalski-Trakofler

This paper discusses the application of a training intervention that uses degraded images for improving the hazard recognition skills of miners. Method: NIOSH researchers, in an extensive literature review, identified fundamental psychological principles on perception that may be employed to enhance the ability of miners to recognize and respond to hazards in their dangerous work environment. Three studies were conducted to evaluate the effectiveness of the degraded image training intervention. A model of hazard recognition was developed to guide the study. Results: In the first study, miners from Pennsylvania, West Virginia and Alabama, who were taught with the aid of degraded images, scored significantly better on follow—up hazard recognition performance measures than those trained using traditional instructional methodologies. The second and third studies investigated the effectiveness of the training intervention at two mining companies. Data collected over a3—year period showed that lost—time injuries at mines in Alabama and Illinois declined soon after the training intervention was instituted. Impact on Industry: Further exploration of the hazard recognition model and the development of other interventions based on the model could support the validity of the steps in the hazard recognition model.

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

Cobalt mostly occurs as a minor, but valuable, constituent in most nickel and a few copper ores, however it is not generally found alone in commercially viable deposits. Its concentration and extraction are therefore intimately linked to the recovery of the primary metals and the major task for the metallurgist is to extract cobalt of commercial grade from a much larger mass of either nickel or copper and sometimes both. With a particular focus on Vale Inco?s operations, this paper provides a brief overview of the mineralogy of the main deposits being currently exploited that contain cobalt as a co or by-product. The concentration and then extraction to metal are reviewed and some advances released into the public domain are discussed.

May 1, 2009

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

Fire suppression systems are now recognised by both NFPA 502 and PIARC as legitimate tools for both life protection and asset protection. The effectiveness of these tools for life protection demands extremely rapid and accurate incident detection coupled with rapid response. This rapid response must be integrated with other emergency systems such as emergency ventilation. The March 2007 fatal Burnley Tunnel incident in Australia graphically illustrates the potential of effectively integrated fixed suppression systems to protect people from harm and save infrastructure from damage. Despite the raft of technology available in that instance to the operator it was the human operatorÆs ability to effectively control the emergency equipment and not the equipment itself which so positively influenced the threat to life and property.

Jan 1, 2008

The method of investigation was to study the distribution of ore in great detail, to make a thorough structural study of the lode and the mine area, and then to compare the results of the two studies. Such a comparison usually reveals a very close relationship between geological structure and ore distribution, and can often lead to important conclusions which would not be reached in the ordinary working of a mine.The Triton mine lies 30 miles E.N.E. of Cue, or 380 miles N.W. of Kalgoorlie, in typical pre-Cambrian rocks, consisting of gTeenstone lavas and tuft's, interbedded with slates and some sediments, and intruded by granite and porphyry. Fig. 1 (at end of paper) is a longitudinal section of the mine and shows that the workings consist of the main North Emu and the smaller South Emu, separated by a distance of about 1 of a mile. Both orebodies occur on the same lode, which strikes north and south and dips practically vertically. On the same line, and of 1/2 a mile and a mile respectively to the north of the North Emu, are the small Rand and North Rand workings, where a big width of lode material has proved to be very low grade. In the North Emu the lode width averages 12 to 15 feet; it is seldom less than 5 feet and in places reaches 30 feet. In the South Emu the lode is wide, but only portion of it is payable.The lode is a mineralised bed occurring between massive lava flows on the east and a mixed series of tuft's and thin lava flows on the west. The lode material is hard, fine grained, and dark coloured, and generally has a faint banding which is believed to indicate a tuft'aceous origin of the original lode rock. Microscopic examination shows that the original lode rock has undergone considerable albitisation;' there has also been considerable formation of biotite which gives the lode material a characteristic sheen. The mineralisation consists of abundant fine pyrite, which is auriferous, and a lesser development of pyrrhotite which is, however, barren of gold.THE OREBODIES AND THEIR CHARACTERISTICSThe distribution of ore is best studied from gold contours, as these reveal features that cannot be detected in an ordinary assay section. Gold contours (see Fig. 3) are developed' by plotting the width and grade of all development and stoping assays throughout the mine on a longitudinal projection, representing each sample by a coloured dot according to a suitably chosen range of assay values, and then outlining areas of similarly coloured dots (see H. J. C. Conolly, Econ. Geol., April, 1936). Both width and grade must be taken into account and the simplest method of gold contouring is to use dwt.lft. values, but difficulties arise here with big widths of low grade and small widths of high grade ore. To choose an extreme case, 30 ft. of 2 dwts. and 2 ft. of 30 dwts. both equal 60 dwts.lft., and would therefore be given the same value in dwt.lft. contouring...

Jan 1, 1943

Ore from the Hill 50 Gold Mine, consists essentially of pyrrhotite, with minor amounts of pyrite, chalcopyrite, galena and gold, replacing "jaspilite." The gold is associated with the sulphides as shotty particles. About 8 per cent. of the particles are less than '0.010'mm.The Hill 50 Gold Mine, at Boogardie in the Murchison goldfield, about 300 miles north-west of Kalgoorlie, was first operated in 1898. From 1898 to 1917 it yielded 20,000 short tons of ore for a recovery of 6,225' fine oz. gold, equivalent to a recovery grade of 6.22 dwt. gold per ton.The present company since the beginning of its operations in September 1936 to June 30, 1954, produced 811,081 short tons of ore for a recovery of 242,554 fine oz. of gold, equivalent to a recovery grade of 5.98 dwt. gold per ton.The grade of ore (recovery grade) has shown a remarkable variation with depth. From the 120 ft. Ievel to the 300 ft. level, it averaged about 7.5 dwt. Au per ton. Below the 300 ft. level it declined, and from 300 ft. to 400 ft. averaged 4.9 dwt. per ton, falling further with increasing depth to about 4.5 dwt. per ton at the '600 ft. level.On the 820 ft. level the grade improved sharply to about 14 dwt: per ton, and this grade has persisted down to and on the 1060 ft. level.The orebody has been described by Finucane (1953) as a series of lenses of finely banded jaspilite conformably enclosed by greenstones. The jaspilite is tightly folded and faulted and intruded by dykes of felspar porpnyry.Mineralization is practically restricted to the jaspilite.

Jan 1, 1955

By C. G. Maier

Relatively infrequent use by metallurgists of the term "sponge chromium" as contrasted to more than occasional reference to "sponge iron" may be ascribed to the fact that the former material is not a commercial product, while the latter has been known and used, at least in one form (Swedish sponge iron), for several decades. It is doubtful whether a true sponge chromium ever has been prepared heretofore in the laboratory by more than one or two investigators. Nature presents a much. more difficult problem to the investigator endeavoring to make sponge chromium than pertains to the production of more easily reducible elements such as iron or nickel. Recent widespread interest among metallurgists in the possibilities of powder metallurgy is ample incentive to explore the feasibility of producing pure chromium metal in finely divided form. The shift in terminology of this statement from "sponge" to the "finely divided form" is deliberate in emphasis of distinction between terms that occasionally have been used loosely. It would seem desirable that a uniform usage descriptive of finely divided metals be adopted. While to some it might seem preferable that the terra "powdered" metal be reserved for a finely divided form produced by mechanical means, as, for example, chromium produced by the mechanical comminution of electrolytic sheets or flakes, current usage of the term "powder metallurgy' involves no distinction as to source type of material. It is usually accepted, however, that a sponge metal is one reduced from oxide or other combined form at temperatures below the melting point of metal or oxide so that the particles of metal are pseudomorphic, at least macroscopically, with the source material, and, in consequence of the loss of material without change of external shape of the particles necessarily have an open, porous, or "spongy" structure.

Jan 1, 1942

By B W. Riddol1s

The 1983 Energy Plan calls for an increase in North Island coal production from both underground and opencast sources from the 1982/1983 production of 843 000 tpa to approximately 3.4 Mtpa within the ten year period to March 1993. This increased production is scheduled to come from the following sources: Huntly West No 1 underground mine reaching full production of 1.26 Mtpa. Huntly East underground mine increasing production to 750 000 tpa. The proposed new Huntly West No 2 mine producing 100 000 tpa in its first year of operation û 1992. The proposed Ohinewai opencast producing 920 000 tpa for supply to the steelmaking plant at Glenbrook, replacing Weavers opencast which will be worked out in 1990. Rotowaro opencast producing at 220 000 tpa (currently being achieved). Two additional sources of supply which are not scheduled to begin production for at least ten years, and both of which have been designated for coal fired thermal power generation, are the Maramarua and Mokau coalfields. It was originally envisaged that development of both coalfields would be a combination of underground and opencast mines. The form of development is yet to be confirmed by detailed feasibility studies. The location of the Maramarua, Ohinewai (Waikare Coalfield) and Mokau deposits is shown on Figure 1. Worley Consultants Limited, in conjunction with their partners Rheinbraun Consulting GmbH (Germany) and Longworth McKenzie Pty Limited (Australia) have been involved with investigations and mining assessments for the Maramarua, Mokau and Ohinewai prospects. The Maramarua and Mokau studies form part of the New Zealand Coal Resources Survey programme of updating information to the Pre-Feasibility Mining Assessment level before proceeding to detailed feasibility studies. The Ohinewai study was commissioned directly by Mines Division to investigate the feasibility of mining coal by 1989 before reserves at Weavers opencast are depleted. This paper describes typical studies which are now being commissioned by Mines Division to investigate large-scale mining development and the effect geotechnical-conditions may have on coal recovery. The magnitude of these projects is reflected in the proposed outputs û up to2 Mtpa from individual mines û and the introduction of new continuous mining systems for both underground and opencast mines on a scale which has not previously been contemplated.

Jan 1, 1984

By I M. Turnbull

QMAP (the Quarter Million Mapping Programme, 1:250 000 scale) is a geological mapping programme which will build a digital geological database of the whole country and publish maps and books to document it. The programme was established in 1993, following a recommendation by a review panel appointed by the Ministry of Research, Science & Technology, and is funded by the government, from the Public Good Science Fund. The relevance and fundamental value of QMAP lies in the greatly improved geological knowledge it will provide for researchers and other end-users of geological information.   QMAP research involves assessment of previous work, field and laboratory investigations in key areas, and data storage, manipulation and publication using Geographic Information Systems (GIS) computer technology. The QMAP digital database of New Zealand geology will be completed by 2006, as will the series of 21 full colour printed geological maps and accompanying explanatory texts. Two are already completed and published (Kaitaia and Dunedin), and six other projects are well advanced.   QMAP information will also be available in digital form. Next year we hope to expand the scope of the programme to cover the reconciling and linking of many other earth science databases to QMAP, because we believe this will create a powerful research tool. The intention is to develop internet access to the databases, to make the information publicly available.

Jan 1, 1997

By G Anderson, M Mativenga, C Stanton, M Larson

Arrium’s magnetite concentrator has recently completed a modification program to improve the process that has been in operation in Whyalla, South Australia for the previous seven years. The magnetite concentrate is pumped via pipeline to the coast and serves as pellet plant feed, eventually being turned into steel in the Whyalla blast furnace. With the addition of a new 3MW IsaMill at the concentrator, the plant has seen increased production from a reduced feed grade, enabling Arrium to treat ores previously stockpiled as waste. This paper will focus on the design work and commissioning of the fine grinding circuit along with the year of optimisation that followed, taking the IsaMill up to 350+ tph of throughput.CITATION:Larson, M, Anderson, G, Mativenga, M and Stanton, C, 2015. The Arrium IsaMill from design through commissioning and optimisation, in Proceedings MetPlant 2015, pp 110–119 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

By Giannini M

Of the optimization techniques proposed in determining the optimum open pit limits, dynamic programming and graph theory have proved most successful. However, publications on these two methods lack a certain amount of rigour and clarity in exposition. Certain ideas in the methods have been clarified and additional features introduced in order to make them more sensitive to practical applications. A case study in the form of an application of these ideas on data from a producing mine is presented and discussed.

Jan 1, 1986

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mud-stoneovercored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2000

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012