Search Documents

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground nine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.8 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated. Rock dust was employed chiefly in the larger mines, which numbered only 431 out of 6,016 underground mines in operation in 1935, according to reports from mining companies. The mines in which rock dust was used had an average of 288 underground employees per mine, whereas mines in which rock dust was not used averaged only 62 underground employees per mine.

Jan 1, 1940

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground mine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.9 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated.

Jan 1, 1940

By Mark A. Willian

The purpose of this short paper is to present soil profiles and basic soils information for the portion of the I-880 Replacement Project alignment where highway structures are to be built. The information presented here is derived primarily from foundation investigations conducted by the Caltrans Foundation Unit (currently the Structures Foundation Branch, Office of Structural Foundations) and by others under Caltrans direction. The foundation investigation for the I-880 Replacement Project began in May of 1991. The field work was completed in May of 1992 and consisted of 93 rotary sample borings, 11 consolidation sample borings, 6 TEXAM® pressure meter borings, six in-place vane shear borings and 57 electronic cone penetrometer soundings.

Jan 1, 1996

By R. E. Robinson

A novel variation of the GYPCIX process for the treatment of the acid mine effluent water from Grootvlei is described, in which a number of valuable by products can be obtained and the product water can be used for a variety of different purposes. A conceptual case study is presented in which the important cost parameters are described and certain critical path activities are indicated in order to derive a Return on Investment evaluation according to methods previously published. The study indicates that the treatment costs can be dramatically reduced, provided that proper utilization of the by products is taken into account. There are many possible uses for the water. However, by far the most advantageous contribution to the RDP and the best return on capital is derived if the water is used to establish small-lot farming activities providing work opportunities for thousands of people and contributing several hundred million Rands to the GDP. Vastly improved social conditions will be generated in an area of Gauteng that is in danger of rapid deterioration and a contribution will be made to maintaining mining activities in this area. The environmental impact is positive.

Jan 1, 1998

By William E. Young

There are many large rhodonite-bearing veins containing manganese in the Eureka-Animas Forks area of the San Juan Mountains in Colorado. The Sunnyside vein is the largest known vein in the area. As observed on the surface, the vein is mineralized over 8,000 feet and attains a maximum width of 200 feet. The average width of the vein and its branches and ramifications is 58 feet in the area that was mapped in detail. The weighted-average analysis of surface and underground samples from the northeastern extension of the Sunnyside vein is 8 percent manganese. Most other known veins in the area have a similar manganese content. The Hidden Treasure vein lies southeast of the Sunnyside-No Name-Mastadon vein. The weighted average of the analyses of surface and underground samples from this vein is 13 percent manganese. Exposures of the Scotia-Silver Chord vein are visible over a strike length of 4,000 feet on Treasure Mountain. Diamond-drill holes show that the vein contains 10 percent or more manganese to a depth of 400 feet. The vein has an average width of 28 feet. The Independence vein is exposed on the surface for a distance of 600 feet and has an average width of 6 feet. Three cut samples taken across the vein had an average content of 20.7 percent manganese. Sampling of the outcrops of eight veins in the Placer Gulch area also indicates manganese. Numerous other veins cropping out in the surrounding area are similar to the outcrop of the Sunnyside vein system mineralogically and are worth investigating.

Jan 1, 1966

By Thomas M. Barczak

This US. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (5) compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 2010

By W. J. González

"With the increasing demand for minerals, technologies to maximize mineral recovery are paramount to a mine’s economic success. Many mining process waters have the potential to form calcium-based inorganic scales, which inhibit effective mineral recovery. Often, the solution to inhibit these deposits is the implementation of a chemical antiscalant program. This paper examines the application of a fouling analyzer to continuously monitor the formation of inorganic scale in mining process streams. The fouling data can be used to compare antiscalant programs and to optimize antiscalant feedrates. Case studies validate the ability of this technology to help optimize mineral recovery processes.INTRODUCTION The mining industry uses significant quantities of water. From quarrying, to crushing, to flotation, leaching, and refining, water is often the integral motive force to move slurries, separate or agglomerate fines, and extract and purify minerals. As well, water is used in a number of ancillary applications at mines, including dust suppression, gas scrubbing, and utility processes such as boiler, cooling, and waste water operations. For many processes, the quality of water being used is inconsequential. However, for certain processes, such as flotation, leaching, and desorption / stripping, water quality plays a key role in the ability of the operation to economically recover the target minerals. Dissolved solids such as calcium and magnesium salts can concentrate in process waters, exceed their solubility limits, and precipitate as scale on metal surfaces such as feed and transfer pumps, piping, and equipment. Some of the more common scales that form in mining operations include calcium carbonate (CaCO3, or calcite) and calcium sulfate (CaSO4, or gypsum), and to a lesser extent, calcium and magnesium silicate compounds. Any scale that deposits in a process stream will negatively impact mineral recovery, and increase the operational costs of the mine site. Whether it is acid washing a scaled heat exchanger in a carbon strip at a gold operation, replacing plugged emitter tubes in a leaching operation, or hydroblasting process lines in a scrubber unit, there are costs associated with labor, cleaning chemicals, repairs, and replacement parts. These costs pale in comparison to the potential costs of downtime and lost production, should the scale deposits occur in a process that is critical to the recovery of the target mineral."

Jan 1, 2014

By G. Gomez Ciments-Calcia

The sources of complaints by neighbours of the operating quarry are due to the 3 following causes : - Impulsional noises or air hoch wawes – Vibrations - D u s t How a blasting in a quarry operation is felt by neighbours cannot be measured solely by the various limits set by national and European regulations regarding vibrations and air shock waves (sound pressure).

Jan 1, 2002

By Osetzky D, Hesp W. R

The treatment of a hydrobiotite containing 0·64 per cent copper with various soluHons showed that a high percentage (up to 90 per cent) of the copper can be extracted under mild conditions (1 M BCI, 85°C) or withsaline solutions (20 per cent by weight NaCI or NH4F, 400°C). The latter results suggest that the copper is incorporated in the interstratified vermiculite of a vermicuHte-biotite mica and the solutions (NaCl and NH4F) which reacted with the vermiculite without attacking the biotite gave the highest extraction yields.In general, extraction yields with saline solutions increased with the temperature (between 100 and 400°C) and duration (3 or 6 days) of the treatment but were not appreciably affected by the initial pH of solutions.The results of RCI treatment especially may have a bearing on the hydrometallurgical treatment of refractory copper ores where copper is tied to gangue silicates.

Jan 1, 1977

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By Manoj Kumar, S. Ranganathan, S. N. Sinha

The reducibility of three different manganese ores with coke was studied. The three ores were reduced to different extents under the same experimental conditions. The investigations showed that in the temperature range of 900-1000 ×C, Fe2O3 in the ore was reduced to metallic iron. MnO2 was reduced to Mn3O4 in all cases except one in which it was reduced to Mn2O3. The kinetics of reduction was controlled by different mechanisms in the different ores. Temperature had a significant influence on the reducibility of the ores.

Jan 1, 2007

By S. Luyckx

This paper reports hardness and abrasive wear resistance test results from a wide range of WC-Co alloys, varying in cobalt content as well as WC grain size. The results show that the abrasive wear resistance increases with increasing hardness and that the rate of increase is higher for larger WC grain sizes. The increase in abrasive wear resistance was found to be parabolic up to a critical hardness value and exponential above that value. The transition from parabolic to exponential behaviour was found to occur at the same contiguity value for all grain sizes, which suggests that at that contiguity value the WC skeleton becomes continuous in all WC-Co alloys.

Jan 1, 2004

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Extensive testwork on atmospheric thermal magnesium production has highlighted certain important fundamental and operational factors that have a major influence on magnesium extraction and its extraction rate, the condensation efficiency of magnesium, as well as on the quality of the condensed metal. The possible impact of these factors on the selection and preparation of raw materials, recipe choice, furnace electrical energy consumption, and on the refining requirements of the crude magnesium is discussed. Selected pilot plant operational and metallurgical data are also presented.

Jan 1, 2006

By Juan García

En el Perú, uno de los mayores problemas para evaluar certeramente la hidrología de cuencas y sus cabeceras, es la falta de información meteorológica, especialmente el de precipitación. En ese sentido, es necesario el uso de modelos de representación matemática de la física que gobierna los fenómenos hidrológicos (por ejemplo, evapotranspiración e infiltración). Sin embargo, dichos modelos no son aplicables puesto que son empíricos. Por ello, el presente trabajo describe la forma de superar estos obstáculos a través del uso del modelo hidrológico SWAT para evaluar el balance hidrológico de diferentes cuencas en el país, así como el de la cuenca del Alto Marañón hasta la localidad de Corral Quemado, donde la información meteorológica, de suelos, topografía y de vegetación se integra con el modelo hidrológico para obtener balances hidrológicos a nivel de (sub)cuencas.

Oct 21, 2015

By J. M. Ortiz

Mineral resource evaluation requires defining geological domains that differentiate the types of mineralogy, alteration and lithology. Usual practice is to consider the domain boundaries as hard, i.e. data from across the boundaries are disregarded when estimating the grades within a given domain. This practice may hinder the quality of the estimates when a significant spatial correlation of the grades exists across the domain boundaries. In this paper, several geostatistical methodologies to handle soft geological boundaries are compared through a case study on a copper mine in Chile. The estimation methods considered are: ordinary kriging using hard boundaries between geological domains; ordinary kriging omitting the geological boundaries; traditional and standardized ordinary cokriging of the grades assayed in different domains; ordinary kriging within dilated geological domains, that is, incorporating samples from adjacent domains up to a given radius from the boundary of the domain being considered. The estimations are performed using a set of exploration data (drill hole samples) and are validated using a set of production data (blast hole samples collected for grade control). Results indicate that kriging with dilated domains performs better than ordinary kriging using hard boundaries or no boundaries and better than the ordinary cokriging approaches. It therefore appears as a simple alternative to global kriging (without considering the geological domains) and allows accounting for changes in the grade average, dispersion and spatial continuity with the geological characteristics of the deposit, via the use of grade variograms proper to each geological domain. The maximal distance for searching samples from adjacent domains should be chosen according to the spatial correlation of the grades across the domain boundaries, or via a cross-validation at an early stage of the mine or a jack-knife if production data are available. Keywords: Kriging; cokriging; soft boundaries; hard boundaries; geological control; geological domains.

Jan 1, 2006

By T. M. Barczak

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of ?topping off? the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

Jan 1, 2008

By M. G. Zabetakis

This publication describes an investigation conducted by the Federal Bureau of Mines regarding the cause of an explosion of a dephlegmator or fractionating column at the Cities Service Oil Company Refinery, Ponca City, Okla., January 22, 1959. The column was that used with the refinery's No.1 Dubbs Coker. The explosion caused the death of an employee of the refinery and resulted in extensive damage to the refinery and to nearby property. The Bureau's study of the explosion began January 26.

Jan 1, 1960

By Narasimhan K. S, Sastri S. R

A typical high silica low grade magnesite from the Salem area of Southern India, was used in studies to develop a suitable flotation system involving commercially inexpensive sodium oleate as the collector together with other reagents which can give a product of the required grade with an acceptable recovery. It was found that the presence of metallic ions such as Cu+, Fe+++ or Ca++ introduced by the addition of their salts, or by their formation with the addition of hydrochloric acid to react with magnesium and calcium carbonate in the me, can act as effective depressants for silica. The addition of 'hydrochloric acid' was found to give best results.

Jan 1, 1980

By Daniel L. Ng

This Bureau of Mines report describes the results of scanning electron microscopic (SEM) studies of the combustion residues of carbonaceous dust particles resulting from explosions and thermal ignitions in laboratory and full-scale mine tests. The dusts studied varied widely in rank and volatility: Pittsburgh seam bituminous coal (35% volatility), Pocahontas seam bituminous coal (16% volatility), anthracite (7% volatility), graphite, and diamond. The most systematic explosion studies were performed in an 8-L chamber with narrow size distributions of Pittsburgh coal dust with surface mean diameters of 2, 22, and 84 pm. Experiments were conducted mainly in air, with some data obtained in 50% 02. Observations of the bituminous coal explosion residues showed particles with rounded edges, particles with blowholes, and some cenospheres. The lower volatility dust residues showed fewer changes from the original, unburned dust. In addition to the experimental studies, results of SEM observations of residues from a mine explosion disaster are reported. Comparison of such residues with those from the laboratory and experimental mine explosions can help investigators determine the extent of dust participation in the disaster and in identifying the possible ignition sources.

Jan 1, 1983

By R G. Barker, A B. Christie

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. More than 11 Moz of Au and 50 Moz of Ag have been produced from epithermal deposits in New Zealand, almost entirely from 50 deposits in the Hauraki goldfield. Since the 1980s, new deposits have been discovered at Waihi (Favona, Trio, Correnso) and nearby at Golden Cross. Feasibility studies into reopening the Talisman mine at Karangahake are continuing, and advanced projects with preliminary inferred resource estimates are reported at Wharekirauponga, Neavesville and Muirs. In the Taupo Volcanic Zone, 11 prospects have been drilled, resulting in the definition of large but low-grade Au-Ag resources at Ohakuri. In Northland, several Au, Ag and/or Hg prospects are known, and small quantities of Ag and Hg have been mined. Six prospects have had some drilling, with the most advanced exploration at Puhipuhi. The application of Taupo Volcanic Zone geothermal systems research to the modelling of former hydrothermal mineralising processes in some epithermal prospects has enabled better targeting of exploration.CITATION:Christie, A B and Barker, R G, 2015. Exploration for epithermal gold deposits in New Zealand, in Proceedings PACRIM 2015 Congress, pp 533–540 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015