Search Documents

Draft tube circulators are now widely used instead of Pachucas for suspension of slurries in large tall tanks.Precipitators in the alumina industry are an example.Draft tube/tank diameter ratio is critical. Two independent criteria are given for optimum ratio. The hydraulic and energy relationships are defined. These require an impeller of very high specific speed. For a stable and efficient system the impeller should have aerofoil blades with a pitch angle which decreases from hub to tip.The draft tube must be matched to the impeller with inlet baffles above the impeller and flow control vanes below it. Tip recirculation must be suppressed. The tank itself should have a filleted flat bottom.Such a system exhibits the behaviour of axial flow devices with the characteristic undesirable behaviour at low flow.Installed and operating power requirements depend critically on hydraulic design and to a lesser extent on speed reducer efficiency.The problems of re-suspension have been overcome by a patented slot system which also improves behaviour at low flow to permit a more economic design. A number of other practical operating considerations are also discussed.

Jan 1, 1982

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By John Watson

The earliest known records related to mining document in dramatic terms the fact that mining methods have undergone significant change over the centuries. Wooden wedges, hammers and chisels, “fne setting”, to name a few, were the frst tools used to extract ore .or quarry rock for civilization. These inefficient tools and unsafe practices have been replaced today with some of the highest technology known to man. At the heart of most mining operations is the blasting program which utilizes one of the most efficient tools ever invented.. . explosives. Ever since they were invented, miners have been searching for more efficient products and methods with which to harness this “tool” and make it safer, reliable, and more eficient to use.

Jan 1, 1997

A massive cobalt-containing pyrite orebody occurs in banded albite-quartz-biotite rocks at Thackaringa, some 30 km SW of Broken Hill. Because of the world-wide shortage of cobalt during the late 1970s, serious consideration was given to the development of a suitable flow-sheet to recover the cobalt from this ore. Details of a pressure leaching process in which more than 90 per cent of the cobalt is extracted from a pyrite concentrate are presented.

Jan 1, 1983

By Stephen M. Smading

Unique onsite assembly of a 12.43 m Main Beam TBM and back-up system was completed on September 18, 2008 in the remote mountains of the Sichuan province of China. The equipment was assembled onsite, without previously having been assembled and tested in a factory, utilizing a method called Onsite First Time Assembly (OFTA). The Jinping-II hydroelectric project features four parallel headrace tunnels approximately 18 km long, two of which will be excavated by TBMs and two by drill and blast. A nearby fifth tunnel is being excavated by a 7.2 m TBM to draw down ground water in advance of excavating the headrace tunnels. This paper addresses the following topics: ¦Project description including geology and terrain; ¦The decision process leading to onsite first time assembly, the assembly process and logistics, and lessons learned; ¦Design features of the TBM and back-up system; and ¦Operational history from startup to the writing of the paper.

By Stephen P. Quin

One of the most prospective undeveloped greenstone belts in Canada, the Hope Bay greenstone belt extends over 80km in a north-south direction and is between 7 and 20km wide. The belt lies on the arctic coast and comprises mafic meta-volcanic and meta-sedimentary rocks that are bounded by Archean granite intrusives and gneisses. The greenstone package has been deformed during multiple events and is transected by major northsouth trending shear zones that appear to exert a significant control on the localization of mineralization. The Hope Bay belt contains a number of significant gold deposits hosted in a typical Archean greenstone belt and which occur in several geologic settings, including shear-hosted, lode-style and breccia-associated. Combined, the deposits host a measured and indicated resource of 1.6 million oz of gold averaging 15.7 g/t plus an inferred resource of 2.7 million oz of gold averaging 12.3 g/t. All deposits remain open to expansion. Exploration in the period 2000-2002 by Miramar includes more than 110,000m of drilling to more fully define the nature of the known deposits, while regional exploration has focused on identifying and evaluating new targets. In carrying out its programs, Miramar uses a number of techniques to improve its chances of exploration success. Activity in 2003 includes 43,000m of drilling focused on expanding resources in the Madrid area, testing the Boston deposit at depth and continuing the hunt for more discoveries. Meanwhile Miramar is advancing one of the deposits towards a production decision, based on a low capital, high return development scenario.

May 1, 2003

By Luis Vassallo

El presente trabajo señala los beneficios que pueden obtenerse de la adopción inteligente de una estrategia de colaboración electrónica que responda a las necesidades de este segmento y que proporcione soluciones de verdadero valor agregado. Así, el modelo monolítico que prevaleció por muchos años, donde cada empresa era propietaria de las licencias mineras, operadora, mantenedora, contratista, vendedora, embarcadora y financiera, está desapareciendo. En la cadena de valor del proceso minero intervienen más empresas, contribuyendo valores agregados específicos y especializando funciones. Este cambio demanda mayores flexibilidades de los sistemas de información que deben ser totalmente abiertos, y permitir el intercambio instantáneo de información que facilite reaccionar oportunamente a las diferentes variables de la operación. Por ello, la colaboración electrónica permite a la minería adaptarse a un mundo que está cambiando.

Aug 25, 2002

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By M. A. Oskouei

Draglines are the main energy consumers in strip mines. Given the growing cost of energy and environmental concerns, it is important to properly understand dragline energy efficiency. The goal of current research at Missouri University of Science & Technology is to account for operator practice and operating conditions in modeling dragline energy efficiency. This paper presents preliminary correlation analysis and a framework for stochastic modeling of dragline energy efficiency. Thirteen operating parameters (including cycle times, payload, swing angle, and height of dump pile), operator working schedules, operating conditions, and drag, hoist, and swing energies were monitored for an 85 yd3 dragline. Operator effects were examined by two-sample t-tests. The relation between the parameters and energy consumption were assessed by correlation analysis and a stochastic modeling framework has been proposed for dragline energy efficiency. The results show that operator effects are significant (p< 0.05) and energy efficiency is correlated with operating parameters. The completed model will help the coal mines better predict energy consumption, with uncertainty, for different operating conditions.

Feb 27, 2013

By M. S. Riyazulla

A model of a new laboratory magnetic separator has been conceived to cater the needs of process engineers and mineralogists world over engaged in mineral characterization and beneficiation. It would be essentially a laboratory instrument for the separation and concentration of various ferro and non-magnetic minerals. Based on the basic concept of Frantz Isodynamic Magnetic Separator, the new separator conceived would not only speed up the work of a process mineralogist and save the energy, but it would effectively separate and sequentially produce about fourteen fractions at a time. In the present paper, the probable operational procedures and the design have been discussed in detail for the various mining companies to assess its economic feasibility. If it could be fabricated, it would have a worldwide market The concept has been patented in author?s name in India.

Jan 1, 2009

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By J. W. Jamieson, J. Escartin, A. Steinführer

Evidence of hydrothermal activity on two Mid-Atlantic Ridge oceanic core complexes (OCCs), at 13º30’N (the Semyenov 1 through 5 fields) and 13º20’N (the Irinovskoe field) (Fig. 1) were studied using CTD casts, dredges, TV-grabs and SP surveys during previous research cruises to these sites (Cherkashev et al., 2013, McLeod et al., 2009). In late 2013, the Semyenov and Irinovskoe fields were revisited, this time with an autonomous underwater vehicle (AUV) and a remotely-operated vehicle (ROV) during the ODEMAR (Oceanic Detachments at the Mid-Atlantic Ridge) cruise on the French research vessel "Pourqoui Pas ?". Here we present the first visual surveys and direct sampling of these vent sites. High-resolution (~2 m) bathymetry of the 13º30’N and 13º20’N OCCs and their associated vent fields was collected during 4 and 5 AUV dives, respectively, using the GEOMAR AUV "ABYSS" (Fig. 1). These surveys were flown between 70 m and 100 m above the seafloor, typically at a constant height to reduce vehicle movement. The AUV was equipped with Eh, turbidity, and temperature sensors in order to detect active hydrothermal venting. Over twenty ROV dives with the ROV "VICTOR 6000" allowed for the visual exploration of the OCCs and collection of 59 hydrothermal rock samples from the vent fields. As a result of these exploration activities, the first robust estimates of the size of the deposits, and the geologic controls on sulfide accumulation at these sites can be determined.

Sep 1, 2014

By V Barrera, A Brzovic, M Gaete, L Burgos, E Arancibia

Fragmentation is one of the most relevant parameters in the design and operation of a mine using the caving mining method. Fragmentation affects all subsequent operations, including extraction, comminution processes, secondary blasting and transportation.There are a number of different models in the literature to estimate the size of the ore fragments that report to the drawpoints; however, there is still no industry consensus about which one to use. This paper proposes a new model for predicting the fragmentation reporting to the drawpoints that is based on the geotechnical unit characteristics, extraction height and column of primary ore. The model is developed from observations of fragmentation measurements in different mine sectors of Codelco’s El Teniente mine in Chile.This work focuses on the following three steps:collecting fragmentation and hang-up data from several mine sectorsdeveloping a geotechnical block model using oriented core placed within the main geotechnical unitsanalysing the data and modelling the fragmentation process.The proposed model is used to discuss the mechanisms and the influence of preconditioning on the size of the ore fragments that report to the drawpoints.CITATION:Brzovic, A, Vallejos, J, Arancibia, E, Burgos, L, Delonca, A, Gaete, M and Barrera, V, 2016. Analysis and modelling of the fragmentation process – case studies at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By W. H. Emens

[This circular is one of a series dealing with tie development and equip¬ment of small and medium size mines, and with the costs of such work prior to productive operation. The preparation and publication of these papers by the Bureau off Mines has been made possible through the cooperation of various min¬ing and development companies. The bureau of Mines has published a series of circulars dealing with min¬ing methods and costs at a large number of producing nines in the United States, Canada, Mexico, an, other countries. Unit costs of development work, shaft sinking, (rifting, crosscutting, tunneling, and raising are usually much higher in the preliminary development of a property than during its productive life.]

Jan 1, 1933

By Matthias Baeßler, Markus Herten, Ernst Niederleithinger, Steven Georgi

"Abstract: BAW and BAM have performed a large scale comparison and calibration test on static and dynamic load capacity evaluation of bored piles in glacial sandy soil. The test was performed using eight piles at the BAM test site for technical safety at Horstwalde 50 km south of Berlin. The test area has been prepared and investigated in great detail using boreholes, cone penetration tests, pore pressure sensors and geophysical methods to assure controlled conditions for all piles and tests. The piles (10 m length, 0.9 m diameter) are mainly friction piles (low toe resistance) and have been checked by integrity testing. Five piles have been tested by five contractors using the dynamic method in a blind experiment, the other ones piles by static load and/or later on by the dynamic method. Some piles have been equipped with additional fibre optic instrumentation which proved to be robust and helpful in interpreting the results of static, dynamic and integrity tests. We have experienced a deviation of the dynamic load test results gathered in the blind experiment from the static values of up to 20% in most cases, sometimes even up to 30%. This can be related to the known soil inhomogeneities, interpretation and modelling in CAPWAP and method inherent uncertainties. In cases where the static values were known by the testers for calibration, the deviations were significantly smaller. It has to be taken into account, that the two static load tests showed different results as well. Due to the low toe resistance, use of a big drop weight (11 tons) and large drop heights most piles suffered from cracking, which was clearly seen in follow up integrity tests and confirmed by excavation. The piles are available for further research.IntroductionBored piles are used in many construction projects of the German waterways authorities, e. g. bridges, piers or locks. Their load carrying capacity varies with pile type and geometry as well as soil type, parameters and structure and is thus not easy to calculate in advance. Dynamic pile testing as a cost effective addition or replacement for expensive load tests is accepted in many places (Beim and Likins 2008) but still doubted in others. Inspired by the international prediction event for piles in residual soil carried out in the frame of ISC’2 (Viana de Fonseca and Santos 2008), governmental research institutes have designed an experiment in a geological setting typical for glacial and post-glacial areas in northern Germany. Some results have already been presented by Niederleithinger et al. (2012), Herten et al. (2013) and Baeßler et al. (2013). It was intended to perform a blind test for load capacity estimation using dynamic pile testing on six drilled shafts involving five test crews. Two other piles would have to be tested thereafter using static and dynamic methods."

Jan 1, 2014

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey&apos;s results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By S McKinley, S Juras, E Uludag

More and more, today’s mining geologists are asked to identify and create 3D value domains for multidisciplinary usage: grade definition, geometallurgical performance and geotechnical characteristics, to name a few. Often, that domain shape is the result of an assumed or conjectured value as a surrogate to a set of conditions (eg kaolinite-rich, sericite alteration). Would it not be instead better to create the respective domain through identification of a consistent quantifiable geologically-based pattern as its basis?Critical to the identification of patterns is the transformation of 3D point data into a model by a method that uses few, if any, preselected thresholds. Too often we complicate the reviews of the modelled data by prejudging the value range of interest. And when we do revert to 2D views (ie sections and plans), we tend to only examine numbers or line traces. These hinder and obscure identification of geological patterns particularly in deposits of complex geology. Instead, these data should be looked at with minimal prejudgment and interrogated in 2D space by one of the best and most eye-catching display types: filled contour plots.Here we present two different processes that transform data with minimal preselection into formats that allow for pattern recognition by filled contour plots. These are: probability assisted constrained kriging (PACK) and multiple interval interpolant formation (Aranz Geo’s Leapfrog&#174; software). The former creates a 3D model of probabilities on a threshold value; the latter creates numerous (=10), regularly-binned 3D interval interpolants. The results of each method are examined as filled contours over numerous sections or plans. Any distinct patterns are quickly discerned thereby readily identifying the best value to base the creation of a domain. These processes therefore provide a way to marry recent advances in software tools with what is supposed a geologist’s core skill: pattern recognition.CITATION:Juras, S, McKinley, S and Uludag, E, 2017. Pattern recognition in transformed data – the search for domain shapes in mine geology data, in Proceedings Tenth International Mining Geology Conference 2017, pp 37–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By N Stoitis, L Lien, B Tapley

The treatment of hypersaline waters originating from numerous gold projects within the Western Australian Goldfields region via membrane technology has been assessed. A combination of Ultra-filtration (UF) and Nano-filtration (NF) using Ecotechnol’s modified elements effectively removes the polyvalent ions responsible for the high lime and cyanide consumption as well as the prevalence of scale formation characteristic of gold operations in this region. Through removing up to 98% magnesium, 94% calcium and 99.7% sulfates from hypersaline water with total dissolved solids from 40,000mg/L to 250,000mg/L, Ecotechnol and subsequent independent tests have demonstrated up to an 87% reduction in lime consumption and through the ability to increase the operating leach pH, reduce cyanide consumption by up to 28%.CITATION:Tapley, B, Stoitis, N and Lien, L, 2015. Modified nano-filtration membrane treatment of hyper-saline goldfields water – an overview and benefits to gold plant operation and economics, in Proceedings MetPlant 2015, pp 431–463 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

"This paper describes some of the methods and equipment used for fine milling of minerals, and gives particular attention to the Vibro Energy system.In addition, the paper describes a specific application in the gold mining industry. This is the 200 tpd plant built by Anglo American Corporation at the President Brand Mine in South Africa in 1985, now a division of Freegold. This plant treats a gold bearing pyrite flotation concentrate which is finely ground to 15 microns prior to cyanidation and carbon-in-pulp (CIP). l .0 INTRODUCTIONFree milling gold ores are those that yield acceptable dissolution and recovery of the gold following grinding to what can be described as normal fineness, frequently between 50% and 90% passing 74 microns.Increasingly, gold metallurgists are faced with ores that are refractory. The traditiona1 treatment route for refractory gal d ores and concentrates has been by roasting, but for environmental reasons this is becoming less acceptable, or in some areas of the world, totally unacceptable. New methods of treating refractory gold ores are being developed and applied in practice. These new methods include pressure and biological oxidation. Higher gold liberation can also be attained by increasing the fineness of grind, although with conventional systems there are economic limits to this.In flowsheet development and test programs on new deposits, a standard procedure is to establish the relationship between the grind and subsequent go 1 d extraction. The normal situation is that gold extraction increases as the ore, or concentrate, is ground finer. Typically, this relationship is as shown in Fig. l, where the incremental additional extraction is very small once an optimum, or economic, grind has been achieved. This generally app1ies whether the material is free milling or refractory. The limits to grinding are set by the type of equipment which is commonly in use, usually ball mills. These mills have the obvious advantage of high capacity, however, they are increasingly inefficient as finer grinds are required. In general, ball mills are used to reduce ore to some agreed percentage passing 74, or possibly 53 microns."

Jan 1, 1988