Search Documents

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991

By M. A. W. Bryson

Platinum group metals are extracted almost exclusively in South Africa from three very different zones in the Bushveld Igneous Complex, called the Plat, Merensky, and the UG-2 reefs. The Plat reef is currently being exploited only by Anglo American Platinum, whereas the Merensky reef is exploited by them, Impala Platinum, Northam, and Lonplats. The UG-2 reef, on the other hand, is also processed by these producers, but Kroondal and Barplats have operations that exclusively treat ore from this reef. At present the extraction of pgms from ores in South Africa follows the traditional route of upgrading to a concentrate in a minerals processing circuit, further upgrading to a matte in a smelter, and final upgrading and separation of the individual metals in a refinery. Thus all operations that extract pgms require a minerals processing circuit, the design and performance of which is a topic of much interest, as it is a poorly understood and not a very efficient process in relative terms, compared to the other processes. Recoveries across the minerals processing circuit of between 75 and 90% are the norm.

Jan 1, 2004

By R. A. Strehlow

This is the final report for U.S. Bureau of Mines contract HO-122122, which was in effect from June 30, 1972 through January 4, 1976. The work resulted in the design and construction of a large laboratory scale coal dust burner and the use of this burner to study gaseous and coal dust flammability. A new technique for determining gas phase flammability was developed and the effect of solid and gaseous suppressants on the propagation of coal dust flames was studied. In addition, a technique for measuring the C/H ratio in the flame was developed and the C/H ratio that was measured in a coal dust flame on this burner showed that the burning process was preceeded by pyroysis of the coal dust. Both experimental and theoretical studies showed that radiative trans-port is very important to the propagation of a coal dust flame.

Jan 1, 1977

By Ken Witherly

Modern airborne EM surveys typically acquire more data than is processed or analyzed at the time of acquisition Suitable additional processing can provide more diagnostic information, thereby allowing for more effective ranking and hopefully, follow-up of outcomes

Apr 1, 2005

By H. B. Carroll

The performance of commercially available portable instrumentation for detecting nitrogen dioxide, sulfur dioxide, and hydrogen sulfide was evaluated. Length-of-stain detector tubes from several manufacturers were included in the study. The instruments were evaluated in atmospheres with 50-and 80-percent relative humidities at 75° F and containing test gas concentrations of 0.1, 0.25, 0.50, 1.0, 1.5, and 2.0 times the threshold limit values. The results from the gas analyzers were correlated with the known contaminant concentration by calculating and plotting an estimated line of regression, confidence limits, and correlation coefficient for each detector system. An increase in the relative humidity from 50 to 80 percent at /5° F changed the instrument response to the contaminants. The uncertainties in detection precision reported are for the observer-instrument system. The main difference or inconsistency in toxic gas concentrations determined with length-of-stain tubes resulted from the observer's interpretation of the results rather than from a predominant difference in the tubes.

Jan 1, 1975

By R. W. Welker

A technique was developed for sampling and analyzing airborne dusts in diesel-operated, underground, metal, and nonmetal mines. Samples were taken using personal respirable samplers, operated as area samplers, and an 11-stage cascade impactor. Real-time particle size distribution and concentration measurements were made with a quartz crystal micro-balance cascade impactor and a portable electrical aerosol analyzer. The materials characterized were minerals (by XRD), elements (by XRF), particle size distribution and concentration (gravimetrically), and organic constituents (by HPLC). The method was used to characterize dusts generated at the chute pulling operations on the main haulage level of an underground tungsten mine. Analysis showed that respirable dust concentration ranged from 0.8 to 2.3 mg/m3. It consisted of silica (3-7%); organic constituents from diesel exhaust (0.11-0.31 mg/m3 equivalent airborne concentration); and mineral dust (39-100%). The remainder was diesel exhaust particles. It was concluded that size selective sampling may be used to estimate the ratio of diesel exhaust to nondiesel dusts in the respirable fraction.

Jan 1, 1982

By R. C. Warner, L. Mills, S. D. Botts, M. Marticorena

The Antamina Mine is located in the mountainous region of the Ancash Department of Peru at an elevation of approximately 4200m.The 120 km main access road crosses the headwaters of numerous high-value trout streams and is adjacent to pristine lakes, some of very high ecological and scenic value. In addition, the mine discharges mine water and tailings supernatant to the Antamina and Ayash watersheds. These streams provide the primary water supply for irrigation by local residents and provide excellent fishery habitat. The rock walls and earthen diversions constructed by historic and current indigenous residents of Peru are world-renowned and local residents continue this tradition, passed down from the Inca Civilization, for both agricultural purposes and water distribution. The key elements of sustainable development – economic, environmental and social development have been incorporated into Antamina’s sustainable development program through integration of indigenous knowledge and capabilities into enhanced storm water, erosion reduction and sediment control systems. Examples of incorporating indigenous technologies and knowledge into cost-effective and environmentally sound environmental controls are:(1) placement of rock walls on steep terrain to reduce slope length and erosion, (2) installation of rock walls (porous rock check dams) within elongated sediment ponds to increase detention time, (3) construction of rock-lined ditches to convey clean water (4)use of rock walls, with or without geotextile, to function as a seep berm, and (5) appropriate selection and usage of native Andean species for protection of canals and sediment ponds, and steep slopes.

Jan 1, 2004

By Henk E. Brassinga

In Rotterdam a number of underground parking facilities have been built and are under development in the inner city, and in the suburbs. These parking facilities are located at already densely built areas. The design of these constructions has to take into account the impact of the building activities and that of the final construction on the surroundings. In this paper some examples of the different building methods of newly realized underground parking facilities are described, and problems that occurred during the construction are pointed out. In the soil conditions as present in Rotterdam the cost effectiveness of underground facilities can be improved by deepening the parking facility, and at the same time reducing the surface area so that the total parking volume remains constant. In this way the total volume of the diaphragm walls and the costs of the project is reduced.

Jan 1, 2006

With the employment of a system of ore pillars to support the hanging wall during the mining operations at the North Mine, it was found that, when the stopes were worked out and the pillars remained intact, the main footwall drives developed an undulating longitudinal section due to the shrinkage of the filling in the worked out stopes.These depressions collected water, which made the footwall drives very wet under foot, and everitually worked its way into the pillar workings and the levels below.Water was also finding its way into the shafts because of the silting-up of the level drainage systems and, as both the shafts are down-cast, this tended to increase the humidity of the air entering the mine.To overcome these troubles it was decided to try a system of siphons as a method of subsidiary drainage.SYSTEM AT PRESENT IN USE.All drainage water is collected as near to its source as possible, run into a sump in an adjacent low lying part of the level, and continuously removed from these sumps by a siphon system.Each level has its own system. Water is collected from the sumps by a 1-in. pipe and delivered to a pipe running the length of the level along the back of the footwall drive. At the shaft the pipe is increased to...

Jan 1, 1938

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By H. T. Kennedy, J. E. Little

An empirical equation for the prediction of the viscosity of several pure paraffin hydrocarbons and nitrogen is presented. It involves temperature, pressure and six constants of the material, and it applies reliably to both liquids and gases. The equation is similar in form to van der Waal's equation of state. For the paraffin hydrocarbons methane through r-hexane and nitrogen, an average absolute deviation of 1.9 percent was obtained on 1,006 data points described in the literature by 14 authors. When this equation is extended to complex, liquid hydrocarbon mixtures, a correlation was obtained with an average absolute deviation of 9.9 percent. INTRODUCTION Equations describing the flow of gas and liquid through porous media contain the viscosity coefficient of the fluid. If other pertinent variables remain constant, the volume rate of flow is inversely proportional to this coefficient. In dealing with condensate fluids and volatile oils, however, the compositional effects resulting from changing pressure materially affect the viscosity. The effect of compositional changes also may be significant in certain secondary recovery or pressure maintenance processes, notably miscible displacement or gas injection. Early attempts to describe the performance of reservoirs utilized a volumetric material balance method wherein gas and liquid in the reservoir were identified as produced gas and liquid at the surface. This method of analysis proved adequate for reservoirs at moderate temperature and pressure that contained gas with moderately low amounts of condensable materials. The volumetric material balance procedures for "black oil" reservoirs leave much to be desired when applied to condensate and volatile oil reservoirs because phase behavior and compositional changes are relatively more important in these cases. The alternative is a compositional material balance, which in turn, requires a correlation of properties of the reservoir fluid with composition. This paper supplies this correlation in regard to viscosity, for reservoir crude oils. REVIEW OF LITERATURE The literature contains many empirical equations describing the effects of composition, temperature and pressure on the viscosities of pure liquids and binary liquid mixtures. However, the applicability of a majority of these equations is limited to very low pressures and to a small number of systems. Most of them, when applied to complex hydrocarbon systems, are of little value. The lack of utility of the majority of equations results from the fact that they were developed to show the separate effect of temperature, pressure or composition on viscosity, but not to predict the viscosity as a function of all three variables. And with the few exceptions noted below, they were developed to apply to much simpler systems than hydrocarbon mixtures. Eakin1 developed an equation for the viscosity of pure light hydrocarbons applicable in the gas, liquid and dense fluid regions, and in its most general form is written as µ - µo =A(ebP - e-cpk) The pure component viscosity at atmospheric pressure and temperature T, µo, was calculated using the Sutherland equation: µo = BT3/2/T + S The constants in Eakin's equation permitted the term e-CPk to become quite small at high densities (above 0.215 gm/cc), and the general equation would simplify to

Jan 1, 1969

By Edwin M. Thomasson

HELIUM SHIPMENTS in 1964 exceeded the volume shipped during the previous year for the 15th successive time. Shipments from Bureau of Mines helium plants were 667.4 million cubic feet,2 about 6 percent more than in 1963. Production at Bureau of Mines plants totaled 784.5 million cubic feet. An additional 3,193.1 million cubic feet, which was produced by private companies participating in the helium conservation program, was purchased by the Bureau and stored underground for future use. The Bureau of Mines continued to sell helium at $35 a thousand cubic feet, the price established in 1961. Substantial railway freight rate reductions for tank car shipments of helium went into effect during the year, resulting in a lower delivered price for helium. As the Nation moved ahead in the space age, it became increasingly apparent that helium would continue to play an essential role in research, in technology, in defense, and in industry.

Jan 1, 1965

By Antonio Karzulovic, Sergio Olavarría, Patricio Adriasola

The economical analyses of different Chuquicamata open pit mine planning scenarios, indicate that the pit closure should occur at latest in the year of 2017. However, about 60,000 m of drill holes have demonstrated that below the pit bottom there is a potential of 2.3 billion tons of ore. Hence, Division Codelco Norte developed the scoping engineering for a large underground panel caving operation, similar to El Teniente mine. This project considers the exploitation of a 2500 m 300 m footprint, with three 250 m lifts. The plan considers to initiate the construction in the year 2009, to begin the production in the year 2015 and achieve a production rate of 45 million tons per year in the year 2021. A large-scale transition from open pit to underground mining like this one presents three main challenges: (1) to include the geotechnical aspects relevant for mine design and mine planning, (2) to define the proper surface and underground infrastructure, and (3) to fulfil the project deadlines and to achieve the production targets. This paper summarizes this transition project and discusses these three main challenges.

Jan 1, 2006

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969

By Walter E. Lewis

The Cuyuna iron range in Crow Wing County, Minn., is the principal producer of manganiferous iron ore in the United States. The ore is mined from a manganiferous iron formation in the bedrock of the Cuyuna district. This iron formation is divided into two general lithologic types-thin-bedded and thick-bedded. The unoxidized, thin-bedded iron formation is composed of iron silicate with associated fine-grained carbonates of iron and manganese. The thick-bedded iron formation carries iron and manganese oxides with intimately associated silica. Oxidation and leaching of the original iron formation have been the most influential factors in producing manganiferous iron-ore concentrations in quantities large enough to exploit on a commercial basis. The unoxidized and the partly oxidized and enriched iron-formation materials are suitable as a source of ferrograde manganese ore. These materials have been classified according to their amenability to mineral dressing and degree of oxidation and leaching.

Jan 1, 1958

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By Kyle Selga, Christopher J. Greet

"The Pulp Chemistry Monitor (PCM) has been installed and operated in a number of concentrators in Australasia, and has produced some very interesting results. PCM measures the pH, Eh, dissolved oxygen, temperature and oxygen demand of process streams within a concentrator continuously and in real time.In the example presented in the paper the cleaner feed pulp chemistry is measured, and related back to changes in the mineralogy as well as variations in metallurgical response. For example, a decrease in Eh and dissolved oxygen as well as an increase in the oxygen demand. These changes in the pulp chemistry appear to coincide with increases in the feed grades, probably higher pyrite grades. Further, these variations in pulp chemistry and feed mineralogy have a negative impact on the concentrate grade and recovery.The implication is that if the pulp chemistry is monitored it is possible to predict changes in the mineralogy of the system, and from this the metallurgical response. Further, the changes in pulp chemistry can be used in a control system to counter the changes in mineralogy and maintain the metallurgy.IntroductionIt has long been recognized at a fundamental level that the flotation behaviour of sulphide minerals is dependent on the pH and Eh of the system (for example: Tolun and Kitchener, 1964; Woods, 1976). However, measuring pulp chemical parameters within an operating concentrator has had limited attention. Woodcock and Jones (1970a and b) were among the first to actually collect data from operating plants. Jones and Woodcock (1984) identified some of the chemical complexities of flotation pulps, and noted that most concentrators already operate at high levels of metallurgical performance but there was still considerable scope for improvement. These gains would, in part come from more effective chemical control. In the same volume, Healy (1984) discussed metal ion hydrolysis and precipitation, redox chemistry and how the surface chemistry of sulphide minerals can be influence flotation behaviour. The impact of grinding environment on the pulp chemistry and flotation response of a complex polymetallic sulphide ore is discussed by Forssberg and Subrahmanyam (1993). Their work essentially contrasts the pulp chemical and flotation performance of pulps ground with conventional ferrous grinding media to a fully autogenous system. The data suggested that the reduction or removal of iron hydrolysis contamination from the system could have a positive influence on flotation behaviour, and perhaps the first stage of “controlling” the chemistry of the system should be in the grinding circuit. Grano et al (1995) demonstrated that the collection of pulp, solution and surface chemical data could identify weaknesses within a concentrator, and from these data develop, test and implement solutions that improved the process. Greet et al (2006) showed that the pulp chemical trends observed through primary grinding and rougher flotation circuits of most sulphide flotation concentrators are approximately the same. There are differences in the magnitude of various pulp chemical parameters (pH, Eh, dissolved oxygen, temperature and oxygen demand) as a result of variations in the feed mineralogy and processes employed. Further, it was noted the Eh shifted to more reducing values of the ten days measurements were collected, and this change could be traced to an increase in the iron sulphide content of the feed. Metallurgically, this resulted in an increase in nickel recovery through the recovery of nickeliferous iron sulphides, and a decrease in nickel concentrate grade."

Jan 1, 2016

By Charle Pelley, Kosta Fytas, Peter Calder

"A computer model has been developed which is capable of evaluating alternative production schedules (long- and short range) of an open pit mine once the ultimate pit limits have been defined. The model user can choose the best alternative according to cash flow considerations and the particular mining conditions. The model involves a combination of simulation for long range production scheduling and linear programming for short range scheduling. IntroductionMining of mineral deposits in such a fashion so that, at depletion the maximum possible profit is realized, has been a very old problem of the mineral industry. In the past, when high-grade ore reserves were readily available and profits were very high, no question of optimum profitability was raised.However, recently the complexity of both open pit and underground mining has been increased tremendously. The additional problems of continuously rising production costs on one hand and of depressed metal prices worldwide on the other, have been demanding optimum profitabiliy from every mining venture .Particularly in the area of open pit mining, the sequence of ore and waste extraction has now become very important since the size of the pits and of the mining equipment has increased enormously. The process of open pit mining involves a continuous change of the open pit surface and there are many feasible plans of extraction which lead to the same final pit shape (ultimate pit limits). Each of these feasible plans generates a production schedule over the entire mine life, which mayor may not be optimal."

Jan 1, 1987

By K. Osburn

South Deep Gold Mine, owned by Gold Fields Ltd., is situated near Westonaria in the Gauteng Province of South Africa and mines the conglomerate bands of the Upper Elsburg reefs (Mondeor Conglomerate Formation) of the Witwatersrand Supergroup and the Ventersdorp Contact Reef (VCR) of the Ventersdorp Supergroup. The stoping and underground developments are mechanized. The Upper Elsburg reefs are mined by a variety of mining methods, including mechanized drift and fill, modified drift and bench, longhole stoping, and low-profile mining. Optimal mine design and scheduling for deep-level mechanized mining are complex, and success is highly dependent on detailed, robust, and accurate geological and geostatistical models. Geological structures significantly influence the sedimentological characteristics, distribution, and preservation of the Upper Elsburg reefs and VCR. Accordingly, particular emphasis is placed on the generation of a mine-scale structural model that accommodates the relationships between the older north-trending fault systems (West Rand and Panvlakte faults) and younger east-trending dextral wrench faults. Results from underground mapping, borehole intersections, and highresolution three-dimensional seismic data have been integrated to produce coherent three-dimensional geological models. The Upper Elsburg reefs suboutcrop against the VCR and comprise an easterly diverging clastic wedge, thickening from the suboutcrop position, to approximately 130 m at the mine?s eastern boundary. The Upper Elsburg reefs are characterized by conglomerate and quartzite bands forming multiple, stacked, upward-fining unconformity-bounded couplets. Palaeocurrent directions are dominantly from west-northwest to east-southeast, indicating that the more proximal deposits are preserved close to the suboutcrop, with distal facies to the east. Sedimentological modelling is applied to individual stratigraphic units and caters for facies definition. This is achieved through channel width (CW) kriging and fitting of type sections to borehole and mapping data. Homogenous geological geozones for each stratigraphic unit are thus defined within individual structural blocks on the basis of those sedimentological parameters that have been found to have a positive spatial correlation to gold concentration. These geozones then serve as constraints to the evaluation of the orebody. This contribution presents a summary of the modelling processes that are currently applied in the development of high-confidence, timeously produced geological models that are essential input for mineral resource estimation and mechanized mine planning and scheduling.

Jan 1, 2014