Search Documents

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

By Terry R. Neumann

During 1984, at the request of the U. S. Bureau of Land Management, U.S. Bureau of Mines personnel conducted a mineral survey of the 28,600-acre South Pahroc Range Wilderness Study Area (NV-050-0132). The Wit derness Study Area is located in Lincoln County, NV, about 900 miles north of Las Vegas. Five mineral properties and two mineralized zones were examined during this study; of these, one mineralized zone, two small prospect pits, and part of two claims are within Wilderness Study Area boundaries. Perlite resources were identified in the study area; however, no significant metallic mineral values were noted at any of the sites. The Wilderness Study Area is dominated by a Tertiary volcanic sequence consisting of an interlayered series of tuffs containing thin beds of volcanic pebble gravel, sandstone, and perlite. At the base of the exposed volcanic section, perlite occurs along a 2.4-mile-long zone that parallel s the study area&apos;s northeastern boundary. The perlite is suitable for filtration, insulation, and soil conditioning purposes, Because of prohibitive operation and transportation costs, the estimated 6 million tons of perlite occurring inside the South Pahroc Range Wilderness Study Area are classified as an indicated subeconomic resource.

Jan 1, 1986

By Foster Fraas

One of the lithium minerals most widespread in the earth&apos;s surface is spodumene (Li20-A1203-4Si02), a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Hills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade deposits in forth Carolina. The theoretical lithia (Li20) content of spodumene is 9.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By Murat Alkan

In this study, a self-propagating high-temperature synthesis (SHS) and following acid leaching techniques were carried out to produce boron carbide (B4C) powder. First, B2O3 was obtained through calcinations of H3BO3 at 1073 K for 2 hours. Then, the glassy B2O3 obtained was crushed and sieved. In the SHS experiments, different amounts of B2O3, Mg and C black were used. The SHS product was obtained in the form of black, spongy solid. In the leaching step, the SHS product was leached in a HCl solution to eliminate the MgO and Mg3B2O6. The effect of acid concentration on the selective leaching was studied at different concentration range, solid/liquid (S/L) ratio, and temperature. The products obtained were characterized by using X-ray diffraction, chemical analysis and SEM techniques.

Jan 1, 2009

By J. E. Rourke, O&apos

A wide variety of techniques and equipment are available for coring soft or poorly consolidated geological material. This report presents a comprehensive literature review and evaluation of these techniques and equipment. A potential user will find guidelines in this report to assist him in selecting sampling equipment. A bar chart shows what samplers have been used under what geological conditions, and gives the specific literature references. Two matrices rate the present techniques and equipment with respect to reported success for sampling specific materials, and with respect to several performance characteristics including complexity of use and core quality. These matrices are supplemented with tables of typical sampling equipment. and program costs. Near-term future developments are seen primarily in improved training of drillers, and in instrumenting the drilling operation to provide objective data on drilling characteristics. An extensive annotated bibliography, a catalogue of equipment suppliers including specifications and cost ranges, and a list of manufacturers and distributors are appended to the report.

Jan 1, 1978

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By Türker Hüdaverdi, Özge Akyildiz

"In this research, image analysis technique, Kuz-Ram and KCO Models were used to examineefficiency of the quarry blasts. Investigations were performed in Cendere region, Istanbul. As a firststep, image analysis software was used to determine particle size distribution of muckpiles.Additionally, the results of KuzRam and KCO fragmentation models were compared to the results ofthe image analysis technique. The efficiency of KuzRam and KCO models was investigated and theimportant points to be considered were explained. Additionally, the effect of the rock factor valueson the size distribution curves was investigated. The blasthole diameter is 89 mm. (3.5 in) in thestudied quarry. Each measured blast has a different burden, spacing and stemming length. Blastholes was drilled in a staggered pattern. It is concluded that, KuzRam and KCO models can be successfully used to determine fragment size distribution in Cendere Region Quarries, Istanbul. Site engineers can predict blast fragmentation using the theoretical fragmentation models and they may change blast design parameters before blasting operation if necessary. It is possible to calibrate the Kuz-Ram and KCO fragmentation models using the measurements obtained by image analysis technique."

Jan 1, 2016

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

Worldwide minerals exploration slipped in 1992 from 1991 levels. Although industrial production figures showed the US economy emerging from recession in early 1992, it was not until February 1993 that the lagging indicator of unemployment dropped to 7%. Most other industrialized countries are still in recession. Preliminary data for 1992 showed industrial production dropping in Japan (5%), Germany (1.4%), the United Kingdom (0.5%) and France (1.4%). The slowdown in industrial production led to reduced mineral demand. This resulted in lean cash flows from mining operations, which squeezed exploration funding. Although mineral prices were steady during most of 1992, some mineral commodity prices began falling in late 1992 and early this year. Exploration 1991-1992 According to Metals Economics Group (MEG), planned 1992 exploration expenditures were down by about 5%. Geographically, the leading exploration target was the United States with 21 % of the expenditures, followed by Australia (19%), Canada (18%), Latin America (15%), South Africa (9%) and the western Pacific (7.5%). The remaining 10% was split between Europe and Africa. There were absolute increases in exploration expenditures in the United States and Latin America. Latin America showed the largest increase. The change in the Mexican mining law allowing foreign ownership of mines should result in the inflow of direct foreign investment in Mexico&apos;s mining industry.

Jan 1, 1993

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pressure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water-treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By William N. Patterson

This report describes the design and testing of an improved quiet hard rock percussion drill. The improved drill incorporates a tappetless design with independent rotation in a hand held drill weighing 50 lbm. Laboratory and field testing in three mines were conducted. The testing showed improved drilling performance with no increase in measured noise levels over the fist design.

Jan 1, 1985

A Sun SPARCstation based computer network is utilised to store and process mining data at the Macraes Gold Mine. Techbase and Medsystem software running on the SunOS unix platform is used to generate all data plans, sections and other design data required on a daily basis to run the mining operation. The Macraes site is regarded as a fully integrated site where all geological, grade control, exploration, orebody modelling, resource estimation, pit optimisation and mine design is undertaken on site by MacraesÆ professional staff. The methodologies employed are regarded as æstate-of-the-artÆ where computerisation allows the rapid and efficient evaluation of large quantities of mining data by a handful of professional personnel. Ore reserves are estimated using an indicator kriging method and roving cone pit optimisation, a complex process that would not have been achievable in pre-computing days.

Jan 1, 1992

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By Tyler R. J

Methylene blue dye adsorbs on chalcopyrite concentrates slurried in aqueous solution. Saturation adsorption can be achieved within about 24 hours for dye equilibrium concentrations greater than about 10-5 M. The dsorption coverage is obtained from a measurement of the&apos; colour change of the solution. Comparison with BET measurement of the concentrate surface area shows that 2.4 &#177; 0.1 &#181;mol of methylene blue are adsorbed per square metre of surface accessible to the dye cation. The procedure described can be used as a single-point measurement and values for the surface area can be otained to within about 10 per cent with inexpensive instrumentation.

Jan 1, 1979

Geological hazards such as faulting, basement ridges, and zones of "thin" (&lt; 6 m) coal have a major impact on mining economics of underground operations in Huntly Coalfield. Experience has shown that drillhole-based investigations do not yield sufficiently detailed models of the coal seam to allow management of the planning risks associated with these hazards. Consequently, operational performance is affected by unplanned costs associated with lower productivity, loss of coal reserves, and expensive strata control remedies in problem ground conditions. Huntly Coalfield is a challenging environment for acquisition of good quality seismic reflection data due to the very thick (10-85m) weathering layer. Since 1994, successful acquisition of 2D and 3D data has been achieved through a combination of careful testing of technical parameters and experimental trials prior to committing to production recording. High resolution seismic reflection (HRSR) is proving to be an investigations technique which generates accurate and reliable models of the coal seam and associated structures, such as normal faults and topography of the surface on which the coal seam rests. The HRSR technique has been applied and developed in the Okowhao Sector where Huntly East Mine is developing and extracting coal reserves. Results of a recent 3D survey demonstrate that this technique is capable of revolutionising risk management in mine planning for underground mines in structurally complicated coal deposits.

Jan 1, 1997

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By R. R. Brandenthaler

The development of the Seminole area into one of the major oil-producing sections of the country has been accompanied by many innovations and departures from former methods of development. On July 1, 1929, two years and nine months from the date of discovery, 20,490 acres were considered proved, and additional acreage is constantly being developed. Because of its peculiar conditions, extent, and rapid rate of development, the Seminole area provided numerous problems, the solution of which necessitated research in connection with practical field operation; as a result, there was a radical departure from methods usually employed in the development of a new field in the Mid-Continent area.

Jan 1, 1930

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932