Search Documents

By NONE N

Jan 1, 1963

By Yi Luo

In the study of the topographical effects on surface movement due to underground longwall mining, the factors that affect the incremental horizontal displacements are identified using 10 collected cases. Based on this study, the angle of surface natural slope is the major contributor to the incremental horizontal displacement while the total movement is also playing an important role in some cases.

Jan 1, 1996

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By McLennan R. G

The principle of personal safety is as old as the human race. The application of this principle to industry is of much more recent origin, and may be said to be almost exclusively the product of the twentieth century. The enormous strides in technique and production mode prior to the turn of the century had been achieved without any real regard for the crippled human by-products of that expansive era. It was accepted that. accidents were inevitable and formed part of the price that must be paid for production. It was not until 1885 that the first Workmen's Compensation Act was passed in Germany making the employer financially liable for injuries suffered on his plant.With awakening social conscience came the first organised efforts to reduce accidents in industry. Early 19th century literature dealing with the development of powerdriven machinery and the growth of industry in Europe contains many references to the unsafe and unhealthy working conditions that accompanied the change-over from the home workshop to the industrial plant. By the year 1900, there were in Germany - and a little later in England governmental regulations dealing with the guarding of hazardous machinery. American industry, now the acknowledged leader in industrial safety, admits freely that when an organised safety movement commenced in that country, there was already a considerable amount of information available to them from European experience. The steel industry was well to the fore in this work, and in...

Jan 1, 1957

Factors of importance in the ntilization of coal fines are mentioned, and the results of flotation tests on coal fines from three important coal seams in New South Wales are presented.INTRODUCTIONEconomic utilization of fine coal is an important problem in the Australian coal industry, particularly as the proportion of fines mined is increasing with progressive mechanization.While the use of uncleaned coal fines may be economic, it may be preferable to beneficiate them, but the most economic process must be selected.For beneficiating coal finer than about 28 mesh, froth flotation can be applied, but mining engineers should avoid practices that may be detrimental to flotation. Such practices include the indiscriminate use of water, particularly that containing a wetting' agent, for dust suppression. In addition, clay stemming in wet conditions may produce slimes which could adsorb on coal surfaces, while the use of oils and greases as well as the application of stone dust and chlorides in roadway consolidation may influence adversely fine coal beneficiation.This paper deals with the application of flotation to samples of fine coal from the Bulli, Greta, and Victoria Tunnel seams. In addition a discussion is given of the mineralogical constitution, size analysis, and degree of liberation of ash constituents of the various samples.COAL SAMPLESRepresentative samples of coal from the Bulli, Greta, and Victoria Tunnel seams were obtained for testing.

Jan 1, 1961

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989

Jan 1, 1969

By Agne Rustan

The 9th International Symposium on Rock Fragmentation by Blasting was held in the Granada Conference Centre, Granada, Spain from the 14th - 17th September 2009. The Symposium was preceded by a 1 ½ day Workshop on “Vibrations from Blasting” organized by the initiator Dr. Alex Spathis and his colleague M. J. Noy, both employed at Orica Mining, Australia. Prof. Josè Sanchidrian at the “Universidad Politécnic de Madrid” in Madrid, Spain was the main organizer for both the Workshop and the Symposium. A record number of participants came (292) from a record number of countries (41). There were a total of 14 papers in the Vibrations from Blasting Seminar and 96 papers and 2 Keynote Addresses in the Fragblast 9 Symposium itself. The aim with this paper is to present some results from Fragblast 9 which are of interest for a large target group. One very important result from the Fragblast 9 meeting was that it was decided there that Fragblast 10 will be held in November 2012 New Delhi India.

Jan 1, 2009

By Avis W. Effinger

In conjunction with pilot steamflood tests in the Venango sands of Warren and Venango Counties, Pa., the Marx and Langenheim (4)3 calculations were adapted and programed for digital computer solution to predict test performance. The Monte Carlo technique was incorporated in the calculations to provide values of several variables which could not be adequately defined from available information. The computation methods are explained and the FORTRAN IV program listing is presented. Data and results of the prediction calculations for Venango oil sands are also shown.

Jan 1, 1969

By Steve Kral

The coal mining industry in the western United States is seeing the same boom as the rest of the country and the world. Most coal mines in the West are operating flat out as the nation’s appetite for energy continues to grow. And many of the coal mines have either increased their production capacities or are in the process of doing so. However, transportation issues along with environmental restrictions are keeping many mines from expanding even further. Some coal companies held off on further expansion plans until Congress and President Bush could agree on a national energy policy, one that recognizes coal as the nation’s leading source of electricity. In August, Congress passed and the president signed into law such a measure (see Washington Survey, page 7). The legislation includes research funding for clean coal technologies. So western and eastern coal could become even more important in the national energy picture. This is particularly true as supplies of natural gas diminish and the price of oil continues to increase.

Jan 1, 2005

By A. E. Ketler

This report describes a variety of coal mine lighting projects which were funded by the Bureau of Mines in order to obtain underground lighting experience in support of new lighting requirements for underground coal mines. Low coal and high coal, narrow and wide entries, conventional and continuous mining, ac and dc power, bituminous and anthracite, and machine mounting and area lighting were some of the variables covered in this program. Also evaluated was the OCENCO fluorescent caplamp.

Jan 1, 1979

By X-F Zhao, J-W Li, L-P Zeng

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of Kiruna-type deposits has been ascribed to either immiscible iron phosphate melt separated from silicic magma or precipitation from magmatic-hydrothermal fluids. The early Cretaceous Ningwu volcanic basin in Eastern China contains tens of Kiruna-type iron deposits. The orebodies are mainly hosted within the top zones of subvolcanic dioritic intrusions and along the contacts between these intrusions and adjacent volcanic rocks/strata.The orebodies are commonly associated with widespread brecciation and wall rock replacement. Magnetite formation was closely associated with extensive hydrothermal alteration that may extend kilometres, with both vertical and horizontal zonation. Field and textural data indicate that magnetite formed slightly later than albitisation but coeval with apatite and actinolite. Elemental analysis of magnetite and apatite from ores shows distinct features to those as igneous accessary minerals in the host dioritic intrusions, suggesting a genetic relationship to magmatic-hydrothermal processes. Magnetites have elevated TiO2 (up to 5 wt per cent) and V2O3 (up to 0.7 wt per cent), which implies that they are derived from incipient high-temperature magmatic fluids. It is concluded that the Kiruna-type deposits in the Ningwu basin most likely formed from high-temperature magmatic-hydrothermal fluids. The emplacement of dioritic intrusions into a subvolcanic setting likely plays a critical role in the development of Kiruna-type deposits.CITATION:Zhao, X-F, Zeng, L-P and Li, J-W, 2015. Kiruna-type iron deposits in the Mesozoic Ningwu volcanic basin, Eastern China – origin and relationship to subvolcanic dioritic intrusions, in Proceedings PACRIM 2015 Congress, pp 657–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Jim Frazier

Tradition has often dictated low design load stresses on piles. Such traditions often developed prior to modern static or dynamic pile testing methods and perhaps result from a few limiting situations. These low stress limits were then broadly applied, even in cases where the piles could carry substantially higher loads. With sufficient testing to prove the design, higher design loads may present significant overall savings to the project owner. The cost of the testing then becomes an insignificant cost compared to the potentially great benefit of increased pile loadings. To confirm higher load possibilities for driven piles, the pile is tested either statically or dynamically. Further savings and increased testing efficiency result from remote dynamic pile testing. This paper presents a project where design stresses were considerably increased as a result of additional testing and use of remote dynamic pile testing equipment.

Jan 1, 2002

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

By A-A Latscha, C Boyle

Geological modelling has historically been done using sectional interpretation of paper sections or on a computer screen. Boundaries of geological units or grade shells are interpreted by a geologist section by section and the shapes are drawn onto paper to be digitised later or they are directly digitised into a computer. This approach is referred to as explicit modelling. Such methods are time consuming if there are many section lines or boundaries to be interpreted. The number of metres drilled and resource models made is increasing each year and it will be difficult to keep up using explicit modelling methods. Alternatively, it is possible to use information carried in the drill holes, known geological relationships and point estimation methods in two or three dimensions, to create similar geology boundaries, while eliminating or at least greatly reducing the need to manually interpret and digitise detailed sectional interpretations. Such methods are referred to as implicit modelling and are available in a number of software packages. Implicit modelling approaches have been used in iron ore and found to significantly reduce the time needed for modelling while producing results that are comparable or better than standard explicit modelling approaches. A number of case studies have been undertaken of implicit modelling in iron ore deposits. Stratigraphic surfaces of bedded, folded and faulted iron ore deposits have been modelled in various deposits by Leapfrog Geo, GOCAD (with SKUA) and Vulcan Integrated Stratigraphic Modelling. Leapfrog Mining was used to model iron grade shells at particular cut-off grades. The modelled surfaces are of a high standard equivalent to those that could be produced by traditional explicit modelling but the time required by the implicit methods is far less. Implicit geological modelling is an active area of software development and improvements in software are likely.CITATION:Boyle, C and Latscha, A-A, 2013. Implicit geological modelling of iron ore deposits, in Proceedings Iron Ore 2013 , pp 57-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By W. G. Pariseau

This contribution describes rock mechanics features of the Davis Cavern at the former Homestake Mine in Lead, South Dakota, U.S.A. The mine is located in the northern Black Hills of South Dakota. In 2003 and again in 2008, the mine site was recommended for development as a national Deep Underground Science and Engineering Laboratory (DUSEL) in cooperation with the Sanford Underground Science and Engineering Laboratory under the South Dakota Science and Technology Authority (SDSTA). The original Davis Cavern was excavated about 9.1x16.8x9.7 m high (30x55x32 ft high) in 1965 (Mitchell 2009) at a depth of 1,478 m (4850 ft). The purpose of the cavern was to house apparatus for detecting solar neutrinos. The experiment ultimately proved successful and earned R. Davis a share of the 2002 Nobel Prize in physics. Recently, a new experiment (LUX=Large Underground Xenon detector for dark matter particles and WIMP's=weakly interacting massive particles) was proposed for the Davis Cavern that required an increase in height of 2.4 m (8 ft). For many years, the Homestake gold mine was the deepest operating mine in North America. Development extended to the 8000 Level (2,438 m). The mine closed in 2003. Pumps were shut off and the water level rose to the 4350 Level, about 150 m (500 ft) above the Davis Cavern. Some six years later after selection for DUSEL proposal development by the National Science Foundation (NSF), access to the 4850 Level and the Davis Cavern was regained. Pumping has lowered the water level to well below the cavern floor. Figure 1 shows the layout and location of the Davis Cavern (Cavity). Detector tank, supporting steel, and so forth were subsequently removed. The cavern was re-supported and new access was developed. By August, 2010, 13,000 ft3 had been removed during enlargement and renovation of the Davis Cavern. Figure 2 shows the detector tank under construction in 1965.

Jan 1, 2012

By Alden H. Emery, J. J. Forbes

"IntroductionThe data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in 6 coal-mining States. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand, and transporting it from the working face to the surface. The data thus obtained were considered from two angles - namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be mode to discuss the former factor in this paper.CONDITIONS OF MININGThe mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. .All of the coal mined was bituminous, from beds 30 to 120 inches thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by short-wall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face was done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal, were commonly used although some roof work was done with jack-hammers and a. little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1600 to 3600 pounds. With few exceptions, coal was won at the face by dry methods - that is to say, no water was employed fox wetting down the dust either during undercutting, loading, or transportation."

Feb 1, 1927

By W. W. Stephens

As part of the Bureau of Mines program directed toward more effective utilization of the mineral resources of the United States, a number of processes for production of sponge iron have been investigated. The use of sponge iron as a raw material for production of steels and other ferrous alloys offers several possible advantages over the conventional pig-iron and scrap process, especially for utilization of the smeller, widely distributed iron-ore deposits of the western United States. Although considerable information has been made available on various processes for production of sponge iron, little information 118.6 been published heretofore on the problems and costs involved in melting the sponge iron for production of steel. The present Paper reports the results of tests conducted at the Bureau of Nines pilot plant at Redding, Calif. in which several different types of sponge iron Were used as charge material for production of steel in a 4-ton-capacity basic arc furnace.

Jan 1, 1949

By C. McAllister, D. Preece, J. Berendzen

The Multiple Blasthole Fragmentation (MBF) model was developed recently and has been reported in previous papers. The MBF model accepts inputs from the blast design, such as: location and orientation of each blast hole, stemming length, blast hole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect on fragmentation of delay timing with its associated scatter for each blast hole. MBF has a statistical modeling capability for geological random variation of the attenuation of particle velocities. Also simulated is wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges.

Jan 1, 2016

By Steve Kral

The dramatic rescue of nine Pennsylvania coal miners trapped nearly 90 m (300 ft) underground for77 hours probably would not have happened without the high technology equipment and improved mine rescue training techniques available today. By now, most everyone has heard the story of the accident that occurred at the Quecreek Mine near Somerset, PA. At about 9 pm on Wednesday, July 24, the miners were drilling coal in the room-and-pillar mine. Their drilling accidentally punched through to the adjacent, abandoned Saxman Mine. Old mine maps of the Saxman Mine led Black Wolf Coal, Quecreek’s owners, to believe they were between 60 to 90 m (200 to 300 m) away from the abandoned mine. Those maps proved to be inaccurate.

Jan 1, 2002