Search Documents

By Hemingway P, Boag J

Major operating aspects of the Mary Kathleen Uranium Ltd. treatment plant are discussed with partkular reference to those which are peculiar to this operation.Problems associated with the production of a penalty free uranium oxide product are examined and the methods developed to overcome them are described in detail.INTRODUCTIONMary K,athleen Uranium Ltd. is the largest of the Australian uranium producers. The flow-sheet is based on fine grinding, standard sulphuric acid leach, ion exchange concentration, and magnesia precipitation of the final product, with certain modifications introduced as the result of pilot plant investigations at the South Australian Department of Mines Research Laboratories in Adelaide.The plant commenced operations in June, 1958, attained design tonnlige of 1,120 tons per day in September of that year and has since operated continuously with a throughput in excess of 1,000 tons per day. Pilot plant recommendations generally have been followed, and predicted results have been attained. The only exception has been the silica and rare earth content of the product produced during the early months of operation. Considerable modification of the early resin regeneration techniques resulted in the reduction of the silica content of the product to within specification limits. Research work in the ion exchange section has also resulted in the reduction of the rare earth content of the product to below specification levels. All product now being produced is completely within the agreed specification limits of impurities.

Jan 1, 1961

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

Copper, zinc, lead, and silver in the discordant magmatic-hydrothermal orebody of the Conrad Mine, N.S.W., all have a relatively high mean abundance. Any single concordant sulphide orebody containing the same metals has a similar order of mean abundance of only one or two of these, particularly copper, copper and zinc, or zinc and lead.The relative abundances of the metals in the Conrad orebody vary more widely than in concordant orebodies, and the lead-zinc-silver and copper-zinc-lead relationships are significantly different.INTRODUCTIONIn previous investigations of metal abundances in sulphide ores, the basis of selection of the orebodies was their form, and to some extent their geological setting, rather than hypotheses concerning their origin. In all cases they were generally concordant with the bedding of the sedimentary or meta-sedimentary rocks enclosing them, and most occurred in volcanic-sedimentary sequences. Their mineralogies were simple, and they were copper, copper-zinc, zinc or lead-zinc rich in composition. Most were of the type ascribed by several authors to exhalative-sedimentary processes.In one of these investigations (Stanton, 1958), it was pointed out that since the metals in ores of this type showed similar abundance patterns and behaviour, it would clearly be of interest to examine, and to compare with them, orthomagmatic and vein types, unquestionably derived from their igneous rock associates.The present investigation is concerned with a single orebody, of clearly discordant type, and of indisputable hydrothermal origin. The abundance and behaviour of copper, zinc, lead, and silver have been determined and compared to similar data fOl!' the concordant type. Such a comparison tests the possibility that metal abundance patterns of base metal ores may be indicative of the mode of ore deposition.

Jan 1, 1963

By Evan Bennet

Jul 20, 1955

By Patrick J. Hannigan

The pile foundation designer typically performs a subsurface exploration program and static pile capacity calculations before selecting a pile foundation type, length, and capacity. During construction, a pile installation criterion must be established to meet these design requirements. This installation criterion usually consists of a minimum penetration resistance or blow count to confirm pile capacity and may also include a minimum embedment requirement. This text will focus on use of wave equation analysis and dynamic measurements to meet design requirements. BEFORE THE WAVE EQUATION Since the mid-1800s, over 450 dynamic formulas for pile driving control have proliferated. In their simplest form, these formulas relate hammer energy to the work of soil resistance, or simply: W ? h = R ? s (1) Where W = ram weight h = ram drop height or stroke R = pile capacity s = pile penetration per blow

Jan 1, 1990

By Jorge F. Ponciano

El presente texto plantea una forma de tratamiento de lodos anódicos en la fundición de La Oroya a través de una individualización de los residuos de cobre y plomo, con la finalidad de recuperar los elementos valiosos. También, se analizan los resultados experimentales del esquema propuesto (tratamiento térmico-fusión-reducción) para los lodos anódicos de plomo, así como las ventajas que el nuevo diagrama de flujo aporta. Finalmente se plantean alternativas que procesen los residuos anódicos de cobre, complementando el esquema de los lodos nódicos de plomo, y se dan conclusiones técnico-económico del método innovador en relación al sistema actual.

Apr 1, 1991

By R. S. Bowman, G. S. Austin, J. M. Barker, P. S. Freeman

The physical, chemical and mineralogic characteristics of zeolites allow commercially important applications. While adoption of zeolite technology is slow in the United States compared to other regions of the world, continued testing and research has shown a wide range of uses for these minerals. They are important catalysts in petroleum refining, molecular sieves able to separate gases, and chemically inert carriers of reactants. The zeolite clinoptilolite produced by St. Cloud Mining Company (clino) (SC) is used in animal hygiene and animal feed, especially concentrated animal feeding operations (CAFOs), horticulture, water treatment, floor dry, aquariums, air and other filters, and odour control. Clino can remove cations from solution, and surface-modified zeolite (SMZ) is a sorbent for the removal of anions and neutral organics from water. Specific clino applications are: control of chemical pollution in groundwater, removal of organic compounds from oil field waters, and elimination of pathogens from sewage effluent. Combining the sorption capabilities of SMZ with chemical or biological transformations can yield complete removal of toxic materials from contaminated water. Continued development and marketing of zeolite products will be a growth market far into the future. The CAFO market for zeolites is the most significant growth area in the United States over the next few years. SMZ, currently less than 1% of St. Cloud sales, will continue to gain market penetration for many years.

Jan 1, 2004

By William H. Langer

Large amounts of limestone fines co-produced during the processing of crushed lime-stone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point sources such as cement manufacturing. AWL reactants are readily available, inexpensive and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid. This reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities to within about 10 km (6 miles) of the coastline. The majority of U.S. coastal power-generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufacturers and research scientists. There is a concern that CO2 generated from human activities is contributing to climatic and environmental changes. Approximately one-third of anthropogenic CO2 emissions come from burning fossil fuels to generate electricity. Each power plant is capable of emitting several million tons of CO2 annually. A variety of other industrial processes, such as cement manufacture, oil refining, and iron and steel production, also emit large amounts of CO2. The level of atmospheric CO2 can be reduced by capturing CO2 from point-source emissions and storing or sequestering it in isolation from the atmosphere (U.S. Department of Energy, 2003). In 1999, G.H. Rau and K. Caldeira proposed a geochemistry-based method that is referred to as accelerated weathering of limestone (AWL) in a paper titled ?Accelerating carbonate dissolution to sequester carbon dioxide in the ocean ? geochemical implications.?

Jan 1, 2009

The nature of the specialty glass and ceramic business magnifies the dependency of the ultimate product on the unique properties of their raw materials used to make them. This dependency has implications in the management of risk in the supply process which requires a special procurement organization and program commitment to be successful. The Coming system of managing critical materials and factors in development of alternate new suppliers and products is discussed.

Jan 1, 1989

By Richard K. Sandaas

Start Date: April 4, 1988 Completion Date: Dec. 29, 1989 Contractor: SCI Contractors Past and present transportation centers will come together at International District Station, located at the south entrance to the tunnel next to the turn-of-the-century Union Station train depot. The area will bustle once again with activity as commuters and visitors converge on the modern transit station at the edge of Seattle's International District. Buses coming from south Interstate 5 and Interstate 90 will enter the tunnel through this station. [ ] International District Station is an open-air station, 1,060 feet long and 82 feet wide (about 15,400 cubic yards of concrete were used to build the station). A concrete lid over the southern portion of the station staging area is held in place by 131 support piles. The station will include entrances on Jackson Street and King Street. Union Pacific Realty is planning to build an office and retail complex upon the lid. The station also has an international flair. Symbols of the Chinese zodiac will be etched into the station plaza floor. The station platform walls will be lined with large steel panels embellished with designs in origami?a Japanese folded paper art form. [ ]

Jan 1, 1990

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

By N. L. Ayres

Tendon support systems have been successfully used to stabilize excavations. Tendon support systems are routinely designed using the axial load-bearing capacity of tendons, namely the tensile strength. To attain tensile strength the tendon must be loaded along its length, which often does not occur in practice. Tendons should optimally be installed at 90° to the surface of the excavation to achieve maximum penetration depth, yet this is often not physically or practically possible, and installations at angles less than 90° occur. Furthermore, the intersection of geological features within the rock mass frequently results in complex loading situations on tendons. The position and angle at which loading occurs results in different combinations of tensile and shear forces acting on the tendon, which can impact on the support performance of each unit and ultimately the whole system. All factors that influence the support system should be understood and taken into account to ensure a sound support design. Combination loading situations are further investigated and tested to obtain a better understanding of the mechanisms involved and the effects on tendon load-bearing capacity. Tendon support units were tested at different installation angles to establish the tendon performance, mechanical behaviour, and load capacity during these loading situations. The results and outcomes are aimed at providing rock engineers with additional data and improved understanding of how tendons could perform under certain conditions.

Jan 1, 2014

By G. Gavan

Analysis of reported injuries for off-highway haul trucks indicated that 42.7% were slip and fall, and of these 34.1% occurred mounting and dismounting the machine. Redesign of the lower steps was concluded to provide the most overall improvement for increased safety and accident reduction. Various existing, innovative and conceptual designs were reviewed and evaluated. The most promising candidate designs were the four-spring supported lower steps and the center tube mounted lower steps. Both configurations proved to be viable designs as they passed successfully human factors and survivability tests conducted at a large copper mine.

Jan 1, 1979

By A. W. Fahrenwald

"The rate of progress in the last three years in the development of differential flotation has been rapid beyond the realization of most people. Differential flotation is no longer a ""delicate"" and unreliable process, but is now in wide use. Its ""safety"" is due to the wide use of chemicals which either depress or enhance floatability by definite modification of surfaces.The extent of the development and reliability of differential flotation methods any be emphasized by pointing out that there are now several customall-flotation"" plants in this country treating complex lead-zinc-iron ores from widely separated mines. While these ores differ in chemical composition and apparently in physical nature, the various ores treated in such a plant are passed through the same crushing and grinding equipment and through the same flotation machines and flow sheet with only slight changes, if any, in quantity and kind of chemicals and oils added.Some of the development in differential flotation is due to intelligent research on the part of well-trained chemists and metallurgists; much of It must be attributed to empirical testing.Much of the success in differential flotation is due to more care being given to constant conditions with regard to such factors as (1) fineness of grinding, (2) density of pulp entering flotation machines, (3) quantity and constancy of oils and chemicals added to the pulp, and (4) place of addition of reagents, and time of ""conditioning"" treatment of pulp with reagents."

Aug 1, 1925

By Marvin S. Seppanen

Computer programers are often required to make modifications to unfamiliar Fortran routines. This Bureau of Mines report describes a computer program designed to aid the programer in such a situation by reorganizing: Fortran routines. This reorganization includes a sequential renumbering of the routine's statement numbers, a sequential renumbering, and relocation of format statements, an alphanumeric reordering of dimensioned and typed variables, a uniform pattern of text spacing, and a sequential numbering of the records in the final Fortran routine. The computer program has been extensively tested by the author and has proved to be a valuable tool for reorganizing Fortran routines developed under contract and later utilized by the Bureau, and for preparing routines for publication.

Jan 1, 1975

By D. Harrington

Hatch (260) made the following pertinent statement regarding the present status of engineering design of dust-control equipment: Textbooks on ventilation and engineering handbooks devote little or no space to methods of control of industrial dust, and in the technical journals papers on fundamental engineering design of equipment are conspicuous by their absence. In a recent bibliography of the literature on pneumoconiosis less than 1 percent of the articles dealt with the engineering control of the disease. The science of dust control has not developed beyond the stage of trial and error, and the design of structures for the suppression of dust is based almost entirely upon empirical data together with one or two elementary formulas. The latter were derived from the generalized experience in a limited number of Industries such as woodworking, where conditions and requirements are not at all like those, for example, in a sand-pulverizing plant. Wide experience and good judgment are essential to the proper use of the scanty information that has been collected and systematized. Without attempting to minimize the importance of experience in engineering design, it is necessary to point out that most of the past experience obtained in the empirical design of dust-control equipment was not evaluated by means of quantitative studies of the actual reduction in dust , fence, past experience does not necessarily furnish the proper guide for future design. In fact, recent surveys in certain industries, employing modern methods of investigation, have shown that existing equipment is in many cases inadequate.

Jan 1, 1935

By Liane J. Terrill

Rockbolt failures at the Waste Isolation Pilot Plant have been recorded since 1990 and are categorized in terms of mode of failure. The failures are evaluated in terms of physical location of installation within the mine, local excavation geometry and stratigraphy, proximity to other excavations or shafts, and excavation age. The database of failures has revealed discrete areas of the mine containing relatively large numbers of failures. The results of metallurgical analyses and standard rockbolt load testing have generally been in agreement with the in situ evaluations.

Jan 1, 1995

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996

By Åke Krukka, Heribert F. Broicher

"The iron ores of the Kiruna Mine in Sweden are of exceptional quality but for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998 LKAB has been testing prototypes of LIF Analysers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground the mining engineer supports the efforts of the metallurgist in the processing plant.INTRODUCTIONThe Kiruna Mine of LKAB, Sweden is the largest underground iron ore mine in the world. In the early nineties LKAB decided to develop the Kiruna orebody further down from the 775m main level to a new main level at 1045m. This development programme was realised while in the mineral processing section and in the pellet plant further capacity was added (Wyllie 1996).In addition to deepening of the mine, which opened up 330 million tonnes of ore, the exploitation of the so-called lake ore was included in the future planning, adding another 1 15 million tonnes of mineable ore. At an annual production of approximately 20 million tonnes of ore the Kiruna Mine today looks at a developed ore reserve sufficient for the next 20 years.All of the competitors’ ores traded in the world market are from open pit operations. LKAB compensates for the obvious disadvantages by continuous efforts to make the best possible use of her high quality magnetite ore deposit. This objective is realised by combined efforts in the pellet plant, the mineral processing plant and the mine. Propriety processes, latest big scale equipment and high tech solutions for automation lead to high quality sales products at a reasonable cost."

Jan 1, 2002